Add-On Computer Peripherals (ACP) SFP+ 1310nm LC
Contents
1. 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF 850NM 300M REACH LC e aoo Orn NETWORK TRANSCEIVERS MEMORY UPGRADES 10G SFPP LR AO 10Gbase SFP Transceiver Features e 10Gb s serial optical interface compliant to 802 3ae 10GBASE LR e Electrical interface compliant to SFF 8431 specifications for enhanced 8 5 and 10 Gigabit small from factor pluggable module SFP e 1310NM DFB transmitter PIN photo detector e 2 wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers e Operating case temperature 0 C to 70 C e All metal housing for superior EMI performance e Low power consumption e Advanced firmware allow customer system encryption Information to be stored in transceiver s Cost effective SFP solution enables higher port densities and greater bandwidth Applications High speed storage area network Computer cluster cross connect Customer high_speed data pipes 10GE Storage 8G Fiber Channel Product Description This 1310 nm DFB 10Gigabit SFP transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 10km The SFP LR module electrical interface is compliant to SFI electrical specifications The transmitter input and receiver output impedance is 100 Ohms differential Data lines are internally AC coupled The module differential termination and reduce differential to common mode conver2. Add On Computer 34A Mauchly Irvine CA 92618 Tel 877 292 1701 Fax 949 861 2812 Email sales addoncomputer com Email support addoncomputer com Web http www addoncomputer com AddOn Computer Phone 877 292 1701 Page 10 of 10
3. O O DC Se O uf LL O lt LU D 2 oD Z O LO o 10G SFPP LR AO ANS IYIH 30 ONIN 1NJAJ d OL YINVOD AVIYO If ILON 338 tow D Kam DEE aivisagis LON 338 91 ILOH 335 L S7Ivz 1 W 130 ei CERS a 11310 6 JLON k WIdv JNl dS LNOADIA NNIGOW a il Gi SE eS IECH BEE ae ee 91 ILON w l if SILON 335 Kon E GE d 8 3LON 335 31d 2 NIA H i aed Go SALON 335 Zant lp JLON 735 xO Y IS FLOWN 445 WOU Page 9 of 10 Phone 877 292 1701 AddOn Computer 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF 850NM 300M REACH LC E aoo orn NETWORK TRANSCEIVERS MEMORY UPGRADES Contact Information Add On Computer Inc is a leading supplier of Memory Upgrade Network Transceivers and Network connectivity products to Channel Partners Resellers and OEMs with more than seventeen years of direct industry experience Add On Computer ACP has been the exclusive supplier to Ingram Micro s Memory Upgrades program for the past nine years Add On Computer maximizes profitable opportunities for our partners Our ability to source product worldwide ensures that our pricing will always be competitive Offering turnkey solutions Add On Computer has forged a reputation as a solutions provider delivering high quality cost effective product in a timely and reliable manner Corporate offices
4. pey EE WEE E E Extinction ratio min as TI og Kielen A EE BCEE S SOS Receiver Receive overload max in average power note 05 dBm dBm Operating Reach Receiver sensitivity max in OMA note2 dBm Receiver Reflectance max PQ Vertical eye elosure penalty min note3 Los Assert min dBm Q UJ n 20 Los Dessert max PQ Los Hysteresis min 05 oe E 0 2 0 0 Stressed receiver sensitivity max in OMA note2 dBm Z Stressed eye jitter min note2 Ulp p Receive electrical 3dB upper cut off frequency max 12 3 GH Receiver power damage Max _ it dBm AddOn Computer Phone 877 292 1701 Page 6 of 10 9 12 2 30 12 5 3 1 5 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF EE ele lees NETWORK TRANSCEIVERS MEMORY UPGRADES 1 Average optical power shall be measured using the methods spevified in TIA EIA 455 95 2 Receiver sensitivity is informative Stressed receiver sensitivity shall be measured with conformance test signal for BER 1x 1071 3 Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity They are not the required characteristic of the receiver 4 Power budget is defined as the different between the Rx sensitivity and the Tx Output power of the interface 5 Path penalty is intended as the power penalty of the interface between back to back and the maximum applied dispersion 8 DIGITAL DIAG
5. 4 of 10 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF EE ele lees NETWORK TRANSCEIVERS MEMORY UPGRADES 4 TRANSCEIVER BLOCK DIAGRAM Tx Fault Tx Disable Serial Data Serial Clock Ge Micro Controller lt gt MSA Management RD Soom Pin Tia at ROSA 5 ABSOLUTE MAXIMUM RATING These values represent the damage threshold of the module Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Parameters Symbol Min Unit VEDE Storage Temperature Tc 40 C Operating Case Te 70 oC Temperature Table 2 Absolute Maximum Rating 6 RECOMMENDED OPERATING ENVIRONMENT Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted Parameters Min Typical Max Power Supply Voltage Vor 3 135 3 3 3 465 V Operating Case 25 S Fe e NEEN TL me Table 3 Recommended Operating Environment AddOn Computer Phone 877 292 1701 Page 5 of 10 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF 8 850NM 300M REACH LC an O rn A NETWORK TRANSCEIVERS MEMORY UPGRADES 7 OPTICAL CHARACTERISTICS The following characteristics are defined over the Recommended Operating Environment unless otherwise specified Parameter Values Unit 2 10K Transmitter Transmitter e A EE S A E E Lie ee EE EE Tomea peon
6. EZEL Figure 2 Module Interface to Host 10 11 _ a D BOTTOM OF Top View Towarp Host a BOARD AS oe Boao WITH DIRECTION Top THROUGH EA OF MODULE pn Bong INSERTION Figure 3 Module Contact Assignment AddOn Computer Phone 877 292 1701 Page 3 of 10 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF EE sQ00don NETWORK TRANSCEIVERS MEMORY UPGRADES Beef Symbol Name Description Unit op VEET Module transmitter Ground 4 TX Fault Module Transmitter Fault 3 LVTTL I TX Dis Transmitter Disable Turns off transmitter laser output E LVTTL I O SDA 2 Wire Serial Interface Data Line EC E LVTTL Sek 2 Wire Serial Interface Clock ECH lee ET the module 7 Inwm Rso Receiver Rate Select Receiver Rate Receiver Rate Select kees bs a ope E Eege used 40 Iveep Module Receiver Module Receiver Ground A e e Tz fomo fro Recewerinvened Daia ouput Cis femo ro Recover Data Output potuse a fer Module RevewverGrouna 1 er Moaule Recovers V Suy te or voae Receiver SV Supply a r Module Tansmiter Ground o 18 CML I TD Receiver Non Inverted Data output CML I Transmitter Inverted Data Input po Note 1 Module ground pins GND are isolated from the module case 2 Shall be pulled up with 4 7K 10Kohms to a voltage between 3 15V and 3 45V on the host bard Table 1 SFP Module PIN Definition AddOn Computer Phone 877 292 1701 Page
7. NOSTIC FUNCTIONS The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless otherwise specified It is compliant to SFF8472 Rev10 2 with internal calibration mode For external clibration please contact our sales staff Parameters Symbol Min x Unit Notes Temperature monitor DMI Temp degC Over operating temp absolute error Laser power monitor absolute error DMI_TX RX power monitor DMI_RX 1dBm to 15dBm absolute error range Supply voltage DMI_VCC 0 08 Full operating range monitor absolute error EREECHEN Table 5 Digital diagnostic specification table AddOn Computer Phone 877 292 1701 Page 7 of 10 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF 850NM 300M REACH LC OO cr 9 ELETRICAL CHARACTERISTICS The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified PIN Symbol Min Typical Max Unit Notes Power Consumption 800 W Transmitter Tolerance ST IL LEIT ew olerance Tanon OAVotage fT i am Pw Tero im v TA Data veera moase OO fon pul SS Receiver olerance Rx Out l l Tr Tf 30 20 to Tase Jou EES oo AddOn Computer Phone 877 292 1701 Page 8 of 10 NETWORK TRANSCEIVERS MEMORY UPGRADES NETWORK TRANSCEIVERS MEMORY UPGRADES 11 MECHANICAL Complies with SFF 8432 rev 5 0 LL d LL Se DC on Lu Se L co i Q et
8. Signal is provided Tx_LOS when high indicates an optical signal level below that specified in the relevant standard The Rx LOS contact is an open drain collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4 7 10kQ or with an active termination Power supply filtering is recommended for both the transmitter and receiver The Rx LOS signal is intended as a preliminary indication to the system in which the SFP is installed that the received signal strength is below the specified range Such an indication typically points to non installed cables sia el cables or a disabled failing or a powered off transmitter at the far end of the cable Pin Definition The SFP modules are hot pluggable Hot pluggable refers to plugging or unplugging a module while the host board is powered The SFP host connector is a 0 8mm pitch 20 position right angle improved connector specified by SFF 8083 or stacked connector with equivalent electrical performance Host PCB contacts mates with the host in the order of ground power followed by signal as illustrated by Figure 3 and the contact sequence order listed in Table 2 AddOn Computer Phone 877 292 1701 Page 2 of 10 OO cr NETWORK Moche et MEMORY UPGRADES 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF 850NM 300M REACH LC oe TOWARD Host WITH DIRECTION oF MODULE 17 INSERTION 1 2 gt wo OO cr NETWORK TRANSCEIVERS MEMORY UPGRADES TOWARD B
9. sion for quality signal termination and low EMI SFI typically Oe over 200mm of improved FR4 material or up to about 150mm of standard FR4 with connector The transmitter converts 10Gbit s serial PECL or CML electrical data into serial optical data compliant with the 1OGBASE LR standard An open collector compatible Transmit Disable Tx_Dis is provided A logic 1 or connection on this pin will disable the laser from transmitting A logic O on this pin provides normal opteration The transmitter has a internal automatic power control loop APC to ensure constant optical power output across supply voltage and temperature variations An open collector compatible Transmit Fault TFault is provided TX_Fault is a module output contact that when high AddOn Computer Phone 877 292 1701 Page 1 of 10 10G SFPP LR AO BROCADE 10GBASE SR SFP MMF 850NM 300M REACH LC indicates that the module transmitter has detected a fault condition related to laser operation or safety The TX_Fault output contact is an open drain collector and shall be pulled up to Vcc Host in the host with a resistor in the range 4 7 10kQ TX_Disable is a module input contact When TX_Disable is asserted high or left open the SFP module transmitter output shall be turned off This contact shall be pulled up to VccT with a 4 7kKQ to 10kQ resistor The Receiver converts 10Gbit s serial optical data into serial PECL CML electrical data An open compatible Loss of
Download Pdf Manuals
Related Search