Blade Glimpse FPV BNF
Contents
1. NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby LLC For up to date product literature visit horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND a little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and Cause Serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do2. Moisture causes damage to electronics e Never touch moving parts e Never place any portion of the model in your mouth as it could cause serious injury or even death e Always use fully charged batteries e Always keep transmitter powered on while aircraft is powered e Always remove batteries before disassembly e Always keep moving parts clean e Always keep parts dry E Box Contents Blade Glimpse Quadcopter e 500mAh 15 3 7V 25C Li Po Battery 1 500 mAh USB Charger MLP4DSM Trasnsmitter RTF MLP4DSM Smart Phone Holder RTF N 4 AA Batteries RTF Smart Phone Holder BNF Micro SD card Micro SD to SD Card Adapter Table of Contents First Flight Preparation 6 FIVING 6 Charging WarninS cccccccccscccssecsseecsseesssseescsseesseeessaes 6 Battery T Installing the Transmitter Batteries 7 Installing the Flight Battery 8 Transmitter and Receiver 9 SAFE Technology c cccccccceccsecsssscssesessessssesssreserenens 10 Transmitter 11 Flight Mode and Rate Selection 12 Understanding the Primary Flight Controls 19 LE GOE 14 Flyi
3. not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby LLC This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy Sa ___ _ _ Ne Safety Precautions and Warnings e Always keep a safe distance in all directions around e Never operate your model with low transmitter your model to avoid collisions or injury This model is batteries controlled by a radio signal subject to interference from e Always keep aircraft in sight and under control many sources outside your control Interference can e Always move the throttle fully down at rotor strike cause momentary loss of control e Always operate your model in open spaces away from full size vehicles traffic and people e Always carefully follow the directions and warnings for this and any optional support equipment chargers rechargeable battery packs etc 3 e Always let parts cool after use before touching e Always avoid water exposure to all equipment not Always remove batteries after use specifically designed and protected for this purpose Never operate aircraft with damaged wiring
4. 4 in 1 control unit flashes rapidly indicating it is in bind mode 6 Put the transmitter into bind mode while powering on the transmitter 7 Release the bind button switch after 2 3 seconds The quadcopter is bound when the blue LED on the 4 in 1 control unit turns solid 8 Disconnect the flight battery and power the transmitter off CAUTION When using a Futaba transmitter with a Spektrum module you must reverse the throttle channel and rebind Refer to your Spektrum module manual for binding and failsafe instructions Refer to your Futaba transmitter manual for instructions on reversing the throttle channel LL Gee 9 RIF G MLP4DSM Binding Procedure 1 Disconnect the flight battery from the quadcopter 2 Center all trims on your transmitter 3 Power off the transmitter and fully lower the throttle 4 Connect the flight battery in the quadcopter The LED on the 4 in 1 control unit flashes red during initialization then flashes blue when it is ready to bind 5 When the blue light is flashing push in and hold down the left stick while powering on the transmitter you will hear a click 6 Release the left stick The transmitter will beep and the power LED will blink The quadcopter is bound when the blue LED on the 4 in 1 control unit turns solid 7 Disconnect the flight battery and power the transmitter off you encounter problems obey the binding instructions and refer to the trouble
5. S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modifica tion or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of pur chase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this war ranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service Once assembly
6. pilots who are ready for fast forward flight and aerobatic maneuvers loops rolls etc e Stability mode is shown by the flight control board on the quadcopter glowing solid blue When flown in stability mode the quadcopter will limit the bank angle with full control input and return the aircraft to a neutral flight posi tion when you release the elevator aileron stick This mode is typically preferred by pilots during first time use e Agility mode is shown by the flight control board on the quadcopter glowing solid red When flown in agility mode the model will not return to a neutral flight position when you release the controls This mode is typically preferred by experienced pilots who are ready for fast forward flight and aerobatic maneuvers loops rolls etc Flight mode Dual rate selection selection a Understanding the Primary Flight Controls lf you are not familiar with the controls of your Glimpse quadcopter take a few minutes to familiarize yourself with them before attempting your first flight Throttle Left Side View Left Side View SCA Z Descend Throttle down Rudder left Rudder right Elevator Elevator down Forward Elevator up Aileron Aileron left Aileron right LED Codes Equipment LED Color Status Operation Quadcopter Low Battery Agility Mode RTF Transmitter RTF Transmitter Flying the Quadcopter Takeoff Increase the throttl
7. to anothe another transmitter location and attempt connecting again Crashes immediately upon Propellers in wrong locations or lift off incorrect flight mode selected ay NSC Move aircraft and transmitter to another location and attempt binding again Leave the transmitter powered on Discon nect and reconnect the flight battery to the quadcopter Exploded View Parts Listings Part Description Part Description BLH2200 Glimpse RTF BLH2205 Counter Clockwise Motor Glimpse _ BLH2280 Glimpse BNF 6 BLH2206 Props 4 Glimpse BLH2201 4 in 1 Control Unit Glimpse BLH2207 Main Frame Glimpse BLH2202 Camera Board Glimpse EFLB 500mAh 1 3 7V 25C LiPo BLH2203 Canopy Glimpse 50015250 High Current UMX Connector 4 BLH2204 Clockwise Motor Glimpse Optional Parts Part Description Part Description __ DX5e 5 Transmitter Only DX7 DSMX7 Channel Transmitter Only __ DX6i DSMX 6 Transmitter Only __ DX8 DSMX8 Channel Transmitter Only __ DX7s DSMX7 Channel Transmitter Only _ DX9 DSMX 9 Channel Transmitter Only DX6 6 Transmitter Only __ DX18 DSMX 18 Transmitter Only _ Limited Warranty What this Warranty Covers MAKES NO OTHER WARRANTY OR REPRESENTATION AND Horizon Hobby LLC Horizon warrants to the original purchaser HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES that the product purchas
8. will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appro priate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your origi nal sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon EN Non Warranty Service Discover cards By submitting any item to Horizon for service Should your service not be covered by warranty service you are agreeing to Horizon s Terms and Conditions found on will be completed and payment will be required with our website http www horizonhobby com content _service out notification or estimate of the expense unless the center_render service center expense exceeds 50 of the retail purchase cost By ATTENTION Horizon service is limited to Product com submitting the item for s
9. ba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan All other trademarks service marks or logos are property of their respective owners Patents pending Created 01 15 47233 BLH2200 BLH2280
10. ce for the charger charger Reduced flight time Replace the flight battery and follow the Duis unue poweles 681066 flight battery instructions Make sure the battery is warm room tem Flight conditions might be too cold perature before use Power off the transmitter Move the transmit Transmitter too near aircraft during ter a larger distance from the aircraft Dis binding process connect and reconnect the flight battery to LED on receiver flashes rapidly the aircraft Follow the binding instructions and quadcopter will not respond Bind switch or button was not held Power off transmitter and repeat bind to transmitter during binding while transmitter was powered on process Aircraft or transmitter is too close to large metal object wireless source or another transmitter Less than a 5 second wait between first powering on the transmitter and connecting the flight battery to the quadcopter LED on the receiver flashes The quadcopter is bound to a different Select the correct model memory on the rapidly and the quadcopter will model memory ModelMatch trans transmitter Disconnect and reconnect the not respond to the transmitter mitters only flight battery to the quadcopter after binding Flight battery or transmitter battery charge is too low Replace or recharge batteries Aircraft or transmitter is too close to Move aircraft and transmitter to another large metal object wireless source or aff and transmitter
11. e until the model is approximately 2 ft 600mm off the ground in a low level hover and concentrate on balancing the throttle stick s position so that the quadcopter holds a steady hover altitude In some cases you may need to make a few short hops to an altitude of just a few inches until you become familiar with the control inputs and trim settings required to maintain a steady hover and altitude Hovering The Glimpse quadcopter requires minor throttle adjustments to maintain its altitude in hover Remember to keep these throttle adjustments as minimal as possible Large adjustments could result in a loss of control and or a possible crash COB y While attempting to establish a low level hover check to see if any trim adjustments are required to help keep the quadcopter from constantly drifting in various directions If you find that it constantly drifts without any directional control input land the model before making any adjustments to the trim settings e f the nose of the quadcopter rotates to the left or right adjust the rudder trim e f the quadcopter continually drifts forward or backward adjust the elevator trim e f the quadcopter continually drifts to the left or right adjust the aileron trim Continue making minor trim adjustments until the machine hovers at a low altitude with very little drifting and directional control input If this is your first multicopter or helicopter seek the help of an
12. ed the Product will be free from INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES defects in materials and workmanship at the date of purchase OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR What is Not Covered PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES This warranty is not transferable and does not cover i cosmetic THAT THEY ALONE DETERMINED THAT THE PRODUCT damage 1 damage due to acts of God accident misuse WILL SUITABLY MEET REQUIREMENTS OF THE abuse negligence commercial use or due to improper use INTENDED USE installation operation or maintenance iii modification of or to Purchaser s Remedy any part of the Product iv attempted service by anyone other Horizon s sole obligation and purchaser s sole and exclusive than a Horizon Hobby authorized service center v Product not remedy shall be that Horizon will at its option either i service purchased from an authorized Horizon dealer or vi Product not ii replace any Product determined by Horizon to be defec compliant with applicable technical regulations tive Horizon reserves the right to inspect any and all Product s OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON involved in a warranty claim Service or replacement deci ap NSC O sions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER
13. ervice you are agreeing to payment of pliant in the country of use and ownership If received the service without notification Service estimates are available a non compliant Product will not be serviced Further upon request You must include this request with your item the sender will be responsible for arranging return ship submitted for service Non warranty service estimates will be ment of the un serviced Product through a carrier of the billed a minimum of 72 hour of labor In addition you will be billed choice and at the sender s expense Horizon will for return freight Horizon accepts money orders and cashier s hold non compliant Product for a period of 60 days from checks as well as Visa MasterCard American Express and notification after which it will be discarded Warranty and Service Contact Information Country of Purchase Horizon Hobby Contact Information Address Horizon Service Center servicecenter horizonhobby Repairs and Repair Requests com RequestForm www quickbase com db United States Horizon Product Support bghi7ey8c a GenNewRecord 4105 Fieldstone Rd j Product Technical Assistance of America 998 959 2304 Champaign Illinois 61822 USA sales horizonhobby com Sales 888 959 2304 sales horizonhobby co uk Units 1 4 Ployters Rd Staple Tye Service Parts Sales ane Harlow Essex CM18 7NS United Horizon Hobby Limited 44 0 1279 641 097 King fit Horizon Tech
14. experienced pilot to trim the model for you before making your first flight With your quadcopter properly trimmed and maintaining a stable low level hover practice using the rudder elevator and aileron controls to familiarize yourself with the machine s responses to control inputs Remember to keep the control inputs as minimal as possible NOTICE Crash damage is not covered under warranty Low Voltage Cutoff LVC Once the battery reaches 3V under load the ESC will continuously lower power supplied to the motor until complete shutdown occurs This helps prevent over discharge of the Li Po battery Land immediately once the ESC activates LVC Continuing to fly after LVC can damage the battery cause a crash or both Crash damage and batteries damaged due to over discharge are not covered under warranty Repeatedly flying the aircraft until LVC activates will damage the flight battery Disconnect and remove the Li Po battery from the aircraft after use to prevent trickle discharge During storage make sure the battery charge does not fall below 3V per cell Camera Control and App Function Download and install the Glimpse app to your 5 8 GHz Wi Fi capable smartphone or tablet by searching for Glimpse at the Apple App Store for your iOS device or at Google Play for your Android device e Power on your transmitter and the Glimpse the Wi Fi settings on your smartphone or tablet and connect to the Glimpse network Gli
15. g the flight battery into the lead from the 4 in 1 control unit _JAllow the 4 in 1 control unit to initialize and arm properly _IFly the model Land the model _JUnplug the flight battery from the 4 in 1 control unit Always turn the transmitter off last CAUTION All instructions and warnings must be followed exactly Mishandling of Li Po batteries can result in a fire personal injury and or property damage e NEVER LEAVE CHARGING BATTERIES UNATTENDED e NEVER CHARGE BATTERIES OVERNIGHT e By handling charging or using the included Li Po battery you assume all risks associated with lithium batteries e f at any time the battery begins to balloon or swell discontinue use immediately If charging or discharging discontinue and disconnect Continuing to use charge or discharge a battery that is ballooning or swelling can result in fire e Always store the battery at room temperature in a dry area for best results e Always transport or temporarily store the battery temperature range of 40 120 5 49 e Do not store battery or model in a car or direct sunlight If stored in a hot car the battery can be damaged or even catch fire Sa ___ _ _ E e Always charge batteries away from flammable materials e Always inspect the battery before charging e Always disconnect the battery after charging and let the charger cool between charges e Always constantly monitor the temperature of t
16. harger only uses power from the USB port USB power em ES supplies such as those used to charge cellular s 3 7V 500 mA phones can also be used o_o 2 Connect the battery to the charger as shown in the illustration above When you make the connection successfully the LED on the charger turns solid red indicating charging has begun Charging a fully discharged not over discharged 500mAh battery takes approximately 60 minutes The LED goes out when the charge is complete CHARGING Solid Red LED MAX CHARGE LED OFF 3 Always disconnect the flight battery from the charger immediately upon completion of charging A CAUTION Once charging is complete immediately remove the battery Never leave a battery connected to the charger Installing the Transmitter Batteries RTF Install 4 AA batteries into the transmitter noting polarity Replace the transmitter batteries when the power LED flashes and the transmitter beeps We recommend using only alkaline AA batteries in the transmitter however it is possible to use rechargeable NiMH batteries CAUTION If using rechargeable batteries charge only recharge able batteries Charging non rechargeable batteries may cause the batteries to burst resulting in injury to persons and or damage to property Installing the Flight Battery 1 Lower the throttle and throttle trim to the lowest settings 2 Power on the transmitter 3 Install the bat
17. he battery pack while charging e ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI PO BATTERIES Failure to charge the battery with a compatible charger may cause a fire resulting in personal injury and or property damage e Never discharge Li Po cells to below 3V under load e Never cover warning labels with hook and loop strips e Never charge batteries outside recommended levels e Never charge damaged batteries e Never attempt to dismantle or alter the charger e Never allow minors to charge battery packs e Never charge batteries in extremely hot or cold places recommended between 40 120 F or 5 49 or place in direct sunlight Battery Charging CAUTION Only use chargers specifically designed to charge the included Li Po battery Failure to do so could result in fire causing injury or property damage A CAUTION Never exceed the recommended charge rate The Battery Charger EFLC1013 included with your quadcopter has been designed to safely charge the 15 3 7V 500mAh 25C Li Po flight battery Refer to the charging warnings It is recommended to charge the battery pack while you are inspecting the aircraft The flight battery will be required to confirm proper aircraft operation in future steps NOTICE Inspect the battery to make sure it is not damaged e g swollen bent broken or punctured Charge only batteries that are cool to the touch and are not damaged Insert the charger into a USB port The c
18. ion of the device Compliance Information for the European Union EU Compliance Statement Horizon Hobby LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the R amp TTE EMC and LVD Directives A copy of the EU Declaration of Conformity is available online at http www horizonhobby com content support render compliance Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s respon sibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and Electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and make sure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product C 23 2015 Horizon Hobby LLC Blade E flite Glimpse SAFE the SAFE logo DSM2 DSMX Bind N Fly the BNF logo ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby LLC The Spektrum trademark is used with permission of Bachmann Industries Inc Futa
19. mpse_ using the password 12345678 e Open the Glimpse App on your smartphone or tablet e Place your smartphone in the transmitter holder as shown e Use the onscreen controls as shown on the following page to take photos and video 5 Install the Phone Holder App Controls SD card capacity used Photo button Video record button Retrieving Your Photos and Video The Glimpse quadcopter comes with a micro SD card installed To retrieve your photos and video from the micro SD card you may do either of the following Remove the micro SD card Connect a micro USB cable to the quadcopter e Press and release the p e Insert a micro USB cable micro SD card to remove it not included into the from the quadcopter micro USB port located on e Insert the micro SD card the back of the quadcopter into the provided SD card adapter e Insert the SD card adapter into an SD capable device ENNS E Post Flight Inspection and Maintenance Checklist Cleaning Make sure the battery is not connected before cleaning Remove dust and debris with a soft brush or a dry lint free cloth Replace the motor when the model will not fly steady or veers off when doing a climb out Wiring sure the wiring does not block moving parts Replace damaged wiring and loose connectors Make sure there are no loose screws other fasteners or connectors Do not over tighten metal screws in plas
20. ng the csacsi 14 Components Battery 500mAh 1 3 7V 25C Li Po Included Charger 15 USB Li Po Charger 500 mAh Induded Included Included Transmitter MLP4DSM Low Voltage Cutoff O C siririn 15 Camera Control and App FUNCTION 15 Post Flight Inspection and Maintenance Checklist 17 PAIGE 17 Exploded 19 Parts le tO Sicoeensaessesassennsssanesssanssranasssenasonnsatensaiaerie 20 Optional FANS 20 Limited Warranty cccccccccccssecccsseccseecssetecseeecsseesseeeens 20 Warranty and Service Contact Information 22 FOOL ALON 23 IG Information ccnn 23 Compliance Information for the European 24 Micro SD card Smart Device 5 8 GHz Wi Fi Capable Specifications 6 29 in 160mm 1 97 in 50mm Propeller Diameter 2 36 in 60mm Flying Weight 1 83 02 52 9 To register your product online visit www bladehelis com C i 5s CO First Flight Preparation e Remove and inspect contents e Begin charging the flight battery e Install the flight battery in the quadcopter once it has been fully charged e Program your computer transmitter e Bind your transmitter e Familiarize yourself with the controls e Find a suitable area for flying Charging Warnings Flying Checklist Always turn the transmitter on first Plu
21. nischer Service service horizonhobby de Christian Junge StraBe 1 Sales Horizon Hobby GmbH 49 0 4121 2655 100 25337 Elmshorn Germany France Service Parts Sales infofrance horizonhobby com 11 Rue Georges Charpak Horizon Hobby SAS 33 0 1 60 18 34 90 77127 Lieusaint France China Service Parts Sales info horizonhobby com cn Room 506 No 97 Changshou Horizon Hobby China 86 021 5180 9868 Shanghai China 200060 NY Nie United Kingdom FCC Information This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IC Information CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2 400GHz to 2 4835GHz frequency range This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may Cause undesired operat
22. rim buttons make a sound that increases or decreases in pitch at each pressing The middle or neutral trim position is heard as a middle tone in the pitch range of the sounds The end of the control range is sounded F G Aileron ON OFF Rudder Eleva Trim Switch Trim tor Trim by a series of beeps Power LED flight mode indicator Power LED flight mode indicator Aileron Left Right Throttle Up Down Aileron Left Right Elevator Up Down C Throttle Trim Rudder Left Right Elevator Up Down Eleva tor Trim Rudder Left Right Throttle Up Down Aileron ON OFF Rudder Throttle Trim Switch Trim Trim 11 E Flight Mode and Rate Selection RTF The Glimpse RTF quadcopter comes with the Blade MLP4DSM transmitter This transmitter s flight mode selection feature lets the pilot change between stability mode and agility mode e When powered on this transmitter is automatically in stability mode and high rate Change flight modes by pressing and releasing the left control stick while the transmitter is powered on Change rates by pressing and releasing the right control stick In low rate mode the controls cannot reach their maximum values This mode is typically preferred by pilots looking for smoother easier control response during first time use e n high rate mode the controls can reach their maximum values This mode is typically preferred by experienced
23. setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative Inspection or Services If this Product needs to be inspected or serviced and is compli ant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content _service center_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you
24. shooting guide for other instructions lf needed contact the appropriate Horizon Product Support office For a list of compatible DSM transmitters please visit www bindnfly com 5 Technology Revolutionary SAFE Sensor Assisted Flight Envelope technology uses an innovative combination of multi axis sensors and software that allows model aircraft to know its position relative to the horizon This spatial awareness is utilized to create a controlled flight envelope the aircraft uses to maintain a safe region of bank and pitch angles so you can fly more safely Far beyond stability this level of protection offers multiple modes so the pilot can choose to develop his or her skills with a greater degree of security and flight control that always feels crisp and responsive SAFE technology delivers e Flight envelope protection you can enable at the flip of a switch e Multiple modes to let you adapt SAFE technology to your skill level instantly Best of all sophisticated SAFE technology doesn t require any work to enjoy Every aircraft with SAFE technology is ready to use and optimized to offer the best possible flight experience FlySAFERC com ap NSC RTF Transmitter Control A B H Bind Dual rate Flight mode ee selection sen XS 0 00 VY OWN G lt ION 0 When pressed down t
25. tery by sliding it into the battery mounting slot 4 Connect the battery cable to the 4 in 1 control unit as shown 5 Place the quadcopter upright on a flat surface and leave the aircraft still until the LED on the 4 in 1 control unit is solid blue not blinking CAUTION Always disconnect the Li Po battery from the aircraft when not flying to avoid over discharging the battery Batteries discharged to a voltage lower than the lowest approved voltage may become damaged resulting in loss of performance and potential fire when the batteries are charged Transmitter and Receiver Binding The Glimpse quadcopter requires radio specific setup for basic flight If you are using a computer transmitter simply bind the quadcopter to your transmitter with the model type set to Acro or Airplane mode Binding is the process of programming the receiver to recognize the GUID Globally Unique Identifier code of a specific transmitter You need to bind your chosen Spektrum or DSM2 DSMX technology equipped aircraft transmitter to the receiver for proper operation If you purchased an RTF model the transmitter is bound to the model at the factory To bind or re bind your aircraft to your chosen transmitter please follow the directions below General Binding Procedure 2 Set the model type in your transmitter settings to Acro mode 5 Connect the flight battery in the quadcopter The blue LED on the
26. tic parts Tighten screws so the parts are mated together then turn screw only 1 8th of a turn more Propetiers Make sure there is no damage to the propellers or other parts that move at high speed Damage to these parts includes cracks burrs chips or scratches Replace damaged parts before flying Troubleshooting Guide Problem Possible Cause Solution ee Disconnect the flight battery center the con penta 186 trol trim and re initialize the quadcopter inconsistent or requires extra Battery not correctly placed in Adjust battery position so quadcopter bal trim to neutralize movement battery slot ances in the center of the frame Throttle too high and or throttle trim is Reset controls with the throttle stick too high and throttle trim at the lowest setting Disconnect the flight battery and Quadcopter moved during initialization re initialize the quadcopter while Will not respond to throttle keeping it from moving Disconnect flight battery reverse the throttle Throttle channel is reversed channel on the transmitter recconnect flight battery ee i a 5 ht Flight battery connected with the wrong Replace the 4 in 1 board Connect the flight battery 9 9 polarity battery noting proper polarity N Problem Possible Cause Solution Flight battery charge is low Completely recharge the flight battery Inadequate power to flight battery Use a different USB power sour
Download Pdf Manuals
Related Search