Seagate Pipeline HD ST3500312CS-RF hard disk drive
Contents
1. Serial ATA High Speed Serialized AT Attachment specification 4 1 Hot Plug compatibility Pipeline HD 2 Series SATA drives incorporate connectors which enable you to hot plug these drives in accor dance with the Serial ATA Revision 2 6 specification This specification can be downloaded from www serial ata org Video 3 5 HDD Product Manual Rev J 25 4 2 Serial ATA device plug connector pin definitions Table 7 summarizes the signals on the Serial ATA interface and power connectors Table 7 Serial ATA connector pin definitions Segment Pin Function Definition S1 Ground 2nd mate S2 A Differential signal pair A from Phy S3 A S4 Ground 2nd mate S5 B Differential signal pair B from Phy S6 B Signal S7 Ground 2nd mate Key and spacing separate signal and power segments P1 V33 3 3V power P2 V33 3 3V power P3 V33 3 3V power pre charge 2nd mate P4 Ground 1st mate P5 Ground 2nd mate P6 Ground 2nd mate P7 V5 5V power pre charge 2nd mate Power P8 V5 5V power P9 V5 5V power P10 Ground 2nd mate P11 Ground or LED signal If grounded drive does not use deferred spin P12 Ground 1st mate P13 Vio 12V power pre charge 2nd mate P14 Vio 12V power P15 Vio 12V power Notes 1 All pins are in a single row with a 1 27mm 0 050 in pitch 2 The comments on the mating sequence apply to the case of backplane blindmate connector only In this case the mating2. Idle mode 12 14 Information Technology Equipment ITE 18 Initialize Device Parameters 27 input noise ripple 13 input voltage 12 interface 10 25 interference 19 internal data transfer rate OD 10 ITE 18 K KCC 19 Korean Communications Commission 19 Korean RRL 19 L LBA mode 10 length 11 logical geometry 10 maintenance 18 master slave 2 mounting 23 mounting screws 16 mounting the drive 21 N noise 13 nominal power 11 Nonoperating shock 16 Nonoperating vibration 16 Nonrecoverable read errors 18 O operating 12 Operating power 12 Operating shock 16 Operating vibration 16 P physical characteristics 11 point to point 2 22 power consumption 12 power dissipation 12 power management modes 14 power specifications 12 power on to ready 11 power on hours 18 precautions 21 printed circuit board 21 38 programmable power management 14 prominent discrete tones 17 Q quick reference 3 R radiated RF immunity 17 radio and television interference 19 radio frequency RF 17 Read Buffer 27 Read DMA 27 Read DMA Extended 27 Read DMA without Retries 27 read errors 18 Read Log Ext 27 Read Multiple 27 Read Multiple Extended 27 Read Native Max Address 27 Read Native Max Address Extended 27 Read Sectors 27 Read Sectors Extended 27 Read Sectors Without Retries 27 Read Verify Sectors 27 Read Verify Sectors Extended 27 Read Verify Sectors Without Retries 27 Read write heads 10 Reca
3. 488 397 168 ST3250312CS 488 397 168 ST3160316CS 312 581 808 104 107 ATA reserved 00004 108 111 The mandatory value of the world wide name WWN for the drive Each drive will have a unique NOTE This field is valid if word 84 bit 8 is set to 1 indicating 64 bit value WWN support 112 127 ATA reserved 0000y 128 Security status 0001 y 129 159 Seagate reserved XXXXH 160 254 ATA reserved 00004 255 Integrity word XXA5H Note Advanced Power Management APM and Automatic Acoustic Management AAM features are not supported Note Refer to the bit descriptions below for words 63 84 and 88 of the Identify Drive data Description if bit is set to 1 Bit Word 63 0 Multiword DMA mode 0 is supported 1 Multiword DMA mode 1 is supported 2 Multiword DMA mode 2 is supported 8 Multiword DMA mode 0 is currently active 9 Multiword DMA mode 1 is currently active 10 Multiword DMA mode 2 is currently active Bit Word 84 0 SMART error loggin is supported 1 SMART self test is supported 2 Media serial number is supported 3 Media Card Pass Through Command feature set is supported 4 Streaming feature set is supported 5 GPL feature set is supported 6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported 7 WRITE DMA QUEUED FUA EXT command is supported 8 64 bit World Wide Name is supported 9 10 Obsolete 11 12 Reserved for TLC Video 3 5 HDD
4. EN61000 4 2 95 discharge Radiated RF 80 to 1 000MHz 3V m A EN61000 4 3 96 immunity 80 AM with 1kHz sine ENV50204 95 900MHz 3V m 50 pulse modulation Y 200Hz Electrical fast 1kV on AC mains 0 5kV on external I O B EN61000 4 4 95 transient Surge immunity 1kV differential 2kV common AC mains B EN61000 4 5 95 Conducted RF 150kHz to 80MHz 3Vrms 80 AM with 1kHz sine A EN61000 4 6 97 immunity Voltage dips 0 open 5 seconds C EN61000 4 11 94 interrupts 0 short 5 seconds C 40 0 10 seconds C 70 0 01 seconds B Video 3 5 HDD Product Manual Rev J 17 2 12 Reliability 2 12 1 Annualized Failure Rate AFR The product will achieve an Annualized Failure Rate AFR of 0 55 when operated in an environment of ambient air temperatures of 25 C Operation at temperatures outside the specifications in Section 2 9 may increase the product AFR AFR is a population statistics that is not relevant to individual units AFR specifications are based on the following assumptions for consumer electronics environments 8760 power on hours per year e 10 000 average motor start stop cycles per year Operations at nominal voltages Temperatures outside the specifications in Section 2 9 may reduce the product reliability Normal I O duty cycle for consumer electronics environments Operation at excessive I O duty cycle may degrade product reliability The consumer electronics environment of power on hours tempera
5. Product Manual Rev J 31 13 IDLE IMMEDIATE command with IUNLOAD faeture is supported 14 Shall be set to 1 15 Shall be cleared to 0 Bit Word 88 0 Ultra DMA mode 0 is supported 1 Ultra DMA mode 1 is supported 2 Ultra DMA mode 2 is supported 3 Ultra DMA mode 3 is supported 4 Ultra DMA mode 4 is supported 5 Ultra DMA mode 5 is supported 6 Ultra DMA mode 6 is supported 8 Ultra DMA mode 0 is currently active 9 Ultra DMA mode 1 is currently active 10 Ultra DMA mode 2 is currently active 11 Ultra DMA mode 3 is currently active 12 Ultra DMA mode 4 is currently active 13 Ultra DMA mode 5 is currently active 14 Ultra DMA mode 6 is currently active 32 Video 3 5 HDD Product Manual Rev J 4 3 2 Set Features command This command controls the implementation of various features that the drive supports When the drive receives this command it sets BSY checks the contents of the Features register clears BSY and generates an inter rupt If the value in the register does not represent a feature that the drive supports the command is aborted Power on default has the read look ahead and write caching features enabled The acceptable values for the Features register are defined as follows Table 9 Set Features command values 02H Enable write cache default 03H Set transfer mode based on value in Sector Count register Sector Count register values 00 014
6. equivalent 80 ohm resistive load on the 12V line or an equivalent 15 ohm resistive load on the 5V line e Using 12V power the drive is expected to operate with a maximum of 120mV peak to peak square wave injected noise at up to 10MHz e Using 5V power the drive is expected to operate with a maximum of 100mV peak to peak square wave injected noise at up to 10MHz Note Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read write current 2 8 3 Voltage tolerance Voltage tolerance including noise 5Vt5 e 12V 10 Video 3 5 HDD Product Manual Rev J 13 2 8 4 Power management modes The drive provides programmable power management to provide greater energy efficiency In most systems you can control power management through the system setup program The drive features the following power management modes Power modes Heads Spindle Buffer Active Tracking Rotating Enabled Idle Tracking Rotating Enabled Standby Parked Stopped Enabled Sleep Parked Stopped Disabled Active mode The drive is in Active mode during the read write and seek operations Idle mode The buffer remains enabled and the drive accepts all commands and returns to Active mode any time disk access is necessary Standby mode The drive enters Standby mode when the host sends a Standby Immediate command If the host has set the standby timer the drive can also enter Standby mode automatic
7. of four conductors in two differential pairs plus three ground connec tions The cable size may be 30 to 26 AWG with a maximum length of one meter 39 37 inches Refer to Table 7 for connector pin definitions Either end of the SATA signal cable can be attached to the drive or host For direct backplane connection the drive connectors are inserted directly into the host receptacle The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable For installations which require cables you can connect the drive as illustrated in Figure 2 NN Signal connector Power connector Power cable Figure 2 Attaching SATA cabling Each cable is keyed to ensure correct orientation Pipeline HD 2 Series SATA drives support latching SATA connectors 22 Video 3 5 HDD Product Manual Rev J 3 4 Drive mounting You can mount the drive in any orientation using four screws in the side mounting holes or four screws in the bottom mounting holes Refer to Figure 3 for drive mounting dimensions Follow these important mounting pre cautions when mounting the drive e Allow a minimum clearance of 0 030 inches 0 76mm around the entire perimeter of the drive for cooling Use only 6 32 UNC mounting screws e The screws should be inserted no more than 0 150 inches 3 81mm into the bottom or side mounting holes Do not overtighten the mounting screws maximum torque 6 inch Ib 5
8. regarding Warranty Support visit http Awww seagate com www en us support warranty 4 returns assistance For information regarding data recovery services visit http www i365 com For Seagate OEM and Distribution partner portal visit https direct seagate com portal system For Seagate reseller portal visit http spp seagate com Video 3 5 HDD Product Manual Rev J 35 Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products Seagate distributors OEMs and other direct customers should contact their Seagate Customer Service Operations CSO representative for warranty related issues Resellers or end users of drive products should contact their place of purchase or Seagate war ranty service for assistance Have your serial number and model or part number available Data Recovery Services Seagate offers data recovery services for all formats and all brands of storage media Our data recovery ser vices labs are currently located throughout the world Additional information including an online request form and data loss prevention resources is available at http services seagate com index aspx Authorized Service Centers Seagate Service Centers are available on a global basis for the return of defective products See www seagate com for the service center near you USA Canada Latin America support services For an extensive list of telephone numbers to technical s
9. sequences are the ground pins P4 and P12 the pre charge power pins and the other ground pins the signal pins and the rest of the power pins 3 There are three power pins for each voltage One pin from each voltage is used for pre charge when installed in a blind mate backplane configuration 4 All used voltage pins V must be terminated 26 Video 3 5 HDD Product Manual Rev J 4 3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports For a detailed description of the ATA commands refer to the Serial ATA International Organization Serial ATA Revision 2 6 http www sata io org See S M A R T commands on page 34 for details and subcommands used in the S M A R T implementation Table 8 Supported ATA commands Command name Command code in hex Check Power Mode ESy Configure Stream 514 Device Configuration Freeze Lock B14y C1y Device Configuration Identify B14 C2y Device Configuration Restore B1y COH Device Configuration Set Biy C3y Device Reset 08y Download Microcode 924 Execute Device Diagnostics 90H Flush Cache E7y Flush Cache Extended EA Format Track 504 Identify Device ECH Idle E3H Idle Immediate Ely Initialize Device Parameters 914 Read Buffer ES y Read DMA C8y Read DMA Extended 25H Read DMA Without Retries C94 Read Log Ext 2Fy Read M
10. track 11 track to track seek time 11 tunneling magnetoresistive TMR recording heads 1 U UL60950 1 18 V vibration 16 voltage 12 voltage dips interrupts 17 Voltage tolerance 13 Video 3 5 HDD Product Manual Rev J W warranty 18 weight 11 wet bulb temperature 15 width 11 Write Buffer 28 Write DMA 28 Write DMA Extended 28 Write DMA FUA Extended 0 28 Write DMA Without Retries 28 Write Log Extended 28 Write Multiple 28 Write Multiple Extended 28 Write Multiple FUA Extended 28 Write Sectors 28 Write Sectors Extended 28 Write Sectors Without Retries 28 Write Uncorrectable 28 40 Video 3 5 HDD Product Manual Rev J Seagate Seagate Technology LLC 10200 South De Anza Boulevard Cupertino California 95014 USA Publication Number 100529372 Rev J
11. using a 50 write 50 read algorithm e Standby mode During Standby mode the drive accepts commands but the drive is not spinning and the servo and read write electronics are in power down mode Table 4 DC power requirements Power dissipation 2 disk models Avg watts 25 C Avg 5V typ amps Avg 12V typ amps Spinup 2 0 peak Idle 3 834 0 223 0 226 Operating 4 107 0 295 0 219 Standby 0 699 0 121 0 008 Sleep 0 699 0 121 0 008 Power dissipation 1 disk models Avg watts 25 C Avg 5V typ amps Avg 12V typ amps Spinup 2 0 peak Idle 3 008 0 248 0 147 Operating 3 445 0 316 0 155 Standby 0 707 0 127 0 006 Sleep 0 707 0 127 0 006 During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels Note Drive supports PHY layer power management When enabled a power savings of 300mw can be achieved in Idle Standby and Sleep modes 12 Video 3 5 HDD Product Manual Rev J 2 8 1 1 Typical current profiles Pimec Past Fammi Pam Pan Pion Pda i PE tell 1 1374 303 m Figure 1 Typical 12V startup and operation current profile 2 8 2 Conducted noise Input noise ripple is measured at the host system power supply across an
12. 000 cette 13 2 8 3 Voltage tolerance cotidiana i aA W tats iguanas 13 2 8 4 Power management Modes 14 2 9 Environmental specifications kk kk kk kk kk kK KK KK KK eee 15 2 9 1 Drive case temperature o 15 2 9 2 Temperature gradient iaia i ka kk kk kk E kk E kk kk ka kak k 15 2 9 3 FRUA rta e ee ina 15 2 9 4 ANE ti A 2h i wr Mln Lie i ie ao peli Dili 15 2 9 5 ONOGK See a De On 16 2 9 6 MIDE ON asias a A A RE i Lia a 16 2 10 ACOUSTICS EMISSIONS boost a a ta ele a A ana 17 2 11 Electromagnetic immunity LL 17 2 12 ROMAIN y gt aoc ep tech A TEO A nta 18 2 12 1 Annualized Failure Rate AFR KK kK KK KK K KI KIRI K KIRI K K KIRI KI KK KK KIR 18 2 13 Agency c rtlifiCcaliGfl u ii ble dka kula kl ca dek ia ea 18 2 1311 Safety Certification al dd 18 2 13 2 Electromagnetic compatibility 18 213 3 FCC Vetificatlonis s ad naz E OR 19 2 14 Environmental protection 20 2 14 1 European Union Restriction of Hazardous Substances RoHS Directive 20 2 14 2 China Restriction of Hazardous Substances RoHS Directive 20 2 15 Corrosive environment kk kk kk kk kK KK KK KK KK KK KK KK KK KK KK KK KK KK KK kk 20 Configuring and mounting the drive 0 kk kk kk kk kk kk kk kk kk kk kk kk kk kk kk kk 21 3 1 Handling and static discharge precautions LL 21 3 2 Configuring the drive 22 3 3 Serial ATA cables and connectors 22 3 4 DIV MOU
13. 084 09 OAH OB 0Cy 204 214 224 404 414 424 43H 444 45H 464 Set PIO mode to default PIO mode 2 Set PIO mode to default and disable IORDY PIO mode 2 PIO mode 0 PIO mode 1 PIO mode 2 PIO mode 3 PIO mode 4 default Multiword DMA mode 0 Multiword DMA mode 1 Multiword DMA mode 2 Ultra DMA mode 0 Ultra DMA mode 1 Ultra DMA mode 2 Ultra DMA mode 3 Ultra DMA mode 4 Ultra DMA mode 5 Ultra DMA mode 6 06H Enable the PUIS feature set 074 PUIS feature set device spin up 104 Enable use of SATA features 55H Disable read look ahead read cache feature 82H Disable write cache 864 Disable the PUIS feature sete 904 Disable use of SATA features AA Enable read look ahead read cache feature default F1y Report full capacity available Note At power on or after a hardware or software reset the default values of the features are as indi cated above Video 3 5 HDD Product Manual Rev J 33 4 3 3 S M A R T commands S M A R T provides near term failure prediction for disk drives When S M A R T is enabled the drive moni tors predetermined drive attributes that are susceptible to degradation over time If self monitoring determines that a failure is likely S M A R T makes a status report available to the host Not all failures are predictable S M A R T predictability is limited to the attributes the drive can monitor For more information on S M A R T commands and implementation refer to the D
14. 250412CS ST3250312CS ST3160316CS Formatted capacity 250GB 160GB 512 bytes sector Guaranteed sectors 488 397 168 312 581 808 Heads 1 Disks 1 Bytes per sector 512 Default sectors per track 63 Default read write heads 16 Default cylinders 16 383 Recording density max 1417kb in Track density avg 236 ktracks in Areal density avg 341 5Gb in Spindle speed 5900 RPM Internal data transfer rate max 1285Mb s Sustained data transfer rate max 120MB s VO data transfer rate max 300MB s ATA data transfer modes supported PIO modes 0 4 Multiword DMA modes 0 2 Ultra DMA modes 0 6 Cache buffer Height max 16MB 8MB 20 20mm 0 795 in Width max 101 85mm 4 010 in Length max 146 99mm 5 787 in Weight typical 3959 0 871 Ib Average latency 5 1ms Power on to ready typical lt 6s Standby to ready typical lt 6s Track to track seek time typical lt 1 0ms read lt 1 2ms write Average seek typical lt 14 0ms read lt 15 0ms write Startup current typical 12V peak 2 04 Voltage tolerance including noise 5V 5 12V 10 Operating temperature 0 to 75 C drive case temperature Non operating temperature ambient 40 to 70C Temperature gradient max 20 C per hour operating 30 C per hour non operating Relative humidity Relative humidity gradient max 5 to 90 operatin
15. 5 Minimum multiword DMA transfer cycle time per word 120 nsec 00784 66 A multiword DMA transfer cycle time per word 120 0078 67 Minimum PIO cycle time without IORDY flow control 240 nsec OOFO 68 Minimum PIO cycle time with IORDY flow control 120 nsec 00784 69 74 ATA reserved 0000 75 Queue depth 00004 76 Serial ATA capabilities XXXXH TI Reserved for future Serial ATA definition XXXXH 78 Serial ATA features supported XXXXH 79 Serial ATA features enabled XXXXH 80 Major version number 1F0 81 Minor version number 00004 82 Command sets supported 346B 83 Command sets supported 7D69 84 Command sets support extension Refer to note following this table a Refer to Word 108 111 note 85 Command sets enabled 30XXH 86 Command sets enabled 0001 y 87 Command sets enable extension 40004 88 ala support and current mode Refer to note following this E 89 Security erase time 0000y 90 Enhanced security erase time 00004 92 Master password revision code FFFEY 93 Hardware reset value XXXXH 95 99 ATA reserved 00004 30 Video 3 5 HDD Product Manual Rev J Word Description Value ST31000424CS 1 953 525 168 ST31000322CS 1 953 525 168 Total number of user addressable LBA sectors available Refer to Sor E Slice 100 103 Section 2 2 for related information These words are required for ST3320413CS 625 142 448 drives that support the 48 bit addressing feature Maximum value ST3320311CS 625 142 448 O EEN ST3250412CS
16. 787 MAX 3 1 046 050 546 056 2 PON 5 TYP 4 010 max 3 ed t OF DRIVE TOP OF LABEL 814 t OF CONN DATUM B 1 1221 020 3 mm 3x 56 32 UNC 28 3 MIN THREAD DEPTH 15 MAX FASTENER FENETRAT ION 1 028 MAX UNT ING HOLES BOTH SIDES 3x 2502010 BOTH SIDES 2x 1 6251 020 2x 1 730 E 2x 125 3 4x 6 32 UNC 28 3 MIN THREAD DEPTH 15 MAX FASTENER FEHETRAT IOM MOWNTING HOLES 2x 3 750 3 Recommended case temperature measurement location Figure 3 Mounting dimensions for 1000GB models Video 3 5 HDD Product Manual Rev J 23 1 0462 050 2 as OF DRIVE 4 010 TOP OF LABEL 814 t OF CONN DATUM H i3 1 122 020 3 ATA 6 32 UNG 26 3 MIH THREAD DEPTH 15 M x FASTENER PENETRATION MOUNTING HOLES BOTH SIDES 787 Max 3 3x 250r 010 BOTH SIDES 2x 1 6251 020 2x 125 3 al 4x 6 32 UNC 2B 3 MIN THREAD DEPTH A 15 Max FASTENER PENETRATION e MOUNTING HOLES 2x 3 750 si Recommended case temperature measurement location gt Figure 4 Mounting dimensions for 500 320 250 and 160GB models 24 Video 3 5 HDD Product Manual Rev J 4 0 Serial ATA SATA interface These drives use the industry standard Serial ATA interface that supports FIS data transfers It supports ATA programmed input output PIO modes 0 4 multiword DMA modes 0 2 and Ultra DMA modes 0 6 For detailed information about the Serial ATA interface refer to the
17. A Revision 2 6 specification Yes One Gbyte equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels Video 3 5 HDD Product Manual Rev J 9 2 2 Formatted capacity Formatted Guaranteed Model capacity sectors Bytes per sector ST31000424CS 1000GB 1 953 525 168 ST31000322CS ST3500414CS 500GB 976 773 168 ST3500312CS ST3320413CS 320GB 625 142 448 512 ST3320311CS ST3250412CS 250GB 488 397 168 ST3250312CS ST3160316CS 160GB 312 581 808 One Gbyte equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting 2 2 1 LBA mode When addressing the drive in LBA mode all blocks sectors are consecutively numbered from 0 to n 7 where n is the number of guaranteed sectors as defined above Refer to Section 4 3 1 Identify Device command words 60 61 and 100 103 for additional information about 48 bit addressing support of drives with capacities over 137GB 2 3 Default logical geometry Cylinders Read write heads Sectors per track 16 383 16 63 2 4 Recording and interface technology AII models Interface Serial ATA SATA Perpendicular Recording m
18. FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure not attached as an external device As such each drive is considered to be a subassembly even when it is individually mar keted to the customer As a subassembly no Federal Communications Commission verification or certification of the device is required Seagate has tested this device in enclosures as described above to ensure that the total assembly enclosure disk drive motherboard power supply etc does comply with the limits for a Class B computing device pursu ant to Subpart J Part 15 of the FCC rules Operation with noncertified assemblies is likely to result in interfer ence to radio and television reception Radio and television interference This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer s instructions may cause interference to radio and television reception This equipment is designed to provide reasonable protection against such interference in a residential installa tion However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television which can be determined by turning the equipment on and off you are encouraged to try one or more of the following corrective measures e Reorient the receiving antenna e Move the device to one side
19. MA CA Write DMA Extended 354 Write DMA FUA Extended 3Dy Write DMA Without Retries CBuj Write Log Extended 3Fy Write Multiple C5y Write Multiple Extended 394 Write Multiple FUA Extended CEy Write Sectors 30H Write Sectors Without Retries 31H Write Sectors Extended 344 Write Stream DMA Extended SAY Write Stream Extended 3By Write Uncorrectable 45H 28 Video 3 5 HDD Product Manual Rev J 4 3 1 Identify Device command The Identify Device command command code ECyy transfers information about the drive to the host following power up The data is organized as a single 512 byte block of data whose contents are shown in Table 8 on page 27 All reserved bits or words should be set to zero Parameters listed with an x are drive specific or vary with the state of the drive See Section 2 0 on page 3 for default parameter settings The following commands contain drive specific features that may not be included in the Serial ATA specifica tion Word Description Value Configuration information e Bit 15 0 ATA 1 ATAPI 0 Bit 7 removable media OC5Ay Bit 6 removable controller Bit 0 reserved 1 Number of logical cylinders 16 383 2 ATA reserved 00004 3 Number of logical heads 16 4 Retired 00004 5 Retired 0000 6 Number of logical sectors per logical track 63 003Fy 7 9 Retired 00004 10 19 Serial number 20 ASCII characters 00004 none ASCII 20 Ret
20. NT os _mnggmmn _ estes 23 Serial ATA SATA interface i kk kk kk kk kk kk kk kk kk kk kk kk kk kk kak kk kk kk a kk kk kk 25 4 1 Hot Plug compatibles r E a apra ea eae ae 25 4 2 Serial ATA device plug connector pin definitions anasan KEKE KK KK 26 4 3 Supported ATA commands 27 4 3 1 Identify Device command 29 4 3 2 Set Features command kk kk kk kk kK KK KK KK KK KK KK KK KK KIR KK KK IK KO 33 4 3 3 S M A R T commands 34 Seagate Technology support Services kk kk kk kk kk kk kk kk kk kk kk kk kk kk 35 Pipeline HD 2 Series SATA Product Manual Rev J Pipeline HD 2 Series SATA Product Manual Rev J 1 0 Introduction This manual describes the functional mechanical and interface specifications for the following Seagate Seagate Video 3 5 formerly Pipeline HD 2 model drive ST31000424CS ST3500414CS ST3320413CS ST3250412CS ST31000322CS ST3500312CS ST3320311CS ST3250312CS ST3160316CS These drives provide the following key features High instantaneous burst data transfer rates 3Gb s default Limit settings to 1 5Gb s available via SMART Command Transport command e Perpendicular recording Tunneling Magnetoresistive TMR recording heads and EPRML technology for increased areal density State of the art cache and on the fly error correction algorithms e Native Command Queueing with command ordering to increase performance in demanding applications e Full track multiple sector transfer c
21. Seagate e Product Manual Video 3 5 HDD ST31000424CS ST31000322CS ST3500414CS ST3500312CS ST3320413CS ST3320311CS ST3250412CS ST3250312CS ST3160316CS 100529372 Rev J May 2013 Revision Rev A Rev B Rev C Rev D Rev E Rev F Rev G Rev H Rev J Date 01 07 09 04 29 09 05 19 09 07 08 09 10 29 09 01 05 10 03 02 10 11 28 12 05 24 13 Revision history Sheets affected or comments Initial release as Pipeline HD 2 1 6 17 22 24 32 and 34 fc 1 3 8 10 11 19 and 32 1 5 7 9 25 and 27 28 Updated weight information in Tables 1 3 and physical specifications Fixed Write DMA FUA Extended command Minor text and formatting changes throughout Corrected 320GB model number Updated DC power requirements Table 4 Updated document with new operating and non operating specifications added clearer references to consumer electronics updated section 2 9 1 updated command words 4 3 1 Updated Environmental Specs Updated product name to Video 3 5 HDD throughout Copyright O 2013 Seagate Technology LLC All rights reserved Printed in U S A Publication number 100529372 Rev J May 2013 Seagate Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and or other countries Pipeline HD SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the Uni
22. Shock max 350 Gs at 2ms Vibration operating 5Hz to 22Hz 0 25 Gs 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz 0 25 Gs Vibration non operating 5Hz to 350 Hz 3 0 Gs 350Hz to 500Hz 3 0 Gs Drive acoustics sound power Idle CE Seek Profile 1 9 bels typical 2 1 bels max 2 3 bels typical 2 4 bels max Nonrecoverable read errors 1 per 1015 bits read Annualized Failure Rate AFR Warranty 0 55 To determine the warranty for a specific drive use a web browser to access the following web page support seagate com customer warranty_validation jsp From this page click on the Verify Your Warranty link You will be asked to provide the drive serial number model number or part number and country of purchase The system will dis play the warranty information for your drive Contact start stop cycles 50 000 at 25 C 50 rel humidity Supports Hotplug operation per the Serial ATA Revision 2 6 specification Yes One Gbyte equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels Video 3 5 HDD Product Manual Rev J Table 3 Drive specifications summary for 250 and 160GB models Drive specification ST3
23. ally after the drive has been inactive for a specifiable length of time The standby timer delay is established using a Standby or Idle command In Standby mode the drive buffer is enabled the heads are parked and the spindle is at rest The drive accepts all commands and returns to Active mode any time disk access is necessary e Sleep mode The drive enters Sleep mode after receiving a Sleep command from the host In Sleep mode the drive buf fer is disabled the heads are parked and the spindle is at rest The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host After receiving a reset the drive exits Sleep mode and enters Standby mode with all current translation parameters intact e Idle and Standby timers Each time the drive performs an Active function read write or seek the standby timer is reinitialized and begins counting down from its specified delay times to zero If the standby timer reaches zero before any drive activity is required the drive makes a transition to Standby mode In both Idle and Standby mode the drive accepts all commands and returns to Active mode when disk access is necessary 14 Video 3 5 HDD Product Manual Rev J 2 9 Environmental specifications This section provides the temperature humidity shock and vibration specifications Ambient temperature is defined as the temperature of the environment immediately surrounding the drive Above 1000ft 305 meters the maximum temp
24. apability without local processor intervention e Quiet operation Support for S M A R T drive monitoring and reporting e Supports latching SATA cables and connectors e Supports ATA8 Streaming commands e Supports Power up in Standby feature e Supports Trusted Send Receive Security Protocol Worldwide Name WWN capability uniquely identifies the drive Video 3 5 HDD Product Manual Rev J 1 1 1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional parallel ATA interface The primary advantages include Easy installation and configuration with true plug and play connectivity It is not necessary to set any jump ers or other configuration options Thinner and more flexible cabling for improved enclosure airflow and ease of installation e Scalability to higher performance levels In addition Serial ATA makes the transition from parallel ATA easy by providing legacy software support Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current system and expect all of your existing applications to work as normal The Serial ATA interface connects each disk drive in a point to point configuration with the Serial ATA host adapter There is no master slave relationship with Serial ATA devices like there is with parallel ATA If two drives are attached on one Serial ATA host adapter the host operating system views the t
25. ck to track seek time typical lt 1 0ms read lt 1 2ms write Average seek typical lt 14 0ms read lt 15 0ms write Startup current 12V peak typical 2 0A Voltage tolerance including noise 5V 5 12V 10 Operating temperature 0 to 75 C drive case temperature Non operating temperature ambient 40 to 70 C Temperature gradient max 20 C per hour operating 30 C per hour non operating Relative humidity 5 to 90 operating 5 to 95 non operating Relative humidity gradient max Wet bulb temperature max 30 per hour 37 7 C operating 40 0 C non operating Altitude operating 60 96m to 3 048m 200 ft to 10 000 ft Altitude non operating below mean sea level max 60 96m to 12 192m 200 ft to 40 000 ft Video 3 5 HDD Product Manual Rev J Drive specification ST31000424CS ST31000322CS Operational Shock max 70 Gs at 2ms read 30 Gs at 2ms write Non Operational Shock max 350 Gs at 2ms Vibration operating 5Hz to 22Hz 0 25 Gs 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz 0 25 Gs Vibration non operating 5Hz to350Hz 3 0 Gs 350Hz to 500Hz 3 0 Gs Drive acoustics sound power Idle 2 1 bels typical 2 3 bels max CE Seek Profile 2 4 bels typical 2 5 bels max Nonrecoverable read errors 1 per 1019 bits read Amnualized Failure Rate AFR 0 55 Warranty To determine the warrant
26. erature is derated linearly by 1 C every 1000 ft 2 9 1 Drive case temperature Drive case temperature should be measured at the location indicated in Figure 3 on page 23 Operating drive case temperature 0 to 75 C 32 to 167 F Non operating ambient 40 to 70 C 40 to 158 F Ambient temperature is defined as the temperature of the environment immediately surrounding the drive 2 9 2 Temperature gradient Operating 20 C per hour 68 F per hour max without condensation Non operating 30 C per hour 86 F per hour max 2 9 3 Humidity 2 9 3 1 Relative humidity Operating 5 to 90 noncondensing 30 per hour max Non operating 5 to 95 noncondensing 30 per hour max 2 9 3 2 Wet bulb temperature Operating 37 7 C 99 9 F max Non operating 40 0 C 104 F max 2 9 4 Altitude Operating 60 96m to 3 048m 200 ft to 10 000 ft Non operating 60 96m to 12 192m 200 ft to 40 000 ft Note The recommended storage period e One year under controlled conditions of 34 C 90 RH or less 90 days in uncontrolled storage Video 3 5 HDD Product Manual Rev J 15 2 9 5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws Shock may be applied in the X Y or Z axis 2 9 5 1 Operating shock The drives comply with the performance levels specified in this document
27. es are tested in representative end user systems Although CE marked Seagate drives comply with the directives when used in the test systems we cannot guarantee that all systems will comply with the directives The drive is designed for operation inside a properly designed enclosure with properly shielded I O cable if necessary and terminators on all unused I O ports Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products 18 Video 3 5 HDD Product Manual Rev J Korean RRL If these drives have the Korean Communications Commission KCC logo they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility EMC Framework requirements of the Radio Research Laboratory RRL Communications Commission Republic of Korea These drives have been tested and comply with the Electromagnetic Interference Electromagnetic Susceptibility EMI EMS for Class B products Drives are tested in a representative end user system by a Korean recognized lab Family name Pipeline HD 2 Series Video 3 5 HDD e Certificate number STX PipelineHD2 B in progress Australian C Tick N176 If these models have the C Tick marking they comply with the Australia New Zealand Standard AS NZ CISPR22 and meet the Electromagnetic Compatibility EMC Framework requirements of the Australian Communication Authority ACA 2 13 3
28. ethod Recording density max 1417kb in Track density ktracks inch avg 236 ktracks in Areal density Gbits inch avg 341 5Gb in Spindle speed RPM 5900 0 2 Internal data transfer rate Mb s max 1285Mb s Sustained data transfer rate MB s max 120MB s IO data transfer rate MB s max 300MB s 10 Video 3 5 HDD Product Manual Rev J 2 5 Physical characteristics 1000GB model 500 320 250 and 160GB models Maximum height 26 1mm 1 028 in 20 20mm 0 794 in Maximum width 101 85mm 4 010 in Maximum length 146 99mm 5 787 in Typical weight 615g 1 356 Ib 500 and 320GB models 420g 0 926 Ib 250 and 160GB models 3959 0 871 Ib Cache buffer ST31000424CS ST3500414CS ST3320413CS and 16MB 16 384KB ST3250412CS ST31000322CS ST3500312CS ST3320311CS 8MB 8 192KB ST3250312CS and ST3160316CS 2 6 Seek time Seek measurements are taken with nominal power at 25 C ambient temperature All times are measured using drive diagnostics The specifications in the table below are defined as follows e Track to track seek time is an average of all possible single track seeks in both directions Average seek time is a true statistical random average of at least 5 000 measurements of seeks between random tracks less overhead Typical seek times ms Read Write Track to track lt 1 0 lt 1 2 Average lt 14 0 lt 15 0 Measured in performance mode Meas
29. formation mandated by China s Marking Requirements for Control of Pollution Lam Caused by Electronic Information Products Standard 20 MAREA Zon j PABA EPUP 0 PBST PR d TR m PT Ria E nine Ba Fre KES o Toxic or Hazardous Substances or Elements HET Eat E Hexavalent Polybrominated Polybrominated Biphenyl Diphenyl Ether Name of Parts retires Si E Sem EDP ER r gt O indicates the hazardous and toxic substance content of the part at the homogenous material level is lower than the threshold defined by the China RoHS MCV Standard RRE FERH mR ME eke EMF PERS MCV pve Pre AE X indicates the hazardous and toxic substance content of the part at the homogenous material level is over the threshold defined by the China RoHS MCV Standard RAMI FARMER Peek AAS ie EE PERS MCV ine Pre TAE 2 15 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases chlorine and nitric oxide classes G and H per ASTM B845 However this accelerated testing cannot duplicate every potential application environment Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment The silver copper nickel and gold films used in Seagate products are especiall
30. g 5 to 95 non operating 30 per hour Wet bulb temperature max 37 7 C operating 40 0 C non operating Altitude operating Altitude non operating below mean sea level max 60 96m to 3 048m 200 ft to 10 000 ft 60 96m to 12 192m 200 ft to 40 000 ft Video 3 5 HDD Product Manual Rev J Drive specification Operational Shock max ST3250412CS ST3250312CS ST3160316CS 70 Gs at 2ms read 30 Gs at 2ms write Non Operational Shock max 350 Gs at 2ms Vibration operating Vibration non operating 5Hz to 22Hz 0 25 Gs 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz 0 25 Gs 5Hz to 350Hz 3 0 Gs 350Hz to 500Hz 3 0 Gs Drive acoustics sound power Idle CE Seek Profile 1 9 bels typical 2 1 bels max 2 3 bels typical 2 4 bels max Nonrecoverable read errors 015 1 per 1 bits read Annualized Failure Rate AFR 0 55 Warranty To determine the warranty for a specific drive use a web browser to access the following web page support seagate com customer warranty_validation jsp From this page click on the Verify Your Warranty link You will be asked to provide the drive serial number model number or part number and country of purchase The system will dis play the warranty information for your drive Contact start stop cycles 50 000 at 25 C 50 rel humidity Supports Hotplug operation per the Serial AT
31. ired 00004 21 Retired 04004 22 Obsolete 0000y 23 26 ero revision 8 ASCII character string padded with blanks to end Xe 27 46 Drive model number 40 ASCII characters padded with blanks to end of string 47 Bits 7 0 Maximum sectors per interrupt on Read multiple and Write 8010 multiple 16 H 48 Reserved 0000y 49 Standard Standby timer IORDY supported and may be disabled 2F00y 50 ATA reserved 0000y 51 PIO data transfer cycle timing mode 0200 52 Retired 02004 53 Words 54 58 64 70 and 88 are valid 00074 54 Number of current logical cylinders XXXXH 55 Number of current logical heads XXXXH 56 Number of current logical sectors per logical track XXXXH 57 58 Current capacity in sectors XXXXH 59 Number of sectors transferred during a Read Multiple or Write Multiple Xy command Video 3 5 HDD Product Manual Rev J 29 Word Description Value Total number of user addressable LBA sectors available Refer to Section 2 2 for related information 60 61 268 435 485 sectors 13 08 Drives with capacities over 137GB will OFFFFFFFh have OFFFFFFFh in this field and the actual number of user address able LBAs specified in words 100 103 This is required for drives that support the 48 bit addressing feature 62 Retired 00004 63 ms Ebo DMA active and modes supported Refer to note following xx074 64 Advanced PIO modes supported modes 3 and 4 supported 00034 6
32. librate 27 recording density 10 recording method 10 recording technology 10 relative humidity 15 reliability 18 RMS read write current 13 RoHS 20 RRL 19 S S M A R T Disable Operations 28 S M A R T Enable Operations 28 S M A R T Enable Disable Autosave 28 S M A R T Execute Offline 28 S M A R T implementation 27 S M A R T Read Attribute Thresholds 28 S M A R T Read Data 28 S M A R T Read Log Sector 28 S M A R T Return Status 28 S M A R T Save Attribute Values 28 S M A R T Write Log sector 28 safety certification 18 SATA 25 screws 16 sectors 10 Sectors per track 10 Video 3 5 HDD Product Manual Rev J Security Disable Password 27 Security Erase Prepare 28 Security Erase Unit 28 Security Freeze 28 Security Set Password 28 Security Unlock 28 Seek 28 seek time 11 Serial ATA SATA interface 25 serial ATA ports 2 servo electronics 12 Set Features 28 Set Max Address 28 Set Max Address Extended 28 Set Multiple Mode 28 shock 16 single track seeks 11 Sleep 12 28 Sleep mode 14 Specification summary table 3 spindle speed 10 Spinup 12 Spinup power 12 Standby 12 28 Standby Immediate 28 Standby mode 12 14 standby timer 14 standby to ready 11 start stop times 11 start stop cycles 18 static discharge 21 subassembly 19 support services 35 surge immunity 17 T technical support services 35 temperature 11 15 temperature gradient 15 timers 14 track density 10 track to
33. or the other of the radio or TV e Move the device farther away from the radio or TV e Plug the computer into a different outlet so that the receiver and computer are on different branch outlets If necessary you should consult your dealer or an experienced radio television technician for additional sug gestions You may find helpful the following booklet prepared by the Federal Communications Commission How to Identify and Resolve Radio Television Interference Problems This booklet is available from the Super intendent of Documents U S Government Printing Office Washington DC 20402 Refer to publication num ber 004 000 00345 4 Video 3 5 HDD Product Manual Rev J 19 2 14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide including regulations restricting certain chemical substances 2 14 1 European Union Restriction of Hazardous Substances RoHS Directive The European Union Restriction of Hazardous Substances RoHS Directive restricts the presence of chemi cal substances including Lead Cadmium Mercury Hexavalent Chromium PBB and PBDE in electronic products effective July 2006 This drive is manufactured with components and materials that comply with the RoHS Directive 2 14 2 China Restriction of Hazardous Substances RoHS Directive ri El BR f R2 Hts This product has an Environmental Protection Use Period EPUP of 20 years The following table contains in
34. padded antistatic surface until you mount it in the computer Do not touch the connector pins or the printed circuit board e Do not remove the factory installed labels from the drive or cover them with additional labels Removal voids the warranty Some factory installed labels contain information needed to service the drive Other labels are used to seal out dirt and contamination Video 3 5 HDD Product Manual Rev J 21 3 2 Configuring the drive Each drive on the Serial ATA interface connects point to point with the Serial ATA host adapter There is no master slave relationship because each drive is considered a master in a point to point relationship If two drives are attached on one Serial ATA host adapter the host operating system views the two devices as if they were both masters on two separate ports Both drives behave as if they are Device 0 master devices Serial ATA drives are designed for easy installation It is not necessary to set any jumpers on the drive for proper operation however if you connect the drive and receive a drive not detected error your SATA equipped motherboard or host adapter may use a chipset that does not support SATA speed auto negotiation If you have a motherboard or host adapter that does not support auto negotiation the transfer rate can be lim ited to 1 5GB s via the SMART Command Transport command 3 3 Serial ATA cables and connectors The Serial ATA interface cable consists
35. raft ATA 5 Standard SeaTools diagnostic software activates a built in drive self test DST S M A R T command for D4 that elimi nates unnecessary drive returns The diagnostic software ships with all new drives and is also available at http seatools seagate com This drive is shipped with S M A R T features disabled You must have a recent BIOS or software package that supports S M A R T to enable this feature The table below shows the S M A R T command codes that the drive uses Table 10 S M A R T commands Code in features register S M A R T command DOy S M A R T Read Data D24 S M A R T Enable Disable Attribute Autosave D34 S M A R T Save Attribute Values D4y S M A R T Execute Off line Immediate runs DST D5y S M A R T Read Log Sector D6y S M A R T Write Log Sector D8y S M A R T Enable Operations D9y S M A R T Disable Operations DAY S M A R T Return Status Note If an appropriate code is not written to the Features Register the command is aborted and 0x04 abort is written to the Error register 34 Video 3 5 HDD Product Manual Rev J 5 0 Seagate Technology support services For information regarding online support and services visit http www seagate com www en us about contact _us Available services include e Presales amp Technical support e Global Support Services telephone numbers amp business hours e Authorized Service Centers For information
36. rate max 120 MB s VO data transfer rate max 300 MB s ATA data transfer modes supported PIO modes 0 4 Multiword DMA modes 0 2 Ultra DMA modes 0 6 Cache buffer 16MB 8MB 16MB 8MB Height max 20 20mm 0 795 in Width max 101 85mm 4 010 in Length max 146 99mm 5 787 in Weight typical 420g 0 926 Ib Average latency 5 1ms Power on to ready typical lt 6s Standby to ready typical lt 6s Track to track seek time typical lt 1 0ms read lt 1 2ms write Average seek typical lt 14 0ms read lt 15 0ms write Startup current typical 12V peak 2 0A Voltage tolerance including noise 5V 5 12V 10 Operating temperature 0 to 75 C drive case temperature Non operating temperature ambient 40 to 70 C Temperature gradient max 20 C per hour operating 30 C per hour non operating Relative humidity 5 to 90 operating 5 to 95 non operating Relative humidity gradient max Wet bulb temperature max 30 per hour 37 7 C operating 40 0 C non operating Altitude operating 60 96m to 3 048m 200 ft to 10 000 ft Altitude non operating below mean sea level max 60 96m to 12 192m 200 ft to 40 000 ft Video 3 5 HDD Product Manual Rev J Drive specification Operational Shock max ST3500414CS ST3500312CS ST3320413CS ST3320311CS 70 Gs at 2ms Non Operational
37. s the total A weighted sound power levels for steady state idle and active seek modes of operations Table 5 Drive A weighted Sound Power Levels SWL BA Idle CE seek profile 2 1 bels typ 2 4 bels typ 1000GB models 23 bels max 2 5 bels max 1 9 bels typ 2 3 bels typ 500 320 250 and 160GB models 3 7 pels max 24 bels max 1 During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels Test for Prominent Discrete Tones PDTs Seagate follows the ECMA 74 standards for measurement and identification of PDTs An exception to this pro cess is the use of the absolute threshold of hearing Seagate uses the lower limit for the threshold curve to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA 74 standards Defined as the median curve given by ISO 389 7 Tf curve minus 10dB at all frequencies 2 11 Electromagnetic immunity When properly installed in a representative host system the drive operates without errors or degradation in performance when subjected to the radio frequency RF environments defined in the following table Table 6 Radio frequency environments Test Description Performance level Reference standard Electrostatic Contact HCP VCP 4 kV Air 8 kV B
38. ses the drive and this drive are used throughout this manual to indicate the following drive model ST31000424CS ST3500414CS ST3320413CS ST3250412CS ST31000322CS ST3500312CS ST3320311CS ST3250312CS ST3160316CS 2 1 Specification summary tables The specifications listed in the following tables are for quick reference For details on specification measure ment or definition refer to the appropriate section of this manual Video 3 5 HDD Product Manual Rev J 3 Table 1 Drive specifications summary for 1000GB models Drive specification ST31000424CS ST31000322CS Formatted Capacity 1000GB 512 bytes sector Guaranteed sectors 1 953 525 168 Heads 4 Disks 2 Bytes per sector 512 Default sectors per track 63 Default read write heads 16 Default cylinders 16 383 Recording density max 1417kb in Track density avg 236 ktracks in Areal density avg 341 5Gb in Spindle speed 5900 RPM Internal data transfer rate max 1285Mb s Sustained data transfer rate max 120MB s VO data transfer rate max 300MB s ATA data transfer modes supported PIO modes 0 to4 Multiword DMA modes 0 to2 Ultra DMA modes 0 to 6 Cache buffer 16MB 8MB Height max 26 1mm 1 028 in Width max 101 85mm 4 010 in Length max 146 99mm 5 787 in Weight typical 6159 1 356 Ib Average latency 5 1ms Power on to ready typical lt 12s Standby to ready typical lt 12s Tra
39. ted States and or other countries All other trademarks or registered trademarks are the property of their respective owners When referring to hard drive capacity one gigabyte or GB equals one billion bytes and one terabyte or TB equals one trillion bytes Your computer s operating system may use a different standard of measure ment and report a lower capacity In addition some of the listed capacity is used for formatting and other functions and thus will not be available for data storage Seagate reserves the right to change without notice product offerings or specifications Pipeline HD 2 Series SATA Product Manual Rev J Pipeline HD 2 Series SATA Product Manual Rev J 1 0 2 0 3 0 4 0 5 0 Contents INTRODUCTION ised eer AAA Ria ee 1 1 1 About the Serial ATA interface kk kk kk kk kk kk kK KK KK KK eee 2 BA EDI el r1 e lal eni lola DER DN DD HRH HHHH HHHH HHHH A e A 3 2 1 Specification summary tables 3 2 2 Formatted Capacity 4 0 hk a stg ola Led N N xa Bi Abi ia e aaa 10 2 2 1 LBAMOdE cri el Ee A A w Wn d n 10 2 3 Default logicalgeometry iii ee a a anda Kee wla helk Dees Aaa 10 2 4 Recording and interface technology LL 10 2 5 Physical characteristics si x lt a Le e pak La 11 2 6 Seektime ili pie e ai alati 11 2 7 Start Stop times Kal s ana a a de Wald Skane eee bala OA nad 11 2 8 Power specifications 12 2 8 1 Power consumption ooo 12 2 8 2 Conducted noise 0
40. ture and I O duty cycle affect the product AFR The AFR will be degraded if used in a enterprise application Nonrecoverable read errors 1 per 1015 bits read max Annualized Failure Rate AFR 0 55 nominal power 25 C ambient temperature Contact start stop cycles 50 000 cycles at nominal voltage and temperature with 60 cycles per hour and a 50 duty cycle Warranty To determine the warranty for a specific drive use a web browser to access the fol lowing web page support seagate com customer warranty_validation jsp From this page click on the Verify Your Warranty link You will be asked to provide the drive serial number model number or part number and country of purchase The system will display the warranty information for your drive Preventive maintenance None required 2 13 Agency certification 2 13 1 Safety certification These products are certified to meet the requirements of UL60950 1 CSA60950 1 and EN60950 and so marked as to the certify agency 2 13 2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union EU requirements specified in the Elec tromagnetic Compatibility Directive 2004 108 EC as put into place 20 July 2007 Testing is performed to the levels specified by the product standards for Information Technology Equipment ITE Emission levels are defined by EN 55022 Class B and the immunity levels are defined by EN55024 Driv
41. ty 18 conducted noise 13 conducted RF immunity 17 Configure Stream 27 Configuring the drive 21 connectors 22 corrosive environment 20 CSA60950 1 18 cycles 18 cylinders 10 D data transfer rates 1 DC power 12 default logical geometry 10 density 10 Device Configuration Freeze Lock 27 Device Configuration Identify 27 Device Configuration Restore 27 Device Configuration Set 27 Device Reset 27 dimensions 23 24 Video 3 5 HDD Product Manual Rev J dissipation 12 Download Microcode 27 duty cycle 18 E electrical fast transient 17 Electromagnetic compatibility 18 Electromagnetic Compatibility EMC 19 Electromagnetic Compatibility control Regulation 19 Electromagnetic Compatibility Directive 2004 108 EC 18 electromagnetic immunity 17 electrostatic discharge 17 electrostatic discharge ESD 21 EN 55022 Class B 18 EN 55024 18 EN60950 18 enclosures 19 environmental specifications 15 EPRML 1 error correction algorithms 1 errors 18 ESD 21 EU 18 EU RoHS directive 20 European Union EU requirements 18 Execute Device Diagnostics 27 F FCC verification 19 features 1 Flush Cache 27 Flush Cache Extended 27 Format Track 27 formatted capacity 10 G geometry 10 Gs 16 guaranteed sectors 10 H handling precautions 21 heads 10 height 11 humidity 15 I O data transfer rate 10 I O duty cycle 18 Identify Device 27 Identify Device command 29 Idle 27 37 Idle Immediate 27
42. ultiple C44 Read Multiple Extended 29H Read Native Max Address F8H Read Native Max Address Extended 274 Read Sectors 20H Read Sectors Extended 244 Read Sectors Without Retries 21H Read Stream DMA Extended 2Ay Read Stream Extended 2By Read Verify Sectors 40H Read Verify Sectors Extended 42H Read Verify Sectors Without Retries 414 Recalibrate 104 Security Disable Password FG6H Video 3 5 HDD Product Manual Rev J 27 Command name Command code in hex Security Erase Prepare F34 Security Erase Unit F4y Security Freeze F5y Security Set Password F14 Security Unlock F24 Seek 704 Set Features EFy Set Max Address F94 Note Individual Set Max Address Address 004 commands are identified by the value Password 014 placed in the Set Max Features regis Lock 024 ter as defined to the right Unlock 034 Freeze Lock 044 Set Max Address Extended 37H Set Multiple Mode C6y Sleep E6y S M A R T Disable Operations BO D9 S M A R T Enable Disable Autosave BOy D24 S M A R T Enable Operations BOY D8y S M A R T Execute Offline BO D4y S M A R T Read Attribute Thresholds B04 D1y S M A R T Read Data BO DO S M A R T Read Log Sector BOY D5y S M A R T Return Status B0y DAY S M A R T Save Attribute Values BO D3H S M A R T Write Log Sector BOY D6y Standby E24 Standby Immediate E04 Write Buffer E84 Write D
43. upport presales and warranty service in USA Canada Latin America including business hours go to the Contact Us page on www seagate com Global Customer Support Presales Technical and Warranty Support Call Center Toll free Direct dial USA Canada and Mexico 1 800 SEAGATE 1 405 324 4700 Data Recovery Services Call Center Toll free Direct dial FAX USA Canada 1 800 475 0143 1 905 474 2162 1 800 475 0158 and Mexico 1 905 474 2459 Europe the Middle East and Africa Support Services For an extensive list of telephone numbers to technical support presales and warranty service in Europe the Middle East and Africa go to the Contact Us page on www seagate com Asia Pacific Support Services For an extensive list of telephone numbers to technical support presales and warranty service in Asia Pacific go to the Contact Us page on www seagate com 36 Video 3 5 HDD Product Manual Rev J Index A ACA 19 acceleration 16 acoustics 17 Active mode 14 AFR 18 agency certification 18 altitude 15 ambient temperature 11 12 Annualized Failure Rate AFR 18 areal density 1 10 ATA commands 27 Australia New Zealand Standard AS NZ CISPR22 19 Australian Communication Authority ACA 19 Australian C Tick 19 average seek time 11 B buffer 11 C cables and connectors 22 cache 11 capacity 10 case temperature 15 CE mark 18 certification 18 Check Power Mode 27 China RoHS directive 20 compatibili
44. ured in quiet mode Note These drives are designed to consistently meet the seek times represented in this manual Physical seeks regardless of mode such as track to track and average are expected to meet the noted values However due to the manner in which these drives are formatted benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications 2 7 Start stop times Start stop times s 1000GB models 500 320 250 and 160GB models Power on to Ready typical lt 12 0 lt 6 0 Standby to Ready typical lt 12 0 lt 6 0 Ready to spindle stop max 10 Video 3 5 HDD Product Manual Rev J 11 2 8 Power specifications The drive receives DC power 5V or 12V through a native SATA power connector Refer to Figure 2 on page 22 2 8 1 Power consumption Power requirements for the drives are listed in the table on page 9 Typical power measurements are based on an average of drives tested under nominal conditions using 5V and 12V input voltage at 25 C ambient tem perature e Spinup power Spinup power is measured from the time of power on to the time that the drive spindle reaches operating speed e Idle mode power Idle mode power is measured with the drive up to speed with servo electronics active and with the heads in a random track location e Operating CE seek profile Operating power is measured by simulating a typical PVR operating environment
45. when subjected to a maximum oper ating shock of 70 Gs Read and 30 Gs Write based on half sine shock pulses of 2 msec Shocks should not be repeated more than two times per second 2 9 5 2 Non operating shock The non operating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on a nonrepetitive half sine shock pulse of 2 msec duration 2 9 6 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws Vibration may be applied in the X Y or Z axis 2 9 6 1 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards speci fied in this document are specified below 5Hz to 22Hz 0 25 Gs 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz 0 25 Gs 2 9 6 2 Non operating vibration The maximum non operating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below 5Hz to 350Hz 3 0 Gs 350Hz to 500Hz 3 0 Gs 16 Video 3 5 HDD Product Manual Rev J 2 10 Acoustics emissions Drive emission of sound is measured consistent with the ECMA 74 and its referenced standards Testing is conducted at room temperature approximately 25 degrees C Emission levels are reported a
46. wo devices as if they were both masters on two separate ports This essentially means both drives behave as if they are Device 0 master devices Note The host adapter may optionally emulate a master slave environment to host software where two devices on separate Serial ATA ports are represented to host software as a Device 0 master and Device 1 slave accessed at the same set of host bus addresses A host adapter that emulates a master slave environment manages two sets of shadow registers This is not a typical Serial ATA environment The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software The Command and Control Block registers PIO and DMA data transfers resets and interrupts are all emulated The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device regis ters referred to as the Shadow Register Block All Serial ATA devices behave like Device 0 devices For addi tional information about how Serial ATA emulates parallel ATA refer to the Serial ATA International Organization Serial ATA Revision 2 6 The specification can be downloaded from www sata io org 2 Video 3 5 HDD Product Manual Rev J 2 0 Drive specifications Unless otherwise noted all specifications are measured under ambient conditions at 25 C and nominal power For convenience the phra
47. y for a specific drive use a web browser to access the following web page support seagate com customer warranty_validation jsp From this page click on the Verify Your Warranty link You will be asked to provide the drive serial number model number or part number and country of purchase The system will dis play the warranty information for your drive Contact start stop cycles 50 000 at 25 C 50 rel humidity Supports Hotplug operation per the Yes Serial ATA Revision 2 6 specification One Gbyte equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels Video 3 5 HDD Product Manual Rev J 5 Table 2 Drive specifications summary for 500 and 320GB models Drive specification ST3500414CS ST3500312CS ST3320413CS ST3320311CS Formatted capacity 500GB 320GB 512 bytes sector Guaranteed sectors 976 773 168 625 142 448 Heads 2 Disks 1 Bytes per sector 512 Default sectors per track 63 Default read write heads 16 Default cylinders 16 383 Recording density max 1417kb in Track density avg 236 ktracks in Areal density avg 341 5Gb in Spindle speed 5900 RPM Internal data transfer rate max 1285 Mb s Sustained data transfer
48. y sensitive to the presence of sulfide chlo ride and nitrate contaminants Sulfur is found to be the most damaging In addition electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly PCBA or exposed to an ambient relative humidity greater than 95 Materials used in cabinet fabrication such as vulca nized rubber that can outgas corrosive compounds should be minimized or eliminated The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide free alternatives 20 Video 3 5 HDD Product Manual Rev J 3 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive 3 1 Handling and static discharge precautions After unpacking and before installation the drive may be exposed to potential handling and electrostatic dis charge ESD hazards Observe the following standard handling and static discharge precautions Caution Before handling the drive put on a grounded wrist strap or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet Wear a grounded wrist strap throughout the entire installation procedure Handle the drive by its edges or frame only The drive is extremely fragile handle it with care Do not press down on the drive top cover Always rest the drive on a
Download Pdf Manuals
Related Search