JLab JM-SINGLE-65 flat panel wall mount
Contents
1. i L_E gt MouUnNntTs Designed by JLab in The United States Assembled in China 1 year limited warranty with world class customer support Please contact customer support with any questions or comments at www jlabaudio com support __f L_E gt Mounts INSTALLATION INSTRUCTIONS LD 299 Bi B Pitching angle 20 20 Swivel 180 JLMS LLC suggests you contact a professional to properly install the JLab Mount This JLab Mount must be installed using the supplied hardware with all required lag bolts screwed into the center of the wall studs If you are mounting into concrete or mortar all included anchors and screws must be used By continuing with the installation you agree that JLMS LLC and its affiliates cannot be held liable for damage to equipment including TV s Walls Furniture and Fixtures Additionally JLMS LLC is not responsible for incorrect installation and JLMS LLC and its affiliates cannot be held liable for any injury or death due to improper installation If you question your ability to properly install the JLab Mount please contact a professional Articulating Single Arm TV Mount Fits up to 42 TVs UPC 812887014021 NOTE Read entire instruction sheet before you start installation and assembly A WARNING e Do not begin the installation of this product before you have read and understood the instructions and warnings contained in this installation sheet If you have any questio2. washer x4 M E M F M G M H Cc 13 5x95 5x3 2 x4 wire saddle x2 4mm allen key x2 M I M J M K DODD ST5 5x50 lag bolt x3 concrete anchor x3 D6 6 6x 12 W A W B washer x3 W C Tools required Phillips Head Screw driver 200mm length exclude the handle Electric drill and 8mm masonry bit for concrete wall installation Marking Pen Hammer gt 2 Insert the wire saddle M J to the holes first as shown below wire saddle ml JE E EEJ Woop STUD WALL MOUNTING ZA WARNING e Make sure that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components e Tighten wood screws firmly but do not over tighten Over tightening can damage the screws greatly reducing their holding power e Make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended e Hardware provided is for attachment of mount through standard thickness drywall or plaster into studs Installers are responsible to provide hardware for other types of mounting situations 34 e Use a stud finder to locate the edges of the studs Use of an edge to edge stud finder is highly recommended Based on their edges draw a vertical line down each stud s center
3. appropriate VESA attach the adapter plate to the back of the screen using the appropriate Maintenance combination of screws washers as shown in fig 2 1 and fig 2 2 as shown below Screw must make at least three full turns into mounting hole and fit snugly into place Do not over tighten Repeat for remaining mounting holes level plate and tighten screws Pitching angle adjustment e Use the tilt adjusting knob to adjust you TV to the desired angle the pitching angle can be adjusted between 20 20 as shown fig 3 1 54 Tilt adjusting knob Once you have mounted the bracket and the flat screen check that they are sufficiently secure and safe to Begin with the proper screw hand thread it through the washer and adapter plate into the screen use You should check whether screws are fixed well every two months If you have any doubts regarding the installation please consult our retailer or service department for detail 6
4. e Place wall plate on wall as a template And mark the center of the three mounting holes Make sure that the mounting holes are on the stud centerline Drill three 1 8 3mm dia Holes 1 2 30mm deep Make sure that the wall plate is level secure it using three wood screws W A and three washers W C as shown in fig 1 1 ETY SOLID BRICK AND CONCRETE BLOCK MOUNTING A WARNING e When installing wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block An electric drill should be used on a slow setting to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity e Installer must verify that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components e Use the Wall Plate as a template to mark 3 hole locations on the wall as shown in fig 1 2 e Pre drill these holes with a 8mm masonry bit to at least 60mm in depth Insert a Concrete Anchor W B into each of these holes Attach the Wall Plate to the wall using 3 wood screws W A and 3 Washers W C as in fig 1 3 4 Installing Adapter Plate e Find the
5. n regarding any of the instructions or warnings Please contact your local distributor e Please refer to installation guide recommendation for required distance from wall to avoid risk of property damage e This product should only be installed by someone of good mechanical aptitude with basic building experiences and a full understanding of this manual e Make sure that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components e Never exceed the maximum load capacity e If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended e Always use an assistant or mechanical lifting equipment to safely lift and position equipment e Tighten screws firmly but do not over tighten Over tightening can damage the screws greatly reducing their holding power e This products intended for indoor use only Use of this product outdoors could lead to product failure and personal injury 1 Component Checklist IMPORTANT Ensure you have received all parts against the component checklist prior to installing If any parts are missing or faulty please contact your local distributor for a replacement DDD HDD M4x10 x4 MEx10 x4 Moseo a M8x15 x4 M A D4 04 5x 10 D5 65 5x 12 D6 96 3x016 D8 8 3x 16 washer x4 oo washer x4
Download Pdf Manuals
Related Search