Home
Navilock NL-6003P
Contents
1. NAVILOCK NL 6003P u blox NEO 6P MD6 seriell Receiver Operation manual 62457 1 Introduction The NL 6003P is a MD6 serial GNSS receiver with internal antenna and ublox NEO 6P GPS module This module allows a positioning accuracv of under one metre through a combination of PPP Precision point Positioning and SBAS technologies The MD6 serial interface enables connection to a notebook UMPC tablet or car PC The receiver s bottom side is rubberized and magnetic which allows for universal positioning Thanks to its compact design and its high precision positioning technology it is the ideal companion at work and at leisure Contents e 1x Navilock NL 6003P e 1x 8 cm CD ROM including operation manual Before using the device please make sure that all the parts are included in the package If any parts are missing or damaged please contact your dealer immediately Important health and safety information When using this product take the following precautions in order to avoid possible damages and legal consequences Always follow all safety and operation manuals exactly and keep them for future reference Observe all warnings in the operation manual and on the product In order to avoid injuries electrocution fire and damages to the product observe the following precautions ELECTRIC SECURITY This product is designed for operation with power supply via the USB or PS 2 port Any other operation mode can be dangerous and
2. Select Source 14 Dave AlmanacPlus EJ f Flash update f Start Server u blos5 only Ti Cancel Further information to the u Center can be found in the u blox documentation under http www u blox com products u_center html If you have any questions please contact u blox directly Danger of explosion at contact with fire Do not permanently expose the receiver to temperatures of over 60 C 140 F 8 Possible sources of error and their elimination 8 1 The green LED doesn t light up after the first connection to the USB port Make sure that the PC or notebook is turned on and test the USB port possibly with another USB device If this other USB device works fine please contact the support center If this other USB device works fine please contact the support center 8 2 The green LED continues to light even after a long waiting time but you still don t get a Satfix The NL 6003P needs up to 20 minutes for its first Satfix on another continent To get a Satfix the view to the sky must be unobstructed Move the NL 6003P as far as possible from the wall A house wall reflects the signal strongly and contributes to the Satfix time delay 8 3 Your PC doesn t support the auto start function and doesn t start the CD ROM automatically Please check under http msdn2 microsoft com en us librarv Aa969329 aspx 8 4 The NL 6003P came in touch with jet water water jet from a shower head or strong rain when it was mounted o
3. COM li Xudio Wideo und Gamecoantroller E Bildwerarbeitungsger te il Computer li DVYDACD ROM Laufiwerke 3 LED indicator e flashes with satfix e lights without satfix 4 Application environment The NL 6003P can be used as a MD6 Serial GPS receiver under Windows CE 2000 XP Vista 7 8 The corresponding driver is available on the CD ROM 5 Functional test with u Center 7 xx Download u center from http www navilock de produkte F 1037 NEO 6P 62457 software htmi Install the u center software on vour unit Select the version suitable for vour svstem U center is a pure test program and cannot be used for navigation or orientation It must always be closed after the test It blocks the COM port and does not allow any access of the navigation or route software to the COM port It also serves for updating the Assist GPS data and switching to EGNOS or WAAS etc If the NMEA protocol is displaved in u Center but vou cannot find a receiver in the application software the connection problem is not with the receiver but with the selected software setting In this case the software manufacturer support center may be able to help you 765 4 u u center 7 0 File Edit View Player Receiver Tools Window Help D bi S B2B2HAa BOO HO SCk B M BH BARBER REAR wk wees My jk ET amp E _ _ _______ do 1 2 3 After starting the u Center software check the functionality of your NL 6003P Selecting the
4. GPS receiver The payload of the message consists of various data fields GxGSA GNSS DOP and Active Satellites separated by commas GLGSA GNSS DOP and Active Satellites The payload is followed by a character which identifies the start of the checksum The checksum is a 8 bit exclusive or of all characters between the and the character It is transmitted as two characters representing l the hexadecimal value of the checksum GxGS GNSS Satellites in View GxRMC Recommended Minimum Specific GNSS Data GxVTG Course Over Ground and Ground Speed 0000 24 47 4C 47 4C 4C 2C 35 32 32 34 2E 35 34 33 34 30 2C 4E GLGLL 5224 54340 N 0013 2C 30 31 33 31 36 2E 31 31 35 36 32 2C 45 2C 30 38 34 32 01316 11562 E 0842 0026 31 37 2E 30 30 2c 41 2C 41 24 37 45 OD OA 17 00 4 At7EDOD COM9 19200 u blox 6 No file open NMEA 00 21 09 08 42 17 6 EGNOS configuration with u Center 7 xx Configure SBAS Settings INF dnfMessages A UEX CFG Config SBAS SBAS Settings 333 s ITEM Uamming nterference LIL License LOGFILTER Log settings Subsystem Enabled x MSG Messages Allow test mode use Msg 0 f F il I i in a Li g a t Ta i i Be services v Ranging Use SBAS in NAV NAW Navigation 2 W Apply SBAS Correction data HAWS Navigation 3 Apply mtegrity information NAKS Navigation Expert 5 NMEA NMEA Prgtoc en Number of search channels 3 PM Power Management PA
5. may void the warranty claims for this product This unit contains an internal back up battery NOTE RECYCLE OR DISPOSE OF USED BATTERIES OR RECHARGEABLE BATTERIES IN ACCORDANCE WITH ALL APPLICABLE REGULATIONS AND THE INSTRUCTIONS INCLUDED WITH THE PRODUCT PRECAUTIONS REGARDING DIRECT SUNLIGHT Make sure the unit is not exposed to very high humidity and temperatures Never leave the unit the battery or the rechargeable battery for an extended period in a vehicle or plate where the temperature can increase to over 60 C 140 F for example on the dashboard of a car the window sill or behind a pane of glass which is directly exposed to the sun or very strong UV light Otherwise the unit or the vehicle may be damaged and the battery or the rechargeable battery may overheat Damages requiring repairs Disconnect the unit from the AC supply in the following cases also disconnect the rechargeable battery and contact an authorized repair man or your dealer e Liquid or an object has entered the product e The product has fallen down or was damaged e There are visible signs of overheating e When operated normally the product does not function flawlessly Avoid using the unit directly after strong temperature changes If the unit is exposed to strong temperature and humidity fluctuations condensation can form in the unit In order to avoid damage to the unit please wait until the condensation has dried off before using the unit NOTE If
6. you bring the unit from a cold to a warm environment or vice versa first let it get accustomed to the new temperature before turning it on 2 Starting operation You may connect the NL 6003P either to the serial interface of your PC using an MD6 to DB9 adapter cable or to the USB interface of your PC using an MD6 to USB adapter cable MD6 to DB9 http www navilock de produkte G_61265 merkmale html setLanguage en MD6 to USB http www navilock de produkte G_61264 merkmale html setLanguage en All values for the serial connection via DB9 such as COM Port Baud rate etc result from the settings of this interface on your PC Use the following guide for USB adaptation Plug the USB cable into a free USB connector of your notebook etc Your Windows operating system then detects the NL 6003P and attempts to install a driver When automatic detection does not work install the Prolific USB driver from the supplied CD under the Installation gt NL 6003P menu item Please restart your computer after the installation is completed Afterwards the GPS COM Port will be available in the device manager under connections Set this port in your navigation or route planner software Do not simultaneously use any other program accessing this COM Port G Gerdte Manager es Datei Aktion Ansicht w H E Le a g Karsten TestPC a aS Anschl sse COM amp LPT i Ta Prolific LISB to Serial Comm Port
7. COM port Selecting the baud rate Downloading Assist GPS and updating the receiver Visual display of the NMEA data Configuration manager NMEA UBX message console NMEA text console NOOR WD As seen below you can set up your u Center by yourself Everything important can be connected and displayed immediately The green bars at the bottom of the picture show the reception quality at your position If no bars are displayed please change your position The NL 6003P cannot receive anything in a closed building If the blue bars are displayed the receiver is still acquiring the data and verifying the receipt data u u center 7 0 Messages NMEA File Edit View Player Receiver Tools Window Help DEES gt E S do NMEA Biss 0800 SHEE NMEA 0183 RAHI BIARRB24 GxGG4 Global Positioning System Fix Data GLGGA Global Positioning System Fix Data National Marine Electronics Association Standard for interfacing Marine Electronic Devices GxGLL Geographic Position Latitude Longitude Each NMEA message starts with a character and is terminated with a GLGLL Geographic Position LatitudejLongitude lt cr gt lt If gt carriage return line feed sequence The maximum length of the message is limited to 82 characters including the start and end sequence The start character is followed by an address field which consists of a talker ID and a message identifier The talker ID GP identifies a
8. N Codes AutoScan PI Extended Power Manai C WAAS PRT Ports C EGNOS RATE Rates MSAS RIM CF EITIBTE Ir Werte ry C GAGAN RST Reset mal REN Rec ae f istitut 120 122 124 126 127 123 1 Tel Tire Mark XK send A Poll 38 NL 6003PU use EGNOS as default In the configuration menu you can check these options For detailed information please use the documentation from u blox http www u blox com 7 Assist GPS configuration with u Center 7 xx The NL 6003P supports AssistNowl AssistNow is a standard A GPS service which increases the performance of the GNSS receiver bv calculating a position almost immediatelv even under difficult reception conditions A GPS improves all GNSS capable applications especiallv those that require a continuous state of readiness for example applications for fleet management or GNSS capable hand held devices whose users would like to access local services immediatelv independentiv of the reception conditions Without A GPS a GNSS receiver must localize at least 4 satellites in direct line of vision and then download their location data This process takes 30 seconds under optimal reception conditions but under less favorable conditions it mav take much longer e g in an urban environment or in a building where the GNSS reception is weaker AssistNow sends the data directly to the GNSS receiver thus enabling a quick calculation of the position Assisthow Offline
9. ct brings you fun and enjoyment 9 Specifications Chipset manufacturer tvpe Channels Sensitivitv Frequency C A Code Target precisions GPS Position horizontal u blox NEO 6P GPS 50 channels 160 dBm L1 1575 42 MHz 1 023 MHz SBAS PPP lt 1 m 2D R50 SBAS PPP lt 2 m 3D R50 Demonstrated under following conditions 24 hours stationary first 600 seconds of data discarded HDOP lt 1 5 during measurement period strong signals Continuous availability of valid SBAS correction data during full test period Time Speed Date Protocol Detection rates Hot start Warm start Cold start Re Acquisition Update rate Dynamic prerequisites Acceleration limit Height limit Speed limit Performance Power supply Connection Cable length Operating temperature Dimensions Weight main unit 10 Certificate e CE e FCC 1 microsecond synchronized with GPS time 0 1m s WGS 84 NMEA 0183 V3 01 GGA GSA GSV RMC VTG 1 s average with ephemerides and almanac 32 s average with ephemeredes but without almanac 32 s average neither ephemerides nor almanac 1 s average recovery time after interruption 1 Hz smaller than 4 g 50000 m 500 m s 5 Volt via PS 2 using MD6 to DB9 adapter via USB using MD6 to USB adapter MD6 serial baud rate up to 115 200 preset to 38 400 1 50 m 20 C 65 C 65 mm x 45 mm x 22 mm 789 11 Warrantv period Vour GPS rec
10. eiver will be repaired free of charge within the legal warrantv period unless it was damaged due to external cases humiditv dropping or other damages due to improper usage Your dealer is always ready to help you Please send your unit for repairs directly to Navilock Repair Center Beeskowdamm 13 15 D 14167 Berlin Zehlendorf Postage must always be paid by the client Please add a proof of purchase and a detailed error description Doesn t work or defective is not a detailed error description Time based error meaning how often an error occurs must be expressly mentioned For logistic reasons we cannot accept returned packages without the postage being paid by the client 12 Support For additional support questions please contact our support center support navilock de www navilock com or by telephone 49 30 84716503 You can also call the Service Hotline at the following hours Mo Fr 9 00 am 4 30 pm You will be charged a connection fee for a telephone call to Germany Berlin in accordance with the connection fee overview of your telephone service provider Callers from Germany who subscribed to a national telephone flat rate service and can call nation wide fixed telephone numbers free of charge can call us without incurring additional charges You can also find current product information on our homepage www navilock com 13 Final provision The information and data contained in this manual may be c
11. electronic waste helps to deal with natural resources more economicallv In addition re using electronic waste contributes to the preservation of the environment and human health Additional information regarding the disposal of electric and electronic devices their re usage and the collection sites can be found at vour local authorities disposal companies specialist shops and the manufacturer of the product WEEE note RoHS conformity This product complies with the directive 2002 95 EC of the European parliament and the council from January 27th 2003 concerning the restricted use of dangerous substances in electrical and electronical devices ROHS as well as its modification This product complies with the directive 2011 65 EU from January 3rd 2013 FCC Class An FCC certification of radiation limits on digital devices Class A certification is for business use Class B for residential use is more stringent in order to avoid interference with TVs and other home devices See Part 15 Subpart B of the Federal Register CFR 47 Parts 0 19 EU Import Tragant Handels und Beteiligungs GmbH Beeskowdamm 13 15 14167 Berlin Germany version 07 2013
12. hanged without prior notice Errors and misprints reserved 14 Copyright No part of this instruction manual may be duplicated or transmitted for any purpose and by any means be they electronic or mechanical without the express written authorization from Navilock The brand Navilock is a registered trademark and may not be used without the written authorization of the trademark owner In no case may it be altered or completed by additions 15 Brands of third parties Brands trade names product names and logos of third parties mentioned in this documentation may be trademarks or registered trademarks of the respective owners Conformitv declaration Please download the Declaration of Conformity from http www navilock de support in the conformity area RoHS X CE FC Compliant The WEEE Waste Electrical and Electronic Equipment directive which came into force on 13 February 2003 lead to a comprehensive change in the disposal of used electric products It is the main purpose of this directive to avoid electric waste products WEEE while simultaneously promoting the re usage recycling and other forms of reconditioning in order to reduce the amount of waste The WEEE logo on the product and the package shows that the product should not be disposed of with regular garbage Vou are responsible for disposing all used electric and electronic devices at the corresponding collection sites The separate collection and meaningful re usage of
13. n a car roof Do not connect the receiver with the notebook etc under any circumstances because it will otherwise be completely and irreparably destroyed Return the receiver to our support center mentioning water damage The support center will disassemble the receiver dry it and check its functionality The Navilock repair center tries to be as obliging as possible so please tell us the real reason for the defect During the error analysis we can generally detect if the cause for the defect was an external cause water damage fall over voltage or the wrong handling of the unit Failures are often the result of little causes It is not always necessary to exchange the product immediately because this will not solve the cause of the failure if it is not a GPS hardware problem Before visiting your dealer please contact the Navilock support center They will try to help you quickly and without further ado so that the circumstances of an exchange which might in any case be unnecessary are avoided In this case please write down a detailed description of the error add this information to your end device and the software used in this device as well as the operation environment operating system service pack version CUP size and type storage size hard disk drive and interface etc and send an e mail to support navilock de A support member will look into your problem and work out a solution We hope your Navilock produ
Download Pdf Manuals
Related Search
Related Contents
TE 500 / TE 500-AVR Télécharger - SNUipp/FSU 93 Seine Saint Denis CASQUES AUTO-OBSCURCISSANTS VIKING™ 700G Samsung GALAXY Tab 2 7.0 Wi-Fi Uživatelská přiručka Datamax O'Neil OPT78-2697-01 Hama 00115490 Manuel PACK SERENITE VER 1.0 CEREC 3 - Sirona Support Spare Part List INVACARE ® Dragon Copyright © All rights reserved.
Failed to retrieve file