LG F1422TD washing machine
Contents
1. Tas of Warranty Disposal of your old appliance 1 When this crossed out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002 96 EC All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health For more detailed information about disposal of your old appliance please contact your city office waste disposal service or the shop where you purchased the product What Is Not Covered e Service trips to your home to teach you how to use the product If the product is connected to any voltage other than that shown on the rating plate If the fault is caused by accident neglect misuse or Act of God If the fault is caused by factors other than normal domestic use or use in accordance with the owner s manual e Provide instruction on use of product or change the set up of the product If the fault is caused by pests for example rats or cockroaches etc e Noise or vibration that is considered normal for example water drain sound spin sound or warming beeps e Correcting the installation for example levelling the product adjustment of drain Normal maintenance which recommended by the o2. 1400 rpm F1422TD 1 9 1200 rpm F1222TD 1 9 3 Beep on off e 1000 rpm F1022TD 1 9 Water temperature 60 C Program Cotton The Beep on off function can be set by pressing and holding the Time Delay button simultaneously The Beep on off function can be set at any time and it is automatically canceled when power failure Also the Beep on off function works when power is off Hi to use washer Baby Care7 VE Boiling Care Bio Care D Hand Wash ty Wool 6 Woo Delicate e Spin Ve 1 Dial Program Button Start Pause Button Spin Button Temperature Power 1 2 3 4 1 Power Cotton Quick Synthetic Duvet Bulky e Quick 30 N Rinse Spin 6 7 9 2 SHA1 NO Button 5 6 Button 7 8 Press the Power button to turn power on and off To cancel the Time Delay function the power button should be pressed 2 Initial Program e When the Power button is pressed the washer is ready for Cotton program And the other initial conditions as follows e So if you want to advance into the ashing cycle without changing the program just press the Start Pause button and then the washer will proceed E Initial program e F1422TD 1 9 Cotton Program Main wash Normal Rinse 1400 rpm 60 C e F1222TD 1 9 Cotton Program Main wash Normal Rinse 1200 rpm 60 C e F
3. If these error letters are displayed please refer to the troubleshooting page26 and follow the guide 3 Completion of washing e When washing cycle is completed is displayed on the Multi Erd display 4 Time left e During washing cycle the remaining washing time is displayed e Recommended program by manufacturer Cotton around 1 hour and 54 minutes Cotton Quick around 1 hour and 26 minutes Synthetic around 1 hour and 15 minutes Quick 30 around 30 minutes Hand Wash Wool around 45 minutes Delicate around 51 minutes Duvet around 1 hour and 9 minutes Bulky around 59 minutes Baby Care around 1 hour and 54 minutes Bio Care around 2 hours and 14 minutes Boiling Care around 2 hours and 17 minutes Rinse Spin around 20 minutes Spin around 15 minutes e The washing time may vary by the amount of laundry water pressure water temperature and other washing conditions If an unbalanced load is detected or if the suds removing program operates the wash time may be extended Max increasing time is 45 minutes 24 ii Jaintenance Before cleaning the washer interior unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards When disposing of the appliance cut off the mains cable and destroy the plug Disable the door lock to prevent young children being trapped inside E The water inlet filter IE error me
4. Washing Machine OWNER S MANUAL F1422TD 1 9 F1222TD 1 9 F1022TD 1 9 Thank you for buying a LG Fully Automatic Washing machine Please read your owner s manual carefully it provides instructions on safe installation use and maintenance Retain it for future reference Record the model and serial numbers of your washing machine Pic Features m Protection against creases With the alternate rotation of the drum creasing in the laundry is minimized Built in Heater Internal heater automatically heats the water to the best temperature on selected cycles E More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature and then determines the optimum water level and washing time to minimize energy and water consumption MB Child Lock The Child lock prevents children from pressing any button to change the settings during operation E Low noise speed control system By sensing the amount of load and balance it evenly distributes load to minimize the spinning noise level E Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley C MV CURIS Seren een 3 SDECIIGAIONS ee ee 4 MAS TAMA OMe cacsssccaccanecconaaasatecdcastascenaeetaseansicadstebesess iaeececeseaeseesens 5 Care before WASNING cccccccccccccceeeeseesseeeseseseeeeeeeeeeeeeesseeseees 11 Adding detergent se 12 F ON eae E E E sac tenttoseteseaeae
5. C Intensive 8 0 kg cotton underwear Pre Wash Crease Care Ste Polyamide Acryic Polyester ve Hid 40 C H g Cold 30 C Intensive Cotton which is lightly soiled 60 C Pre Wash Less than Crease Care 8 0 kg Colored Laundry which is lightly Less than soiled fast 30 C 2 0 kg Delicate laundry easily damaged Oe Less than Delicate l silk curtains 2 0 kg Hand sey RANO WARN marked delicate and Intensive Less than Wool machine wash wool laundry 40 C Crease Care 2 0 kg Cotton bedding with filling duvet Cold 30 C ee pillow blanket sofa cover with ing size light filling 9 dog Thick laundry absorbing much Less than water Jumper 8 0 kg j Less than Baby Care Laundry for infant Cot a 40 95 C Medic Rinse zu i For elimination of protein stains 60 C a um Bio Care p 95 C Pre Wash 8 0 kg Crease Care Boiling C For elimination of remnant Less than omng are detergent after boiling wash 8 0 kg Water Temperature Select the water temperature to the wash cycles Always follow garment manufacture s care label or instructions when laundering Medic Rinse For high effectiveness or more purity in rinse operation you can choose Medic Rinse option Pre Wash If the laundry is heavily soiled Pre Wash Course is recommended Intensive When washing heavily soiled laundry you can increase effectiveness by choosing Intensive option Program setting with Cotton 60 C Intens
6. e The installation surface must be clean free from floor wax and other lubricant coatings e Do not let the feet of the washer get wet If feet of the washer get wet slipping may occur 10 Kar before washing E Before the first washing Select a cycle COTTON 60 C add a half load of detergent allow the unit to wash without clothing This will remove residues and water from the drum that may have been left during manufacturing E Caring before washing 1 Care Labels Look for a care label on your clothes This will tell you about the fabric content of your garment and how it should be washed 2 Sorting To get the best results Sort clothes into loads that can be washed with the same wash cycle Water temperature and spin speed and different fabrics need to be washed in different ways Always sort dark colors from pale colors and whites Wash separately as dye and lint transfer can occur causing discoloration of white etc If possible do not wash heavily soiled items with lightly soiled one Soil Heavy Normal Light Separate clothes according to amount of soil Color White Lights Darks Separate white fabrics from colored fabrics Lint Lint producers Collectors Wash lint producers and lint collectors separately 3 Caring before loading E Combine large and small items in a load Load large items first Large items should not be more than half the total wash load Do not wash single items This may cause an out of ba
7. 1022TD 1 9 Cotton Program Main wash Normal Rinse 1000 rpm 60 C Button Button Medic Rinse C N powa C re Was bee Intensive Q rease Care C Press amp qHold 3sec for Tub Clekn Function Power Medic Rinse Pre Wash Intensive Detecting Wash Rinse Spin O 1400 lt O9g5 C O 800 O60 O 400 gt 040 ONoSpin O30 O Rinse Hold O Cold s 3 4 12 5 9 Button Crease Care 10 Child Lock 11 Tub Clean 12 Button Time Delay Program Baby Care Cotton Quick Boiling Care Synthetic Bio Care Duvet Hand Wash Kuh Bulky Wool 6 e Quick 30 N Rinse Spin Delicate e Spin N 13 programs are available according to the laundry type e Lamp will light up to indicate selected program e When Start Pause button is pressed the Cotton program is automatically selected By turning the Program dial the program is selected in order of Cotton Cotton Quick Synthetic Duvet Bulky Quick 30 Rinse Spin Spin Delicate Hand Wash Wool Bio Care Boiling Care Baby Care Regarding to the laundry type for each program Please refer to the pagel4 Hi to use washer Start Pause e This Start Pause button is used to start wash cycle or pause the wash cycle 1 Start 2 Pause If temporary stop of wash cycle is needed press the Start Pause button When in Paus
8. If the appliance is delivered in the winter months and temperatures are below freezing Place the washing machine at room temperature for a few hours before putting it into operation CAUTION CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit that is a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits Check the specification page of this owner s manual to be certain Do not overload wall outlets Overloaded wall outlets loose or damaged wall outlets extension cords frayed power cords or damaged or cracked wire insulation are dangerous Any of these conditions could result in electric shock or fire Periodically examine the cord of your appliance and if its appearance indicates damage or deterioration unplug it discontinue use of the appliance and have the cord replaced with an exact replacement part by an authorized servicer Protect the power cord from physical or mechanical abuse such as being twisted kinked pinched closed in a door or walked upon Pay particular attention to plugs wall outlets and the point where the cord exits the appliance E Washing Machine is to be connected to the water mains using new hose sets and old hose sets should not be used E Connecting water supply hose gt Water supply pressure must be between 30kPa and 1000kPa 0 3 10kgficm gt Don t strip or crossthread when connecting Inlet hos
9. and other usage conditions If the imbalance is detected or if the suds removing program works the wash time shall be increased 27 Ti guide e Water supply is not adequate in area Check another tap in the house e Water supply taps are not completely open Fully open tap e Water inlet hose s are ee Straighten hose s e The filter of the inlet hose s are clogged Check the filter of the inlet hose e Drain hose is kinked or clogged Clean and straighten the drain hose e The drain filter is clogged Clean the drain filter e Load is too small Add 1 or 2 similar items to help e Load is out of balance balance the load e The appliance has an imbalance detection Rearrange load to allow proper and correction system If individual heavy spinning articles are loaded ex bath mat bath robe etc this system may stop spinning or even interrupt the spin cycle altogether lf the laundry is still too wet at the end of the cycle add smaller articles of laundry to balance the load and repeat the spin cycle F Close the door e Is the door opened If dE is not released call for service Unplug the power plug and call for service e Water overfills due to the faulty water valve Close the water tap Unplug the power plug Call for service e Water level sensor has malfunctioned e Over load in motor e Over load in motor The washer experienced a power failure Restart the cycle
10. e the power is turned off automatically after 4 minutes NB The door will not open before 1 to 2 minutes when Pause is selected or atthe end of the wash cycle Detecting e While the Detecting is shown in the display the machine rotates slowly and detects how many laundries are loaded in the drum It will take a few seconds e Available in Cotton Cotton Quick and Synthetic Door Lock Q e Lights whenever the door of the washer is locked The door can be unlocked by pressing the Start Pause button to stop the washer The door can be opened after a short delay Option By pressing the Option button all Option functions may be selected Medic Rinse Q Pre Wash Q Intensive Q Crease Care Q 1 Medic Rinse For high effectiveness or more purity in rinse operation you can choose Medic Rinse option It can be chosen in all course with the exception of Cotton Quick Quick 30 Hand Wash Wool Duvet Delicate and Bulky 2 Pre Wash If the laundry is heavily soiled Pre Wash course is effective e Pre Wash is available in Cotton Cotton Quick Synthetic Bio Care Baby Care and Boiling Care 3 Intensive If the laundry is heavily soiled Intensive option is effective By selecting the Intensive option the wash time may be extended depending on the program selected 4 Crease Care f you want to prevent crease select this button with spin s
11. e the risk that it might fall off X Diagonal Check When pushing down the edges of the washing machine top plate diagonally the machine should not move up and down at all Please check both of two directions If machine rocks when pushing the machine top plate diagonally adjust the feet again E Concrete floors e The installation surface must be clean dry and level e Install washer on a flat hard floor E Tile floors Slippery floors e Position each foot on the Tread Mate and level the machine to suit Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed X Tread Mate is a self adhesive material used on ladders amp steps that prevents slipping E Wooden floors Suspended floors A Rubber Cup e Wooden floors are particularly susceptible to vibration e To prevent vibration we recommend you place rubber cups under each foot at least 15mm thick under the washer secured to at least 2 floor beams with screws e If possible install the washer in one of the corners of the room where the floor is more stable X Insert the rubber cups to reduce vibration X You can obtain the rubber cups p no 4620ER4002B from the LG spares dept Important e Proper placement and levelling of the washer ensure long regular and reliable operation e The washer must be absolutely horizontal and stand firmly in position e t must not Seesaw across corners under load
12. e to the valve gt If the water supply pressure is more than 1000kPa a decompression device should be installed e Two rubber seals are supplied with the water inlet hoses They are used for preventing water leaks e Make sure the connection to taps is tight enough e Periodically check the condition of the hose and replace the hose if necessary Sealing washer e Make sure that there is no kink on the hose and that it is not crushed EKAL After completing connection if water leaks from the hose repeat the same steps Use the most conventional type of faucet for water supply In case the faucet is square or too big remove the spacing ring before inserting the faucet into the adaptor nstallation E Normal Tap without thread amp screw type inlet hose 1 Unscrew the fixing screw to 2 Push the connector up tillthe 3 Push the water supply hose attach the tap rubber packing is in tight contact vertically upwards so that the with the tap Then tighten the 4 rubber packing within in the screws hose can adhere completely to PA the tap and then tighten it by SAs dl Au kern ckis im screwing it to the right Ye SE Sn u Upper Fixing screw aQ a nn r Connecto Plate Water supply N hose E Normal Tap without thread amp one touch type inlet hose Single inlet models 1 Untighten the upper connector 2 Push the upper connector up till 3 Connect the water supply hose screw the r
13. ed malfunctioning partially disassembled or has missing or broken parts including a damaged cord or plug Before discarding an old machine unplug it Render the plug useless Cut off the cable directly behind the appliance to prevent misuse When a product was under water Please call service center The risk of electric shock and fire Do not push down the door excessively when washer door open This could topple over the washer SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This appliance must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance Do not use an adapter or otherwise defeat the grounding plug If you don t have the proper outlet consult an electrician WARNING Improper connection of the equipment grounding conductor can result in risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it does not fit the outlet have a proper outlet installed by a qualified electrician Power plug e f the supply cord
14. es 14 How to use washer uuueesssnnneesnnnneneennnnnnnnnnnnennnnnnnnnnnnnennnnennnn 15 Maintenance essen 22 Troubleshooting guide ccccccccceccceceeeeeeeeceeeeeeeeeeeeeeeeeeereererere 26 Terms of Warranty ccccccccccccccccecceccceeeeeeeceeeeeeeeeeeeeseeseeeeerrrregs 29 1 Jarnings A WARNING READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE For your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or loss of life IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the washer follow basic precautions including the following Before installation check exterior damages If it has do not install Do not install or store the washer where it will be exposed to the weather Do not tamper with controls Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user maintenance instructions or published user repair instructions that you understand and have the skills to carry out Keep the area underneath and around your appliances free of combustible materials such as lint paper rags chemicals etc e Close supervision is necessary if this appliance is used by or near children Do not allow children to play on with or inside this or any o
15. g of the drain hose will protect the floor from damage due to water leakage about 105 cm max 100 cm min 60 cm 4 4 Laundry tub about 100 cm about 145 cm gt ax 100cm in 60cm about 105 cm max 100 cm min 60 cm p lt 4 4 The drain hose should not be placed higher than 100 cm above the floor e Proper securing of the drain hose will protect the floor from damage due to water leakage When the drain hose is too long do not force back into the washer This will cause abnormal noise gga E Level adjustment 1 Adjusting the washing machine level properly prevents excessive noise and vibration Install the appliance on a solid and level floor surface preferably in a corner of the room 3 Timber or suspended type flooring may contribute to excessive vibration and unblance errors 2 lf the floor is uneven adjust the adjustable feet as required do not insert pieces of wood etc under the feet Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level use a spirit level X After the washer is level tighten the lock nuts up towards of the base of the washer All lock nuts must be tightened gt In the case that the washing machine is installed on a raised platform it must be securely fastened in order to eliminat
16. h or controls Drain Hose E Positioning Install the washer on a flat hard floor Make sure that air circulation around the washer is not impeded by carpets rug etc Never try to correct any unevenness in the floor with pieces of wood cardboard or similar materials under the washer If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove an insulating 85x60cm covered with aluminum foil on the side facing the cooker or stove must be inserted between the two appliance The washer must not be installed in rooms where the temperature can drop below 0 C Please ensure that when the washer is installed it is easily accessible for the engineer in the event of a breakdown e With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable and a clearance of approximately 20mm is left between the top of the washer and the underside of the work top m BS Plug Safety Details For U K User IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE This appliance must be earthed Green and Yellow Earth Ole Brown Live Blue Neutral Ol N Fuse OO Cord grip As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
17. he outside ofthe machine can be cleaned with warm water and a neutral non abrasive household detergent Immediately wipe off any spills Wipe with damp cloth Try not to hit surface with sharp objects IMPORTANT Do not use methylated spirits diluents or similar products 2 Interior Dry around the washer door opening flexible gasket and door glass Run washer through a complete cycle using hot water Repeat process if necessary RKA Remove hard water deposits using only cleaners labeled as washer safe E Cold condition lf the washer is stored in an area where freezing may occur or moved in freezing temperatures follow these instructions to prevent damage to the washer 1 Turn off water supply tap 2 Disconnect hoses from water supply and drain water from hoses 3 Plug electrical cord into a properly grounded electrical outlet 4 Add 1gallon 3 8L of nontoxic recreational vehicle RV antifreeze into an empty wash drum Close the door Ul Set spin cycle and let washer spin for 1minute to drain out all water Not all of the RV antifreeze will be expelled Unplug electrical power cord dry the drum interior and close the door Remove dispenser drawer drain and dry excessive water from the compartments Store washer in an uprignt position O oOo N Oo To remove antifreeze from washer after storage run empty washer through a complete cycle using detergent Do not add wash load 25 Ti guide Th
18. is damaged it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard Drawer For detergent and fabric softener SS Se Ss Control panel ID Sick J p Drum Door Drain pump filter Lower cover Drain plug Adjustable feet _ __ Lower cover cap E Name Front loading washing machine E Power supply 220 240V 50Hz E Size 600mm W x550mm D x 850mm H E Weight Max Watt 58kg 2100W E Wash capacity 8kg E Water consumption 56 2 7 2 kg E Permissible water pressure 0 3 10kgf cn 80 1000kPa E Spin speed No Spin 400 800 1400 F1422TD 1 9 No Spin 400 800 1200 F1222TD 1 9 No Spin 400 800 1000 F1022TD 1 9 x The appearance and specifications may be varied without notice to raise the units quality Accessories Inlet hose 1EA Spanner U aio Install or store where it will not be exposed to temperatures below freezing or exposed to the weather Properly ground washer to conform with all governing codes and ordinances The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor In countries where there are areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in clean condition at all times Any damage which may be cause by cockroaches or other vermin will
19. is washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all check the following points before you contact your service provider Rattling and e Foreign objects such as coins or Stop washer and check drum clanking noise Thumping sound Vibrating noise Water leaks Oversudsing Water does not enter washer or it enters slowly Water in the washer does not drain or drains slowly 26 Safety pins maybe in drum or pump e Heavy wash loads may produce a thumping sound This is usually normal e Have all the transit bolts and packing been removed Are all the feet resting firmly on the ground Fill hoses or drain hose are loose at tap or washer e House drain pipes are clogged e Water supply is not adequate in area e Water supply tap is not completely open e Water inlet hose s are kinked The filter of the inlet hose s clogged e Drain hose is kinked or clogged e The drain filter is clogged and drain filter If noise continues after washer is restarted call your authorised service centre If sound continues washer is probably out of balance Stop and redistribute wash load lf not removed during installation Refer to Installation guide for removing transit bolts Wash load may be unevenly distributed in dru
20. ive option for test in accordance or in conformity with EN60456 and IEC60456 Crease Care If you want to prevent crease select Crease Care button The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0708 WOOLMARK Notes Neutral detergent is recommended The wool cycle features gentle tumbling and low speed spin for garment care 14 Hi to use washer Baby Carey N Cotton Catton Quick MedicRinse peren ane son a N D Pre Wash J Duvet Boiling Care Bio Care Hand Wash Kuh Wool amp Intensive QO O 1400 O 95 C Bulky O 800 O60 O 400 040 e Quick 30 Crease Care QO J No Spin San O Rinse Hold O Cold N Rinse Spin Q Delicate e Spin VA Press amp Hold 3sec for S p in Tub Clean Function 1 Cotton automatically 2 Manual Selecting selected upon power on Press the Power button to start e Select the conditions which you want to use Press the Power button to start by turning the program dial and pressing e Press the Start Pause button each button Initial conditions For selecting the each conditions please refer to the pagel6 page21 Wash main wash Press the Start Pause button Rinse 3 times Spin
21. lance load Add one or two similar items Check all pockets to make sure that they are empty Items such as nails hair clip matches pens coins and keys can damage both your washer and your clothes e Close zippers hooks and strings to make sure that these items don t snag on other clothes Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt e Check the folds of the flexible gasket gray and remove any small articles if any e Check inside of the drum and remove any left items in it for next wash cycle e Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages 11 padding detergent E Adding detergent and fabric softener 1 The Dispenser Drawer Do PE Vo Detergent for Fabric Detergent for main wash softener pre wash u AB LLY 2 Adding Fabric Softener 12 e Main wash only gt UUI e Pre Wash Main Wash gt LL LL Do not exceed the maximum fill line Close the dispenser drawer slowly Overfilling can cause early dispensing of the fabric softener which could stain clothes Do not leave the fabric softener in the detergent drawer for more than 2 days Fabric softener could harden e Softener will automatically be added during the last rinse cycle e Do not open the drawer when water is supplied e Solvents benzene e
22. m Stop washer and rearrange wash load Check and tighten hose connections Unclog drain pipe Contact plumber if necessary Too much detergent or unsuitable detergent may cause excessive foaming which may result in water leaks Check another tap in the house Fully open tap Straighten hose Check the filter of the inlet hose Clean and straighten the drain hose Clean the drain filter T groubleshooting guide Washer does not start Electrical power cord may not be plugged in or connection may be loose House fuse blown circuit breaker tripped or a power outage has occurred e Water supply tap is not turned on Washer will not spin Check that the door is firmly shut Door does not open Wash cycle time delayed Make sure plug fits tightly in wall outlet Reset circuit breaker or replace fuse Do not increase fuse capacity If problem is a circuit overload have it corrected by a qualified electrician Turn on water supply tap Close the door and press the Start Pause button After pressing the Start Pause button it may take a few moments before the clothes washer begins to spin The door must lock before spin can be achieved Once started the door can not be opened for safety reasons Wait one or two minutes before opening the door to give the electric locking mechanism time to release The washing time may vary by the amount of laundry water pressure water temperature
23. not be covered by the appliance guarantee E Transit bolts The appliance is fitted with transit bolts to prevent internal damage during transport e Packing and all transit bolts must be removed before using the washer i When unpacking the base be sure to remove the additional packing support in the middle of the base packing Packing Support Packing support may not be used depending on models E Removing transit bolts 1 To prevent internal damage during 3 Take out the 4 bolts along with the transport the special 4 bolts are rubber bungs by slightly twisting the locked Before operating the washer bung Keep the 4 bolts and the remove spanner for future use the bolts along with the rubber bungs If they are not removed it may cause e Whenever the appliance is transported heavy vibration noise and malfunction the transit bolts must be refitted 2 Unscrew the 4 bolts with 4 Close the holes with the caps supplied the spanner supplied 2 Beten E Installation place requirement Level floor Allowable slope under entire washer is 1 Power outlet Must be within 1 5 meters of either side of location of washer Do not overload the outlet with more than one appliance Additional Clearance For wall door and floor modeling is required 10cm rear 2cm right amp left side Do not place or store laundry products on top of washer at any times They can damage the finis
24. peed The required lamp will light up for identification Lew to use washer Child Lock Medic Rinse Pre Wash C J Tub Clean Intensive Q 5 Crease Care OQ lf you choose to lock the buttons on the control assembly to prevent tampering this function may be selected e Child Lock can be set by pressing the Medic Rinse button and Pre Wash button simultaneously About three seconds Detecting Wash Rinse Spin Medic Rinse Pre Was To deactivate Child Lock system press Medic Rinse and Pre Wash buttons simultaneously again About three seconds Detecting Wash Rinse Spin Medic Rinse Pre Was To change to the desired program whilst in child lock mode 1 Press both Medic Rinse and Pre Wash together once again About three seconds 2 Press the Start Pause button 3 Select the desired program and press the Start Pause button again Medic Rinse Change L L gt the desired gt Pre Was J program The child lock can be set at any time and it can be deactivated only by using child lock cancel process Turning the power off and operational errors will not affect child lock 18 Tub Clean course can be set by pressing and holding Intensive and Pre Wash button simultaneously When Tub Clean course is set display teL and all buttons are inoperable TUB CLEAN is special cycle to clean the inside of the washer This cycle uses higher water le
25. rgents and fabric softeners leave a deposit in the drawer It should be cleaned from time to time with a jet of running water necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out To facilitate cleaning the upper part of the fabric softener compartment can be removed E The drawer recess 7 Detergent can also accumulate inside the recess which should be cleaned occasionally with an old toothbrush e Once you have finished cleaning replace the drawer and run a rinse cycle without laundry E The washing drum If you live in a hard water area limescale may continuously build up in places where it cannot be seen and thus not easily removed Over time the build up of scale clogs appliances and if it is not kept in check these may have to be replaced Although the washing drum is made of Stainless steel specks of rust can be caused by small metal articles paper clips safety pins which have been left in the drum The washing drum should be cleaned from time to time If you use descaling agents dyes or bleaches make sure they are suitable for washing machine use Descaler may contain chemicals that may damage part of your washing machine Remove any spots with a stainless steel cleaning agent Never use steel wool 24 y Jaintenance WE Cleaning your washer 1 Exterior Proper care of your washer can extend its life T
26. ssage will blink on the control panel when water does not enter the detergent drawer If water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time 1 Turn off the water tap 2 Unscrew the water inlet hose 3 Clean the filter using a hard bristle brush 4 Tighten up the inlet hose iy jaintenance E The drain pump filter The drain filter collects threads and small objects left in the laundry Check regularly that the filter is clean to ensure smooth running of your machine A CAUTION First drain using the drain hose and then open the pump filter to remove whatever any threads or objects Be careful when draining if the water is hot Allow the water to cool down before cleaning the drain pump carrying out emergency emptying or opening the door in an emergency 1 Open the lower cover cap D by using a coin Drain plug to pull out the hose 2 Unplug the drain plug allowing the water to flow out At this time use a vessel to prevent water flowing on to the floor When water does not flow any more turn the pump filter open to the left 3 Remove out any foreign material from the pump filter 4 After cleaning turn the pump filter clockwise and insert the drain plug to the original place close the lower cover cap J Mn E Dispenser drawer After a while dete
27. tc are not allowable RKA Do not pour fabric softener directly on the cloths padding detergent 3 Detergent dosage e The detergent should be used according to the instruction of the detergent manufacture If too much detergent is used too many suds can occur and this will decrease the washing result or cause heavy load to the motor e Use powder detergent only for the front loading washer Z X If suds occur too much pleas reduce the detergent amount e Detergent usage may need to be adjusted for water temperature water hardness size and soil level of the load For best results avoid oversudsing 4 Water softener A water softener such as Anti limescale Calgon can be used to cut down on the use of detergent in extremely hard water areas Dispense according to the amount specified on the packaging First add detergent and then the water softener e Use the quantity of detergent as for soft water Tips Full load according to manufacturer s recommendation Part load 3 4 of the normal amount Minimum load 1 2 of full load e Detergent is flushed from the dispenser at the beginning of the cycle 5 Using the Tablets 1 Open the door and Tablets into the drum 3 Close the door F unction E Recommended courses according to the laundry type Color fast garments shirts night dresses ce Medic Rinse Less than pajamas and lightly soiled white 40 C 95
28. tener in the drawer e How to set Time Delay Press Power button Turn the Program dial to select the program you require Press Time Delay button and set the desired time Press the Start Pause button blinks If Time Delay button is pressed 3 00 is displayed The maximum delayed time is 19 hours and the minimum time is 3 hours e Each pressing of the button advances on time delay by one hour To cancel the time delay press the Power button e Time Delay is expected time from the present to the completion of washing cycle or selected process Wash Rinse Spin e According to the condition of water supply and temperature the delayed time and the actual washing time may vary Lew to use washer Display 1 Special function display e When child lock is selected the u LL is displayed e When time delay is selected it shows the remaining time to finish the selected program 2 Self diagnosis display lf the machine encounters a fault during operation the associated fault will be displayed oon Water pressure sensing error FE Problem of overfilling water JE Door is not closed i Over load in motor LE Over load in motor 1 2 Water inlet trouble o u rit Drainage trouble Le 66 1 Lie 6 D im 7 Unbalanced load Water temperature trouble The washer experienced a power failure
29. the terminals in your plug proceed as follows The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol S or coloured Green or Green and Yellow The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red Ita 13 amp BS 1363 plug is used fit a 13 amp BS 1362 fuse 6 nstallation E Electrical connection 1 Do not use an extension cord or double adapter 2 If the supply cord is damaged it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard 3 Always unplug the machine and turn off the water supply after use 4 Connect the machine to an earthed socket in accordance with current wiring regulations 5 The appliance must be positioned so that the plug is easily accessible e Repairs to the washing machine must only be carried out by qualified personnel Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local service center Do not install your washing machine in rooms where temperature below freezing may occur Frozen hoses may burst under pressure The reliability of the electronic control unit may be impaired at temperatures below freezing point
30. ther appliance e Keep small animals away from the appliance Do not leave the washer door open An open door could entice children to hang on the door or crawl inside the washer e Never reach into washer while it is moving Wait until the drum has completely stopped The laundry process can reduce the flame retardant of fabrics To avoid such a result carefully follow the garment manufacturer s wash and care instructions Do not wash or dry articles that have been cleaned in washed in soaked in or spotted with combustible or explosive substances such as wax oil paint gasoline degreasers dry cleaning solvents kerosene etc which may ignite or explode Oil may remain in the tub after a whole cycle resulting in fire during drying So do not load oiled clothes Do not slam the washer door closed or try to force the door open when locked This could result in damage to the washer e When the machine runs high temperature the front door may be very hot Don t touch it e To minimize the possibility of electric shock unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning e When unplugging power cord do not pull out by grasping the cord Otherwise the power cord may be damaged Never attempt to operate this appliance if it is damag
31. tton Quick Rinse Spin Quick 30 Bio Care Bulky Spin Rinse Hold No Spin 400 800 1200 Delicate Duvet Baby Care Boiling Care Synthetic Hand Wash Wool Rinse Hold No Spin 400 800 F1022TD 1 9 Cotton Cotton Quick Rinse Spin Quick 30 Bio Care Bulky Spin Rinse Hold No Spin 400 800 1000 Delicate Duvet Baby Care Boiling Care Synthetic Hand Wash Wool Rinse Hold No Spin 400 800 2 No spin e If No spin is selected the washer stops after draining water 3 Rinse Hold e Rinse Hold is selected by pressing the spin button repeatedly this function leaves clothes in the machine Suspended in the water after a rinse without entering into spin To proceed through to a drain or spin once the rinse hold function is completed using to Program dial and Spin button to the required program Spin The required lamp will light up for identification 19 Hi to use washer Water Temp e By pressing the Temp button the water temperature can be selected Cold 30 C 40 C 60 C 1 95 C e Water temperature can be selected according to the program The required temperature lamp will light up for identification For the more detailed information please refer to the pagel4 20 Time Delay Preparing washing before starting Time Delay Turn on the water tap Load laundry and close the door Place the detergent and fabric sof
32. ubber packing is in tight to the middle connector contact with the tap Then pushing the plate down Rubber tighten the 4 screws Middle connector In case the diameter of the tap is large remove the guide plate plate amp Turn the middle connector not To separate the water supply to have water leaked hose from the middle connector shut off the tap Then pull the inlet hose down pushing the plate down e Make sure that the rubber seal is inside the hose connector Used the horizontal tap Horizontal tap EX e Make sure that there are no kinks in the hose and that it is Extension tap FR 4 not crushed Square tap Sn U ii This equipment is not designed for maritime use or for use mobile installations such as caravans aircraft etc Turn off the stopcock if the machine is to be left for any length of time e g holiday especially if there is no floor drain gully in the immediate vicinity When disposing of the appliance cut off the mains cable and destroy the plug Disable the door lock to prevent young children being trapped inside Packaging material e g Films Styrofoam can be dangerous for children There is a risk of suffocation Keep all packaging well away from children E Installation of drain hose about 100 cm gt e When installing the drain hose sink secure it tightly with a string e Proper securin
33. vel with higher spin speed Perform this cycle regularly How to use the Tub Clean cycle 1 Remove any clothing or items from the washer and close the door 2 Open the dispenser drawer and add Anti limescale Calgon to the Main wash compartment NOTE Do not add any detergent to the detergent compartments Excessive suds may generate and leak from the washer Close the dispenser drawer slowly Power On and then press and hold Intensive and Pre Wash button for 3 seconds then ici is displayed in LED 5 Press the Start Pause button to start After the cycle is complete leave the door open to dry around the washer door opening flexible gasket and door glass A O O A CAUTION If there is a small child be careful not to leave the door open for too long Hi to use washer Spin After selecting the spin course the O 1400 O 1200 O 800 O 800 400 O 400 O No Spin O Rinse Hold O 1000 O 800 spin speed can be chosen by O 400 pressing the spin button O No Spin O Rinse Hold O No Spin O Rinse Hold F1422TD 1 9 F1222TD 1 9 F1022TD 1 9 1 Spin selection e Spin Speed is available according to the program as follows F1422TD 1 9 Cotton Cotton Quick Rinse Spin Quick 30 Bio Care Bulky Spin Rinse Hold No Spin 400 800 1400 Delicate Duvet Baby Care Boiling Care Synthetic Hand Wash Wool Rinse Hold No Spin 400 800 F1222TD 1 9 Cotton Co
34. wner s manual e Removal of foreign objects substances from the machine including the pump and inlet hose filter for example grit nails bra wires buttons etc e Replace fuses in or correct house wiring or correct house plumbing e Correction of unauthorized repairs Incidental or consequential damage to personal property caused by possible defects with this appliance If this product is used for commercial purpose it is not warranted Example Public places such as public bathroom lodging house training center dormitory If the product is installed outside the normal service area any cost of transportation involved in the repair of the product or the replacement of a defective part shall be borne by the owner 29 30 For U K Customer CUSTOMER SERVICES Tel 0870 873 LGLG 5454 Fax 0870 872 7337 LGEUK SERVICE WEB SITE http uk lge com P No MFL49491523
Download Pdf Manuals
Related Search