Zanussi ZKG7145 washer dryer
Contents
1. Connect the other end of the inlet hose to the back of the appliance The inlet hose can be turned as showed in the picture Do not place the inlet hose down wards Angle the hose to the left or right depending on the position of your water tap Set the hose correctly by loosening the ring nut After positioning the inlet hose be sure to tighten the ring nut again to prevent leaks Caution The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use Warning Installation should comply with local water authority and building regulations requirements The appliance must be connected to a cold water supply A minimum water pressure of 0 05 MPa 0 5 bar is required for safe operation of the appliance If you cannot make the cold water connection direct from the rising mains you may be able to operate the appliance from your cold water storage system 28 There should be a minimum vertical distance of 5 02 m 16 5 ft between the appliance s inlet and the bottom of the water storage tank Water drainage This appliance is designed to be permanently plumbed into your home s drainage system us ing one of the following methods 1 Into a drainage standpipe Firstly form a hook in the end of the drain hose using the U piece supplied U piece supplied P2. Tie any belts or long tapes Remove persistent stains before washing 12 Rub particularly soiled areas with a special de tergent or detergent paste Treat curtains with special care Remove hooks or tie them up in a bag or net Removing stains Stubborn stains may not be removed by just water and detergent It is therefore advisable to treat them prior to washing Blood treat fresh stains with cold water For dried stains soak overnight in water with a spe cial detergent then rub in the soap and water Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times www zanussi com Dried grease stains moisten with turpentine lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth Rust oxalic acid dissolved in hot water or a rust removing product used cold Be careful with rust stains which are not recent since the cellulose structure will already have been dam aged and the fabric tends to hole Mould stains treat with bleach rinse well whites and fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with ace tone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Treat any re sidual marks with bleach Red wine soak in water and detergent rinse and
3. User manual Washer Dryer U F R MANUAL ZKG 7125 ZKG 7145 ZANUSSI ZKG 7165 Contents Safety information 2 Personalisation 15 Safety instructions ______________ 3 Daily Use __________________ 15 Product description _ _ 5 Use Drying __ 2 _________ 17 Control panel _ 6 Care and cleaning _ ___________ 19 Washing Programmes __ 9 What to do if 22 Automatic Drying programmes _______ 11 Technicaldata_ 25 Drying Programmes __ ____________ 12 Consumption values 26 Helpful hints and tips 12 Installation 2 ____ 26 Drying Hints 2222 14 Environment concerns ___________ 29 First use 14 Subject to change without notice Safety information Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an in correct installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety A Warning Risk of suffocation injury or permanent disability Do not let persons children included with reduced physical sen sory reduced mental functions or lack of experience and knowl edge use the appliance They must have supervision or instruction for the operation of the appliance by a person who is responsible for their safety Do not let children play with the appliance Keep all packaging away from children Keep all detergent
4. different options can be combined These must be selected after choosing the desired programme and before starting the programme When these buttons are pressed the corresponding pilot lights illu minate When they are pressed again the pilot lights go out If an incorrect option is selected the integrated red pilot light of the button 7 flashes 3 times and the message Err is dis played For the compatibility among the washing pro grammes and the options see chapter Wash ing programmes 16 Start the programme by pressing button 7 To start the selected programme press this button the corresponding green pilot light stops blinking The pilot light 9 illuminates to indicate that the appliance starts operating and the door is locked If you have chosen a delayed start the machine will begin the countdown Important If an incorrect option is selected the message Err is displayed for a few seconds and the red pilot light of this button blinks 3 times Select the Delay Start by pressing button 8 Before you start the programme if you wish to delay the start press this button to select the desired delay The selected delay time value will appear on the display for a few seconds then the duration of the programme will appear again You must select this option after you have set the programme and before you start the pro gramme You can cancel or modify the delay time at any moment before you press butt
5. the display see the Drying Programmes table Every time you press this button the drying time increases by 5 minutes Note The programme time will automatically in crease by a few minutes 6 Press button 7 to start the programme After the programme has started the time remaining is updated every minute Note The different type of cottons towelling sheets shirts and so on or any laundry items rolling up during the spinning phase may result in partial dryness In the excep tional case that at the end of the cycle the laundry remains slightly wet we suggest that you unfold the rolled up items redis tribute them evenly in the drum and select an additional drying cycle of 20 30 mi nutes 7 At the end of the programme the buzzer sounds and a blinking appear on the display The last 10 minutes of the drying cycle correspond to an anti crease phase Dur ing this time the door is locked and the dis play keeps showing the flashing zero Note 18 If you wish to open the door before or dur ing the anti crease phase or to interrupt it press any button or turn the programme selector dial to any programme position except the door can be opened after a few minutes 8 Turn the selector dial to the C position to switch the machine off 9 Remove the laundry i Automatic washing and drying NON STOP programme For NON STOP programmes the recommen ded load size is 3 kg for co
6. Cottons and Synthetics ron dry Cottons The pilot light corresponding to the selected dryness degree will illuminate Drying Time If you wish to carry out a timed drying pro gramme press this button until the drying time you want appears on the display according to the fabrics cottons or synthetics you have to dry For Cottons you can select a drying time from 10 minutes to 250 minutes 4 10 For Synthetics you can select a drying time from 10 minutes to 130 minutes 2 10 Every time you press this button the drying time increases by 5 mins www zanussi com E Door pilot light Display Child Safety Lock Available options Super Quick Short cycle for lightly soiled items or for laundry which needs only freshening up We recom mend you to reduce the fabrics loading Extra Rinse This appliance is designed to save energy If it necessary to rinse the laundry using an extra quantity of water extra rinse select this option Some additional rinses will be performed This option is recommended for people who are al lergic to detergents and in areas where the water is very soft Start Pause This button allows you to start or to interrupt the selected programme Delay Start The programme can be delayed from 30 min 60 min 90 min 2 hours and then by 1 hour up to a maximum of 20 hours by means of this but ton Door light The pilot light 9 illuminates when the pro gramme starts and indicate
7. There is water in the drum Select drain or spin programme to empty out the water The transit bolts and packing have not been removed Check the correct installation of the appliance The support feet have not been adjusted Check the correct levelling of the appliance The laundry is not evenly distributed in the drum Redistribute the laundry Maybe there is very little laundry in the drum Load more laundry The electronic unbalance detection device has cut in because the laun dry is not evenly distributed in the drum The laundry is redistributed by reverse rotation of the drum This may happen several times before the unbalance disappears and normal spinning can resume If after 10 mi nutes the laundry is still not evenly distributed in the drum the machine will not spin In this case redistribute the load manually and select the spin programme Redistribute the laundry The load is too small Add more items redistribute the load manually and then select the spinning programme www zanussi com The machine is fitted with a type of motor which makes an unusual noise The machine makes an un compared with other traditional motors This new motor ensures a softer usual noise start and more even distribution of the laundry in the drum when spin ning as well as increased stability of the machine No water is visible in the Machines based on modern technology operate very economically using drum ver
8. and pull forward the drainage duct to let the water flow out 20 When the container is full of water put the drainage duct back again and empty the con tainer Do steps 3 and 4 again and again until no more water flows out from the drain pump Pull back the drainage duct Unscrew the filter and remove it Remove fluff and objects from the pump ES Make sure that the impeller of the pump can turn If this does not occur contact the serv ice centre www zanussi com Turn off the water tap Unscrew the hose from the tap Clean the filter in the hose with a stiff brush Clean the filter under the water tap and put it back in the pump into the special guides Make sure that you tighten correctly the filter to prevent leakages Close the pump door Caution When the appliance is in use and depending on the programme selected there can be hot water in the pump Never remove the pump cover during a wash cycle always wait until the appliance has finished the cycle and is empty When refitting the pump cover ensure it is securely re tightened so as to stop leaks and young children being able to remove it Cleaning the water inlet filters Important If the appliance doesn t fill takes long to fill with water the starting button blinks yellow or the display if available shows the relevant alarm see chapter What to do if for more detai
9. cooking oil acetone alcohol petrol kerosene spot re movers turpentine waxes and wax removers wash them in hot water with an extra amount of detergent Do not dry items if industrial chemicals have been used for cleaning Make sure that no gas lighters or matches have been left in the pockets of the clothing Only dry fabrics which are applicable to dry in the tumble dryer Follow the instructions on the fabric label Do not dry not washed items in the appli ance If you have washed your laundry with a stain remover start an extra rinse cycle before you start the appliance Plastic items are not heat resistant If you use a detergent ball remove it be fore you set the drying programme Do not use a detergent ball when you set a non stop programme Warning Risk of injury or damage to the appliance Do not sit or stand on the open door Obey the maximum load volume Do not dry dripping wet clothes in the appli ance Care and Cleaning Warning Risk of injury or damage to the appliance Do not use water spray and steam to clean the appliance Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal objects Disposal www zanussi com A Warning Risk of injury or suffocation Service Contact the Service to repair the appliance Disconnect the appliance from the mains de
10. draining Follow the below instructions to empty out the water 1 Turn the programme selector dial to 2 Select the draining or spinning programme 3 Reduce the spin speed if needed by pressing the relevant button 4 Press button 7 At the end of the programme the door is re leased and can be opened Turn the pro gramme selector dial to to switch the ma chine off Remove the laundry from the drum and carefully check that the drum is empty If you do not in tend to carry out another wash close the water tap Leave the door open to prevent the forma tion of mildew and unpleasant smells The recommended load size is 3 kg for cottons and linen and 2 kg for synthetic items 17 Note By pressing Drying Time button it is also possible to dry up to 4 kg of cotton items see the Drying Programme table The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe 1 Load the laundry 2 Select a spin cycle at the maximum spin speed allowed for the type of laundry in or der to obtain the best drying performances 3 Select the drying programme for Cottons or Synthetic in the Drying sector of the programme selector dial 4 If you wish to select an electronic drying press the button 3 until the pilot light cor responding to the required dryness degree illuminates 5 If you wish to select a timed drying press button 4 until the time you want appears on
11. fabric as sponge cloth sweatshirt could release fluff The released fluff could stick to the fabrics dur ing the next cycle This drawback increases with technical fabrics To prevent the lint in your clothes it is recom mended To do not wash dark fabrics after you wash ed and dried light coloured fabrics new Care and cleaning A Warning You must DISCONNECT the appliance from the electricity supply before you can carry out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the soft ening powder manufacturer s instructions This will help to prevent the formation of lime depos its External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thoroughly Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly www zanussi com anti crease phase please follow the in structions given in the previous chapter 8 Turn the selector dial to the position to switch the machine off 9 Remove the laundry sponge sweatshirt especially and vice ver sa To air dry this type of fabrics when they are washed the first time To clean the filter Perform one or more rinse cycles to wash the drum between the washing and drying of fa
12. is less than 0 C or where it is Do not use multi plug adapters and exten exposed to the weather PES ec f sion cables Obey the installation instruction supplied Make sure not to cause damage to the mains with the appliance plug and to the mains cable Should the ap Make sure that the floor where you install the pliance power supply cable need to be re appliance is flat stable heat resistant and placed this must be carried out by our Serv clean ice Centre Do not install the appliance where the appli Connect the mains plug to the mains socket ance door can not be fully opened only at the end of the installation Make sure Always be careful when you move the appli that there is access to the mains plug after ance because it is heavy Always wear safety the installation gloves Do not pull the mains cable to disconnect Make sure that there is air circulation be the appliance Always pull the mains plug tween the appliance and the floor Do not touch the mains cable or the mains Adjust the feet to have the necessary space plug with wet hands between the appliance and the carpet Only for UK and Ireland The appliance has a Electrical connection 13 amp mains plug If it is necessary to www zanussi com change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse This appliance complies with the E E C Di rectives Water connection Make sure not to cause damage to the wa
13. not been closed F4Y Close the door firmly The plug is not properly inserted in the power socket Insert the plug into the power socket There is no power at the socket Please check your domestic electrical installation The washing machine does Tine mein tse hes lonn not start Replace the fuse The selector dial is not correctly positioned and or the button 7 has not been pressed Please turn the selector dial and press the button 7 again The delay start has been selected If the laundry are to be washed immediately cancel the delay start The Child Safety Lock has been activated Deactivate the Child Safety Lock The water tap is closed Fig Open the water tap The inlet hose is squashed or kinked E107 Check the inlet hose connection The machine does not fill The filter in the inlet hose or in the inlet valve filter are blocked E Clean the water inlet filters see Cleaning the water inlet filters for more details The door is not properly closed EY fF Close the door firmly The machine fills then emp The end of the drain hose is too low ties immediately Refer to relevant paragraph in Water drainage section The drain hose is squashed or kinked Feu Check the drain hose connection The drain filter is clogged Ef The machine does not empty Clean the drain filter re and or does not spin An option or a programme that ends with the water still in the tub o
14. s bpl We recommend only the use of original pply spare parts Cut off the mains cable and discard it Remove the door catch to prevent children and pets to get closed in the appliance Product description Detergent dispenser drawer Control panel Door opening handle Rating plate Drain pump g Adjustable feet Detergent dispenser drawer UJ Compartment for detergent used for pre UJ wash and soak phase or for stain remover used during the stain action phase if available The D prewash and soak detergent is added at the be A AID BE Ez Z ginning of the wash programme The stain re mover is added during the stain action phase UY Compartment for powder or liquid detergent used for main wash If using liquid detergent pour it just before starting the programme www zanussi com Compartment for liquid additives fabric softener starch Follow the product manufacturer s recommendations on quantities to use and do not exceed the MAX mark in the detergent dispenser drawer Any fabric softener or starching additives must be poured into the compartment before starting the wash programme Child Safety device Make sure that children or pets do not climb in to the drum To prevent children and pets be M Yj coming trapped inside the drum this machine incorporates a special feature el To activate this de vice rotate the button without pressing it inside the door clock wise until the
15. the selected programme option it requires see more details in Detergent dispenser drawer If required pour fabric softener into the com partment marked amp the amount used must not exceed the MAX mark in the drawer Close the drawer gently 15 Select the required programme by means of the programme selector dial 1 Turn the programme selector dial to the re quired programme The green pilot light of button 7 starts to flash The selector dial can be turned either clockwise or anticlockwise Turn the selector dial to position C to reset the programme to switch the machine OFF At the end of the programme the selector dial must be turned to position O to switch the machine off Important If you turn the programme selector dial to another programme when the machine is working the red pilot light of button 7 will blink 3 times and the messageErr is displayed to indicate a wrong selection The machine will not perform the new selected programme Select the spin speed by pressing button 2 When selecting a programme the appliance proposes automatically the maximum spin speed provided for that programme See Washing programmes for the maximum al lowed spin speed Press this button repeatedly to change the spin speed if you want your laundry to be spun at a different speed The relevant pilot light illumi nates Select the available options by pressing the buttons 5 and 6 Depending on the programme
16. to do if Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Centre please carry out the checks listed below During machine operation it is possible that the red pilot light of button 7 blinks one of the fol lowing alarm codes appears on the display and some acoustic signals sound every 20 seconds to indicate that the machine is not working 22 4 open the pump door 5 place a container on the floor below the re cess of the drain pump 6 press the two levers and pull forward the drainage duct to let the water flow out 7 when the container is full of water put the drainage duct back again and empty the container repeat this operation until water stops flowing out 8 if necessary clean the pump refer to the section Cleaning the pump 9 close the drain pump door When you drain the water with the emergency drain procedure you must activate again the drain system 1 Put 2 litres of water in the main wash com partment of the detergent dispenser 2 Start the programme to drain the water EJL problem with the water supply 20 problem with the water draining EU door open Once the problem has been eliminated press the button 7 to restart the programme If after all checks the problem persists contact your local Service Centre www zanussi com The door has
17. woollens and delicate fabrics Note A single or bulky item may cause imbalance If the appli ance doesn t perform the final spin phase add more items redistribute the load manually and then select the spinning programme Jeans 40 Main wash Rinses Maximum spin speed at 1200 rpm Max load 3 kg With this programme it is possible to wash items like pants shirts or jackets in denim tissue and also jersey real ized with hi tech materials Note The Extra Rinse option will be activated automatically Sport Intensive 40 Prewash Main wash Rinses Maximum spin speed at 900 rom Max load 2 5 kg This programme is suitable for washing heavily soiled sport items The appliance will add automatically a prewash phase before the main wash to eliminate mud stains 10 SPIN RINSE HOLD EXTRA RINSE SPIN RINSE HOLD SUPER QUICK EXTRA RINSE SPIN RINSE HOLD SPIN RINSE HOLD SPIN RINSE HOLD E E E E www zanussi com Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maxi Detergent Com mum Fabrics Load Type of Laundry cae Rinses SPIN amp Maximum spin speed at 1200 rpm ZKG 7125 1400 rpm RINSE HOLD ZKG 7145 1600 rpm ZKG 7165 EXTRA RINSE Max load 6 kg With this programme it is possible to rinse and spin cotton garments which have been washed by hand The machine performs 3 rinses followed by a final long spin Important The spin
18. brics with different colours After the drying phase thoroughly clean the empty drum the gasket and the door with a wet rag Remove the drawer by pressing the catch downwards and by pulling it out Flush it out under a tap to re move any traces of accumulated powder To aid cleaning the top part of the addi tive compartment should be removed Cleaning the drawer recess Having removed the drawer use a small brush to clean the re cess ensuring that all washing powder resi due is removed from the upper and lower part of the recess 19 Replace the drawer and run the rinse pro gramme without any clothes in the drum Cleaning the pump The pump should be inspected regularly and particularly if the appliance does not empty and or spin the appliance makes an unusual noise during draining due to objects such as safety pins coins etc blocking the pump a problem with water draining is detected see chapter What to do if for more de tails A Warning 1 Disconnect the mains plug from the mains socket 2 Do not remove the filter while the appliance operates Do not clean the drain pump if the water in the appliance is hot The water must be cold before you clean the drain pump Proceed as follows Open the pump door Put a container below the recess of the drain pump to collect the water that flows out ay x a Press the two levers
19. ceed the MAX mark in the detergent dispenser drawer Garment labels For drying follow the indications given on the manufacturer s labels May be tumble dried A Drying at high temperature i Drying at reduced temperature Do not tumble dry Drying cycle duration The drying time may vary depending on speed of the final spin dryness degree required iron dry store dry type of laundry weight of the load size The average drying time for a timed drying are indicated in the Drying programmes chapter The experience will help you to dry your laundry in a more suitable way according to the differ ent fabrics Take note of the duration drying time of the already performed cycles Additional drying If the laundry is still damp at the end of the dry ing programme select a short drying cycle again Warning Do not over dry the laundry in order to avoid creasing of fabrics or garment s shrinking Remove the polystyrene block and any material from the drum Before the first wash run a cotton cycle at the highest temperature without any www zanussi com laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of deter Personalisation Acoustic signals The machine is provided with an acoustic de vice which sounds in the following cases at the end of the cycle if there is a fault By pressing the 3 and 4 buttons simu
20. groove is horizontal If neces sary use a coin To disable this de vice and restore the possibility of closing the door rotate the button anti clockwise until the groove is vertical Control panel On the following page there is a picture of the control panel It shows the programme selector dial as well as the buttons pilot lights and the display These are presented by relevant num bers on the following pages A i o _ g oO A O oO O O UA O Programme selector dial Spin button Automatic drying button Drying time button Super quick button 6 Extra rinse button 6 www zanussi com Start Pause button E Delay start button Table of symbols Rinse hold Oo 1 8 Programme selector dial spin speed button drying level and time and available options Programme Selector Dial It allows you to switch the appliance on off and or to select a programme Spin By pressing this button you can change the spin speed of the selected programme or to se lect Rinse Hold option Rinse hold By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing Before opening the door it will be necessary to empty out the water To empty out the water please read the paragraph At the end of the programme Automatic Dry By pressing this button you can choose the re quired degree of drying for cottons and syn thetics Cupboard dry
21. h is not compatible with the set wash programme is selected the message Err is displayed at the bottom of the display for a few seconds and the integrated red light of button 7 start flashing End of programme When the programme has finished the flashing zero 0 is displayed the pilot light 9 and the pilot light of button 7 go out and the door can be opened www zanussi com Washing Programmes Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maxi mum Fabrics Load Type of Laundry Cottons 90 60 Main wash Rinses Maximum spin speed at 1200 rpm ZKG 7125 1400 rpm ZKG 7145 1600 rpm ZKG 7165 Max load 6 kg Reduced load 3 kg White cotton heavily and normally soiled items Cottons Eco 60 40 Main wash Rinses Maximum spin speed at 1200 rpm ZKG 7125 1400 rpm ZKG 7145 1600 rpm ZKG 7165 Max load 6 kg White or fast colour cotton normally soiled items This programme can be selected for normally soiled cotton items The temperature will decrease and the washing time will be extended This allows to obtain a good washing effi ciency by saving energy Cottons 60 30 Main wash Rinses Maximum spin speed at 1200 rpm ZKG 7125 1400 rpm ZKG 7145 1600 rpm ZKG 7165 Max load 6 kg Reduced load 3 kg White or colour cotton normally or slightly soiled items Cottons Prewash 60 40 Prewash Main wash Rinses Maxim
22. hat they can be recycled by dis posing of them properly in appropriate collec tion containers Ecological hints To save water energy and to help protect the environment we recommend that you follow these tips 30 Normally soiled laundry may be washed with out prewashing in order to save detergent water and time the environment is protected tool The machine works more economically if it is fully loaded With adequate pre treatment stains and limi ted soiling can be removed the laundry can then be washed at a lower temperature Measure out detergent according to the wa ter hardness the degree of soiling and the quantity of laundry being washed www zanussi com www zanussi com 31 www zanussi com shop ey kes NX MN 132937921 A 432012
23. he button 7 to interrupt a programme which is running the corresponding pilot light starts blinking Press the button again to re start the programme Cancelling a programme Turn the selector dial to to cancel a pro gramme which is running Now you can select a new programme Opening the door after the programme has started First set the machine to pause by pressing the button 7 If the pilot light 9 goes off the door can be opened Use Drying i Drying only www zanussi com If the pilot light 9 remains lit this means that the machine is already heating or that the water lev el is too high In any case do not force the door If you cannot open the door but you need to open it switch the machine off by turning the selector dial to After a few minutes the door can be opened Pay attention to the water level and tem perature After closing the door it is necessary to select the programme and options again and to press button 7 At the end of the programme The machine stops automatically The blinking J appears on the display the pilot light of but ton 7 and the pilot light 9 go off If a programme or an option that ends with wa ter left in the tub has been selected the pilot light 9 remains on and the door is locked to in dicate that the water must be emptied out be fore opening the door Before you empty out the water the drum con tinues to run at regular intervals until the water
24. l data Dimensions Width 60 cm Height 85 cm Depth 63 cm www zanussi com 25 Electrical connection Voltage Overall power Fuse Information on the electrical connection is given on the rating plate on the inner edge of the appliance door Water Supply Pressure Minimum 0 05 MPa Maximum 0 8 MPa Maximum Load Cotton 6 kg Maximum Dry Load Cotton 3 Kg Cotton Big Capacity 4 Kg Synthetic 2Kg Spin Speed Maximum 1600 rpm ZKG 7165 Consumption values 1400 rpm ZKG 7145 1200 rpm ZKG 7125 Programme Energy consumption Water consumption Programme duration CT lh Minutes Cottons 60 1 30 Cotton Energy Saving 1 02 Programme 60 1 Cottons 40 0 70 Synthetics 40 0 50 Delicates 40 0 55 Wool Handwash 30 0 25 For the duration of the programmes 46 please refer to the display on the control 58 panel 50 60 53 1 Cotton Energy Saving programme at 60 C with a load of 6 kg is the reference programme for the data entered in the energy label in compliance with EEC 92 75 standards The consumption data shown on this chart is to be considered purely indicative as it may vary depending on the quantity and type of laundry on the inlet water temperature and on the am bient temperature Installation Rubber feet kit 4055126249 Available from your authorized dealer The rubber feet are particularly recommended on floating slippery and wooden floors Mount the rubber feet to prevent vibratio
25. lace the drain hose into your standpipe which should have an internal diameter of ap proximately 38 mm thus ensuring there is an air break between the drain hose and stand pipe When discharging into a standpipe ensure that the top of the standpipe is no more than 90 cm 35 4 and no less than 60 cm 23 6 above floor level 38 mm 1 5 g standpipe 30 cm 12 The drain hose may be extended to a maxi mum of 4 metres An additional drain hose and joining piece is available from your local Service Force Centre The joining piece must have an internal diameter of 18 mm www zanussi com LL Min 60 cm 23 6 Max 90 cm 35 4 If your drain hose ooks like this see beside you do not require the U piece Just push the hose firmly in to the standpipe 2 Onto a sink outlet spigot Push the drain hose onto the spigot and secure with a clip ensure a loop is formed in the drain hose see above to prevent waste from the sink entering the appliance If the outlet spigot has not been used before remove any blanking plug that may be in place Environment concerns K The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this
26. loths shirts etc g www zanussi com 11 Drying Programmes Degree of Drying Suitable for items to put away without ironing els etc Suitable for items to put away without ironing Cotton and linen sheets tablecloths Suitable for ironing shirts etc Type of Fabric Cotton and linen bathrobes bath tow Synthetics and mixed fabrics Suggested drying time L EPARET Spin Speed in Mins 130 150 75 85 35 45 140 160 80 90 40 50 150 170 85 95 45 65 70 80 35 45 100 120 65 75 30 40 110 130 65 75 35 45 120 140 70 80 40 50 1600 4kg 3 kg 1 5 kg 1400 1200 2kg 1 kg 900 1600 4kg 3 kg 1 5 kg 1400 1200 In compliance with EC directive EN 50229 the cotton reference programme for the data entered in the Energy Label must be tested dividing the maximum washing load by two equal parts and drying with DRYING TIME each of them Helpful hints and tips Sorting out the laundry Follow the wash code symbols on each gar ment label and the manufacturer s washing in structions Sort the laundry as follows whites coloureds synthetics delicates woollens Before loading the laundry Never wash whites and coloureds together Whites may lose their whiteness in the wash New coloured items may run in the first wash they should therefore be washed separately the first time Button up pillowcases close zip fasteners hooks and poppers
27. ls check if the water inlet filters are blocked To clean the water inlet filters www zanussi com Screw the hose back onto the tap Make sure the connection is tight Unscrew the hose from the machine Keep a rag nearby because some water may flow Clean the filter in the valve with a stiff brush or with the piece of cloth Screw the hose back to the machine and make sure the connection is tight Turn on the water tap Frost precautions If the machine is installed in a place where the temperature could drop below 0 C remove the remaining water from the inlet hose and the drain pump 1 disconnect the mains plug from the mains socket 2 close the water tap 3 unscrew the water inlet hose from the tap 21 4 put the two ends of the inlet hose in a con tainer and let the water flow out of the hose 5 empty the drain pump as described in the Emergency emptying out section 6 when the drain pump is empty install the water inlet hose again A Warning Make sure that the temperature is more than O C before you use the appliance again The manufacturer is not responsible for dam ages caused by low temperatures Emergency emptying out If the appliance cannot drain the water pro ceed as follows to empty out the machine 1 pull out the plug from the power socket 2 close the water tap 3 if necessary wait until the water has cooled down What
28. ltaneously for about 6 seconds the acoustic signal is de activated except if there is a fault By pressing these 2 buttons again the acoustic signal is re activated Child safety lock This device permits you to leave the appliance unattended so you do not need to worry that Daily Use Load the laundry Open the door by carefully pulling the door handle out wards Place the laundry in the drum one item at a time shaking them out as much as possible Close the door Make sure that no laundry stays be tween the seal and the door There is a risk of water leakage or damage to the laundry www zanussi com gent into the main wash compartment and start the machine children might be injured by or cause damage to the appliance This function remains enabled also when the washing machine is not working There are two different ways to set this option 1 Before pressing button 7 it will be impos sible to start the machine 2 After pressing button 7 it will be impossi ble to change any other programme or op tion To enable or disable this option press simulta neously for about 6 seconds buttons 2 and 3 until on the display the icon FA appears or dis appears Measure out the detergent and the fabric softener Pull out the dispenser drawer until it stops Measure out the amount of detergent re quired pour it into the main wash compart ment Il or in the appropriate compartment if
29. n noises and displacement of the appliance dur ing operation Read carefully the instructions supplied with the kit Fixing plate kit 4055171146 Available from your authorized dealer 26 If you install the appliance on a plinth secure the appliance in the fixing plates Follow the instructions supplied with the kit Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again www zanussi com Remove the power supply cable and the hose from the hose holders on the rear of the appliance After removing all the packaging carefully ay machine on it s back to remove the polystyrene base from the bottom Slide out the relevant plastic spacers Unscrew the three bolts iis Open the porthole remove the polystyr ene block fitted on the door seal and pull out all items from the Fill the smaller upper hole and the two arge ones with the corresponding plastic plug caps supplied in drum the bag containing the instruction book let Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Level the washing machine by Www zan
30. on 7 Selecting the delay start 1 Select the programme and the required options 2 Select the delay start by pressing button 8 3 Press button 7 the machine starts its hourly countdown the programme will start after the selec ted delay has expired Cancelling the Delay Start after having started the programme 1 Set the washing machine to PAUSE by pressing button 7 2 Press button 8 once On the display will appear J 3 Press button 7 again to start the pro gramme www zanussi com Important The selected delay can be changed only af ter selecting the washing programme again The door will be locked throughout the delay time If you need to open the door you must first set the washing machine to PAUSE by pressing button 7 and wait a few minutes be fore opening the door After you have closed the door press the same button again Important The Delay Start cannot be selected with the draining programme Altering an option or a running programme It is possible to change some options before the programme carries them out Before you make any change you must pause the washing machine by pressing button 7 Changing a running programme is possible only by resetting it Turn the programme selector di al to Q and then to the new programme posi tion Start the new programme by pressing but ton 7 again The washing water in the tub will be not emp tied out Interrupting a programme Press t
31. product is disposed of correctly you will help prevent www zanussi com If you intend to drain the hose from the ma chine into a sink make sure that the sink is empty and the plug hole is not blocked Use the plastic U Piece supplied In the interest of the environment The appliance should be connected to the FOUL drainage system the water will then be taken to a sewage works for treatment before being discharged safely into a river It is essential that these appliances are not con nected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution If you require any further advice please contact your local water authority a N WASHING na MACHINE DISHWASHER RAINWATER RUN OFF SURFACE WATER FOUL DRAIN DRAINS amp SEWERS FOUL SEWERS UNTREATED SEWAGE TREATMENT DISCHARGE WORKS Y TREATED DISCHARGE C RIVER RIVER J potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your 29 household waste disposal service or the shop where you purchased the product Packaging materials The materials marked with the symbol are recyclable gt PE lt polyethylene gt PS lt polystyrene gt PP lt polypropylene This means t
32. r that eliminates all the spinning phases has been selected Select the draining or spinning programme The laundry is not evenly distributed in the drum Redistribute the laundry www zanussi com 23 Possible cause Solution There is water on the floor Unsatisfactory washing re sults The door will not open The machine vibrates is noisy Spinning starts late or the machine does not spin 24 Too much detergent or unsuitable detergent creates too much foam has been used Reduce the detergent quantity or use another one Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp Check the water inlet hose connection The drain or inlet hose is damaged Replace it with a new one The filter has not been properly screwed in after cleaning action Screw the filter fully in Too little detergent or unsuitable detergent has been used Increase the detergent quantity or use another one Stubborn stains have not been treated prior to washing Use commercial products to treat the stubborn stains The correct temperature was not selected Check if you have selected the correct temperature Excessive laundry load Reduce the laundry load The programme is still running Wait the end of washing cycle The door lock has not been released Wait until the door is released
33. rates a recirculation sys tem which allows an optimal use of the concen trated detergent Follow the product manufacturer s recommen dations on quantities to use and do not ex ceed the MAX mark in the detergent dispenser drawer Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used Follow the product manufacturers instructions on quantities to use Use less detergent if you are washing a small load the laundry is lightly soiled large amounts of foam form during washing Degrees of water hardness Water hardness is classified in so called de grees of hardness Information on hardness of the water in your area can be obtained from the relevant water supply company or from your lo cal authority If the water hardness degree is medium or high we suggest you to add a water softener following always the manufacturer s in structions When the degree of hardness is soft readjust the quantity of the detergent 13 Drying Hints Preparing the drying cycle As a dryer the appliance works on the conden sation principle Therefore the water tap must be open and the drain hose must drain water into a sink or into the drain pipe even during the drying cycle Attention Before starting the drying programme reduce the loads of washed laundry in order to obtain good performances Laundry not
34. s away from children Keep children and pets away from the appliance door when it is open If the appliance has a child safety device we recommend you ac tivate it General Safety Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket 2 www zanussi com Do not change the specification of this appliance Obey the maximum load volume of 8 kg refer to the Programme chart chapter If the supply cord is damaged it must be replaced by the manu facturer its service agent or similarly qualified persons in order to avoid a hazard The operating water pressure minimum and maximum must be between 0 5 bar 0 05 MPa and 8 bar 0 8 MPa The ventilation openings in the base if applicable must not be obstructed by a carpet The appliance is to be connected to the water mains using the new supplied hose sets Old hose sets must not be reused A Safety instructions Installation A Warning Risk of fire and electrical shock Remove all the packaging and the transit bolts Keep the transit bolts When you move the appliance again you must block the drum The appliance must be earthed Make sure that the electrical information on the rating plate agrees with the power sup ply If not contact an electrician Do not install or use a damagel appliance Always use a correctly installed shockproof Do not install or use the appliance where the socket temperature
35. s if the door can be opened light on the door cannot be opened The machine is working or has stopped with wa ter left in the tub light off the door can be opened The pro gramme is finished or the water has been emptied out light blinking the door is opening in a few minutes 10 Display The display shows the following information 10 1 10 2 Child safety lock This device permits you to leave the appliance unattended during it s functioning Duration of the selected programme After selecting a programme the duration is displayed in hours and minutes for example 2gs The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric After the programme has started the time remaining is updated every minute Selected drying time After selecting a drying programme the drying time is shown in minutes or hours and minutes After the programme has started the time remaining is updated every minute Delayed start The Selected delay set by pressing the relevant button appears on the display for a few sec onds then the duration of the selected programme is displayed again The delay time value decreases by one unit every hour and then when 1 hour remains every minute Alarm codes In the event of operating problems some alarm codes can be displayed for example Erg see paragraph What to do if Incorrect option selection If an option whic
36. speed will automatically assume the setting for cotton items if required reduce the speed to the desired level by pressing the button 2 Drain Draining of water Max load 6 kg For emptying out the water of the last rinse in programmes which stop with water in the tub Spin SPIN Drain and long spin Maximum spin speed at 1200 rpm ZKG 7125 1400 rpm ZKG 7145 1600 rpm ZKG 7165 Max load 6 kg Separate spin for hand washed garments and after pro grammes which stop with water in the tub You can reduce the spin speed to the required level by pressing the rele vant button to adapt it to the fabrics to be spun O Off For cancelling the programme which is running or to switch the machine off E 1 If you select the Super Quick option by pressing button 5 we recommend that you reduce the maximum load as indicated Full loading is possible however with somewhat reduced cleaning results 2 If using liquid detergents a programme without PREWASH must be selected 3 Available only with model ZKG 7125 Automatic Drying programmes Degree of Drying Type of Fabric Cupboard dry Cotton and linen bathrobes 3k Suitable for items to put away without ironing bath towels etc g Cupboard dry Synthetics and mixed fab Suitable for items to put away without ironing rics jumpers blouses under 2kg wear household linen Iron dry Cotton and linen sheets ta 3k Suitable for ironing blec
37. suitable for drying Particularly delicate items such as synthetic curtains woollen and silk garments with metal inserts nylon stockings bulky gar ments such as anoraks bed covers quilts sleeping bags and duvets must not be ma chine dried Avoid drying dark clothes with light coloured fluffy items such as towels as these can at tract the fluff Remove the laundry when the appliance has finished drying To avoid a static charge when drying is com pleted use either a fabric softener when you are washing the laundry or a fabric condition er specifically for tumble dryers Garments padded with foam rubber or mate rials similar to foam rubber must not be ma chine dried they represent a fire hazard Also fabrics containing residue of setting lo tions or hair sprays nail solvents or similar solutions must not be machine dried in order to avoid the formation of harmful vapours The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash pro gramme First use Ensure that the electrical and water connections comply with the installation instructions 14 If using liquid detergents a programme with out prewash must be selected Your appliance incorporates a re circulation system which allows an optimal use of the con centrated detergent Follow the product manufacturer s recommen dations on quantities to use and do not ex
38. ter hoses The appliance is to be connected to the wa ter mains using the new supplied hose sets Old hose sets must not be reused Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean The first time you use the appliance make sure that there is no leakage Use Warning Risk of injury electrical shock fire burns or damage to the appliance Use this appliance in a household only Do not change the specification of this appli ance Do not put flammable products or items that are wet with flammable products in near or on the appliance Do not touch the glass of the door while a programme operates The glass can be hot Make sure that you remove all metal objects from the laundry The final part of the drying cycle occurs with out heat cool down cycle to ensure that the items will not be damaged If you stop the appliance before the end of the drying cycle immediately remove and spread out all items so that the heat can dis sipate If you use detergent fabric softener or similar products obey the instructions on the pack aging Wipe away lint that has accumulated around the appliance Do not dry the damaged items which contain padding or fillings Do not dry items such as foam rubber latex foam shower caps waterproof textiles and rubber backed articles Before drying items that have been in con tact with substances such as
39. treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly Tar stains first treat with stain remover me thylated spirits or benzine then rub with deter gent paste Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the envi ronment Although biodegradable detergents contain substances which in large quantities can up set the delicate balance of nature The choice of detergent will depend on the type of fabric delicates woollens cottons etc the colour washing temperature and de gree of soiling All commonly available washing machine deter gents may be used in this appliance 1 do not use acetone on artificial silk www zanussi com powder detergents for all types of fabric powder detergents for delicate fabrics 60 C max and woollens liquid detergents preferably for low tempera ture wash programmes 60 C max for all types of fabric or special for woollens only The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash pro gramme If using liquid detergents a programme with out prewash must be selected Your appliance incorpo
40. tton and 2 kg for synthetic Note It is possible to dry up to 4 kg of cotton items by pressing Drying Time but ton only see the Drying Programme ta ble Do not use a dosing device ball when carrying out a washing and drying pro gramme 1 Load the laundry 2 Add detergent and fabric softener 3 Switch the machine on by turning the se lector dial to the selected washing pro gramme fabric 4 Select the required options by pressing the relevant buttons Note If possible do not select a spin speed low er than that proposed by the appliance to avoid too long a drying time therefore sav ing energy In any case the reduction of the spin speed is only possible after selecting drying 5 Select the drying time by pressing the but ton 4 or dryness degree by pressing the button 3 The display shows the entire du ration of the washing and the selected dry ing cycle 6 Start the programme by pressing button 7 After the programme has started the time remaining is updated every minute 7 At the end of the programme the buzzer sounds A flashing zero appear on www zanussi com the display At this point of the programme starts an anti crease phase which lasts about 10 minutes During this time the door is locked and the display keeps showing the flashing zero If you wish to open the door before or during the Fluff in the garments During the WASHING AND OR DRYING PHASE certain types of
41. um spin speed at 1200 rpm ZKG 7125 1400 rpm ZKG 7145 1600 rpm ZKG 7165 Max load 6 kg Reduced load 3 kg White or colour cotton heavily or normally soiled items Synthetics 60 30 Main wash Rinses Maximum spin speed at 900 rpm Max load 3 kg Reduced load 2 kg Synthetic or mixed fabrics underwear coloured gar ments non shrink shirts blouses www zanussi com SPIN RINSE HOLD SUPER QUICK EXTRA RINSE SPIN RINSE HOLD EXTRA RINSE SPIN RINSE HOLD SUPER QUICK EXTRA RINSE SPIN RINSE HOLD SUPER QUICK EXTRA RINSE SPIN RINSE HOLD SUPER QUICK EXTRA RINSE Detergent Com partment uij E E BEG E Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maxi Detergent Com partment mum Fabrics Load Type of Laundry Easy iron 40 Main wash Rinses Maximum spin speed at 900 rpm Max load 1 kg Synthetic or mixed fabrics selecting this programme the laundry is gently washed and spun to avoid any creas ing In this way ironing is easier Furthermore the machine will perform additional rinses Delicates 40 30 Main wash Rinses Maximum spin speed at 700 rom Max load kg 3 Reduced load kg 1 59 Delicate fabrics acrylics viscose polyester Wool Handwash 40 Cold Main wash Rinses Maximum spin speed at 900 rom Max load 2 kg Washing programme for machine washable wool as well as for hand washable
42. ussi com raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking nut but the machine MUST be level and stable Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration noise and displacement of the machine during operation Never place cardboard wood or similar materi als under the machine to compensate for any unevenness in the floor If necessary check the setting with a spi rit level Installation on suspended flooring Suspended wooden floors are particularly sus ceptible to vibration To help prevent vibration we recommend you place a waterproof wood panel at least 15 mm thick under the appliance secured to at least 2 floor beams with screws the wood panel must extend beyond the front feet If possible install the appliance in one of the corners of the room where the floor is more stable Water inlet Warning This appliance must be connected to a cold water supply Caution Before connecting up the appliance to new pipework or to pipework that has not been used for some time run off a reasonable amount of water to flush out any debris that may have collected Caution Do not use the hose from your previous appliance to connect to water supply The inlet hose is delivered with the machine 27 Connect the ap propriate end of the hose to a tap with a 3 4 thread Always use the hose supplied with the appliance
43. y little water without affecting performance The machine does not dry or The drying time or the dryness degree has not been selected does not dry properly Select the drying time or the dryness degree The water tap is not turned on Eig Open the water tap The drain filter is clogged Ef Clean the drain filter The machine is overloaded Reduce the laundry load in the drum The selected drying programme time or dryness degree was not suita ble for the laundry Select the suitable drying programme time or dryness degree for the laundry The laundry is full of differ The fabrics washed in the previous cycle released fluff of a different col ent colored fluff or refer to Fluff in the garments in chapter Use Washing amp Drying The drying phase helps to eliminate some fluff Clean the clothes with a fluff remover In case of an excessive amount of fluff in the drum repeat the following procedure twice Thoroughly clean the empty drum the gasket and the door with a wet rag Perform a rinse cycle Put a wool or piled fabric rag inside the drum Perform a drying cycle of 10 minutes Remove the old wool cloth Now you can wash other garments If you are unable to identify or solve the prob lem contact our service centre Before tele phoning make a note of the model serial num ber and purchase date of your machine the Service Centre will require this information Technica
Download Pdf Manuals
Related Search