Tekcomm TCT1500
Contents
1. choose the Transponder field and select the transponder with lt P gt Now you can turn your dish to get the highest Strength and Quality level If you have aligned your dish to maximum signal press OK to save Press the BLUE button to scan the position you have set For Astra 19 2E after a scan the list starts with a pre installed list followed with new found channels NOTE If your pre installed list Astra 19 2E is NOT giving any signal you are probably on the wrong satellite Press INFO button 3 x in viewing mode and try to get a high as possible signal for Strength and Quality 5 0 MAIN MENU All important settings and features of your receiver can be operated in Main Menu It consists of the sub menus TV Radio Accessory and Configuration To open the Main Menu press MENU 5 1 TV Press lt P gt to move to Main Menu In Main Menu press lt P to move to TV and press OK to enter the TV menu 5 1 1 TV Channels Use lt gt to reach the following sub menus Fav Lock Edit Move Sort Skip Delete and Search With the BLUE button you can change the available group you would like to use All Satellite Satellite7 Satellite2 Fav1 Fav2 etc 5 1 1 1 Favourites Press lt P to select if you wish to make favourite lists Press A to select the desired channel and press 1 9 to add the selected channel to 6 PART 2 English that favourite group you like to save Repeat this operation t2. 4 2 1 1 DiSEqC 1 0 1 1 For DiSEqC 1 0 1 1 you can select the satellite you want to use for LNB 1 2 3 and 4 Press AW for the LNB you want to use and press OK to edit Press the red button to add a satellite from the list Default LNB1 is set to Astra 19 2E You can press OK on for example LNB1 Astra 19 2E to see the signal level for Strength and Quality Now you can turn your dish to get the highest Strength and Quality level If you have aligned your dish to maximum signal press EXIT Use the colour buttons mentioned on the bottom screen RED Scan All GREEN Delete YELLOW Delete All BLUE Scan After a scan the list starts with a pre installed list followed with new found channels NOTE If your pre installed list Astra 19 2E is NOT giving any signal you are probably on the wrong satellite Press INFO button 3 x in viewing mode and TEKCOMM try to get a high as possible signal for Strength and Quality 4 2 1 2 DiSEqC 1 2 USALS DiSEqC 1 2 USALS need to be selected if your dish is mounted on DiSEqC 1 2 motor a First you need to set the LNB type you are using YELOW button b Then you have to select your Location GREEN button c To set your Limit positions the RED button will bring you in a new Set Limit menu Move continue or in steps to your end position East end West Select the RED button to Set West Limit position you have reached Select the GREEN button to Set East Limit
3. EPG NOTE The functions in the Radio EPG are identical to the TV EPG please read the chapters 5 1 2 for your reference TEKCOMM 5 3 Accessory In Main Menu press 4 to move to Accessory and press OK to enter the menu Press A Y to select the following sub menus Gomoku Calendar and Calculator 5 3 1 Gomoku Press A Y to select Gomoku and press OK Play the game Gomoku on your receiver Use the on screen help tips to set and play the game 5 3 2 Calendar Press AY to select Calendar and press OK Use the on screen help tips to search in your Calendar 5 3 3 Calculator Press AY to select Calculator and press OK Use the on screen help tips to use your Calculator 5 4 Configuration In Main Menu press 4 to move to Configuration and press OK to enter the menu Use AY to move to the following sub menus Installation TV Setup PIN Code Set Timer Set Default and SW Update 5 4 1 Installation Press A Y to select Installation and press OK This menu includes the following submenus OSD settings switch type and TP Manager 5 4 1 1 OSD settings NOTE For each function refer to chapters 4 1 as the functions are identical 5 4 1 2 Switch type NOTE For each function refer to chapters 4 2 1 as the functions are identical 5 4 1 3 TP Manager Press A Y to select a transponder you would like to Delete or to Scan To make a new transponder in your list you can use Add TEKCOMM You can use Delete
4. code 0000 5 4 3 3 Parental Control Press lt gt to change settings for Parental Control No Restriction All Programmes 02 18 This option will ask you for a pin code if you try to enter a channel with your restrictions Default pin code 0000 5 4 3 4 Change PIN Press lt P to change settings for Change PIN Yes or No If you select Yes this option will ask you to Enter Old PIN code first and then you will be asked to Enter New PIN for 2 times 5 4 4 Set Timer Press A Y to select Set Timer and press OK This option will bring you to a timer screen To Add a timer push the RED button and use AY lt gt to change settings Your receiver will switch to the right channel at the right time even from standby You are able to set 10 timers at most If you would like to change a timer setting use AY to highlight the timer number and use the RED button for Edit or the GREEN button to Delete 5 4 5 Set Default Press A Y to select Set Default and press OK A pop up screen will ask you Set factory default Press OK or EXIT Please be careful when using this function as it will erase all the data and parameters you may have set earlier Once you have set to Default you will have to re install your preferences and re scan channels The receiver will return to its factory default state and all user data will be deleted NOTE Before you set to Default make a backup on a USB Device Chapter 5 4 6
5. is without display Check that the power cord is plugged into the wall outlet Switch ON receiver Your model is without display No picture or sound Wrong connection of the Audio Video output of the receiver to TV Connect the Audio video output of the receiver to TV correctly Audio muting Wrong Audio channel Press the Mute button Press AUDIO button and select other audio channel TV power off wrong channel or input Turn on TV select correct channel or input No picture The receiver can t receive the signal Check the antenna cable replace the cable or connect the cable to the receiver tightly Incorrect values of some tuner parameters Set the values of the tuner parameters correctly in the installation menu Wrong direction of the dish Check the signal strength with a spectrum analyzer and adjust your dish correctly The remote control does not work The batteries of the remote control are not inserted or exhausted Check whether the batteries are inserted correctly in your remote control Check the batteries and if exhausted replace the batteries in the remote control The USB storage device is not recognized Wrong formatted Make sure that your USB device use file system FAT32 The external USB HDD does not start Power consumption is too high Connect extra power supply adaptor to your USB HDD The receiver switches off automatica
6. to move to Update by USB and press OK USB device should be connected An Update Files list will pop up and you can use AW lt P gt to highlight the software you want to load TEKCOMM Press OK and confirm the new request System Update and press OK for Yes or EXIT for exit NEVER disconnect the USB device from the receiver the receiver from the main or switch the power OFF during the update backup procedure It can damage your receiver and warranty will void As soon as the update has been finished the receiver restarts automatically WARNING NOTE You can also load a backup file with your backup settings See chapter 5 4 6 3 5 4 6 3 Backup to USB Use AY to move to Backup to USB and press OK USB device should be connected To backup your User Database press OK and it will save your User Database You can use this Backup File in Update by USB Read chapter 5 4 6 2 WARNING NEVER disconnect the USB device from the receiver the receiver from the main or switch the power OFF during the update backup procedure It can damage your receiver and warranty will void As soon as the update has been finished the receiver restarts automatically 6 0 CHANGING CHANNEL LIST MODE To change between TV and Radio channel lists use TV RADIO in normal viewing mode To change channel list to Favourite in normal viewing mode press FAV Use FAV again to select other favourite groups or Satlists Now select the des
7. 3 Backup to USB PART 2 English NOTE Your PIN code will change back to the factory setting 0000 5 4 6 SW Update Press AY to select SW Update and press OK Use AY to move to the following sub menus Update by OTA Update by USB Backup to USB OTA Update by USB Backup to USB 5 4 6 1 Update by OTA This function will search for new software on satellite An Update by OTA menu will pop up and you can edit this menu with A V lt P gt and the numeric buttons to change the details Press OK to scan directly For OTA in Standby you can set Manual AUTO and Disabled Default It will scan Manual at 04 00 o clock am at this default setting for new software If you want to search for other frequencies automatically please change OTA in Standby to AUTO Change OTA in Standby to Disabled if you don t want to use this function NOTE Needed parameters can be changed Please ask your local TekComm dealer in case software update was not successful WARNING During the Update process NEVER disconnect the receiver from the main or disconnect the receiver from the antenna cable This can damage your receiver and warranty will be void After the update the receiver restarts automatically 5 4 6 2 Update by USB a Download the required update file for your receiver model from our website www tekcomm tv b Unzip the file copy it to your USB device and connect it to the USB port of your receiver c Use A Y
8. ARNING The batteries should not be recharged disassembled electrically short circuited be mixed or used with other types of batteries If rechargeable accumulators instead of batteries are going to be used we recommend using e g NiMH types with low self discharge to ensure long time operation of remote control 1 5 Usage of external USB devices It is recommended to use USB 2 0 storage devices TekComm cannot guarantee compatibility to all types of USB storage devices It is advised not to store important information on USB storage devices used with the receiver Always make backups of data on USB storage device before usage with receiver TekComm will not take responsibility for any loss of information or circumstances caused by loss of information 2 0 YOUR RECEIVER 2 1 Front Panel 1 INDICATION LED Green LED during operation red LED in standby mode 2 REMOTE SENSOR Reception of remote control signals 3 USB CONNECTION Connection to USB storage device Fig 1 2 2 Rear Panel Fig 2 1 SAT OUT A Loop through to connect an extra receiver to the satellite signal from dish 2 SATIN To connect to the LNB for satellite signal from dish 3 TV SCART To connect to your TV set using a SCART cable 4 S PDIF coax To connect to the input of your digital audio amplifier 5 Power Cord Your receiver requires a mains voltage of 100 240 V AC TEKCOMM Auto selectable 50 60Hz 5 Make sure to check the pow
9. All to delete all channels from the list RED Add GREEN Del YELLOW Delete All BLUE Scan See bottom line 5 4 2 TV Setup Press A Y to select TV Setup and press OK Use A Y to move to the following sub menus TV Format TV System OSD Transparency Banner Display Time and Video Output 5 4 2 1 TV Format Press lt P to change settings for TV Format 4 3 LB 4 3 PS 16 9 PB 16 9 AUTO 5 4 2 2 TV System Press lt P to change settings for TV System PAL NTSC AUTO 5 4 2 3 OSD Transparency Press lt gt to change settings for OSD Transparency 1 8 5 4 2 4 Banner Display Time Press lt gt to change settings for Banner Display Time 1sec 3sec 5sec 10sec 30sec Always 5 4 2 5 Video Output Press lt P to change settings for Video Output RGB or CVBS RGB will give you the best performance 5 4 3 PIN Code Press A Y to select PIN Code and press OK Use AY to move to the following sub menus Menu Lock Channel Lock Parental Control and Change PIN 5 4 3 1 Menu Lock Press lt gt to change settings for Menu Lock Yes or No This option will ask you for a pin code if you like to enter the menu Default pin code 0000 NOTE With active menu lock some functions in the channel editing are not available PART 2 English 5 4 3 2 Channel Lock Press 4P to change settings for Channel Lock Yes or No This option will ask you for a pin code if you try to enter a locked Channel Default pin
10. T TIME INSTALLATION 4 1 OSD Settings 4 2 My Dish 5 0 MAIN MENU 5 1 TV 5 2 Radio 5 3 Accessory 5 4 Configuration 6 0 CHANGING CHANNEL LIST MODE 7 0 AUDIO LANGUAGE SELECTION 8 0 TELETEXT 9 0 SUBTITLES 10 0 TROUBLE SHOOTING 11 0 SPECIFICATIONS TekComm declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004 108 EEC and 73 23EEC RoHS 2002 95EEC Subject to alterations In consequence of continuous research and development technical specifications design and appearance of products may change All product names are trademarks or registered trademarks of their respective owners TekComm 2011 All rights reserved 07 2011 TEKCOMM O NNNOO OAD ARARA mwoww WNNNYNN 10 11 12 TEKCOMM 1 0 INTRODUCTION 1 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER In a closed or poorly ventilated cabinet directly on top of or under any other equipment on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES To direct sunlight or near any other equipment that generates heat to rain or intense moisture to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects such as loudspeakers transformers etc Do not use a damaged power cord It may cause a fire or an electrical shock Do not touch a power cord with wet hands It may cause an electric shock W
11. TEKCOMM Digital Satellite Receiver TCT 1500 1 User Manual AT 0820 400 150 0 12 Min sterr Festnetz support_at tekcomm tv DE 0180 501 49 91 0 14 Min deutsches Festnetz 0 42 max Min Mobilfunknetze support_de tekcomm tv www tekcomm tv Fig 1 TEKCOMM Fig 2 CAUTION Model Digital Satellite Receiver TCT 1500 100 240 V Een 0 ES 0 HOW mas o 0 0 O CS 4 a 3 4 5 Fig 3 Fig 6 Fixed satellite Dish SCART cable Fig 7 Fixed satellite Dish Fig 8 Fixed satellite dish 1 Fixed satellite dish 2 E ex pointed at ASTRA ex pointed at HOTBIRD DiSEqC Switch OUT Mode ig Salle Receiver TCT 1500 Fig 9 TEKCOMM USB Device PART 2 English TABLE OF CONTENTS 1 0 INTRODUCTION 1 1 Safety Instructions 1 2 Storage 1 3 Equipment Set up 1 4 Accessories 1 5 Usage of external USB devices 2 0 YOUR RECEIVER 2 1 Front Panel 2 2 Rear Panel 2 3 Remote Control Unit 2 4 Default PIN code 0000 2 5 Installing the Batteries 2 6 Using the Remote Control 3 0 CONNECTIONS 3 1 Basic connection with SCART cable 3 2 Connecting to Satellite Dish 3 3 Connecting to a Digital Audio Amplifier 3 4 Connecting to USB device 4 0 FIRS
12. er specification before connecting your receiver to the wall outlet 2 3 Remote Control Unit Fig 3 Turns the receiver On Stand by 2 Mutes audio output of the receiver Changes channel and controls numeric functions Opens the available favourite list if previously configured Toggles between the two the last watched channels Opens the audio language s and mode selection Opens the subtitle language s selection Shows the information banner Displays the main menu and returns to the previous level of menu Opens the EPG Electronic Programme Guide in TV mode Exits from any menu and sub menu or cancels the progressing function Switches to the previous next programme in TV mode Moves the cursor upwards downwards in menu mode In TV mode it displays the channel list according to the chosen mode In menu mode activates the highlighted menu item Increases decreases the volume level in TV mode Changes settings for specific menu items in menu mode Opens the Teletext language s selection Freezes your live audio and video press again to cancel 1 3 0 9 4 FAV 5 RECALL 6 AUDIO 7 SUBTITLE INFO MENU oo 10 EPG 11 EXIT 12 4V 13 OK 14 4 15 TEXT 16 PAUSE TEKCOMM 17 COLOURED BUTTONS For Teletext and further menu functions In viewing mode toggles between TV and radio mode 2 4 Default PIN code 0000 18 TV RADIO 2 5 Installing the Batteries Fig 5 Remove
13. hen the receiver is not used for a long period of time you should unplug the power cord from the wall socket Do not use alcohol or ammonia based liquids to clean the receiver If you wish you may clean your receiver with a soft lint free cloth slightly made damp with a mild soap solution only after disconnecting from the mains voltage supply Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside Safety Precautions Never open the receiver cover It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards and your warranty will be void Refer all maintenance or servicing to suitably qualified personnel When you are connecting cables be sure that the receiver is disconnected from the mains supply voltage Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment It is a necessity that you only use an approved extension and compatible wiring that is suitable for 2 PART 2 English the electrical power consumption of the installed equipment Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver If the receiver does not operate normally even after strictly f
14. ired channel and press OK to switch to full screen mode 7 0 AUDIO LANGUAGE SELECTION Press AUDIO to select the audio language Select Audio Channel or Audio mode with AV TEKCOMM lt gt and make your selection Stereo Left or Right channel Press OK Exit and confirm Your selection will be memorized for the current channel NOTE Audio tracks containing AC3 can only be listened to if the receiver is connected to a digital audio amplifier and this amplifier is switched ON and set to the correct input 8 0 TELETEXT Press TEXT in normal viewing mode and lt gt to increase or decrease the displayed page number Use 1 9 buttons to input a page directly 9 0 SUBTITLES Press SUB in normal viewing mode If the current channel broadcasts subtitle information the Subtitle Language selection menu will appear Use AW lt gt to select what you want press OK Exit and confirm 10 PART 2 English PART 2 English 10 0 TROUBLE SHOOTING There may be various reasons for occurring abnormal operation of the receiver Check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact the dealer Don t open the receiver cover This may cause a dangerous situation and will void warrant TEKCOMM Cause Remedy Solution The display on front panel does not light up The power cord is not plugged in Receiver is in stand by mode Your model
15. lly Auto Standby function enabled Disable Auto Standby See section 4 1 4 for details 11 TEKCOMM 11 0 SPECIFICATIONS Demodulator Modulation QPSK Input Symbol Rate 2 45 Ms s SCPC amp MCPC signals from C amp KU and satellites Video Decoder Profile level MPEG 2 MP ML Input Rate Max 60 Mbits s Video Resolution 720 x 576 pixels PAL 720 x 480 pixels NTSC Aspect Ratio 4 3 16 9 Audio Decoder ISO IEC 11172 LAYER 1 amp 2 Sampling rate 32 44 1 48 kHz Audio modes Stereo Dual mono Mono Tuner Front End DVB S Input Frequency Range 950 2150 MHz RF Input Level 25 65 dBm LNB Power 13 18 V DC 4 5 max 500 mA Overload protected DiSEqC Version 1 0 1 1 amp 1 2 GOTO X System and Memory Flash Memory 1 6 Mbits SDRAM 128 Mbits Connectors SAT IN SAT OUT SCART TV RGB CVBS S PDIF coaxial output USB port 12 PART 2 English General Data Input Voltage Range 100 240 V AC 50 60 Hz Power consumption max 18W typ 4 5 W Stand by Power consumption 1 00 W Operating Temperature 0 C 40 C Storage Temperature 30 C 80 C Operating Humidity Range 10 85 RH Non condensing Size WxDxH 180 x 130 x 45 mm Weight ca 0 457 kg PART 2 English TEKCOMM TEKCOMM PART 2 gt English
16. o remove the channel from the favourite list Press YELLOW button to save 5 1 1 2 Lock Press lt P to select 8 Then press AY to select the desired channel and press OK to lock this channel Press YELLOW button to save NOTE This only works if Channel Lock is switched ON in the Pin Code menu from the Configuration menu Default Pin Code is 0000 5 1 1 3 Edit Press lt P to select 4 then press AY to select the desired channel and OK to edit this channel Press YELLOW button to save 5 1 1 4 Move Press 4P to select N then press A Y to select the desired channel and OK to move this channel Use AY to move the channel to its new location and press OK to confirm Repeat this for every channel you want to move Press YELLOW button to save all your changes 5 1 1 5 Sort Press lt P to select 4 You can sort channels by Name A Z Name Z A with the RED button or Pay Free or Free Pay with the GREEN button Press MENU or EXIT to return the menu The list is now sorted by the specified order NOTE Please take care once desired order is executed this order stays 5 1 1 6 Skip Press lt gt to select e then press AY to select the desired channel and OK to skip this channel During zapping in viewing mode it will pass the skipped channel Press YELLOW button to save 5 1 1 7 Delete Press lt gt to select then press A Y to select the desired channel and OK to delete this channel Press the YELLOW but
17. ollowing the instructions in this user manual it is recommended to consult your dealer 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from children For transporting the receiver from one place to another or if you are returning it under warranty conditions make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 1 3 Equipment Set up We recommend you consult a professional installer to set up your equipment Otherwise please follow the instructions below Refer to the user manual of your TV and your antenna Make sure that the SCART cable and outdoor components are in a good condition and the SCART connection is well shielded This manual provides complete instructions for installing and using this receiver The following symbols will serve as follow Warning Indicates warning information Tips Indicates any other additional important or helpful information MENU Represents a button on the remote control or the receiver Bold Character Move to Represents a menu item within a window Italic Character 1 4 Accessories 1 TCT 1500 1x 2 User s Manual 1x 3 Remote control unit 1x PART 2 English 4 Batteries AAA type 2 x W
18. position you have reached d Satellite positions Press A Y to select the Position you like to use and press OK Press the RED button to Add SAT you like to install Select a transponder receivable at your location choose Transponder field and select the transponder with lt gt Then choose GOTO X and press OK The dish will turn fast close to the right position Use the Move Step field for Fine Tuning and adjust the position of the dish with the lt gt buttons Once the dish is adjusted to the desired position select the OK field and press OK to save Press the BLUE button to scan the position you have set For Astra 19 2E after a scan the list starts with a pre installed list followed with new found channels You can save 32 satellite positions NOTE If your pre installed list Astra 19 2E is NOT giving any signal you are probably on the wrong satellite Press INFO button 3 x in viewing mode and try to get a high as possible signal for Strength and Quality 4 2 1 3 NONE Toneburst If you have no DiSEqC 1 0 1 1 or DiSEqC 1 2 USALS you can select NONE Press A Y to select Toneburst and use lt gt buttons to switch it OFF ON TEKCOMM For Toneburst OFF you can edit 1 dish For Toneburst ON you can edit 2 dishes Press A Y to select Receiver and press OK Here you can edit the dish settings Press the RED button to Add SAT you like to install Select a transponder receivable at your location
19. the battery cover from the remote control and put 2xAAA size batteries inside the compartment The diagram inside the battery compartment shows the correct way to install the batteries 1 Open the cover 2 Install batteries 3 Close the cover 2 6 Using the Remote Control Fig 4 To use the remote control point it towards the front of the digital receiver The remote control has a range of up to 7 metres from the receiver at an angle of up to 60 degrees The remote control will not operate if its path is blocked NOTE Sunlight or very bright light will decrease the sensitivity of the remote control 3 0 CONNECTIONS 3 1 Basic connection with SCART cable Fig 6 3 2 Connecting to Satellite Dish Connecting a fixed satellite dish to your receiver Fig 7 PART 2 English Connecting multiple fixed dishes to your receiver using a DiSEqC 1 0 switch Fig 8 3 3 Connecting to a Digital Audio Amplifier Connect your Digital Audio Amplifier with the S PDIF connector on the back of the receiver Fig 7 3 4 Connecting to USB device Fig 9 4 0 FIRST TIME INSTALLATION Ensure your satellite signal is of good quality It is recommended that you perform the first time installation by following the Installation as described step by step It will help you to easily achieve system configuration and installation setup 4 1 OSD Settings Press OK AY and lt gt to change settings for OSD Language Audio Language Subti
20. tle Language AUTO Standby Auto Time Zone and Time Zone 4 1 1 OSD Language Use this option to change the language of the OSD Use lt P to select OSD language to German French or English 4 1 2 Audio Language Use this option to change the language of the Audio Use lt P to select Audio language to German French or English 4 1 3 Subtitle Language Use this option to change the language of Subtitles Use lt P to select Subtitle language to German French English or OFF 4 1 4 Auto Standby This option allows you to enable Auto Standby or to disable Auto Standby Auto Standby will switch the receiver to standby automatically when it doesn t receive commands from the remote control for a period of 3 hours To avoid the automatic switch off use lt P to set Auto Standby to OFF PART 2 English 4 1 5 Auto Time Zone This option allows you to enable Auto Time Zone or to disable Auto Time Zone If switched ON it will follow the time zone automatically where you are Use lt gt to set Auto Time Zone to OFF ON 4 1 6 Time Zone Use this option to set the time zone manual Only possible if Auto Time Zone is OFF You can make a selection from 12 00 till 12 00 Steps of 30 minutes 4 2 My Dish Press OK AY and lt P to change settings for Switch Type Toneburst and DiSEqC 4 2 1 Switch Type Use lt P to select the the Switch Type of your dish You can select DiSEqC 1 0 1 1 DiSEqC 1 2 USALS or NONE
21. ton to save and confirm or exit the pop up screen With the GREEN button you can select the whole list to delete PART 2 English 5 1 1 8 Search Press lt P to select then press OK and use the On Screen Display menu to search for a programme 5 1 2 EPG Electronic Programme Guide The EPG shows the programme schedule for all services broadcasting EPG information NOTE Not all broadcasters provide programme information Press AY to select the desired channel and the right screen will show you the available EPG Press lt to step in to the EPG schedule for the current channel and use AV for EPG and lt gt to change Date Use OK for more details on the selected EPG Press EXIT to leave 5 1 3 Programming Timer from EPG Book the selected programme in EPG screen with the RED button A Timer Settings menu will pop up and you can edit this menu with A V lt P gt and the numeric buttons to set the timer details Press OK to save The receiver will switch on to the right programme at the right time 5 2 Radio Press MENU to move to Main Menu then press lt gt to move to Radio and press OK to enter the Radio Channels menu 5 2 1 Radio Channels Press AY or OK to move to Radio Channels Use gt lt to move to the following sub menus Fav Lock Edit Move Sort Skip Delete and Search Press EXIT to leave NOTE For each function refer to chapters 5 1 1 1 to 5 1 1 8 as the functions are identical 5 2 2 Radio
Download Pdf Manuals
Related Search