LG VR5942L
Contents
1. Press the START STOP button when the power switch is turned on If the power is not turned on or if there is no display but only the Ting sound put the HOM BOT on the home station If there is no change even when HOM BOT is attached to the home station press the reset switch located on the rear side of the home station while the HOM BOT is attached on the home station HOW TO START AND STOP CLEANING After the HOM BOT is turned on press the START STOP button to begin cleaning A melody will sound and cleaning will begin Press the START STOP button during the cleaning cycle to stop cleaning When the START STOP button is pressed while the power supply of the HOM BOT is turned off the power will be turned on Press the START STOP button one more time to start cleaning After the HOM BOT is turned on press the START button on the re mote control A melody will sound and cleaning will begin Press the STOP button during the cleaning cycle to stop cleaning x The HOM BOT cannot be turned on from Stand By by using the remote control when the power of the HOM BOT is off When the power is off press the START STOP button on the upper side of HOM BOT to turn the power on and to allow the remote to be used When the START button on the main unit or remote control is pressed HOM BOT will start cleaning in Spatial expansion mode x During cleaning collisions can happen when the sensor cannot2. BOT s brush can damage the carpet If this happens immediately stop the cleaning operation When a carpet has long tassels the tassels can be damaged Do not let the main frame and charging terminal of the home station come into contact with metallic objects Doing so can cause product failure Do not put water detergent etc into the HOM BOT Doing so can cause product failure Do not put any water or detergent on the HOM BOT If liquids get inside of the HOM BOT turn off the power supply and contact an LG Electronics sales agent or customer care center If the floor is wet or has wet spots wipe them up before using the HOM BOT Do not use the HOM BOT on a wet surface Failure to do so can cause product failure Tip Check the following items before use Do not allow the HOM BOT to sweep up liquids blades thumb tacks kindling etc These items can cause product failure Do not put sharp objects into the opening of the HOM BOT s supersonic sensor Doing so can cause product failure Do not use the HOM BOT when the dust bin is completely filled up Doing so can cause product failure When the robot cleaner is operating it may hit Chairdesk and table legs or other narrow pieces of furniture For quicker and better cleaning place the dining chairs on top of the dining table e Remove fragile or unnecessary objects from the room to be cleaned For example remove e
3. Inside of the outline will be cleaned with zigzag traveling When the Ist 2nd stages are completed the inside of the house will be cleaned through the repetition of above cleaning method as the device is being moved to the next cleaning area Tip e The cleaning mode can only be changed with the remote control AUXILIARY CLEANING MODES CD This method of cleaning involves manually moving the HOM BOT by pressing the directional arrow buttons on the remote control The interior space will be cleaned by the HOM BOT as it is being moved to the front rear or rotated to the left and right side according to the input of the directional buttons Use this cleaning method when concentrated cleaning of a small interior space is required After moving the HOM BOT to the location to be cleaned press the SPOT button on the remote control The spot cleaning icon will illuminate on the HOM BOT and concentrated cleaning will be performed for a space within a radius of 1 m 3 28 ft x During charging the spot cleaning button on the remote control will not activate TIMER CLEANING Hom Bot can be scheduled to start cleaning after a certain period of time The time can be set among 2 hours 6 hours and 12 hours 1 When HOM BOT is connected to the charging station the cleaning time can be set by pressing the TIMER button on the remote 2 Adjust the time by multiple pressures on
4. REMOTE CONTROL CD Start The HOM BOT will start cleaning e3 Charging The HOM BOT will move to the home station for charging Directional button The HOM BOT will move as desired by the user to front rear left and right sides for cleaning Stop If the HOM BOT is in operation it will be stopped If it has been set for timer cleaning the timer will be canceled Spot Cleaning will concentrate within a space of about 1 m 3 28 ft The timer can be set from 1 12 hours in advance Zigzag cleaning and then spatial expansion The Hom BOT will clean while maneuvering in a zigzag pattern and then expand the cleaning area Tip e he HOM BOT s power supply cannot be turned on with the remote control e To turn on the power supply use START STOP button on the top of HOM BOT e In order to do spot cleaning timer cleaning zigzag cleaning and spatial expansion cleaning you must first stop the operation of the HOM BOT e If the main power switch on the underside of the HOM BOT is turned off the remote will not func tion and the battery cannot be charged e If the main switch on the underside of the HOM BOT is in the off position the Status display will flash and sound when the unit is manually placed onto the home station to indicate that the main switch is off DISPLAY STATUS INFORMATION Battery and timer hour indication e When in Stand by without any timer setting the remaining b
5. When the HOM BOT is attached to the home station and a TING sound is generated repeatedly please check and ensure that the main On Off on the underside of the HOM BOT is in the ON position Method 2 When the HOMING button of the remote control charging will start automatically when the HOM BOT has returned to the Home Station x If the HOM BOT is within 10 cm 3 9 in of the front of the charging terminal while the power supply is turned on it will automatically be returned to the home station and charging will begin Tip Take the following precautions when using the home station e f foreign material is caught in the charging terminal charging may not proceed smoothly Wipe the terminal from time to time with a dry cloth after the power plug is disconnected e To prevent electric shock do not touch the charging terminal with any metallic objects e To avoid fire or electric shock never disassemble or modify the home station e Do not to place the home station or power plug near to a heating appliance HOW TO CHARGE THE BATTERY The remaining battery charge can be confirmed from the charge indication lights which will indicate charge as follows e During charging the charge remaining indication lights will flicker e When charging is completed at the home station only the battery icon will illuminate to save power e The battery icon will flicker when battery charging is required X ci i rj Full charging High Mid
6. and clean it with a cleaning brush or under running water 6 After cleaning with water completely dry the dust bin in a well ventilated area out of the direct sunlight T When you have completed cleaning the dust bin close the cover and replace the sponge filter and HEPA filter 8 Put the dust bin into the HOM BOT and close the dust bin cover Tip e After cleaning always mount the dust bin filters HEPA filter sponge filter to the dust bin If they are not mounted dust may enter the HOM BOT interior and cause product failure e When dust bin filter HEPA filter soonge filter is full the warning sound empty the dust bin may be generated In this case clean the filter by referring to cleaning of dust bin filter on page 23 CLEANING THE DUST BIN FILTER CD The dust bin filters are comprised of the HEPA filter and the sponge filter Clean the HEPA filter and the sponge filter according to the following sequence 1 Separate the HEPA filter and the inside sponge filter by removing the HEPA filter as shown 2 Carefully clean any fine dust off the HEPA filter and the sponge filter with a vacuum cleaner or water 3 After washing the HEPA filter and the sponge filter with water place them out of direct sunlight and allow them to dry completely 4 Mount the cleaned HEPA filter and sponge filter into the dust bin according to the sequence shown to the right When assem bling the filter the fi
7. charged page 17 Movements or travel path are gt Carefully wipe the sensor with a smooth cloth page 24 abnormal gt Turn on the power switch off and on Suction power becomes weak gt Check whether there is foreign material blocking the suction port page 23 gt Empty the dust bin page 21 gt Clean the dust bin filter page 22 Noise becomes louder gt Confirm that the dust bin has been fitted properly gt Confirm that the dust bin filter has been fitted properly page 22 gt Check whether foreign material is caught in the brush page 23 The HOM BOT cannot be gt Replace the remote control batteries page 11 activated with the remote gt Confirm that the control is within the coverage area of the main control frame which is up to 3 m or 9 84 ft page 11 The brush does not rotate gt Clean the brush page 23 gt Confirm that the brush has been fitted properly page 23 The HOM BOT will not charge gt Remove objects around the home station page 13 gt Confirm that the power supply is connected to the home station page 13 gt Wipe the charging terminal with a dry cloth The power supply This is not a failure HOM BOT has its own power saving function If it is automatically turns off not used for ten minutes after the power supply is turned on the power will automatically turn off The power supply cannot be Check that the power switch on the underside is turned on Page 14 turned
8. detect objects because of their shape When this happens the internal impact detecting sensor will activate and engage a backward motion x If the HOM BOT is set to start cleaning at a location away from the home station put the device on a flat floor in order to prevent a malfunction of the obstacle detecting sensor In addition start cleaning from a location where there are no obstacles such as curtains or walls within 30 cm 11 8 in of the HOM BOT Tip For best results e Briefly scan the area to be cleaned for big and small objects that may cause difficulty for the HOM BOT e If cleaning is started when the HOM BOT is at the home station the device can rapidly be re turned to the home station as the current home position has been accurately read HOW TO CHARGE THE BATTERY The HOM BOT returns to the home station at the end of a cleaning cycle or when its battery is running low x If the HOM BOT is unable to dock to the home station on its first at tempt it will try again until it docks successfully x When the HOM BOT has cleaned all areas that it can clean it will return to the home station even when the battery level is not low If using the HOM BOT for the first time or to charge the battery by interrupting the cleaning you can manually charge the battery Method 1 Attach the HOM BOT to the home station by matching up the two arrows on the HOM BOT and the home station A melody will sound and charging will begin x
9. on PRODUCT SPECIFICATIONS Item Model EG Obekine RZECZE External dimensions D360 mm X 90 mm Weight 3 2 kg Power consumption 15 W Battery fully charged DC 16 6 V Maximum Traveling 350 mm sec Velocity Use time Approx 90 minutes 1 time charging Based on general floor surface Charging time 3 hours Main functions Obstacle detection function Falling prevention function Timer cleaning function Error indication function Dry mop function wiping option Automatic manual charging function Edge cleaning function Voice announcement function Map building function Spot cleaning function Zigzag cleaning function cell by cell Item Model Home station VR594 External dimension 204 mm X 158 mm X 125 mm Rating AC 220 240 V 50 Hz Output voltage current 171vVDC 1IA Power consumption 23 W Item Model Battery EAC60766102 Charging battery Lithium polymer Nominal voltage 14 8 V 1900mAh MEMO LG Life s Good
10. size PARTS DESCRIPTION HOM BOT Plan view Dust bin cover button Dust bin cover State indication lamp Manipulation Button Detecting sensor of home station amp receiving sensor of remote controller Front view Ultrasonic sensor _ 0 Ventilation port Cliff detection sensor Charging terminal Brush Side brush Wheel Lower camera sensor Battery Power switch b Figures can be different from actual objects PART DESCRIPTION HOME STATION DUST BIN CD m Power lamp gt Charging terminal Reset button Power cord fixing groove D a Suction port cover N A o Sponge filter 7 AT o ooo f I i Sle ee HHH Dust bin cover opening button a WY so ot BNIN HEPA filter b Figures can be different from actual objects BUTTON FUNCTIONS HOM BOT CD e Press the START STOP button to turn the HOM BOT on off or start stop cleaning e Press the START STOP button while the HOM BOT is on and it will automati cally start cleaning e f the START STOP button is pressed during automatic cleaning the HOM BOT will stop cleaning e Press and hold the START STOP button for approximately two seconds to turn off the HOM BOT e This puts the HOM BOT into the Stand By mode e If the button is pressed while in the timer mode the timer setting will be canceled BUTTON FUNCTIONS
11. Model VR5942L English Color cover body 141 Weight 80g Size W H 190x260 mm 2012 3 26 MFL67086051 Chage Record LG Life s Good OWNER S MANUAL CLEANING ROBOT Before using please carefully read the Safety Precautions pages to allow for safe operation of the product After reading the operation manual please keep it in an easily accessible location VR59 L YRT JI WI www lg com MFL67086051 FEATURES Camera sensor Images of the floor are obtained from the sensors of the lower camera and through this the location of HOM BOT will be confirmed therefore elaborate cleaning can be accomplished for every part of the room As the height of the HOM BOT is low 9Omm even the underside of a framed bed or furniture can be cleaned As the noise levels are at a quiet 6OdB cleaning can be performed at night Less than 60dB The HOM BOT can clean all parts of the area by cleaning in zigzag mode and then in spatial expansion mode The HOM BOT also has voice confirmation and instruction that can be easily understood by the user CONTENTS 4 BEFORE USING ADDITIONAL INFORMATION 1 4 Safety Precautions 26 28 Troubleshooting 5 Included with Product 29 Before You Call for Service 6 7 Parts Descriptions 8 9 Button Functions 9 10 Display Status Information REFERENCE 11 Before You Start 30 Product Specifications 12 Overview 2 HOW TO USE 13 How to Install the Home Sta
12. SENSOR CHARGING TERMINAL There are sensors on the HOM BOT that can detect obstacles stairways and the home station for charging the battery In order to maintain the performance of the HOM BOT regularly clean the sensors and charging terminal as follows 1 Lay a smooth cloth on the floor overturn the HOM BOT and put it on the cloth 2 Turn off the power switch on the bottom of the HOM BOT Injury can be caused by the activation of the HOM BOT if the main power is not turned off 3 Use a smooth cloth or cleaning brush to wipe the dust off each sensor and the charging terminal as described below Obstacle detection sensor Receiving sensor of AA remote controller 4 Camera sensor CIiff detection sensor LITA c Charging terminal Ae a a LE A dll Charging terminal NADM Lens Tip e Do not clean the HOM BOT by directly spraying it with water thinner benzene etc e Call the service center if the sensors or charging terminals are damaged Sensor and terminal damage can cause the product to malfunction CLEANING THE SIDE BRUSH CD Foreign objects materials such as hair can easily adhere to the side brush Remove such materials at least once a week If excessive amounts of foreign materials are stuck to the brush there is a risk of damage to the brushes If the floor is rough or wall skirtings are frequently cleaned the side br
13. Service Agent in order to avoid a hazard This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user mainte nance shall not be made by children without supervi sion SAFETY PRECAUTIONS GN For your safety do not remove the battery from the Roboking If you need to replace the battery or the Roboking take it to the nearest authorized LG Electronics service center or dealer for assistance ETET ZE Failure to follow this warning can cause fire or product failure Never use the Roboking with a bat tery and or home station from any other product than the Roboking Doing so can cause fire or product failure Do not use the Roboking when candles or fragile objects are placed on the floor 2020000000000000000000000000000000000000000000000000000000000000 Doing so can cause fire or product failure Make sure the power cord of the home sta tion is not crushed under a heavy object or damaged by contact with sharp objects 2220200000030000000000000000000000000000000000000000005000000000 product failure If the power cord is broken replace it at an LG Electronics customer care center Do n
14. at the vacuum may accidentally hit or bump into 5 Do not allow children to sit on the vacuum 6 Do not use the vacuum on a wet surface SAFETY PRECAUTIONS N WARNING Do not spray or suck in inflammable materials surfactants or drinking wa ter in the vicinity of the Roboking 22 000200000000000000000300000000000000000000080000000000000008050 Doing so can cause fire or product failure Inflammable materials gasoline thinner etc Surfactant detergent articles for bath etc Do not insert any part of the body such as a hand or foot below the brush or wheels of the Roboking while in use 20 00000000000000000000000000000000000000000000000000000000000 Doing so can cause injury or product damage Do not operate the Roboking on nar row and high furniture such as a ward robe refrigerator desk table etc 20 00000000000000000000000000000000000000000000000000000000000 Doing so can cause injury or product failure N CAUTION Frequently empty the dust bin and secosocsoosococococococccosoccsocsocsoocooscoccoocococosoosooosooooo The dust collected in the dust bin can trigger allergies and may contain harmful insects Use the Roboking indoors only 2000000000020000000000000000000000000000000000000000000000000500 Using it outdoors can cause prod uct failure The Roboking may bump into fur niture such as chair legs table legs J thin and long furniture etc whil
15. attery charge will be shown p e While waiting for timer cleaning the l 2 Co reservation time will be shown timer battery D Cr Battery icon e Lights when the remaining charge is displayed on the battery charge remaining Timer icon section and will flash e This indicates when when charging is required timer cleaning has been set up Tip Use the remote control to change the cleaning mode e Once the cleaning mode has been selected it will be memorised and automatically selected when the unit is turned on again unit it is changed again e To cancel the timer setting press the STOP button on the remote control or the START STOP button on the HOM BOT BEFORE YOU START CD lt these items before cleaning e Do not use this device in a room where a child is left alone The child could be injured Remove fragile or unnecessary objects from the room to be cleaned Especially remove expensive ceramics and valuables from the floor Remove any moisture that might be on the floor e Remove cables strips towels socks etc from the floor so they will not get caught by the brush e Confirm whether battery charge is sufficient and if it is low recharge it e Empty the dust bin if it is full e Close the doors of any room that you do not want the HOM BOT to enter During cleaning the HOM BOT may enter another room and continue cleaning he remote control battery 1 Open the battery cover by lifting the rear hoo
16. dle Charging is required Under charging Check 1 If the battery is not charging even when the HOM BOT is at tached to the home station check the following items Turn the power switch on the bottom of the HOM BOT off once and then on again Unplug and plug in the power plug on the home station Wipe the terminal on the home station with a dry cloth Check 2 If the battery is still not charging after the previous check try the following Attach the HOM BOT to the home station Press the reset button at the rear of the home station for three seconds CLEANING MODES After the zigzag cleaning process is completed the spaces are divided into rectangles and the whole apartment surface is cleaned in detail 1 Press the ZIGZAG Cell by cell button on the remote control 2 HOM BOT cleans to the left until it meets the wall or it cleans over a distance of up to 3 meters 3 After cleaning to the left the HOM BOT goes back to the starting position and begins cleaning to the right If HOM BOT meets the wall or cleans over a distance of 3 meters for a total of 6 meters the zigzag cleaning is completed 4 The cleaning mode is switched to the space expansion mode self cleaning and the cleaning is enabled The Ist stage The maximum outline of 3m x 3m of cleaning area will be cleaned The size of outline will be changed in accordance with the shape of the house inside The 2nd stage
17. e operating 2 220202000000000000000000000000000000000000000000000000000000000000 For a quicker and cleaner performance place the chairs on top of the table Turn the power supply off immediately if any abnormal sound odor or smoke is generated from the Roboking 22020000000000000000000000000000000000000000000000000000000000060 Failure to do so can cause fire or product failure Do not operate the Roboking in a room where a child is sleeping seccecoooocooooococococococosooocoocoocooococooocoooooooooooooooo Doing so can cause injury or product dam age Do not let children play with the Roboking 200000000000000000000000000000000000000000000000000000000000000 Doing so can cause injury or product dam age Do not drop the Roboking or sub ject it to strong impacts 0 02000000000000000000000000000000000000000000000000000000000000 Doing so can cause injury or product failure Do not expose the Roboking to cold temperatures less than 23 F or 5 C for a long period of time 2222020 0002000000000000000000000000000000000000000000000000000000 Doing so can cause product failure Cleaning will not proceed smoothly on carpets with tassels or carpets thicker than 10 mm CeCe ee eresoeererereeeeerereeerELEesEeeEEDEE SEES ELE ESET E EEE E EEE EEe It may be more convenient to arrange them before using the product SAFETY PRECAUTIONS qD N CAUTION In rare cases the HOM
18. ed service person HOW TO TURN THE HOM BOT POWER SUPPLY ON amp OFF To turn the power supply on turn the HOM BOT upside down on a smooth soft surface and check whether the main power supply switch is turned on If the main power supply switch is turned off turn on the switch When turning on the power switch do not press the button located at the upper section of the HOM BOT Operation of the button can be delayed x Turn off the power switch if the HOM BOT will not be used for a long period of time in order to protect the battery x The power switch cover is used for protecting the switch from the dust Always keep the cover attached When the HOM BOT is not at the Home Station and is in the Stand by mode press the START STOP button for more than 1 second The HOM BOT will be turned on and a melody will be sounded x If the power is turned on while the HOM BOT is not at the Home Station and nothing is done for ten minutes the power supply will automatically turn off to reduce battery consumption Press the START STOP button for two seconds while the HOM BOT is turned on A melody will sound when the power is turned off Tip e The power can be turned off due to the static electricity during the operation If the power is turned off turn off the main power switch and then turn it back on e f the power cannot be turned on do the following Turn on the power switch and wait for more than 3 seconds
19. fore the complete discharge of the battery It can take up to three hours to charge the battery Use cleaning methods and auxiliary functions page 18 20 i With remote controller auxiliary function can be used For auxiliary functions manual cleaning spot timer function OVERVIEW HOW TO INSTALL THE HOME STATION 1 Position the home station against a wall to prevent sliding dur ing docking on hard level flooring Remove objects within 1 5m to the right and left side and within 2m to the front Z Z fy yy J 4 VILLI bd SSLSLLLLLLLLL O X 2 Plug the power cord into an outlet Wrap the power cord around the fixed hanger on the back side of the home station or along the wall surface so that the travel path of the HOM BOT will not be obstructed Fixing groove of power cord 3 Fix the home station against the wall so that it does not move ONAR RR VEN Mh hha Tip e Always keep the home station plugged in If the home station is not plugged in the HOM BOT will not return to the station to charge automatically e Since the HOM BOT cleans along the wall if the charging station is installed on the straight surface of the wall you can get a more efficient cleaning e Do not operate the Home Station if it has a damaged cord or plug if it is not working properly or if it has been damaged or dropped To avoid any electrical hazard the cord must be replaced by LG Electronics or a qualifi
20. is actually fitted the unit will not operate without the dust bin gt If the dust bin cover opened close the cover before operating the unit When remaining amount of battery is almost nil the voice Battery is low is generated e Initiate battery charging of HOM BOT by moving it to the home station gt When attaching the HOM BOT to the home station by matching both arrows of HOM BOT and home station charging will be started and the sound of charging start melody will be heard TROUBLESHOOTING When the Roboking detects that the brush is not functioning properly you will hear the message Please check the brush Lay a smooth cloth on the floor overturn the Roboking and place it on the cloth e The side brush is stuck b Remove any foreign materials such as cables thread or hair caught in the side brush or the brush Separation groove of brush Proper assembly assures that the rota tion of the brush becomes smooth e The brush is making a loud abnormal sound b Remove the brush from the Roboking and remove any foreign material from the brush Separation groove of brush For a more detailed description of this process refer to the instructions on page 24 BEFORE YOU CALL FOR SERVICE nD Confirm before reporting the failure of HOM BOT The HOM BOT will not gt Confirm that the power switch is turned on page 14 activate gt Confirm that the battery has been
21. k of the remote control 2 Insert two AAA batteries checking for nodes while loading 3 Close the battery cover completely so that the batteries will not fall out autions while using the remote control e Only press one button at a time e Do not drop or subject it to forceful impact e Do not store it near devices that give off heat fire or hot air e Certain fluorescent lamps such as 3 wavelength fluorescent lamps can interfere with the activation of the remote control Therefore use it as far away as possible from such lamps e If the remote control is too far from the HOM BOT when operated it may fail to operate properly Use the device within 3 m 9 84 ft of the HOM BOT if possible Install the home station page 13 7 Insert the power cord plug into an outlet and locate the station against a wall If power is not supplied to the home station the HOM BOT will not charge Turn on the power supply of the HOM BOT page 14 P Turn on the power switch located on the bottom of the HOM BOT and press the upper START STOP button to turn on the power supply If the power supply is not turned on refer to page 14 Start cleaning page 15 3 Press the START STOP button once again while the HOM BOT is turned on You will hear the sound of cleaning and cleaning will begin Automatic charge page 16 17 4 The HOM BOT will self diagnose and automatically return to the home station to recharge be
22. lter handle should face upward Tip In order to maintain the performance of the HOM BOT the HEPA filter should be cleaned with a cleaning brush or vacuum cleaner at least once a week and should be washed under running water at least once a month CLEANING THE BRUSH CD The brush located on the bottom of the HOM BOT helps with the suction of foreign objects Perform the fol lowing steps to clean the brush Lay a smooth cloth on the floor Separate the cover by press Wearing gloves turn the brush Turn the HOM BOT over and ing the fixing hook and pulling until the separation groove of put the HOM BOT on the cloth upward the brush appears Turn off the power switch before cleaning Separation Grab the brush and remove by Clean the brush with a vacu Insert the fixing hook on the pulling it up um cleaner scissors etc side of the brush marked with the square by matching it to the fixing groove of the brush Insert the fixing hook on the op 3 Align the cover with the O Close the cover by pressing posite side of the brush marked fixing guides on the edge it down until you hear a click with a rounded rectangle by by matching it to the fixing from the fixing hook matching it to the separation groove located on the main 0 NOTE Please make sure that groove of the brush frame the side rotating brushes are not caught under the cover when refitting CLEANING THE
23. ot place the home station and Always use a dedicated outlet imelekoknanesrahcsnoadac zka Me ZE If multiple appliances are connected to an outlet simultaneously they can generate enough heat to cause a fire Core erecccccseeseccrreeresreeseresereseeesereseeeneseeeereeeeeeeLeE fire or product failure Do not force the power plug to bend When pulling out the power plug always Do not use the power plug when it pull it out by grabbing the plug not the cord When pulling out the power plug do not to touch the prongs with your fingers 22200000000000000000000000000000000000000000000000000000000000 Doing so can cause an electric shock esoeoocsocosocoooooooocoooooosseoocoocooooooosocooooooooooooooooo Doing so can cause fire or product failure Do not use the Roboking while a child or object is on it Do not use the Roboking while an object is hanging from it 22020002000000000000000000000000000000000000000000000000000000000 Doing so can cause injury or product dam age Do not touch the power plug with eooeocoooooeeooeoooeOoooOoeOOOOOOOOCOOCOOCROOOOCLCOOOCOCCO 1 Place the cords from other appliances out of the area to be cleaned 2 Do not operate the vacuum in a room where an infant or child is sleeping 3 Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor to be cleaned 4 Do not operate the vacuum in a room that has lit candles on furniture th
24. the TIMER button Each time the button is pressed the time will increase to 2 hours 6 hours and 12 hours 12 12 ET BI I N MI 2 hour 6 hours 12 hours 3 After setting up the start time press the START STOP button on the HOM BOT or wait about five seconds When the timer setting is complete a melody will sound and the timer indicator will remain on Tip e When the set up time is being elapsed cleaning will be started automatically e Use the timer setting when the HOM BOT is attached to the home station If the timer is set up when the HOM BOT is detached from the home station the cleaning time may not be accurate e To cancel the timer setting during the set up time press the STOP button on the remote control or the START STOP button on the HOM BOT e When Roboking is detached from the home station the timer setting will automatically be canceled CLEANING THE DUST BIN GD If the dust bin is full suction power can be weakened Clean the dust bin before and after each cleaning ses sion Clean the dust bin using the following sequence 1 Open the dust bin cover by pressing the PUSH button on the HOM BOT 2 Grab the handle of the dust bin and pull it upward 3 Separate the HEPA filter and the inside sponge filter by removing the HEPA filter gt To clean the dust bin filter refer to page 23 4 Lift the cover upward while pressing the separation button on the dust bin 5 Empty the dust bin
25. tion 14 How to Turn the Power Supply On and Off 15 How to Start and Stop Cleaning 16 17 How to Charge the Battery 18 Cleaning Modes 19 Auxiliary Cleaning Modes 3 CARE AND MAINTENANCE 21 Cleaning the Dust Bin 22 Cleaning the Dust Bin Filter 23 Cleaning the Brush 24 Cleaning the Sensor Charging Terminal 25 Cleaning the Side Brush SAFETY PRECAUTIONS CD The purpose of the safety precautions described below is for the user to use the product safely and correctly to prevent any unexpected risk or damage Basic safety precautions After reading this manual please keep it in an easily accessible location AN This is the safety alert symbol This symbol alerts you to potential hazards that can result in prop erty damage and or serious bodily harm or death AN WARNING indicates a hazardous situation which if not avoided could result in death or serious injury AN CAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury N WARNING This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowl edge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance If the supply cord is damaged it must be replaced by LG Electronics
26. ush may bend or become damaged In this case use the following method to straighten the side brush 1 The following procedure is helpful in restoring de formed brushes 2 Turn off the power supply by pressing the START STOP button on the HOM BOT for two seconds 3 Place the HOM BOT at the end of a table to make cleaning the side brush easier Make sure that the HOM BOT is not in danger of falling 4 Soak the side brush in warm water 5 Press down on the side brush for about ten seconds so that it is completely submerged in the water 6 Slowly wipe the side brush by sliding it through your hand f Rotate the side brush and repeat steps 4 6 for each section of the brush 8 Use the side brush only after it has completely dried TROUBLESHOOTING CD If the unit becomes stuck or suspended and the wheels do not allow the unit move the voice Please check the wheels will be announced e ls a wheel trapped in the front door balcony stairway etc gt Move the HOM BOT on to the flat floor e s any foreign material wound around the wheel gt Lay smooth cloth on the floor overturn the HOM BOT and put it on the cloth Remove foreign material by confirming the wheel TROUBLESHOOTING D When an abnormality is detected with the dust bin the voice Please check the dust bin is announced e Is the dust bin fitted correctly gt Open the dust bin cover and if check if the dust bin
27. xpensive ceramics and valuables from the floor e Do not use this product in the room where a child is sleeping alone The child can be hurt e Confirm whether the battery has sufficient power and if it is low recharge it e Empty the dust bin after if fills up e Close the doors of any room that you do not want the HOM BOT to enter During cleaning the HOM BOT may enter another room and continue cleaning e Remove any moisture from the floor before cleaning e Remove any cables or long strings from the floor e Remove cables strips towels socks etc from the floor so they will not get caught by the brush e Cleaning will not proceed smoothly on carpets with tassels or carpets thicker than 8 mm 0 315 in It may be more convenient to remove or rearrange the position of these rugs or carpets before using the product Please note this product is not intended for use in any workshop commercial office garage or outdoor environment It is for internal normal Domestic internal home use only INCLUDED WITH PRODUCT HOM BOT Remote controller Home station gt Figures can be different from actual objects OWNER S MANUAL CLEANING ROBOT Before using please carefully read the Safety Precautions pages to allow for safe operation of the product After reading the operation 9 fe Operation manual GI CZ Brush for cleaning Filter Dry cell for remote controller 2 units of AAA
Download Pdf Manuals
Related Search