HP ProDisplay P201m
Contents
1. NOTE To remove the stand base press inward on the tab in the center of the underside of the stand base and pull the stand base from the stand Attaching the Stand Base 4 Rear Components Figure 2 2 Rear Components Function Connects the AC power cord to the monitor Connects the audio cable to the monitor Connects the DVI D cable to the monitor Component AC Power Connector 2 Audio Connector select models 3 DVI D select models 4 VGA Chapter 2 Setting Up the Monitor Connects the VGA cable to the monitor Connecting the Cables Place the monitor in a convenient well ventilated location near the computer 2 Remove the cable management clip from the stand by pulling outward on the two sides of the clip 1 then lifting the clip off the stand 2 Figure 2 3 Removing the Cable Management Clip 3 Connect a VGA signal cable or DVI D signal cable select models Ey NOTE The monitor is capable of supporting either analog or digital input select models The video mode is determined by the video cable used The monitor will automatically determine which inputs have valid video signals The inputs can be selected by pressing the source button on the front panel or through the On Screen Display OSD feature by pressing the Menu button e analog operation use the VGA signal cable provided Connect the VGA signal cable to the VGA connector on the rear of the monitor2. then recognizes the new mode just as it does a preset mode In addition to the factory preset modes there are at least 10 user modes that can be entered and stored Energy Saver Feature The monitors support a reduced power state The monitor enters the reduced power state if it detects the absence of the horizontal sync signal the vertical sync signal or both horizontal and vertical sync signals Upon detecting the absence of one or both signals the monitor screen is blanked the backlight is turned off and the power light is turned amber When the monitor is in the reduced power state the monitor uses 5 watts of power There is a brief warm up period before the monitor returns to its normal operating mode Refer to the computer manual for instructions on setting energy saver features sometimes called power management features NOTE power saver feature only works when connected to computers that have energy saver features In the monitor s Energy Saver utility you can also program the monitor to enter the reduced power state at a predetermined time When the monitor enters the reduced power state the power light blinks amber Entering User Modes 17
3. 7 ProDisplay LCD Backlit Monitors User Guide 2012 Hewlett Packard Development Company L P The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein This document contains proprietary information that is protected by copyright No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company First Edition November 201 2 Document Part Number 711877 001 About This Guide This guide provides information on monitor features setting up the monitor and technical specifications A WARNING Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life CAUTION set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information fy NOTE Text set off in this manner provides important supplemental information iv About This Guide Table of contents 1 7 _ ainda 1 1 2 Setting Monar 3 Attaching the Stand
4. Base is tina 3 4 G nnecting the Cables a e a 5 Front Panel Controls ie 7 Adj sting the e E E 8 Turningon the E eb E E 8 Removing the Monitor Stand scansnnersnunnbanienedsaduis saonsnsnsnsunnsasieensesawnnndeasnedoass 9 Mounting the E E EE E ES 9 Installing a Cablelock oniinn 11 3 Finding 12 Prod ct SUPPO hte 12 4 Technical SGC gt 13 elo 13 P201 and BAO iti _ 13 14 Preset Display 15 marrer e e a a a E a a S 15 P201 and P201m Models 15 P221 Modelinin nane AE E EEA 15 Entering User Modes a a Ee aS EATE E 17 Energy Saver 17 vi 1 Product Features HP LCD Monitors The LCD liquid crystal display monitors have an active matrix thin film transistor TFT panel The monitor models and features include P191 model 47 cm 18 5 inch diagonal viewable area disp
5. Tilting the Monitor Turning on the Monitor 1 Press the power button on the computer to turn on the computer 2 Press the power button on the front of the monitor to turn on the monitor A CAUTION Burn in image damage may occur on monitors that display the same static image on screen for a prolonged period of time To avoid burn in image damage on the monitor screen you should always activate a screen saver application or turn off the monitor when it is not in use for a prolonged period of time Image retention is a condition that may occur on all LCD screens Monitors with a burned in image not covered under the HP warranty A prolonged period of time is 12 consecutive hours of non use NOTE f pressing the power button has no effect the power button lockout feature may be enabled To disable this feature press and hold the monitor power button for 10 seconds oy NOTE You can disable the power LED in the OSD menu Press the Menu button on the front of the monitor then select Management gt Bezel Power LED gt Off When the monitor is powered on a monitor status message is displayed for five seconds The message shows which input DVI or VGA is the current active signal the status of the auto switch source setting on or off factory default is on the default source signal factory default is VGA the current preset display resolution and the recommended preset display resolution Chapter 2 Settin
6. software from the CD e Using the OSD menu e Downloading software from the Web e Agency regulatory information e Troubleshooting and recommended solutions to common problems Product Support For additional information on using and adjusting your monitor go to http www hp com support Select your country or region select Product Support amp Troubleshooting and then enter your monitor model in the Search window fey NOTE The monitor user guide reference guide and drivers are available at hitp www hp com support If the information provided in the guide or in the HP LCD Monitors Reference Guide does not address your questions you can contact support For U S support go to http www hp com go contactHP For worldwide support go to http welcome hp com country us en wwcontact_us html Here you can Chat online with an HP technician NOTE When support chat is not available in a particular language it is available in English e Find e mail support e Find support telephone numbers Locate an HP service center 12 Chapter 3 Finding More Information 4 Technical Specifications fy NOTE All specifications represent the typical specifications provided by HP s component manufacturers actual performance may vary P191 Model Table 4 1 P191 Specifications Maximum Weight Unpacked Dimensions include stand Height Depth Width 3 2 kg 7 1 Ibs 34 0 cm 13 4 inches 14 3 c
7. 640 x 480 31 47 59 94 2 720 x 400 31 47 70 09 3 800 x 600 37 88 60 32 4 1024 x 768 48 36 60 00 5 1280 x 720 45 00 60 00 6 1280 x 1024 63 98 60 02 7 1366 x 768 48 00 60 00 P201 and P201m Models Table 4 5 Factory Preset Modes Preset Pixel Format Horz Freq kHz Vert Freq Hz 640 x 480 31 469 59 940 2 720 x 400 31 469 70 087 3 800 x 600 37 879 60 317 4 1024 x 768 48 363 60 004 5 1280 720 45 00 59 94 6 1280 x 1024 63 98 60 02 7 1440 x 900 55 93 59 88 8 1600 x 900 60 00 60 00 P221 Model Table 4 6 Factory Preset Modes Preset Pixel Format Horz Freq kHz Vert Freq Hz 640 x 480 31 469 59 940 Preset Display Resolutions 15 Table 4 6 Factory Preset Modes continued 2 720 x 400 31 469 70 087 3 800 x 600 37 879 60 317 4 1024 x 768 48 363 60 004 5 1280 x 720 45 00 60 00 6 1280 x 1024 63 981 60 02 7 1440 x 900 55 935 59 887 8 1600 x 900 60 00 60 00 9 1680 x 1050 65 29 59 954 10 1920 x 1080 67 50 60 00 16 Chapter 4 Technical Specifications Entering User Modes The video controller signal may occasionally call for a mode that is not preset if e You are not using a standard graphics adapter You are not using a preset mode It this occurs you may need to readjust the parameters of the monitor screen by using the on screen display Your changes can be made to any or all of these modes and saved in memory The monitor automatically stores the new setting
8. and the other end to the VGA connector on the computer e DVI digital operation use the DVI D signal cable provided Connect the DVI D signal cable to the DVI connector on the rear of the monitor and the other end to the DVI connector on the computer 4 Connect one end of the provided audio cable to the audio connector on the monitor select models and connect the other end of the cable to an audio output connector on the rear panel of the computer Connecting the Cables 5 5 Connect one end of the power cord to AC power connector on the back of the monitor and the other end to an electrical wall outlet Figure 2 4 Connecting the Cables 0 4 4 g Z WARNING reduce the risk of electric shock or damage to the equipment Do not disable the power cord grounding plug The grounding plug is an important safety feature Plug the power cord into a grounded earthed electrical outlet that is easily accessible at all times Disconnect power from the equipment by unplugging the power cord from the electrical outlet For your safety do not place anything on power cords or cables Arrange them so that no one may accidentally step on or trip over them Do not pull on a cord or cable When unplugging from the electrical outlet grasp the cord by the plug 6 Secure the cables place with the cable management clip Press the clip straight down on the stand ensuring that the tabs on the sides of th
9. e clip snap into the slots on the stand Figure 2 5 Installing the Cable Management Clip 6 Chapter 2 Setting Up the Monitor Front Panel Controls Figure 2 6 Monitor Front Panel Controls Table 2 1 Monitor Front Panel Controls Control Function 1 2 Menu Opens selects or exits the OSD menu 2 If the OSD menu press to navigate backward through the OSD menu and decrease adjustment levels or If the OSD menu is inactive press to activate volume Minus volume adjustment bar Press or to adjust the volume select d P201m models 3 Plus source If the OSD menu is on press to navigate forward through the OSD menu and increase adjustment levels If the OSD menu is inactive press to activate the source button that chooses the video signal input VGA or DVI 4 OK OK auto If the OSD menu is on press to select the highlighted menu item If the OSD menu is inactive press to activate the auto adjustment feature to optimize the screen image 5 1 Turns the monitor off 6 Power LED White Fully powered Amber Sleep mode Flashing Amber Sleep Timer mode Front Panel Controls 7 8 oy NOTE To view an OSD menu simulator visit the HP Customer Self Repair Services Media Library at http www hp com go sml Adjusting the Monitor Tilt the monitor panel forward or backward to set it to a comfortable eye level Figure 2 7
10. emoving the Monitor Stand on 9 A CAUTION This monitor supports the industry standard 100 mm mounting holes To attach a third party mounting solution to the monitor four 4 mm 0 7 pitch and 10 mm long screws are required Longer screws must not be used because they may damage the monitor It is important to verify that the manufacturer s mounting solution is compliant with the VESA standard and is rated to support the weight of the monitor For best performance it is important to use the power and video cables provided with the monitor 2 attach the monitor to a swing arm sold separately insert four 10mm screws through the holes on the swing arm plate and into the mounting holes on the monitor Figure 2 9 Mounting the Monitor To attach the monitor to other mounting fixtures follow the instructions included with the mounting fixture to ensure that the monitor is safely attached 3 Reconnect the cables to the monitor panel 10 Chapter 2 Setting Up the Monitor Installing Cable Lock You can secure the monitor to a fixed object with an optional cable lock available from HP sold separately Figure 2 10 Installing a Cable Lock Installing a Cable Lock 11 3 Finding More Information Refer to the HP LCD Monitors Reference Guide included on CD with your monitor for additional information on e Optimizing monitor performance e Safety and maintenance guidelines e Installing
11. g Up the Monitor The monitor automatically scans the signal inputs for an active input and uses that input for the display If two or more inputs are active the monitor will display the default input source If the default source is not one of the active inputs then the monitor will display the highest ranking priority input in the following order DVI then VGA You can change the default source in the OSD by pressing the front panel Menu button and selecting Source Control gt Default Source Removing the Monitor Stand You can remove the monitor panel from the stand to install the panel on a wall a swing arm or other mounting fixture Z CAUTION Before beginning to disassemble the monitor be sure the monitor is turned off and the power and signal cables are both disconnected 1 Disconnect and remove the signal and power cables from the monitor 2 Lay the monitor face down a flat surface covered by a clean dry cloth 3 Remove the four screws 1 attaching the stand to the monitor and lift the stand 2 off the monitor Figure 2 8 Removing the Screws Attaching the Stand to the Monitor t gmn 0 0 0 0 ip Mounting the Monitor The monitor panel can be attached to a wall swing arm or other mounting fixture Removing the Monitor Stand 9 oy NOTE This apparatus is intended to be supported by UL or CSA Listed wall mount bracket 1 Remove the stand from the monitor Refer to R
12. lay with 1366 x 768 resolution plus full screen support for lower resolutions includes custom scaling for maximum image size while preserving original aspect ratio P201 and P201m models 50 8 cm 20 inch diagonal viewable area display with 1600 x 900 resolution plus fullscreen support for lower resolutions includes custom scaling for maximum image size while preserving original aspect ratio P221 model 55 cm 21 5 inch diagonal viewable area display with 1920 x 1080 resolution plus full screen support for lower resolutions includes custom scaling for maximum image size while preserving original aspect ratio Non glare panel with an LED backlight that consumes less energy than traditional CCFL backlights Wide viewing angle to allow viewing from a sitting or standing position or moving side to side Tilt capability Removable stand for flexible monitor panel mounting solutions Video signal input to support VGA analog with VGA signal cable provided Video signal input to support DVI digital with DVI D signal cable provided select models Integrated speakers and audio cable select models Supports an optional HP Speaker Bar HP Quick Release and HP USB Graphics Adapter Plug and play capability if supported by the operating system Privacy filter slots to insert filters purchased separately to block side screen viewing Security slot provision on rear of monitor for optional cable lock Cable management feature for placement of cables and co
13. m 5 63 inches 44 93 cm 17 69 inches Maximum Graphic Resolution 1366 x 768 60 Hz analog input Optimum Graphic Resolution 1366 x 768 60 Hz analog input Power Source Input Terminal 100 240 VAC 50 60 Hz One VGA connector with cable included Tilt 30 Operating Temperature 0 to 35 32 to 95 F Operating Altitude Up to 16 404 ft above sea level Up to 5 000 m above sea level NOTE For more information go to http www hp com go productbulletin and search for your specific display model to find the model specific QuickSpecs P201 and P201m Models Table 4 2 P201 and P201m Specifications Maximum Weight Unpacked 3 5 kg 7 7 165 Dimensions include stand 35 92 cm 14 14 inches Height a 15 11 5 95 inches Depth 5 48 20 18 98 inches Width Maximum Graphic Resolution 1600 x 900 60 Hz analog input 1600 x 900 60 Hz digital input P191 Model 13 Table 4 2 201 and P201m Specifications continued Optimum Graphic Resolution 1600 x 900 60 Hz analog input 1600 x 900 60 Hz digital input Power Source Input Terminal 100 240 VAC 50 60 Hz One VGA connector with cable included one DVI connector with cable included one audio connector with cable included P201m only Tilt Operating Temperature 25 5 to 35 41 to 95 F Operating Altitude Up to 5 000 m above sea level Up
14. rds On Screen Display OSD adjustments in several languages for easy setup and screen optimization HP Display Assistant for adjusting monitor settings and enabling the theft deterrence feature HDCP copy protection on DVI input Software and documentation CD that includes monitor drivers and product documentation Energy saver feature to meet requirements for reduced power consumption HP LCD Monitors e Energy Star qualified e Safety guidelines certifications and regulatory notices for these products are available in the HP LCD Monitors Reference Guide on the CD included with this monitor 2 Chapter 1 Product Features 2 Setting Up the Monitor To set up the monitor ensure that the power is turned off to the monitor computer system and other attached devices then follow the instructions below Attaching the Stand Base 1 Lift the stand base from the monitor box and set it a flat surface such as a table top 2 Using both hands lift the monitor from its box position the monitor stand over the stand base and press down firmly to lock it in place Be sure the stand base is securely locked in place and adjust the tilt angle to the desired position A CAUTION Do not touch the surface of the LCD panel Pressure on the panel may cause non uniformity of color or disorientation of the liquid crystals If this occurs the screen will not recover to its normal condition Figure 2 1 Attaching the Monitor Stand Base
15. to 16 404 ft above sea level NOTE For more information go to http www hp com go productbulletin and search for your specific display model to find the model specific QuickSpecs P221 Model 14 Table 4 3 P221 Specifications Maximum Weight Unpacked 4 0 kg 8 8 165 Dimensions include stand 37 9 14 92 inches Height E 16 cm 6 3 inches Depth 51 8 20 39 inches Width Maximum Graphic Resolution 1920 x 1080 60 Hz analog input 1920 x 1080 60 Hz digital input Optimum Graphic Resolution 1920 x 1080 60 Hz analog input 1920 x 1080 60 Hz digital input Power Source 100 240 VAC 50 60 Hz Input Terminal One VGA connector with cable included one DVI connector with cable included Tilt 30 Operating Temperature 0 to 35 32 to 95 F Operating Altitude Up to 5 000 m above sea level Up to 16 404 ft above sea level NOTE For more information go to http www hp com go productbulletin and search for your specific display model to find the model specific QuickSpecs Chapter 4 Technical Specifications Preset Display Resolutions The display resolutions listed below are the most commonly used modes and are set as factory defaults This monitor automatically recognizes these preset modes and they will appear properly sized and centered on the screen P191 Model Table 4 4 Factory Preset Modes Preset Pixel Format Horz Freq kHz Vert Freq Hz
Download Pdf Manuals
Related Search