Home
Marantz TT-15S1
Contents
1. b Attach the counter weight to the back of the arm Counter weight pe SUIS lt A e e When using a different cartridge o O Tone arm GI Attach the cartridge so that it is 32mm from the stylus tip c Removethe cartridge cover 32mm d Connect the 4 tone arm wires to their respective terminals on the attached cartridge For the included cartridge Cartridge cover Caution Make sure that the cartridge stylus tip does not touch the turntable etc and that the stylus tip does not get damaged When using a different cartridge refer to the cartridge instruction manual to connect the wires Caution Be careful when connecting the wires as they are thin and break easily It is easy to connect the wires if you use tweezers etc d e ASSEMBLING AND ADJUSTING Lower the lifter lever and rotate the counter weight to balance the tone arm so that it is parallel with the turntable Tone arm bu the balance Lifter lever After finding the balance raise the lifter lever and attach the anti skating adjustment screw Anti skating adjustment screw Stylus pressure adjustment Adjust to the recommended stylus pressure of the cartridge being used When the tone arm is balanced rotate the counter weight in the direction of the arrow using the counter weight 0 point display as a reference point Reference point
2. 33 18g excluding head shell Dimensions Width 440mm x depth 350mm x height 110mm Excluding tone arm Net weight 8 9kg including tone arm motor 13 OTHERS The section describes the care and maintenance tasks that must be performed to optimize the operation of your Marantz equipment E Cleaning external surfaces of equipment The exterior finish of your unit will last indefinitely with proper care and cleaning Never use scouring pads steel wool scourging powders or harsh chemical agents e g lye solution alcohol thinner benzine insecticide or other volatile substances as these wil mar the finish of the equipment Likewise never use cloths containing chemical substances If the equipment gets dirty wipe the external surfaces with a soft lint free cloth If the equipment becomes heavily soiled dilute some neutral detergents suitable for acrylic material dip a soft lint free cloth in the solution and wring the cloth till it is damp wipe the equipment with the damp cloth dry the equipment by wiping it with a dry cloth 14 E Repairs In the unlikely event your TT 15S1 should need adjustment or repairs contact a Marantz Authorized Service Center Their factory trained technicians have the knowledge facilities and access to replacement parts needed for repair and calibration of your turntable After the warranty period has expired repairs will be performed for a cha
3. good quality record cleaner e Install the turntable chassis and turntable so that they are level It is possible to adjust the height of the legs by rotating them However as there are only 3 legs the height may not be adjustable in some cases In such cases adjust the rack itself so that it is horizontal e About howling and hum Howling occurs when sound from the speaker or vibration is transmitted to the player and is picked up by the cartridge again If howling occurs when the volume is increased check the positions of the speakers and turntable and move them to locations where neither vibration nor sound is transmitted to the turntable Hum noise occurs because of electromagnetic waves that are generated from other electronic devices Check the position of other electronic devices that are near to the turntable especially the amplifier Also hum or noise occurs if the ground is not connected correctly Check that the ground wire is securely connected to the GND terminal on the amp mixer ACCESSORIES Before using the turntable please make sure that you have all of the following accessories 1 Turntable chassis 5 Motor 2 Center shaft 6 Motor pulley for 60Hz areas 3 Tone arm 7 Gloves pair 4 Turntable 8 Ground wire ACCESSORIES 9 2 Drive belts 1 spare belt 13 Record clamp Clever clamp produced by Southern Engineering 10 Bearing oil 14 Counter weight 11 Turntable
4. MC to suit the attached cartridge If you are using the included cartridge set to MM 3 Seta record on the turntable If you are playing an EP record use a commercially available EP adapter 4 Attach the belt to the motor pulley in the correct position for the chosen record 5 Switch the power button ON The turntable will begin to rotate at the speed selected in operation 4 above Caution In order to reduce noise the motor torque has been set to the minimum level in this turntable Therefore the turntable sometimes does not rotate when the power is switched on If this happens gently rotate the turntable a little in the clockwise direction by hand 6 f Amplifier marantz Lift the lifter lever then use the head shell finger hook to move the tonearm to the play position of the record Lower the lifter lever The tonearm slowly lowers the stylus onto the record and the record starts to play Caution e Do not allow the turntable to be jolted or vibrated while playing a record e Always stop the turntable when changing records e Always turn down the amplifier volume when placing the stylus on or removing it from the record MW When the record has finished 1 Gently raise the lifter lever The tone arm raises and the stylus separates from the record Return the tone arm to the arm rest using the head shell finger hook Lock the tone arm in the arm rest Switch
5. C SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 ST POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la Classe B est conforme a la norme NMB 003 du Canada CONTENTS CONTENT rita iii 1 BEFORE USE a 2 RTE 3 ASSEMBLING AND ADIUS ING ln 5 NAMES AND FUNCTIONS re 10 CONNECTIONS AND OPERATION ssp 11 TROUBLE INE 12 SPECIFICATIONS AND EXTERNAL DIMENSIONS DIAGRAM i rvvvnnvnnvnvvvvvvvvvvvvvvnnnvnnnnrrrrrrrnnnnnnnnnnnnnnn 13 OT E 14 BEFORE USE This section must be read before any connection is made to the mains supply E Equipment Main Power Setting Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area TT 15S1 can be powered by 120V AC only E Copyright Recording and playback of any material may require consent For further information refer to the following Copyright Act 1956 Dramatic and Musical Performers Act 1958 Performers Protection Acts 1963 and 1972 Any subsequent statutory enactments and orders E Do Not Locate in the Following Places To ensure long lasting use do not locate the TT 15S1 where e Exposed to direct sunlight e Near to sources of heat such as heaters e Highly humid or poorly ventilated e Dusty Subjected to mechanical vibrations e On wobbly inclin
6. PLUG Mains Cord Protection Mains cord should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product Protective Attachment Plug The product is equipped with an attachment plug having overload protection This is a safety feature See Instruction Manual for replacement or resetting of protective device If replacement of the plug is required be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode See Figure 1 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the a
7. Rotating the counter weight by 1 scale graduation adds 0 1g of pressure Therefore as the counter weight has 5 graduations one complete turn will add 0 5g of pressure As the recommended stylus pressure for the included cartridge is 2 2g rotate the counter weight 4 complete turns and 2 scale graduations from the reference point at balance adjustment to reach the correct stylus pressure position Rotate 4 complete turns and 2 graduation points from the reference point Counter weight l Stylus pressure 2 2g When using a different stylus check the recommended stylus pressure and adjust to the correct stylus pressure Anti skating adjustment Adjust the anti skating adjustment screw in line with the stylus pressure of the cartridge being used For the included cartridge adjust so that the screw position is approximately half way out _ Screw half way position Anti skating adjustment screws ASSEMBLING AND ADJUSTING 9 Attaching the motor pulley Attach the motor pulley to the motor Using the adjustment screwdriver included to fix the pulley s 3 plastic screws Be careful not to turn the screws with too much force as they are made from plastic and can break easily Included screwdriver for adjustment When attaching the pulley fix with approximately 3mm space between the pulley and motor 3mm 10 Installing the motor From underneath the turntable chassis plac
8. being played a certain amount of force is exerted on the stylus that pulls it towards the center This knob is used to perform adjustments that cancel out that force Counter weight This is used to balance the toner arm and to adjust the stylus pressure 1 Record clamp This is effective in holding the record when records are being played without a turntable sheet or when playing warped records Use it as shown in the diagram CONNECTIONS AND OPERATION TT 15S1 E Connections Make sure that the power supply to both this turntable and the amplifier are OFF before you start connecting 1 Connect the PHONO cables L white R red that are connected to the toner arm to the corresponding L and R PHONO input terminals on your amplifier 2 Connect both the ground wire that is connected to the bottom of the turntable and GND cable that is connected to the toner arm to the GND terminal ground terminal on your amplifier 3 Plug the motor power cord into an AC 120V outlet Caution If your amplifier etc has power outlets on the back panel plug the turntable into one of these outlets In this case refer to the instruction manual for amplifier etc and check that the power outlet has enough power capacity E Operation HM Starting to play records 1 Plug the turntable power cable into an AC outlet 2 Turn on the amplifier and select input to PHONO Also set the amplifier phono equalizer to either MM or
9. d used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by tuning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures NOTE TO CATV SYSTEM INSTALLER Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help NOTE Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This reminder is provided to call the CATV Cable TV system installer s attention to Section 820 40 of the NEC which provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards There are however some installation and operation precautions which y
10. e the motor in the hole section at the back left of the turntable chassis Do not fix it to the turntable base DI e 3 q E tr a Z SS Caution When installing the motor in order to prevent motor vibrations from being transmitted to the turntable base install the motor so that it does not touch the base 11 Installing the belt Use one of the belts included and attach it between the motor pulley and turntable When attaching the belt hook it over the central slot There are 2 belts included with the turntable Please keep one as a spare Central slot The positions for attaching the motor pulley belt are different when playing 45 or 33 rpm records Change the position of the belt to suit the record that you want to play Attach to the lower side Attach to the upper side Caution When changing the position of the belt use the gloves included and be careful not to damage the belt in any way NAMES AND FUNCTIONS 1 Power switch OFF ON When it is switched ON the turntable rotates Pulley This is changed to suit the rom speed of the record to be played 33 1 3 rpm record Lower side 45 rpm Fecord Upper side 3 Belt 4 Turntable Turntable sheet 6 Cartridge 7 Tone arm Lifter lever This is used to raise and lower the tone arm 10 O 9 Anti skating knob When a record is
11. ed or otherwise unstable surfaces e Radiated heat is blocked such as in cramped audio racks To ensure proper heat radiation ensure the below clearance from walls and other equipment Front E Caution Do not lose the bearing View from underneath the turntable chassis Turntable chassis Center shaft hole Bearing Center shaft SE There is a bearing located inside the center shaft hole in the turntable chassis When the turntable leaves the factory the center shaft hole is covered with tape to prevent the bearing from falling out Sometimes after removing the tape the bearing falls out when the turntable is turned over If the center shaft is inserted when there is no bearing in the center shaft hole the turntable will not rotate Therefore make sure that the bearing does not fall out of the center shaft hole when assembling the turntable Furthermore if the turntable is disassembled for transportation etc cover the center shaft hole with tape etc to prevent the bearing from falling out E Before using e Thoroughly remove dust or dirt from the stylus point and record If you play records when there is dirt dust on the stylus not only will the stylus have poor contact with the record causing poor sound quality it will also increase the rate of wear of both the stylus and record Gently remove dirt dust by brushing with a soft tipped brush from the base of the stylus to the tip Also wipe the record with a
12. er weight ASSEMBLING AND ADJUSTING b 2 Direction The direction position is correct when the tone arm is parallel with the side of the turntable base Tone arm Based side Of turntable Parallel b 3 When you have determined the height and direction of the tone arm attachment position tighten the tone arm fixing screw using the Allen wrench large Allen wrench large After fixing the tone arm in place remove the counter weight and tone arm height adjustment sheet 5 Attaching the cartridge a Use the Allen wrench medium to remove the head shell from the tone arm Allen wrench medium Tone arm CC S Head shel SCS o Attach the cartridge to the head shell Screw Lal i Q Head shell Cartridge e When attaching the cartridge that was included with the turntable use the aluminum screw and slotted screwdriver that are also included e When attaching a different cartridge choose a cartridge that is compatible with the cartridge weight range for the tone arm Compatible cartridge weight 3 18g ASSEMBLING AND ADJUSTING c Attach the cartridge that you attached in the previous 6 Adjusting arm balance step to the tone arm a Remove the anti skating adjustment screw EE 4 Tone arm Head shell Anti skating adjustment screw e When using the included cartridge Attach to the front attachment hole position on the tone arm
13. he head shell fixed securely with the lock nut The stylus jumps e Is the stylus pressure adjusted to the correct stylus pressure e Is the record warped or scratched Is there a lot of dust collected on the stylus The arm stops progressing half way through the record e Is the record scratched Is there something touching the arm The sound is too quiet Or too loud e Is the amplifier connection switching suitable for the type of cartridge being used MC MM SPECIFICATIONS AND EXTERNAL DIMENSIONS DIAGRAM 350 110 350 E Turntable section E Included Cartridge Clearaudio REN an 33 1 3 rpm 45 rpm Frequency response 20Hz 20 kHz Drive SYStem ii Belt drive system Output voltage 1kHz 5CM S 3 6 mV UI Ce sec snarere High density acrylic Channel separation gt 30 dB Turntable depth 28 mm Channel balanNCe lt 0 2 dB RPM deviation EU Yo Recommended stylus preSSUure 2 29 SN 80 dB ITI DCO Ein et 0 66 kQ nl Aluminum Cartridge weight 6 09 E Tone Arm section ge asco 2 point radial tone arm E General Specifications Effective Jengi 239mm OVE E EEE ENE 17mm Power SUpplY AC120V 60 Hz Stylus pressure adjustable range 0 5g 1 Graduation 0 19 Power consumption 5W Compatible cartridge weight
14. marantz Model TT 15S1 User Guide EE Turntable RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AN A WARNING The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOC ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed an
15. ntenna or cable system This will prevent damage to the product due to lightning and power line surges Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 20 Sch Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions When the Mains cord or plug is damaged If liquid has been spilled or objects have fallen into the product If the product has been exposed to rain or water If the product does not operate normally by following the opera
16. ou should be particularly aware of 1 10 11 Read Instructions All the safety and operating instructions should be read before the product is operated Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the product and in the operating instructions should be adhered to Follow Instructions All operating and use instructions should be followed Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer A product and cart combination should be moved with care Quick stops excessive force and uneven s
17. rge if the equipment can be returned to normal operation In the event of difficulty refer to your Marantz Authorized Dealer or Marantz Authorized Service Center If writing please include the model and serial number of the equipment together with a full description of what you think is abnormal about the equipment s behaviour You can find your Marantz Authorized Dealer or Service Center on our website www marantz com Approximately every two years you can lubricate only if you will recognize speed variations the bearing of the center shaft with the delivered oil In this case it is enough to put 4 or 5 drops into the center shaft hole in the turntable chassis Be careful not to add too much oil www marantz com You can find your nearest Marantz Authorized Dealer on our website U S A Marantz America Inc 1100 Maplewood Drive Itasca IL 60143 U S A marani Z is a registered trademark Printed in USA 11 2005 00M31BW851250 mzh d
18. sheet 15 Tone arm height adjustment sheet gt 12 3 Allen wrenches large medium small 1 adjustment screwdriver 16 Cartridge MM type by Clearaudio JR 1 2 3 ASSEMBLING AND ADJUSTING Installing the ground wire Connect the ground wire to the turntable shaft base Turntable shaft base Ground wire Inserting the center shaft Insert the center shaft into the turntable chassis O shaft Turntable chassis Installing the turntable Place the turntable onto the center shaft Turntable Center shaft 4 Attaching the tone arm a Pass the Phono cable that is connected to the tone arm through the tone arm attachment hole a Tone arm gt np sd ON I A D cable ES Np Turntable chassis O b Determine the height and direction of the tone arm attachment position b 1 Height Bear in mind that the height position of the tone arm is different depending on whether or not the turntable sheet is used e When using the turntable sheet The correct height position is achieved when the counter weight and tone arm height adjustment sheet are placed beneath the arm lifter With turntable sheet Counter weight Tone arm height adjustment sheet e When not using the turntable sheet The correct height position is achieved when just the counter weight is placed beneath the arm lifter Tone arm height adjustment sheet is not used No turntable sheet Count
19. the power button OFF The turntable stops rotating 11 TROUBLE SHOOTING If you think a malfunction has occurred first check the points listed below MW Are each of the connections correct HM Are you operating the turntable correctly as described in this instruction manual If the turntable does not operate correctly check all of the items in the following table However if none of the items in the following table correspond to the problem it is possible there is a fault with your turntable In this case turn off the power un plug the power cord from the AC outlet and contact your dealer If you do not remember where you bought this turntable contact the Marantz Authorized Service Center HM About the included cartridge You cannot replace the stylus in the cartridge that is included with this turntable If you wish to exchange the cartridge itself contact the Marantz Authorized Dealer 12 E Check Items The stylus won t lower onto the record e Is the tone arm height adjusted correctly e Is the stylus pressure adjusted correctly e Is the arm balanced correctly There is no sound e Are the cartridge and head shell connected correctly Is the output cord connected to the amplifier correctly Are the amplifier knobs adjusted and switched correctly A humming noise is emitted e Is the output cord ground wire connected to the amplifier e Is the output cord plug connected securely e Is t
20. ting instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation If the product has been dropped or damaged in any way and When the product exhibits a distinct change in performance this indicates a need for service 22 23 24 25 FIGURE 1 EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANSI NFPA 70 GROUND CLAMP TA ELECTRIC SERVICE EQUIPMENT GROUND CLAMPS L A gt I Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat N ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT NE
21. urfaces may cause the product and cart combination to overturn UA AS A Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions le 13 14 19 16 14 18 19 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug AC POLARIZED
Download Pdf Manuals
Related Search
Related Contents
Bedienungsanleitung (Invitaci\363n Saint George - Ser Pap\341s-2) Chapter 1 - Aerotech Air Max - Support-acteon IP Appliance Spec Pioneer U310 Installation Guide Introducción 1 - Thermo Fisher Scientific the CrestDiag® Manual Copyright © All rights reserved.
Failed to retrieve file