3M MP225
Contents
1. 800x600 60Hz The projector does not support the video signal signal ba The projector is measuring and synchronizing to video input 2012 3M All Rights Reserved 19 3M Mobile Projector 225 Adjusting Image Size The 3M MP225 Projector can project a diagonal image of 10 to 80 inches 254 2032 mm Refer to the chart for associated dimensions Image Size Diagonal Width Height Distance 10 in 25 4 cm 8 in 20 3 cm 6 in 15 2 cm 12 in 30 5 cm 14 in 35 56 cm 11 1 4 28 4cm 83 8 in 21 3 cm 16 3 4 in 42 7 cm 20 in 50 8 cm 16 in 40 6 cm 12 in 30 5 cm 24 in 61 cm 26 in 66 04 cm 20 3 4 52 8 15 5 8 in 39 6 cm 31 2 8 in 79 2 cm 32 in 81 28 cm 25 5 8 in 65 cm 19 1 4 in 48 8 cm 38 3 8 in 97 5 cm 38 in 96 52 cm 30 3 8in 77 2cm 22 3 4 in 57 9 cm 45 5 8 in 115 8 cm 44in 111 76cm 35 1 4 89 4 263 8 in 67 1 cm 53 134 1 cm 50 in 127 40 101 6 cm 30 76 2 60 in 152 4 cm 60 in 152 4cm 48 in 121 9 cm 36 in 91 4 cm 72 in 182 9 cm 70 in 177 8 cm 56 in 142 2 cm 42 in 106 7 cm 84 in 213 4 cm 80 in 203 2 cm 64 in 162 6 cm 48 in 121 9 cm 96 in 243 8 cm Important Note As you increase the size of the projected image you will need to decrease darken the ambient room lighting Adjusting the Focus Turn the focus wheel to sharpen the image 20 2012 3M All Rights Reserved 3M2. Mobile Projector MP225 Adjusting the Volume Press the Volume Up or Volume Down button to adjust the sound A volume bar will appear on the screen to help you set the volume level Muting the Volume Press the MUTE button to mute the volume An icon will appear on the screen to indicate the current setting To restore the volume press the MUTE button again If you press the Volume Up or Volume Down button while the volume is muted the volume will also be restored but from an initial volume level of zero Checking the Battery Level To check the battery press the Battery Status button A battery bar will appear on the screen indicating the amount of charge currently in the battery 2012 3M All Rights Reserved 21 3M Mobile Projector 225 Attaching the Tripod Optional Accessory The table top tripod optional accessory mounts to the bottom of the projector Tip The 3M MP225 Projector will attach to most camera tripods Cleaning the Projector 1 Turn off the projector and disconnect power and other cables 2 Use a soft cloth such as the 3M High Performance Cleaning Cloth to wipe off dust If the dust is difficult to remove dampen the cloth with clean water and then wipe the projector clean Then use a clean cloth to dry the projector Important Note Do not use cleaning chemicals or solvents to clean the projector Cleaning chemicals and solvents may cause the plastic parts to di
3. 110 240 VAC 50 60 Hz 2 8 0n Note The battery status will not appear when the power adapter is connected to the projector The power adapter icon will appear instead 12 2012 3M All Rights Reserved 3M Mobile Projector 225 Battery Charging Notes If the projector power is off allow three hours for the battery to fully recharge If the projector power is on the battery will take longer to charge The battery has a lifespan and ages every time it is fully charged and discharged The battery will gradually lose charge capacity as it ages Therefore as the battery ages the battery life will decrease Battery Maintenance Tips Remove the battery when the projector will not be used for one week or longer Charge and discharge the battery by turning on the projector at least once a month When storing the battery for more than a month store it at 50 charge The battery is at 50 charge when the battery icon has three bars Do not store a fully discharged battery because it may lose the ability to be recharged Do not store a fully charged battery because it may lose the ability to be recharged to full power 2012 3M All Rights Reserved 13 3M Mobile Projector 225 Making Connections The 3M Mobile Projector MP225 will display informational icons depending on the input device and signal being detected The 3M MP225 was designed to opera
4. 18 2012 3M All Rights Reserved 3M Mobile Projector MP225 Status Indicator Light The status indicator light provides information about the projector s state Status Indicator Light Meaning A new power source is connected to the projector and the projector is ready to be powered on Projector is off If the power adapter is connected to the Flashes green three times Blank projector and the battery is installed the battery has finished charging Flashes green The projector is starting up Solid green The projector is on Solid amber The projector is off and charging the battery Flashes amber The projector has overheated and needs to cool i and pauses The projector cannot charge the battery The projector cannot turn on because the battery needs to Flashes Red be charged On Screen Icons The projector will display a video icon when it is connected to a video cable or a video source Icon Description Meaning The projector detects the audio video cable The projector detects an NTSC video input signal The projector detects a PAL video input signal The projector detects the component audio video cable The projector detects the video input signal and displays the video source s resolution and refresh rate below the component icon The projector detects the VGA audio cable The projector detects computer input signal and displays the input resolution and refresh rate
5. 8 10 2012 3M All Rights Reserved 3M Mobile Projector MP225 Power Adapter The power adapter is used to charge the battery or power the projector There are four outlet adapters to give you the flexibility to power the 3M MP225 projector in most countries Installing an Outlet Adapter onto the Power Adapter 1 Select the outlet adapter that will plug into your wall outlet 2 Align the outlet adapter to the power adapter and slide the outlet adapter into place pur LQ Replacing the Outlet Adapter 1 Push the button on the outlet adapter 2 Slide the outlet adapter up 3 Remove the outlet adapter 4 Replace with the new outlet adapter 2012 3M All Rights Reserved 11 3M Mobile Projector MP225 Charge the Battery The rechargeable battery gives you up to two hours of battery life When the battery needs to be charged the status indicator will flash red The battery should be fully charged before using the projector Charge the battery by connecting the power adapter to the projector 1 2 3 4 5 Turn the projector power off Connect the power adapter to the projector s DC input Connect the other end of the power adapter into the electrical outlet The status indicator will change to amber while the battery is charging Allow three hours to fully charge the battery When charging is complete the status indicator will turn off
6. To reduce the risks associated with hearing loss Be sure to read earphone manufacturer s instructions with respect to volume level e User is responsible to set a safe volume level To reduce the risk associated with environmental contamination Dispose of all system components in accordance with applicable government regulations To reduce the risks associated with LED bright light e Do not stare directly into the projector lens To reduce the risks associated with tripping and falling Position the charging cord and data cables so that they are not a tripping hazard SAVE THESE INSTRUCTIONS 6 2012 3M All Rights Reserved 3M Mobile Projector MP225 Safety Labels us o WADE LITHIUM ION BATTERY Model No LIN370 002 23Wh 10 95V 2100mAh P N 78 6972 0058 8 Warning Use a specified charger Do not throw the battery into fire or heat Do not short circuit the battery terminals Do not disassemble the battery Charging Specification Standard Charge 12 3V 1 1A Cut Off Voltage 9V Max Charge 12 3V 2 1A LED Light Output CLASS 1 LED 60825 1 1993 A1 Maximum Radiant Power PRODUCT 1997 2 2001 1 693 mW 2012 3M All Rights Reserved 7 Package Contents 1 3M Mobile Projector MP225 2 Rechargeable Battery 3 Outlet Adapters 4 4 Power Adapter 5 Product Warranty and Safety Guide 6 Quick Start Guide 7 AV Cable for Apple Devices 3M Mobile
7. a vehicle Do not carry the battery in pockets purses or handbags where it may contact metal objects Do not place battery in contact with metal objects Do not expose or store battery in direct sunlight or excessive heat gt 60 140 or in moist or caustic environments To reduce the risks associated with driver distraction e Do not use this projector a moving motor vehicle To reduce the risks associated with choking Keep AV adapters and other small parts away from young children 2012 3M All Rights Reserved 5 3M Mobile Projector 225 A Warning To reduce the risk associated with fire and explosion battery leakage or overheating Do not immerse the battery in water or allow it to get wet Do not reverse the positive and negative terminals Do not connect the battery directly to a wall outlet Use only the 3M specified wall charger or automobile charger Do not strike throw or subject the battery to physical shock Do not pierce the battery or break it open Keep batteries out of the reach of children Do not recharge the battery near a heat source or in extremely hot conditions Do not use the battery if it gives off an odor generates heat or becomes discolored or deformed Keep away from exposed flames if the battery leaks or emits an odor Flush the eyes with water and seek medical attention if the battery leaks and battery fluid gets in the eyes Caution
8. the 3M product are subject to individual warranties THE WARRANTIES STATED ABOVE ARE EXCLUSIVE AND ARE MADE IN PLACE OF ANY AND ALL WARRANTIES EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY INDUSTRY PRACTICE OR CUSTOM OR TRADE USAGE In the event the 3M product fails to conform to the above stated warranties within the applicable warranty period your exclusive remedy shall be at 3M s option to replace or repair the 3M product or to refund the purchase price of the 3M product All replaced parts or products become property of 3M If the product is repaired will repair the defective part s with a new or used part s If the product is replaced 3M will replace the 3M product with the same or equivalent model and with a new or refurbished 3M product In the case of an approved warranty claim the replacement 3M product will carry only the remaining term of the original 3M product s warranty period as stated above For warranty service you must provide proof of the date of the original purchase else the manufacturing code date will be used to establish the start date of the warranty The following are exclusions to the above listed warranty a This warranty does not cover 3M product that is modified or damaged through improper storage misuse abuse accident vandalism improper installation neglect improper shipping damage caused by act
9. to a Component Video Device Optional Accessory For component video input you must purchase the optional 3M MP225 Component AV Cable 3M part number 78 6972 0032 3 This cable sends a higher quality video signal for the best possible image 1 Connect the component AV cable to the projector s VGA AV input 2 Connect the other end of the AV cable to the video device s audio and video outputs Important Note There are two red connectors on the Component AV cable One is for the right audio channel and the other is for the Pr component video signal Be careful to connect the red audio to red audio and red video to red video If these connectors are switched the projected image will appear green and an abnormal noise will come from the right speaker Tip Some video devices do not have the standard audio and video connections and may require an AV cable specified by the manufacturer The AV cable allows you to connect your video device to your TV monitor or your projector and may be purchased from the video device manufacturer Once you have the AV cable use the cable adapters to connect the video device cable and the projector cable Some video devices by default will not output a video signal The video device s manual should provide instructions on how to change the video output setting 16 2012 3M All Rights Reserved 3M Mobile Projector MP225 Connecting to a Computer Optional Accessory Use the
10. Icons on page 19 The video output on some devices is turned off by default Please refer to the device s documentation for details on enabling the video output 24 2012 3M All Rights Reserved 3M Mobile Projector MP225 Specifications Projector Description Specification Imager Technology Size Resolution Aspect Ratio Projection Distance Image Size Throw Ratio Diagonal Distance Lens Offset Inputs Compatible Resolutions Vertical Scan Rate Horizontal Scan Rate Video Compatibility Video Resolutions Dimensions Weight Tripod Socket Operating Conditions Temperature Range Humidity Range Altitude Range 2012 3M All Rights Reserved LCOS 9 4 mm 0 37 SVGA 800 x 600 Pixels 43 8 4 in 50 4 in 213 1280 mm 10 in 60 in Diagonal 254 1524 mm 1 0 84 1 1 none DC in AV in inc VGA and component VGA SVGA XGA WXGA 1280 x 960 60Hz 1440 x 900 60Hz MAC 640 x 480 67Hz 832 x 624 75Hz 1152 x 8 0 75Hz 50 Hz 60 Hz MAC 67 Hz 75 Hz 31 5 kHz 49 68kHz NTSC PAL 480i 480p 576i 576p PAL NTSC H 264 SD 4801 5761 720p 1080i 5 91 x 2 56 x 1 20 in 150 x 65 x 30 5 mm lt 11 46 oz s 325 g 20 32 95 F 0 35 C 10 80 RH without condensation Sea Level to 1 829 m 6000 25 3M Mobile Projector 225 LIN370 002 Rechargeable Lithium ion Battery Description Specification Type LI
11. N370 002 Rechargeable Lithium lon Battery Rated Capacity 10 95 V 2100 mAh 23 Wh Dimensions 81 5 x 64 x 23 mm Important Note Do not throw battery into trash Please dispose of it according to federal state or local laws Supported Computer Signals Description Resolution width x height Refresh Rate VGA 640 x 480 60 Hz SVGA 800 x 600 60 Hz XGA 1024 x 768 60 Hz WXGA 1280 x 768 60 Hz 1280 x 960 60Hz 1440 x 900 60Hz MAC 640 x 480 67Hz 832 x 624 75Hz 1152 x 870 75Hz Replacement Parts Accessories Power Adapter with US EU UK AUS plugs 78 6972 0063 8 Lithium lon Battery 78 6972 0058 8 AV Video Cable 78 6972 0031 5 Optional VGA Cable 78 6972 0062 0 Optional Component AV cable 78 6972 0032 3 Optional 3M Adapter Cable for Apple 78 6972 0064 6 26 2012 3M All Rights Reserved 3M Mobile Projector MP225 Limited Warranty This warranty applies to the continental US only The warranty terms conditions remedy and limitation may vary in other countries Contact your local 3M Company for warranty information e The 3M Mobile Projector MP225 the product is warranted to be free from defects in material or manufacture for a period of 1 year from the date of purchase e All other accessories included with the product are warranted to be free rom defects in material or manufacture for a period of 1 year from the date of urchase e B ptional product accessories that are not sold as part of
12. Projector 225 8 2012 3M All Rights Reserved 3M Mobile Projector MP225 Parts Power Button Mute Button Volume Down Button Volume Up Button Battery Status Button Status Indicator eo Focus Wheel Lens co N DO CO Speaker Flip Stand Tripod Socket Battery Battery Latch Sb cc ND c Earphone jack VGA A V Input DC Power Input lt b 2012 3M All Rights Reserved 9 3M Mobile Projector 225 Getting Started Removing the Protective Film When the projector is shipped there is a protective film between the battery and the battery contacts on the projector Remove the protective film by removing the battery and the protective film discard the film and finally install the battery Install Battery The 3M Mobile Projector MP225 comes with a rechargeable battery The battery should be fully charged before using the projector with the battery To install the battery point the contacts on the battery toward the contacts on the projector insert the end farthest from the battery latch first then push down until the battery clicks into place Remove Battery To remove the battery slide the battery latch away from the battery and then lift the battery out starting at the end closest to the latch Important Note Use only the 3M specified battery 78 6972 0058
13. VGA audio cable to connect the projector to desktop computers laptop computers ultra portable computers and some personal digital assistants PDAs The projector supports VGA SVGA XGA and WXGA resolutions For best results set the computer s resolution to SVGA 800x600 1 Connectthe VGA cable to the 3M Mobile Projector MP225 2 Connect the VGA cable to the computer s video and audio outputs 3 Setthe computer resolution to one of the supported resolutions Description Resolution width x Refresh Rate height VGA 640 x 480 60 Hz SVGA 800 x 600 60 Hz XGA 1024 x 768 60 Hz WXGA 1280 x 768 60 Hz 1280 x 960 60Hz 1440 x 900 60Hz MAC 640 x 480 67Hz 832 x 624 75Hz 1152 x 870 75Hz 2012 3M All Rights Reserved 17 3M Mobile Projector 225 Basic Operating Instructions Powering On Press and hold the power button for three seconds Release the power button when the projector begins to project an image and the status indicator turns green rin 09 SOR Tip The video output on some devices is turned off by default Please refer to the device s documentation for details on enabling the video output Powering Off Press and hold the power button for three seconds Release the power button when the projected image is gone The projector is off when the status indicator is off or solid amber When the status indicator is solid amber the battery is charging
14. ct Customer Service at 1 866 631 1656 or email meetings mmm com What 3M Will Do To Correct Problems e f your 3M product requires service will ask you to bring or send the 3M product securely packaged in its original container or equivalent along with proof of the date of original purchase to your 3M Service Dealer or 3M Service Center 3M will at its option repair or replace the defective unit without charge for parts or labor Return of the 3M product will be at 3M s expense e When warranty service involves the exchange of the product or of a part the item replaced becomes 3M property 28 2012 3M All Rights Reserved 3M Mobile Projector MP225 e The exchanged product or part may be new or previously refurbished to the 3M standard of quality and at 3M s option the replacement may be another model of like kind and quality liability for replacement of the warranted product or part will not exceed the original retail selling price of the 3M product Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty FCC STATEMENT CLASS B This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class B co
15. for future reference Explanation of Signal Word Consequences A Warning Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and or property damage Caution Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury and or property damage Warning Hazardous voltage 4 2012 3M All Rights Reserved 3M Mobile Projector MP225 Warning To reduce the risk associated with hazardous voltage e Do not modify this product in any way Use only approved replacement components e Do not attempt to service this projector other than battery replacement There are no user serviceable parts other than the battery Service to be performed only by a 3M authorized service provider using 3M approved system components Do not use the wall power supply in a wet environment Do not use with a damaged wall power supply Replace damaged part prior to use To reduce the risk associated with fire and explosion e Do immerse the projector or battery in any liquid or allow either to get wet Use only 3M approved power supply and lithium ion battery provided Do not disassemble or short circuit the battery Do not dispose of the battery by incineration or fire Do not operate this projector in any environment above 35 C 95 F Do not expose the projector or battery to direct sunlight in a closed space such as
16. gdom Patent No 2417360 and other U S and international patents pending owned by Syndiant Inc 30 2012 3M All Rights Reserved 3M Mobile Projector MP225 2012 3M All Rights Reserved 31 3M is a trademark of 3M Company Mobile Interactive Solutions 3M Austin Center 6801 River Place Blvd Austin TX 78726 9000 866 631 1656 www 3MPocketProjector com 3M 2012 All Rights Reserved meetings mmm com 78 6971 1627 1
17. ma projector operators guide 3M Mobile Projector 225 2 2012 3M All Rights Reserved 3M Mobile Projector MP225 Contents Intended Use Statement sss 4 nae 4 odlelyEabelS ret he 7 Package COMMS ht Fore P etes 8 sten ion 9 Getting SAN TTE 10 Making Connections 14 Basic Operating Instructions 2 18 Cleaning Ahe ProjeCtOr s c 22 Troubleshooting sss 23 0261122102 rr 25 Limited Warranty 27 2012 3M All Rights Reserved 3 3M Mobile Projector 225 Intended Use Statement The 3M Mobile Projector MP225 is designed to operate with the 3M specified battery and 3M power adapter in normal office or home environments e 0 350 32 0951 10 80 RH without condensation e 0 1829 0 6000 feet above sea level The ambient operating environment should be free of airborne smoke grease oil and other contaminants that can affect the operation or performance of the projector Use of this product in adverse conditions will void the product warranty Safety Information Please read understand and follow all safety information contained in these instructions prior to the use of this projector Retain these instructions
18. moved unless otherwise stated in writing for the purposes of private labeling for partnership requirements i This warranty does not cover postage insurance or shipping costs incurred in presenting your 3M product for warranty service Said costs are the customer s responsibility If a claimed defect cannot be identified or reproduced in service the customer may be held responsible for cost incurred Should your warranty upgrade include a change out service and the claimed defect cannot be identified or reproduced by the technician the customer will be responsible for call out costs FAILURE TO FOLLOW THE INSTRUCTIONS CONTAINED IN THE APPROPRIATE 3M PRODUCT MANUAL OR TO USE THE 3M PRODUCT IN ACCORDANCE WITH 3M S INTENDED USE STATEMENT WILL VOID ALL WARRANTIES AND LIMITED REMEDIES EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL 3M SHALL NOT BE LIABLE FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF PROFITS REVENUE OR BUSINESS RESULTING FROM OR IN ANY WAY RELATED TO PERFORMANCE USE OR INABILITY TO USE ANY OF THE 3M PRODUCT This limitation applies regardless of the legal theory upon which damages are sought For warranty support please call or write your local 3M office or a 3M Authorized Service Provider to obtain an RMA Return Material Authorization number before returning the product If you are inside the Continental United States of America please conta
19. mputing device pursuant to Subpart B of Part 15 of the FCC Rules which are designed to provide reasonable protection against such interference when operated in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help NOTICE This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada INSTRUCTIONS TO USERS This equipment complies with the requirements of FCC equipment provided that the following conditions are met If the cables include EMI ferrite core attach the ferrite core end of the cable to the projector Use the cables which are included with the projector or specified Note Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Statement ElectroMagnectic Com
20. patibility Statement Meets 2004 108 EC Directive Low Voltage Directive Meets 2006 95 EC Directive 2012 3M All Rights Reserved 29 3M Mobile Projector 225 WEEE Statement The following information is only for EU members States The mark shown to the right is in compliance with Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste but use the return and collection systems according to local law RoHS Statement 3M Mobile Interactive Solutions can provide RoHS certification for products meeting the RoHS directive European EU Restriction of Hazardous Substances RoHS Directive 2002 95 EC RoHS compliant means that the product or part does not contain any of the substances in excess of the following maximum concentration values in any homogeneous material unless the substance is in an application that is exempt under RoHS as amended a 0 196 by weight for lead mercury hexavalent chromium polybrominated biphenyls or polybrominated diphenyl ethers or b 0 0196 by weight for cadmium This information represents 3M s knowledge and belief which may be based on information provided by third party suppliers to 3M Patents This product includes a component covered by U S Patent Nos 7 071 908 and 7 667 678 Hong Kong Patent No HK1088976 Australia Patent No 2004241602 United Kin
21. s connected to the projector but the projector will not display the computer s image e Plug the VGA audio cable into the projector and the icon in the upper left corner of the image will display the VGA Audio cable icon See On Screen Icons on page 19 The projector is making a noise e projector has a small fan for cooling the LED light source The fan turns on and off automatically based on the projector s internal temperature The fan will turn on more often in warm environments or at high altitudes e The speakers make noise when the volume is set to high and nothing is connected to the projector audio inputs This is typical Reduce the projector s volume setting to zero e speakers may make noise when the component AV cable is not correctly connected to the video device There are two red connectors on the component AV cable One is for the right audio channel and the other is for the Pr component video signal If these connectors are switched the projected image will appear green and an abnormal noise will come from the right speaker 2012 3M All Rights Reserved 23 3M Mobile Projector MP225 My video device is connected to the projector but the projector will not display the video Unplug the AV cable from the projector and the splash screen will display Plug the AV cable into the projector and the icon in the upper left corner of the image will display the AV cable icon See On Screen
22. s of war disasters such as fire flood and lightning improper electrical current software problems interaction with non 3M products or service other than by an 3M Authorized Service Provider neglect or mishandling by any person Normal wear and tear is not covered under warranty b product is designed to operate in the typical indoor environment This warranty does not cover 3M product used outside of the following circumstances 100V 240V AC 50 60 Hz 35 C 32 95 e 10 80 RH without condensation e 0 1829 0 6000 feet above sea level 2012 3M All Rights Reserved 27 3M Mobile Projector 225 C The air intake and exhaust vent must be clear of obstructions Inadequate air ventilation will cause the 3M product to malfunction or will cause damage to the 3M product which will void the warranty d This warranty does not cover any additional costs including but not limited to those associated with removal cleaning or installation of the 3M product adjustments mechanical or electronic made to the 3M product e This warranty covers only normal use of the product 24 hour per day or other excessive continual use causes strain and is not considered normal use f This warranty does not cover consumables e g batteries g This warranty is not transferable h 3Mis not responsible for warranty service should the label or logo or the rating label or serial number be re
23. scolor 22 2012 3M All Rights Reserved 3M Mobile Projector MP225 Troubleshooting The projector will not turn on e battery is not properly installed or the power adapter is not connected to the projector and a working wall outlet Test the electrical outlet by plugging another electrical device like a radio into the wall outlet to confirm that the wall outlet works e Attempt to remove and replace the battery e Hold down the power button until the projector powers up The status indicator is flashing red when the power button is held down e battery needs to be charged or reinstalled See Charge the Battery on page 12 The image is not visible or is very dim e 3M MP225 Projector is a battery operated device and requires controlled lighting conditions The image may appear very dim in brightly lit rooms e sure the status indicator is green This indicates that the projector is powered on and projecting an image e Projectthe image onto a flat white surface e Decrease the light on the surface where the image is being projected e Decrease the size of the image e When there is nothing connected to the projector it will project the startup screen The projector is displaying a question mark e projector does not support the video or computer input signal Switch to a signal that the projector supports See Supported Computer Signals on page 26 A computer i
24. te with the 3M VGA and AV cables only Connecting to Apple Devices Use the supplied AV cable to input video from an Apple device into the VGA AV input on the projector Compatible Devices The New iPad 3rd Gen iPad 2 iPad 1 iPhone 4S iPhone 4 iPhone 3GS iPhone 3G iPhone iPod Touch 4G 3G 2G iPod Classic iPod Nano 5G 4G 3G Instructions 1 Connect the AV Cable to the projector s VGA AV input 2 Connect the 30 pin connector to your Apple Device to Apple Device m 14 2012 3M All Rights Reserved 3M Mobile Projector MP225 Connecting to a Composite Video Device Optional Accessory Use the AV cable to input video from camcorders digital cameras DVD players and digital media players into the VGA AV input on the projector 1 Connect the AV cable to the projector s VGA AV input 2 Connect the other end of the AV cable to the video device s audio and video outputs Tip Some video devices do not have the standard audio and video connections and may require an AV cable specified by the manufacturer The AV cable allows you to connect your video device to your TV monitor or your projector and may be purchased from the video device manufacturer Once you have the AV cable use the cable adapters to connect the video device cable and the projector cable of soy 2012 3M All Rights Reserved 15 3M Mobile Projector 225 Connecting
Download Pdf Manuals
Related Search