Gamber-Johnson 7160-0318-07
Contents
1. Figure 4 Figure 5 Remove 8 32unc screw Power Cable Pull Strap and Power Cable Cover Figure 7 Figure 6 Replace Power Cable Cover Insert power jack into mating jack to hold the power jack in place on port replicator board and tuck the pull strap into the electrical box Pg 6 DOCKING THE COMPUTER 1 Shut down the computer 2 Make sure the sliding door located on the on the back of the computer has been fully opened exposing the computer s docking connector Figure 8 3 Set computer in the dock a Hook the front of the computer on the front retainer Figure 9 b Lower the back of the computer onto the Alignment Pins Figure 9 Figure 8 c Lightly press down on the back of the computer to ensure it is fully seated Sliding Door Docking Connector 4 Pull the docking handle towards the left side of the dock until the latch catches Figure 10 The Push Button latch can be locked for added security Alignment Pins 5 Boot the computer If the dock 1s powered the computer is powered and ready for use Docking station will operate with computer screen _ opened or closed Front Retainer Figure 9 Docking handle in UNDOCKED position Docking handle in DOCKED position Figure 10 Pg7 REMOVING COMPUTER FROM THE DOCK 1 Shut down computer 2 Auto Lock Insert key and rotate clockwise Button Lock Unlock with key if locked Push button in until lever releas2. This docking station is designed to be used with a variety of Gamber Johnson mounting systems Installation instructions for other Gamber Johnson products are provided with each individual product k T his device is Class B verified to comply with Part 15 of FCC Rules when used with a Panasonic Notebook Computer To assure continued compliance use only shielded interface cables when connecting a peripheral to the docking station Product Mounting Disclaimer Gamber Johnson is not liable under any theory of contract or tort hw for any loss damage personal inury special incidental or consequential damages for personal injury or other damage of any nature arising directly or indirectly asa result of the improper installation or use of its products in vehicle or any other application In order to safely install and use Gamber Johnson products full consideration of vehicle occupants vehicle systems i e the location of fuel lines brakes lines electrical drive train or other systems air bags and other safety equipment is required Gamber Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications and recommendations Gamber Johnson product instruction sheets or workmanship standards as endorsed through the Gamber Johnson Certified Installer Program copyright 2011 Gamber Johnson LLC If you need assistance or have question
3. GAMBER JOHNSON Very Well Connected INSTALLATION INSTRUCTIONS Product Revision Form 7160 0318 00 THROUGH 7160 0318 12 Rev F INST 509 PANASONIC TOUGHBOOK CF 31 MAG DOCKING STATION Printing Spec PS 001 This instruction sheet is for the following products Panasonic Toughbook CF 31 docking station with No integrated high gain antenna pass thru cables Item No 7160 0318 00 P Button lock No RF Item No 7160 0318 04 P Button lock No RF Int power Item No 7160 0318 07 P Auto lock No RF Item No 7160 0318 10 P Auto lock No RF Int power Panasonic Toughbook CF 31 docking station with single integrated high gain antenna pass thru cable Item No 7160 0318 01 P Button lock Single RF Item No 7160 0318 05 P Button lock Single RF Int power Item No 7160 0318 08 P Auto lock Single RF Item No 7160 0318 11 P Auto lock Single RF Int power Panasonic Toughbook CF 31 docking station with dual integrated high gain antenna pass thru cable Item No 7160 0318 02 P Button lock Dual RF Item No 7160 0318 06 P Button lock Dual RF Int power Item No 7160 0318 09 P Auto lock Dual RF Item No 7160 0318 12 P Auto lock Dual RF Int power These instructions are for the docking station only For instructions on features set up and operation of the Toughbook CF 31 computer please refer to the manuals provided by Panasonic with the computer
4. the entire system DO NOT install equipment or route wiring or cords in the deployment path of any air bag When drilling into the vehicle DO make sure that both sides of the surface are clear of anything that could be damaged CAUTION If wiring is shorted to the frame high current conductors can cause hazardous sparks resulting in electrical fires or flying molten metal After Installation Test the docking station to ensure that it is working properly File these instructions in a safe place and refer to them when performing maintenance or re installing WARNING Failure to follow all safety precautions and instructions may result in property damage serious injury or death PRE INSTALLATION RECOMMENDATIONS Conduct a Bench Test Gamber Johnson strongly advises a bench test be conducted to verify that all electronic and software issues are resolved prior to installation 1 Make sure computer is operational by itself 2 Insert computer into docking station and verify that the computer is operating in the dock 3 Interconnect entire assembly and verify start up of all components including other equipment printers modems scanners etc Gamber Johnson recommends positioning of all mounts and equipment in the vehicle prior to the actual install to verify that mounting locations are safe and practical Pg 3 MOUNTING THE DOCKING STATION Mount docking station to mounting system using the four 1 4 20 UNC mounting h
5. es 3 Lift the back of the computer off of the locating pins 4 Lift the computer out from under the Front Retainer DOCKING INDICATOR LED With computer installed in the dock the Docking Indicator LED located on the right side of the dock can be used as a troubleshooting tool Figure 11 GREEN All ports are ready to use ORANGE USB port and LAN port do not function external power is not connected RED PC is not supported or connection is not made RED BLINKING Error has occured in the firmware Stop using at once and contact Panasonic Technical Support NOT LIT PC not installed or PC is OFF Standby or Hibernation Docking Indicator LED Figure 11 ETHERNET PORT INFORMATION Ethernet ports 1 amp 2 will both function when a Panasonic Toughbook CF 31 computer is used with one of the 7160 0318 XX series Docking Stations Gamber Johnson recommends using Ethernet port 2 with a Panasonic Toughbook CF 31 Only Ethernet port 1 will work if a Panasonic Toughbook CF 30 computer is used with one of the 7160 0318 XX series Docking Stations See port locations on Page 2 DRIVERS If needed the software driver for this product can be downloaded from Panasonic s Support Page http www panasonic com business toughbook computer support search downloads asp Pg 8
6. oles on the bottom of the dock Four 1 4 20 UNC x 50 Button Head Mounting Screws are provided in the hardware bag Recommended torque 75 in lbs Over tightening mounting hardware may damage docking Station Use of hardware longer than 5 8 may damage docking station This docking station is designed to be used with a variety of Gamber Johnson mounting systems Installation instructions for other Gamber Johnson products are provided with each individual product S N 4 1 4 20 x 50 Button Head Mounting Screws Clevis Not Included SEVERE VIBRATION INSTALLATIONS Gamber Johnson recommends the use of optional Side Restraints in severe vibration applications Side Restraints and mounting hardware are available seperatly and are assembled to the dock using four provided 8 32 x 38 flat head screws Figure 1 Side Restraints optional Angle as shown and insert into side cutouts on docking staton Secure with prodvided 8 32 flat head screws Figure 1 Pg 4 WIRELESS ANTENNA SWITCH On the CF 30 if using an external antenna Wireless Antenna Switch connected by cable to the WAN port on the dock EXT INT Position the switch toward the EXT side Figure 2 If using the wireless antenna built into the computer or a PC Card type antenna Position the switch toward the INT side Figure 2 This switch does not affect the CF 31 To disable external antenna on the CF 31 install Panasonic part HS10954505 ove
7. r the RF connection on the back of the computer This part can be ordered from Panasonic Attach the supplied tie wrap anchors to the underside of the dock by pushing into the holes in the locations shown Figure 3 Attach cable ties to the anchors as shown Figure 3 Retain the USB and Ethernet cables at the Restraint Bracket using the supplied cable ties Figure 3 If the USB or Ethernet cables do not fit with the Restraint Bracket remove the bracket and restrain the cables with the additional tie wrap anchors supplied in the hardware bag Figure 3 USB Ethernet Support Bracket Assemble cable ties to the anchors and route cables as required Pg 5 POWER SUPPLY INFORMATION NON INTERNAL POWER SUPPLY MODELS Panasonic recommends using a Lind Auto Adapter Lind part number PA1580 2961 to power the docking station It can be ordered from Gamber Johnson part number 14103 or directly from Lind Electronics Minneapolis Minnesota 952 927 6303 Installation of the Power Jack Remove the 8 32 screw and the Power Cable Cover on the bottom of the dock Figure 4 Attach the Power Cable Pull Strap located in the hardware bag to the power jack as shown Figure 5 Plug the power jack into the input jack located on the port replicator circuit board inside the docking station and tuck the pull strap into the docking station as shown Figure 6 Replace the Power Cable Cover to secure the power jack Figure 7
8. s call Gamber Johnson at 1 800 456 6868 CF 31 DOCKING STATION FEATURE IDENTIFICATION Alignment Pin ee Docking Connector External Antenna Interlock Pin Connectors Alignment Pin a USB Port Front Retainer Docking Indicator LED Push Button Auto Lock Docking Handle Wireless Antenna Switch Video Connection ON antenna Serial 2 External Microphone DC In Serial External Speaker Headph WLANIGPS Antenna ai aaa Connector Ethernet Port 2 WWAN Antenna P Ethernet Port 1 Connector ee 7 USB Ports Cable Restraint Bracket Kensington Lock Slot Pg 2 IMPORTANT SAFETY INFORMATION FOR INSTALLERS Safety is dependent on the proper installation and servicing of this docking station It is important to read and follow all instructions before installing this product To properly install a Gamber Johnson docking station you must have a good understanding of automotive electrical procedures and systems along with proficiency in the installation and service of aftermarket vehicle equipment There are no adjustments required at any time of the electrical components within the docking station Opening the port replication housing EXCEPT TO INSTALL THE POWER CABLE will void the product warranty During Installation DO NOT connect this docking station to the vehicle battery until 1 ALL other electrical connections are made 2 Mounting of ALL components is complete 3 VERIFICATION that no shorts exist in
Download Pdf Manuals
Related Search