EverFocus EPTZ100
Contents
1. EPTZ 100 provides 7 different preset tour modes All tours are defined in OSD setup menu 1 PATROL TOUR Preset tour with up to 16 selected presets 2 ALLPRESET TOUR Preset tour with all available presets 3 GROUP 1 TOUR Preset tour with presets 1 4 4 GROUP 2 TOUR Preset tour with presets 1 4 5 GROUP 3 TOUR Preset tour with presets 1 4 6 GROUP 4 TOUR Preset tour with presets 1 4 7 TOUR SCAN Preset tour with defined preset GROUPS TOUR gt tour number 1 7 gt ENTER Camera SAG Fun Tour 01 161 Tour numbers 1 PATROL TOUR 2 ALL PRESET TOUR 3 GROUP 1 TOUR 4 GROUP 2 TOUR 5 GROUP 3 TOUR 6 GROUP 4 TOUR 7 TOUR SCAN Alternative for ALL PRESET TOUR POSITION gt 99 gt ENTER 5 1 5 Pattern tours EPTZ 100 provides 4 programmed pattern tours with up to 10 minutes duration each The pattern tours are started with the TOUR key TOUR gt tour number 17 20 gt ENTER Camera 661 Fun Tour 11 16 Tour numbers 17 Pattern 1 18 Pattern 2 19 Pattern 3 20 Pattern 4 5 1 6 Remote switching of EPTZ 100 output relay The EKB 500 keyboard provides the option to switch the output relay of EPTZ 100 on off Switch relay ON F4 gt 1 gt ENTER Switch Alarm Out _ 1 1 OH Alternative POSITION gt 82 gt ENTER Switch relay OFF CLR F4 gt 1 gt ENTER Switch Alarm Out _ 1 1 OFF Alternative POSITION gt 31 gt ENTER 41 EPTZ100_ma_en_rev03 doc 5 2 EKB 500 OPE2. INPUT 2 INPUT 3 OUTPUT INITIALIZE POWER ON RESET CAMERA DEFAULT FACTORY DEFAULT LENS REFRESH CAMERA REFRESH 25 AUTO RESUME MODE TIME MASK 1 POSITION ENABLE EPTZ100_ma_en_rev03 doc 4 1 3 Main menu After opening OSD setup the MAIN menu is shown at the screen MAIN MENU SYSTEM INFO DISPLAY CAMERA SCAN CONTROL PRIVACY MASK ALARM INITIALIZE EXIT Select a menu item with UP DOWN RIGHT will open submenu NOTE The OSD menu has a timeout function After 2 minutes with no activity the OSD menu will close automatically 4 1 4 System info This menu shows the camera type firmware version and communication settings There are no editable items in this menu SYSTEM INFO TYPE EPTZ100 FIRMWARE 709M809Q BAUD RATE 9600 RS 485 ID 1 PROTOCOL EVERFOCUS 4 1 5 Display The settings in this menu define the overlay displays of the camera CAMERA ID Shows the RS 485 ID on the screen ON display of RS 485 ID OFF no display of RS 485 ID CAMERA NAME With setting ON a camera title with up to 16 characters can be entered ON display of camera title with option for edit OFF no title display PRESET NUMBER ON display number of active preset OFF no preset number display PRESET NAME ON display of a freely editable title up to 16 characters of the preset available for p
3. APPENDIX C TROUBLESHOOTI NG 8 1 GENERAL MALFUNCTION In case of drifted preset position or abnormal reaction of EPTZ 100 speed dome perform a reset of the dome for the reset 3 options are possible Option 1 Setup menu gt INITIALIZE gt POWER ON RESET Option 2 GoTo POSITION 80 Option 3 Power off dome for min 5 seconds then power on 8 2 RECOVERING COMMUNICATION SETTINGS OF CAMERA MODULE If the camera communication settings in the setup menu CAMERA gt ADVANCED SETUP gt SPECIAL gt COMM ADJ were changed accidentally the communication between Speed Dome and camera module may be broken Symptoms a Pan Tilt works but no zoom function b OSD setup works but no access to the submenu CAMERA gt ADVANCED SETUP Correction Step 1 Go in setup menu to INITIALIZE gt CAMERA DEFAULT gt ON and perform a camera reset If this reset works all settings from ADVANCED SETTING menu will be reset to factory defaults Check access to menu ADVANCED SETUP If the submenu opens the communication error is fixed If the problem still exists go to STEP 2 Step 2 Go in setup menu to CAMERA gt RESCUE MODE gt set to ON The values for BAUD RATE and PARITY will appear CAMERA ZOOM SPEED LEVEL 8 ADVANCED SETUP RESCUE MODE ON BAUDRATE 38400 PARITY NONE RETURN Change values for BAUD RATE and try with each changed value access to ADVANCED SETUP menu Check also with PARITY setting ODD EVEN With correct settings access to A
4. Alarm In this menu the alarm reactions for input contacts are defined RELAY OFF ON INPUT1 3 PRESET x OUTPUT OFF ON RETURN 4 1 11 Initialize POWER ON RESET CAMERA DEFAULT FACTORY DEFAULT LENS REFRESH x DAYS OFF 1 15 CAMERA REFRESH x DAYS OFF 1 15 It is possible to switch the output relay remotely with this menu item for test purpose ON output relay switched OFF output relay not active off Assignment of the preset position which is linked to alarm input Select preset position 1 32 ON the camera will go to preset assigned preset position in lines above in case of alarm In case of alarm the camera moves to the defined preset and stays there until manual PTZ control or any programmed AUTO RESUME function is carried out OFF no reaction in case of active alarm input Return to main menu ON performs a PTZ initialization similar to power on OFF returns to INITIALIZE menu ON reset ofthe camera module to factory settings OFF returns to INITIALIZE menu ON reset of the pan tilt electronics module to factory settings OFF returns to INITIALIZE menu Frequent initialization of zoom lens for better stability and preset precision OFF no frequent initialization 1 15 interval in days for initialization Frequent initialization of pan tilt mechanism for better stability and preset precision OFF no frequent initialization 1 15 interval in days for initialization 37 EPTZ100_
5. However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This Product is RoHS compliant RoHS WEEE Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at your local community waste collection recycling centre In the European Union there are separate collection systems for used electrical and electronic product Please help us to conserve the environment we live in Ihr EverFocus Produkt wurde entwickelt und hergestellt mit qualitativ hochwertigen Materialien und Komponenten die recycelt und wieder verwendet werden k nnen Dieses Symbol bedeutet dass elektrische und elektronische Ger te am Ende ihrer Nutzungsdauer v
6. IMAGE ADJ FREEZE Store freeze current video image H REV Flips the image horizontally V REV Flips the image vertically SHARPNESS Image sharpness adjustment in the range 1 30 COLOUR GAIN Colour saturation adjustment in the range 1 50 END Return to CAMERA ADVANCED SETTING page RESET Reset of the camera parameters to factory defaults EXIT Return to CAMERA menu 30 EPTZ100_ma_en_rev03 doc 4 1 7 Scan This menu contains all setup options for automatic dome modes such as autopan preset tours and pattern SCAN AUTO PAN ALL PRESET GROUP SCAN TOUR SCAN PATROL PATTERN AUTO PAN PAN TILT This autopan mode performs pan and tilt movements between 2 points The vertical movement will be processed in programmed speed from start end point the resulting movement is shown if the schema below START Left autopan limit Move to the position and press IRIS to store the start point END Right autopan limit Move to the position and press IRIS to store the end point SPEED Autopan speed range from 2 slowest to 180 fastest DWELL Dwell time at start and end position adjustable 1 45 seconds RUN Autopan start this function will close OSD menu RETURN Return to AUTO PAN menu PAN ONLY This autopan mode performs a horizontal movement between 2 points START Left autopan limit Move to the position and press IRIS to store the start point END Right autopan limit Move to the posit
7. IRIS SHUTTER AGC SSNR SENS UP SPECIAL SETUP USER PRESET PRIVACY DAY NIGHT SYNC COMM ADJ IMAGE ADJ OSD Structure Part 1 MAIN MENU rat SYSTEM INFO MAIN SETUP SYSTEM INFO TYPE CAM TITLE DISPLAY FIRMWARE WHITE BAL CAMERA BAUDRATE BACKLIGHT SCAN RS 485 ID MOTION DET CONTROL PROTOCOL FOCUS PRIVACY MASK EXPOSURE ALARM DISPLAY SPECIAL INITIALIZE CAMERA ID RESET EXIT CAMERA NAME PRESET NUMBER PRESET NAME PTZ POSITION CAMERA ZOOM SPEED ADVANCED SETUP RESCUE MODE AUTO PAN BAUDRATE KANANA E PAN ONLY CIRCLE SCAN ALL PRESET AUTO PAN SPEED ALL PRESET DWELL GROUP SCAN RUN TOUR SCAN ROL GROUP SCAN PATTERN hour GROUP2 GROUP3 GROUP4 TOUR SCAN GROUP1 GROUP2 GROUP3 GROUP4 SPEED DWELL RUN PATROL PRESET SPEED DWELL RUN PATTERN 1 RECORD PREVIEW RUN DELETE 24 IMAGE SETUP FREEZE H REV V REV SHARPNESS COLOUR GAIN EPTZ100_ma_en_rev03 doc OSD Structure Part 2 MAIN MENU SYSTEM INFO DISPLAY CAMERA SCAN CONTROL PRIVACY MASK CONTROL ALARM AUTO RESUME INITIALIZE POWER ON RESUME EXIT IMAGE FLIP PRIVACY MASK MASK 1 MASK 2 MASK 3 MASK 4 ALARM RELAY INPUT 1
8. PTZ Initialization POSITION gt 80 gt ENTER 39 EPTZ100_ma_en_rev03 doc 5 1 1 EPTZ 100 setup menu Start EPTZ menu If DVR Main monitor is selected DVR in LCD display CAM hold MENU If no DVR main monitor is selected MENU or GAM hold MENU or alternatively in both modes SHIFT hold PRESET gt 9 5 gt ENTER Switch between the settings JOYSTICK v 4 Enter submenus JOYSTICK gt in CAMERA gt ADVANCED SETUP IRIS Change the settings JOYSTICK EXIT OSD menu submenus Menu item EXIT RETURN gt JOYSTICK gt in CAMERA gt ADVANCED SETUP IRIS Note Exceptional commands are described in the OSD 5 1 2 Preset positions Up to 64 preset PTZ positions can be stored in EPTZ 100 Save presets SHIFT hold POSITION Camera Save to gt preset number gt ENTER Fositior ___1 132 Delete preset Camera Bd CLR hold POSITION Del Position gt preset number gt ENTER Start go to preset Camera Bl go to POSITION gt preset number gt ENTER Positiorr 1 192 5 1 3 Autopan The speed for autopan function is programmed in OSD menu the entered value for speed in EKB 500 will be ignored at start of autopan Activate A B autopan pan between 2 points A PAN gt any value 1 239 gt ENTER Speed 11 233 ENT to start Activate 360 autopan SHIFT hold A PAN gt any value 1 239 gt ENTER 40 EPTZ100_ma_en_rev03 doc 5 1 4 Preset tours
9. describes the basic settings in the EKB 500 keyboard to establish communication with speed dome cameras 6 1 COM PORT SETTING RS 485 INTERFACE SETTING Telemetry protocol type and transmission rate are defined in this menu rie a 21 MENU gt COM PORT SETTING gt ENTER Port lore Select port 1 or 2 and confirm with ENTER Use the JOYSTICK 4 y to change the value BAUD J664 lt Selection 1200 2400 4800 9600 Baud 4 4 Ito change Press ENTER to confirm the setting and ESG to cancel The next menu is used for telemetry protocol Protocol EUF 2 setting J ta change Use the JOYSTICK y 4 to change the value Selection EVF 2 recommended protocol for optimized EKB 500 functionality Pelco D Pelco P Input the port NOTE Baud rate and protocol type have to comply with the EPTZ 100 settings for these parameters DS1 DIP switch setting Press ENTER to confirm the selection and ESG to cancel Fort 1 Changed ENT lto save 6 2 DEVICE SETTING gt CAMERA Define in this menu RS 485 ID address and connected RS 485 port MENU gt DEVICE SETTING gt CAMERA SETTING gt ENTER Camera Hame Camera number 1 9999 independent from RS 485 address Press Enter to confirm the setting and Esc to cancel Setup of the RS 485 interface which is connected to EPTZ 100 RAS485 Connected to port 1 or 2 Fort ioff 1 2 Press Enter to confirm the setting and ESC to cancel RS465 Address Enter the RS
10. 41 5 1 5 Paternidad hacen Nea Aa By 41 5 1 6 Remote switching of EPTZ 100 output relay ccc ee ee een nnnne nn nnnnn nen nnnen aaa nnrnnenn 41 5 2 EKB 500 Operation with Pelco D P Protocol mnrnennnenennnnnnne nennen nnrnn nennen nn 42 5 2 1 EPTZ7100 SetuB Menu ur ee A 42 5 2 2 Preset positi nszn 2 RE SATENE EEE EA SAE EAEE EEE Eas 42 AS AN 43 A e E TOUS ernie A NN 43 5 2 5 Paternidad it dt 43 3 EPTZ100_ma_en_rev03 doc 5 2 6 Remote switching of EPTZ 100 output relay coooocccccnncccnnnnnnnnonnnnnoneninnnnnoncnnnnnrnnnnnncrnnnnns 44 6 APPENDIX A Basic Settings at EKB 500 keyboard ooooocociccccinnccnconoccccnnnnnnnnninancnnnnnnnnnnninnancnnnns 45 6 1 COM PORT SETTING RS 485 interface SettidQ ooooocccocnnnccninnnorcnnnnnoronononoronnn non nnren nn 45 6 2 DEVICE SETTINGS CAMERA ic ein a a a aaaea 45 7 APPENDIX B Basic Settings at EverFocus DVR esnsssenennnnnenennnnnnnennnnnn nen nnnnn nennen eeeee nea 46 7 1 EDR EDVR EDSR series except EDSR100 EDSR100H eene 46 7 2 ECOR PARAGON SOMOS rasant ee 46 8 Appendix C Troubleshooting ommicicionici a ed 47 8 1 General Ma ltUnCtho Mm rise sais saci aAA ae A re ine ETE Tran 47 8 2 Recovering Communication Settings of Camera Module usnrsreennnnnennnnnen een 47 4 EPTZ100_ma_en_rev03 doc 2 INTRODUCTION The mini PTZ speed dome EPTZ 100 provides ideal discreet surveillance for CCTV indoor applications Engineered with the lat
11. 485 address of the EPTZ 100 Hel Video Connected ta o ne If the camera is connected to an EverFocus DVR enter the DVR number and video input number Enter any value if no DVR is connected numeric entry compulsory Camera H001 changed EMT to saue Press ENTER to confirm the setting and ESC to cancel 45 EPTZ100_ma_en_rev03 doc 7 APPENDIX B BASIC SETTINGS AT EVERFOCUS DVR The following settings are required to establish RS 485 communication between DVR and speed dome 7 1 EDR EDVR EDSR SERIES EXCEPT EDSR100 EDSR100H 1 CAMERA menu enter the correct RS 485 ID address at the speed dome camera channel 2 CONTROL menu under RS485 BAUD RATE set value identical to camera baud rate PARITY NONE DATA BIT 8 STOP BIT 1 PROTOCOL set protocol identical to speed dome protocol NOTE The RS 485 ID in CONTROL menu is not related to speed dome control This RS 485 ID is used for controlling DVR by external keyboard only 7 2 ECOR PARAGON SERIES 1 CAMERA menu enter the correct RS 485 ID address at the speed dome camera channel 2 SYSTEM gt I O CONTROL menu BAUD RATE set value identical to camera baud rate PARITY NONE DATA BIT 8 STOP BIT 1 PROTOCOL set protocol identical to speed dome protocol NOTE The RS 485 ID in menu I O CONTROL menu is not related to speed dome control This RS 485 ID is used for controlling DVR by external keyboard only 46 EPTZ100_ma_en_rev03 doc 8
12. DVANCED SETUP is possible the submenu appears additional to the camera menu on the screen MAIN SETUP CAMERA gt ZOOM ISPEED REVEL ABVANCEDAISETUP ATWe RESCUE MODE ONF BAUDRAT BET 38400 PAR DIED NONE REPURNRE SPECIAL RESET EXIT Switch off the CAMERA menu display by pressing IRIS key Go to gt SPECIAL gt COMM ADJ and set verify following default settings BAUD RATE 38400 UART MODE 8 N 1 RET PKT ENABLE EXIT all menus Restart the EPTZ 100 with power OFF ON to finish the camera setting recovery 47 EPTZ100_ma_en_rev03 doc EverFocus Electronics Corp Head Office 12F No 79 Sec 1 Shin Tai Wu Road Hsi Chih Taipei Taiwan www everfocus com tw USA Subsidiary 1801 Highland Ave Unit A Duarte CA 91010 U S A www everfocus com European Subsidiary Albert Einstein Stra e 1 D 46446 Emmerich am Rhein Germany www everfocus de 48 China Subsidiary Room 609 Technology Trade Building Shandgdi Information Industry Base Haidian District Beijing China www everfocus com cn Japan Subsidiary 1809 WBG MARIBU East 18F 2 6 Nakase Mihama ku Chiba city 261 7118 Japan www everfocus com f EverFocus EPTZ100_ma_en_rev03 doc
13. EPTZ 100 Day Night Speed Dome Camera INSTALLATION OPERATION f EverFocus 1 SAFETY WARNINGS Do nat place the device near to heaters furnaces other heat sources or under direct solar irradiation Operate the device only in locations providing the tolerable operating temperature range 0 C 40 C For cleaning make sure the device is plugged off and only use a damp cloth without acid detergent Install the device only in dry and dustproof surroundings Protect the device against any liquid s penetration e Avoid the penetration of any artefacts e g through ventilation slots Do nat open the device yourself In case of malfunction contact your local installer or dealer Unauthorized opening of the device will annul the warranty claim Use the device only for purposes described in this manual Operate the device only with the power source indicated in this user manual ATTENTION This is a class A product which may cause radio interference in a domestic environment in this case the user may be urged to take adequate measures This equipment has been tested and found to comply to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications
14. EXIT gt ENTER Pan tilt JOYSTICK V4 gt Zoom TELE WIDE TELE ZOOM IN or JOYSTICK rotation to the right WIDE ZOOM OUT or JOYSTICK rotation to the left Focus TELE FOCUS F WIDE FOCUS N Iris open close Open iris IRIS close iris IRIS Go to position preset Preset number POSITION POSITION preset number gt ENTER Save position preset SHIFT hold POSITION gt preset number gt ENTER Delete preset CLR hold POSITION gt preset number gt ENTER Start patrol tour TOUR gt 1 gt ENTER Start all preset tour TOUR gt 2 gt ENTER TOUR gt 3 gt ENTER Start preset tour Group 1 Start preset tour Group 2 TOUR gt 4 gt ENTER Start preset tour Group 3 TOUR gt 5 gt ENTER Start preset tour Group 4 TOUR gt 6 gt ENTER Start preset Tour Scan TOUR gt 7 gt ENTER Start pattern 1 TOUR gt 17 gt ENTER Start pattern 2 TOUR gt 18 gt ENTER Start pattern 3 TOUR gt 19 gt ENTER Start pattern 4 TOUR gt 20 gt ENTER Start autopan A PAN gt speed enter any value the speed is defined in OSD menu gt ENTER 360 autopan SHIFT hold A PAN gt speed enter any value the speed is defined in OSD menu gt ENTER Start home position HOME Switch ON output relay F4 gt 1 gt ENTER Switch OFF output relay GLR F4 gt 1 gt ENTER
15. PTZ100_ma_en_rev03 doc 2 4 SPECIFICATIONS Camera Sensor Effective pixels Horizontal resolution Sensitivity Video output S N ratio Sync system Electronic shutter Digital Slow Shutter DSS White balance Back light compensation Gain Flicker cancel DNR Dynamic Noise Reduction Day night switching Lens Zoom ratio Focus length Aperture Viewing angle Minimum object distance Focusing method Communication Communication Built in protocols Baud rate Speed dome address range Alarm Alarm PTZ functionality Horizontal rotation range Tilt rotation range Auto pan 2 points scanning Auto pan speed Auto pan dwell time A B points Preset positions Preset tours Dwell time at preset position Pattern Running to position speed Manual pan tilt speed Position accuracy 1 4 CCD SONY Super HAD 380 000 NTSC 440 000 PAL 520 TV lines colour mode 570 TV lines b w mode 0 7 lux F 1 8 50 IRE colour mode 0 02 lux F 1 8 50 IRE b w mode 0 005 lux DSS x 128 Composite 1 Vp p sync negative over 50 dB internal 1 60 1 120 000 NTSC 1 50 1 120 000 PAL automatic ESC or manual up to 128 x auto AWC ATW mode manual adjustable 3 steps OFF adjustable 3 steps OFF ON OFF adjustable 3 steps OFF IRC b w switching manual automatic 10x optical autofocus zoom 10x digital zoom max 100x f 3 8 wide 38 tel
16. RATION WITH PELCO D P PROTOCOL NOTE Not all EPTZ 100 functions are available in PELCO D P protocol Operation for ssome functions is different to operation with EVERFOCUS protocol 5 2 1 EPTZ 100 setup menu Start EPTZ 100 menu If DVR Main monitor is selected DVR in LCD display CAM hold MENU If no DVR main monitor is selected MENU or GAM hold MENU or alternatively in both modes SHIFT hold PRESET gt 9 5 gt ENTER Switch between the settings JOYSTICK y 4 Enter submenus JOYSTICK gt in CAMERA ADVANCED SETUP IRIS Change the settings JOYSTICK EXIT OSD menu submenus Menu item EXIT RETURN gt JOYSTICK gt in CAMERA ADVANCED SETUP IRIS Note Exceptional commands are described in the OSD 5 2 2 Preset positions Up to 64 preset PTZ positions can be stored in EPTZ 100 Save presets SHIFT hold POSITION Camera Gaal Save to gt preset number gt ENTER Position 1 152 Delete preset Caner 68a CLR hold POSITION Del Position gt preset number gt ENTER Start go to preset Camera H661 go to Position _ 41 132 POSITION gt preset number gt ENTER 42 EPTZ100_ma_en_rev03 doc 5 2 3 Autopan The speed for autopan function is programmed in the OSD menu the entered value for speed in EKB 500 will be ignored at start of autopan Activate A B autopan pan tilt between 2 points A PAN Pelco P only Alternative POSITION gt 99 gt ENTER 5 2 4 P
17. RS 485 installation with EverFocus DVR It is possible to control the EPTZ 100 speed dome by EverFocus DVR except 1 Ch models via network A combined local control by EKB 500 keyboard and remote network control by DVR is also possible For a combined local and remote PTZ control it is mandatory that DVR and speed dome are connected to the same RS 485 port of the EKB 500 keyboard The RS 485 signal is looped through the DVR Combined local and remote PTZ control with star wring to dome and RS 485 distributor The drawing below shows an incorrect RS 485 connection for controlling the DVR locally and remotely With this way of installation only local PTZ control is possible EE y PORT 1 PORT 2 Incorrect wring for combined local and remote PTZ control 18 EPTZ100_ma_en_rev03 doc 3 2 4 Alarm EPTZ 100 provides 3 alarm input contacts and 1alarm output relay lt is also possible to trigger the alarm output relay by EKB 500 keyboard command For input contacts use dry Normal Open N O contacts only The maximum load of output relay contacts is 30 V AC DC 0 5 A max external dry N O contact external dry N O contact Alarm In 3 yellow external dry N O contact Relay Out N C purple Relay Com blue Relay Out N O grey 1 9 EPTZ100_ma_en_rev03 doc 3 3 COMMUNICATION SETTINGS The setup for general RS 485 parameters protocol type RS 485 address and baud rate is done by DIP switches locat
18. Z 100 CPM uunnnsreeennnnnenennnnnnnennnnnn een nnnennen 10 INSTALLATION 2 2 En ern EEE Adern ee 11 Sal Mech nlcal ersehen enter adheres 11 3 1 1 Celing MOI tl dro oda Dti 11 3 1 2 Recessed ceiling MOUNT re BD 12 A O AO 13 3 1 4 Ceiling pendant MOUNT re rr se nnnnnnen nn 14 8 2 Elo a a O nent cama ee fee 15 3 2 1 Md A ds 15 3 2 2 PO Wii ia a 15 3 2 3 ANO 16 324 O TA 19 3 37 COMMUNICATION Setting Sissi enean A aaa 20 3 3 1 Baud rate and Protocols scene en 20 3 322 RS 485 1Bi address usina ia lenta 21 3 3 3 RS 485 bus termination uusnssseennnsenenn nennen nennen nnnnn nennen nnnnnn en nnnrenennnnrne nennen 23 A E ehe na ae nen se Dee data N en FREUT a naan 23 OSD MENU SU aaa 23 4 1 1 Operation in Setup MENU iene triere ira yaaa 23 A ON 24 4 1 3 MANTIS A A AA Ad A 26 ANA System Mi a Maat ET 26 4 1 5 Display er es 26 AN Gir A an een de ann de near NT 27 A HEBEN OTEENTEERSTLEOTSOFEEHOEREIERESIEON 3l 4 1 8 COMO nn ran Han elle nenne area catand RER ER 35 4 1 9 Privacy Mask ii a A ih 36 AMOS Alarm rd ad ia disc 37 4 1 11 Initiallze NO 37 OPERATION WITH EKB 500 KEYBOARD 0cceccecee eer tinkt terete reer eee nennen nennen nn 38 5 1 EKB 500 operation with EverFocus protocol EVE 2 000occcconocccccnnnococonnnnnnnnnnnncnnnnnnncrnrnnonnnns 39 5 1 1 EPTZ 100 setup MENU rss ro io pepsi 40 5 1 2 Proset postions iii talca 40 O a a re 40 5 1 4 Preset toU SE een BET cas di brads En ee NO
19. a movement EPTZ 100 can store 4 patterns with a maximum length of 10 minutes each 1 4 Select a pattern for programming checking RECORD Start the movement programming with Go To Preset 1 All manual movements zoomings are recorded now The TIMER in the display counts down the available time remaining in seconds PREVIEW Shows the programmed pattern Any pan tilt command returns to PATTERN menu RUN Starts the selected pattern this function will close OSD menu DELETE Deletes the selected pattern RETURN Return to SCAN menu RETURN Return to MAIN menu 34 EPTZ100_ma_en_rev03 doc 4 1 8 Control This menu provides settings for resume function after inactivity power up and special functions AUTO RESUME OFF ON gt AUTO RESUME is the reaction of the dome after a defined time of inactivity no operator action ON auto resume activated OFF auto resume not active MODE Type of resume reaction AP P T A B autopan pan tilt AP C 360 autopan circle AP P A B autopan pan only ALL PRESET preset tour with all presets GROUP1 4 GROUP preset tour 1 4 TOUR preset tour with selected GROUPS PATROL preset tour with selected preset positions PRESET x go to preset position x NOTE The HOME key of EKB 500 keyboard performs a Go to Preset 1 command If similar functionality is desired for AUTO RESUME select PRESET 1 in this menu TIME Duration of inactivity before performing the AUTO RESUME reaction ad
20. alance mode ATW Auto tracking white balance ATW continuously checks the whole image weights all colours in the picture and updates the white level and colour temperature which is suitable for constantly changing scene 2 options are available for ATW indoor and outdoor Indoor mode tends to be more blue and outdoor mode adds more red to the whole image AWC Auto white balance Camera will make colour calibration of the picture for once and keep the colour temperature until the next command is given To refresh the colour a manual trigger needs to be done to the AWC when shown on the display Manual Manual adjustment of colour preference With manual setting the colour temperature can be fixed which can be suitable for indoor and static environment If the lighting is Tungsten or similar more natural try to either add 27 EPTZ100_ma_en_rev03 doc BACKLIGHT MOTION DET FOCUS some blue or reduce some red if lighting is fluorescent or within white spectrum try to either add some red or reduce some blue Default values are 30 for RED and 40 for BLUE it is recommended not to set the values too far away from these two default values Back light compensation improves the image quality in scenes with extreme light behind the object which usually washes out the image considerably Back light function is used to reduce if necessary both exposure time and video gain to avoid over exposure Use the back light compensation for
21. dapter Make sure that position of the camera module connector fits the correct position of the connector board 6 After plug in turn the camera module some degrees clockwise to latch the camera module Connector 7 Assemble the cable cover 8 Use the hex key to fix the camera position with the locking screw 13 EPTZ100_ma_en_rev03 doc 3 1 4 Ceiling pendant mount Ceiling pendant mount requires the optional adaptor EPTZ 100 CLM 1 Assemble the connector board to the bracket adapter by 3 M4 screws Follow the red arrow marks at board and ceiling adapter for correct position 2 Mount the bracket adapter with the connector board to the EPTZ 100 CLM For wiring use the upper hole or side outlet of the tube 3 Mount the EPTZ 100 CLM to the ceiling 4 Plug the dome module in the ceiling adapter Make sure that position of the camera module connector fits the correct position of the connector board 5 After plug in turn the camera module some degrees clockwise to latch the camera module gt lol OH O 7 j g lf j EN Om T DA So E LA ORs HI en e TN 6 Use the hex key to fix the camera position with the locking screw 14 EPTZ100_ma_en_rev03 doc 3 2 ELECTRICAL 3 2 1 Video EPTZ 100 provides a composite 1 Vp p video output PAL NTSC video system depending on ordered version with a BNC cable socket Cameras and video displaying or processing equipment DVRs s
22. e mm F 1 6 wide F 2 8 tele 51 2 wide end to 5 58 tele end 15m auto one push AF manual RS 485 simplex 2 wire EverFocus Pelco P Pelco D setup by DIP switch 2400 4800 9600 bps setup by DIP switch 1 255 setup by DIP switch 3 inputs 1 output with tour position auto triggering 360 unlimited rotation 90 with auto flip function adjustable speeds adjustable end stops 2 6 12 30 60 120 second 1 3 5 10 30 45 s 64 1 tour with first 16 positions 4 group tours with 4 positions each 1 tour with individual setup up to 32 positions 1 255s 4 x pattern with up to 800 movements 600 s PTZ recording each up to 240 sec 0 5 240 sec 0 225 6 EPTZ100_ma_en_rev03 doc Alarm Proportional pan speed Privacy zones Setup Auto resume Video output Power Power source Power consumption Physical environment Connectors Ambient temperature Humidity Protection rating Dimensions Weight Delivery scope 3 inputs 1 output with tour position auto triggering yes 4 zones free adjustable multiline OSD setup menu after 1 2 3 4 5 or 10 min no activity go to BNC cable socket 24 V AC 10 19 W max with PTZ motors 12 W max without PTZ motors Video output BNC cable socket Power RS485 Alarm connector cable open cable end cable length 90 cm 0 C 40 85 max IP20 for indoor applications only 200 height with ceiling m
23. ed at the top of the camera module Correct settings are essential for communication with the dome controller For correct communication all 3 parameters protocol baud rate and RS 485 ID have to comply with the PTZ controller settings The 120 Ohm termination DS3 is used at the last dome in the RS 485 bus for avoiding reflections in the RS 485 bus Location of DIP switches DS3 DS1 DS2 DS1 Protocol and baud rate DS2 RS 485 ID address DS3 120 Ohm termination of RS 485 bus 3 3 1 Baud rate and Protocol The baud rate setting is done by switch 1 and 2 of DS1 Baud Rate 12 2400 APA The telemetry protocol setting is done by switch 3 4 and 5 of DS1 Protocol 345 Pelco D 5 la Pelco P z A EverFocus 8 B 20 EPTZ100_ma_en_rev03 doc The RS 485 ID address setting is done by DIP switch DS2 The following table shows the switch positions for the possible addresses 1 255 3 3 2 RS 485 ID address Address Switch Address Switch Address Switch Address Switch Kungamag 118 ON FAA 22 Kunuemaul 54 Runumung 86 119 EELEITIES TOS SSG BeBe 87 ii EPTZ100_ma_en_rev03 doc 21 Address Switch Address Switch Address Switch Address Switch EPTZ100_ma_en_rev03 doc Funnyenn 234 RES 22 omg na 202 TREAES 165 174 175 177 186 3 3 3 RS 485 bus termination The last device in an RS 485 bus should be terminated by 1200hm resistor to avoid
24. est Digital Slow Shutter DSS x128 technology EPTZ 100 can improve CCD sensitivity producing quality images also under low light conditions EPTZ 100 offers enhanced features such as privacy zones noise reduction and 4 pattern tours with total 40 minutes duration 2 1 FEATURES e Compact size design for discreet surveillance only 114 mm 4 5 diameter e 100x total zoom 10x optical 3 8 38 mm and 10x digital autofocus zoom e High resolution 520 TVL colour mode 570 TVL b w mode e Image capture in almost complete darkness with DSS 128x max e True day night operation with automatic IR cut filter e High speed pan tilt up to 240 sec e 360 endless pan e Digital Noise Reduction e 4 zone privacy masking e RS 485 communication with EverFocus Pelco D and Pelco P protocol e 4x 10 minutes pattern tour programmable camera movement e 3alarm inputs 1 alarm output relay e Includes adapter for ceiling surface mount and recessed ceiling mount 2 2 DELIVERY SCOPE 1 x Speed dome camera module 1 x Connector board 1 x Ceiling mount adapter 1 x Metal ring for recessed ceiling mount 1 x Plastic cover ring for recessed ceiling mount 1 x Drilling template for ceiling mount 1 x Accessory screw set 1 x User manual 2 3 OPTIONAL ACCESSORIES EPTZ 100 WLM Wall mount bracket EPTZ 100 CLM Ceiling pendant mount adapter EKB 500 Universal RS 485 controller keyboard 24 VAC power supply type depends on sales region 5 E
25. g at focusing focusing focusing no action nn sinn ZOOM SPEED Zoom speed setting FAST or SLOW D ZOOM Value for maximum digital zoom ratio LIMIT x2 x10 DISP ZOOM MAG ON Overlay display of zoom position on the screen 28 EPTZ100_ma_en_rev03 doc EXPOSURE ZOOM POS INIT LENS INIT END BRIGHTNESS IRIS SHUTTER AGC SSNR SENS UP END Defines a zoom position after powering up the camera range is x1 x10 Reset of the autofocus lens in case of malfunction Return to CAMERA ADVANCED SETTING page Image brightness setting range 1 100 Mode of the lens iris AUTO automatic iris mode MANUAL manual iris operation Electronic exposure control ESC Electronic auto shutter the shutter speed is automatically adapted to light conditions NOTE This mode item is only available for setup if IRIS mode is set to MANUAL MANUAL Manual setup of shutter speed A FLK Flickerless mode Useful in sceneries with light sources powered with a frequency different from the camera Automatic Gain Control gains video signal under low light conditions HIGH AGC ON high gain NORMAL AGC ON normal gain OFF AGC off SSNR and SENS UP are not available in this mode Signal noise reduction This feature improves the signal noise ratio under low light conditions OFF no noise reduction LOW MID HIGH level of noise reduction NOTE this feature requires setting AGC NORMAL or HIGH The SENS UP function increases the l
26. ight sensitivity by interpolation of several images AUTO SENS UP function active Enter the submenu to enter the number of maximum interpolated pictures 2 128 NOTE Please consider that a higher value creates brighter pictures but due to the longer calculation time moving objects may appear distorted in the picture effect similar to longer exposure time at photo cameras OFF no SENS UP function NOTE this feature requires setting AGC NORMAL or HIGH Return to CAMERA ADVANCED SETTING page 29 EPTZ100_ma_en_rev03 doc SPECIAL Submenu for advanced camera functions USER PRESET Not supported by EPTZ 100 PRIVACY Keep OFF setting privacy mask setup is done in the PRIVACY MASK menu available in the main menu DAY NIGHT Modes of the day night switching B W black white night mode IR cut filter switched off COLOUR colour day mode IR cut filter switched on AUTO1 day night switching with short delay time AUTO2 day night switching with longer delay time SYNC Synchronization mode fixed at INTERNAL mode COMM ADJ Communication settings for camera interface ATTENTION Do not change any value in this submenu Keep default settings CAM ID 0 DISPCAMID OFF BAUD RATE 38400 UART MODE 8 N 1 RET PKT ENABLE If these settings are changed for whatever reason the communication between dome electronics and camera menu will be broken In this case consult APPENDIX C for recovering camera module communication settings
27. ion and press IRIS to store the end point SPEED Autopan speed range from 2 slowest to 180 fastest DWELL Dwell time at start and end position adjustable 1 45 seconds RUN Autopan start this function will close OSD menu 3 1 EPTZ100_ma_en_rev03 doc RETURN Return to AUTO PAN menu CIRCLE This autopan mode performs a continuous horizontal 360 movement TILT Adjust the vertical position of the camera press LEVEL IRIS to store the vertical angle SPEED Autopan speed range from 2 slowest to 180 fastest RUN Autopan start this function will close OSD menu RETURN Return to AUTO PAN menu RETURN Return to SCAN menu ALL PRESET This type of preset tour includes all programmed preset positions SPEED Pant tilt speed for movement between preset positions range from 2 slowest to 180 fastest DWELL Dwell time at preset positions adjustable 1 45 seconds global setting for all presets RUN Start preset tour this function will close OSD menu RETURN Return to SCAN menu GROUP SCAN Pre defined preset tours with 4 preset positions each Group 1 preset positions 1 4 Group 2 preset positions 5 8 Group 3 preset positions 9 12 Group 4 preset positions 13 16 GROUP1 SPEED Pant tilt speed for movement between preset positions range from 2 slowest to 180 fastest DWELL Dwell time at preset positions adjustable 1 45 seconds global setting for all presets RUN Start GROUP tour this function will clo
28. justable from 1 to 10 minutes POWER ON OFF ON Resume action after power up of the dome RESUME ON after dome initialization at power up the dome will start in the mode which is defined under AUTO RESUME OFF no resume function at power up IMAGE FLIP OFF ON ON image is displayed horizontally flipped mirror OFF normal image display RETURN Return to MAIN menu 35 EPTZ100_ma_en_rev03 doc 4 1 9 Privacy Mask EPTZ 100 allows for masking 4 different areas to protect private or confidential zones in the field of view MASK1 4 OFF ON shows the status of the privacy zone ON privacy zone masking active OFF privacy zone off RIGHT enters the submenu to mask setup POSITION Definition of size and position of the privacy zone Step 1 the corner in the screen marks the upper left border of the privacy zone IRIS OPEN NEXT STEP Move the camera to the desired position and press IRIS OPEN to proceed Step 2 next screen shows the lower right border of the privacy zone IRIS CLOSE TO EXIT Move the camera to the desired position and press IRIS CLOSE to proceed The defined mask will appear on the screen ENABLE ON privacy zone masking active OFF privacy zone off RETURN Returns to privacy mask menu RETURN Returns to MAIN menu NOTE If privacy masking is active the pan tilt speed of the dome is reduced for ensuring correct processing of privacy masks 36 EPTZ100_ma_en_rev03 doc 4 1 10
29. ma_en_rev03 doc 5 OPERATION WITH EKB 500 KEYBOARD The following chapter describes the EPTZ 100 operation with EKB 500 keyboard with firmware 1 5 or higher EPTZ 100 is optimized for protocol type EVF 2 of EKB 500 keyboard Basic communication settings for EKB 500 are described in APPENDIX A For further details please refer to the EKB 500 user manual The following operating elements are available for EPTZ 100 PTZ control LEFT El Esa Camera funetions Automatic functions 3 axis joystick DOWMWARD General key description IRIS manual iris control opens iris closes iris FOCUS F N manual focus F TELE N WIDE ZOOM IN QUT zoom keys same function as joystick rotation IN TELE OUT WIDE POSITION start and save positions TOUR start preset tours and pattern tours APAN autopan start and save automatic pan operation HOME go to home position preset position 1 FA remote switching of EPTZ 100 output relay MENU opens EPTZ 100 OSD setup menu SHIFT switch key for second key level depending on function 38 EPTZ100_ma_en_rev03 doc 5 1 EKB500 OPERATION WITH EVERFOCUS PROTOCOL EVF 2 Operation outline Function Keys operation Open dome menu MENU or CAM hold MENU if main monitor of DVR is selected or SHIFT hold POSITION gt 95 Switch menu functions JOYSTICKY A Change menu settings JOYSTICK Leave dome menu GLR hold MENU or menu item
30. om Hausm ll getrennt entsorgt werden sollen Bitte entsorgen Sie dieses Ger t bei Ihrer rtlichen kommunalen Sammelstelle oder im Recycling Centre Helfen Sie uns bitte die Umwelt zu erhalten in der wir leben The information in this manual was current upon publication The manufacturer reserves the right to revise and improve his products Therefore all specifications are subject to change without prior notice Misprints reserved Please read this manual carefully before installing and using this unit Be sure to keep it handy for later reference 2 EPTZ100_ma_en_rev03 doc TABLE OF CONTENTS 4 2 3 4 SAFETY WARNINGS 2 22 aa AO bid 2 INTRODUCTION cr tuinarennioineante an a ieee aa a aa eh an ean aiaa na a E a eaa 5 2 1 Fed O OE 5 2 2 Delivery Scopi aaa aae a a ae Ea a teres 5 2 39 Optional accessorie iii ri ao 5 24 Specification O RN 6 2 5 SPIMENSIONS enn a A A A E A e a fete 8 2 5 1 Dimensions with ceiling mount adapter ccooccccncicnncccnnnccnonccnnnrnnnnonnoncnnnncnnnncaroncrrnoncnnns 8 2 5 2 Dimensions with recessed ceiling mount adapter 444rnnnnnn nee eee nennen nennen 8 2 5 3 Dimension EPTZ 100 with wall mount bracket EPTZ 100 WLM ssec 9 2 5 4 Dimensions wall bracket EPTZ 100 WLM usesnssreennnsnnennnnnnnnnn nennen nnnnen nennen nnnnnenn 9 2 5 5 Dimension EPTZ 100 with ceiling pendant bracket EPTZ 100 CPM cemnseennnnn 10 2 5 6 Dimension ceiling pendant bracket EPT
31. ount adapter x 114 diameter camera module mm Details in dimension drawing 1 5 kg camera module incl adapter board speed dome camera connector board ceiling mount adapter in ceiling mount adapter user manual mounting accessories 7 EPTZ100_ma_en_rev03 doc 2 5 DIMENSIONS 2 5 1 Dimensions with ceiling mount adapter 170 202 114 2 5 2 Dimensions with recessed ceiling mount adapter 114 166 8 EPTZ100_ma_en_rev03 doc 2 5 3 Dimension EPTZ 100 with wall mount bracket EPTZ 100 WLM 169 5 140 aA y A D g Q O ol Tt al TA 240 EPTZ100_ma_en_rev03 doc 2 5 5 Dimension EPTZ 100 with ceiling pendant bracket EPTZ 100 CPM 500 EW p 2 5 6 Dimension ceiling pendant bracket EPTZ 100 CPM 2 300 Ol E o 10 EPTZ100_ma_en_rev03 doc 3 INSTALLATION 3 1 MECHANICAL 3 1 1 Ceiling mount The ceiling mount accessories are included in the EPTZ 100 package 1 Use the drilling template to mark the drilling holes e 2 Click the connector board into the ceiling adapter Follow the red arrow marks at board and ceiling adapter for correct position Connector board 3 Mount the ceiling adapter and connector board to the ceiling For the cables use either the side o
32. reflections on the bus for details please refer to chapter 3 2 3 The termination is done by DIP switch DS3 DS3 Termination ON Termination OFF 3 4 INITIAL START A ter finishing all installation steps power on the EPTZ 100 At power up EPTZ 100 will perform an initialization The communication settings will briefly appear on the screen Please check these information to ensure the correct DIP switch settings Example TYPE EPTZ100 Firmware 709M 809Q BAUDRATE 9600 RS 485 ID 1 PROTOCOL EVERFOCUS 4 OSD MENU SETUP 4 1 1 Operation in Setup Menu Start EPTZ menu If DVR Main monitor is selected DVR in LCD display CAM hold MENU If no DVR main monitor is selected MENU or GAM hold MENU or alternatively in both modes SHIFT hold PRESET gt 9 5 gt ENTER Switch between the settings JOYSTICK y 4 Enter submenus JOYSTICK gt in CAMERA gt ADVANCED SETUP IRIS Change the settings JOYSTICK EXIT OSD menu submenus Menu item EXIT RETURN gt JOYSTICK in CAMERA gt ADVANCED SETUP IRIS Note Exceptional commands are described in the OSD 2 3 EPTZ100_ma_en_rev03 doc 4 1 2 Menu Structure FOCUS SETUP MODE ZOOM TRK ZOOM SPEED D ZOOM DISP ZOOM MAG ZOOM POS INIT LENS INIT EXPOSURE SETUP BRIGHTNESS
33. reset tours EPTZ 100 provides 7 different preset tour modes All tours are defined in the OSD setup menu PATROL TOUR Preset tour with up to 16 selected presets ALL PRESET TOUR Preset tour with all available presets GROUP 1 TOUR Preset tour with presets 1 4 GROUP 2 TOUR Preset tour with presets 1 4 GROUP 3 TOUR Preset tour with presets 1 4 GROUP 4 TOUR Preset tour with presets 1 4 TOUR SCAN Preset tour with defined preset GROUPS POSITION gt number gt ENTER Camera 441 Position __ 1 132 Tour numbers 68 TOUR SCAN 69 PATROL TOUR 70 or 98 ALL PRESET TOUR 71 GROUP 1 TOUR 72 GROUP 2 TOUR 73 GROUP 3 TOUR 74 GROUP 4 TOUR 5 2 5 Pattern tours EPTZ 100 provides 4 programmed pattern tours with up to 10 minutes duration each The pattern tours are started with the POSITION key POSITION gt number gt ENTER Camera goto Position 0 192 Numbers 75 Pattern 1 76 Pattern 2 77 Pattern 3 78 Pattern 4 43 EPTZ100_ma_en_rev03 doc 5 2 6 Remote switching of EPTZ 100 output relay The EKB 500 keyboard provides the option to switch the output relay of EPTZ 100 On Off Switch relay ON F4 gt 1 gt ENTER Switch Alarm Out _ 1 8 OM Alternative POSITION gt 82 gt ENTER Switch relay OFF CLR F4 gt 1 gt ENTER oia Dut Alternative POSITION gt 81 gt ENTER 44 EPTZ100_ma_en_rev03 doc 6 APPENDIX A BASIC SETTINGS AT EKB 500 KEYBOARD The following chapter
34. resets 1 32 OFF no display of preset name PTZ POSITION ON show coordinates for pan and tilt in degrees and zoom ratio OFF no PTZ position display RETURN Returns to main menu 2 6 EPTZ100_ma_en_rev03 doc 4 1 6 Camera This menu provides the camera video settings CAMERA ZOOM SPEED ADVANCED SETTING RESCUE MODE BAUD RATE PARITY RETURN Zoom speed setup in 8 possible levels Level 1 slowest to Level 8 fastest Opens submenu for camera features following chapter Mode for recovering serial communication between speed dome and camera module This mode is not needed for normal setup Keep setting OFF For details consult APPENDIX C Troubleshooting Baudrate display for RESCUE MODE This parameter is not needed for normal setup For details consult APPENDIX C Troubleshooting Display of parity setting for RESCUE MODE This parameter is not needed for normal setup For details consult APPENDIX C Troubleshooting Returns to main menu 4 1 6 1 Advanced setting camera setup NOTE This menu and its submenus require an operation different from the other EPTZ 100 OSD menus Switch between the settings JOYSTICK y A Switch to submenu enter IRIS Leave the menu MAIN SETUP CAM TITLE WHITE BAL Menu item EXIT confirm with IRIS Alternative camera title display option Please leave this setting OFF and use CAMERA NAME in DISPLAY menu for editing displaying camera title White B
35. sceneries with back light only under normal light conditions the BLC may impair the image quality OFF BLC not active LOW MIDDLE HIGH Levels of BLC gain Set the level as low as possible to avoid overmodulation EPTZ 100 does not support this feature Please leave the setting on OFF Submenu for setup of focus modes and features ONE_PUSH The one push function focuses the lens after each pan tilt zoom operation and turns autofocus off after focusing This mode is recommended for most applications AUTO The AUTO mode enforces the lens to automatically adjust its focusing when either the object moves or the scene has changed NOTE The autofocus function requires adequate illumination of the scenery Especially in low lux environment it is recommended to use the One Push autofocus mode not the AUTO mode MANUAL Manual mode to finetune and obtain the optimum focusing In certain conditions such as weak contrast dark sceneries etc the autofocus function of the camera may not get the best focus position In such case the focus can be adjusted manually ZOOM TRK Zoom tracking with setting ON the lens tries to keep focus also during zoom in zoom out operation Dependencies zoom modes Focus One Push AUTO Manual Mode Action on port Ton off Ina Change in scene no action no action focusing focusing A Zooming focusing focusing focusing focusing focusing at stop at stop Go to Preset focusin
36. se OSD menu RETURN Return to SCAN menu GROUP2 similar setup as Group 1 GROUP3 similar setup as Group 1 GROUP4 similar setup as Group 1 32 EPTZ100_ma_en_rev03 doc TOUR SCAN Combined preset tour with selected GROUP tours GROUP1 ON Group included in tour OFF Groupi skipped in tour GROUP2 ON Group 2 included in tour OFF Group 2 skipped in tour GROUP3 ON Groups included in tour OFF Group3 skipped in tour GROUP4 ON Group 4 included in tour OFF Group4 skipped in tour SPEED Pant tilt speed for movement between preset positions range from 2 slowest to 180 fastest DWELL Dwell time at preset positions adjustable 1 45 seconds global setting for all presets RUN Start preset tour this function will close OSD menu RETURN Return to SCAN menu PATROL The PATROL tour is the most flexible preset tour with selected presets as well as individual speed and dwell time setting for each preset The maximum number of preset positions in this tour is 32 preset numbers 1 32 PRESET x SPEED DWELL RUN RETURN Select a preset 1 32 ON preset included in the tour OFF preset skipped in the tour Pant tilt speed for movement to this preset range from 2 slowest to 180 fastest Dwell time at selected preset position adjustable 1 45 seconds Start preset tour this function will close OSD menu Return to SCAN menu 33 EPTZ100_ma_en_rev03 doc PATTERN A pattern is a programmed course of camer
37. to be highly susceptible to interferences Basically the bus should be created by serial wiring star wiring is only permitted using signal distributors Maximum RS 485 bus cable length is 1200 m Both the first and the last device are normally 120 Ohm terminated in order to minimize line reflexions 1 ul woe Serial RS485 installation DS3 Termination switch ON af A LJ l 2 max am mak em DS3 Termination switch ON la Serial RS485 installation with connector boxes and stubs ad 120 Ohm al 5 40 Dist utor DS3 Termination DS3 Termination Dos Termination switch ON switch ON switch ON m E U Correct RS 485 star wiring with RS 485 distributor gg Incorrect RS 485 star wiring 16 EPTZ100_ma_en_rev03 doc 3 2 3 1 RS 485 installation with EKB 500 keyboard For connection to EKB 500 via RS 485 it is recommended to use the EKB 500 connector box The drawing below shows an installation example Please make sure that the wires are connected with correct polarity RS 485 port 1 or2 Hepending on setting Alternatively it is possible to connect the RS 485 wire directly to the keyboard by using a standard RJ45 plug The pin assignment is shown in the drawing below Port 2 12345678 RS485 RS485 Basic communication settings for EKB 500 are explained in Appendix A For further details please refer to the EKB 500 user manual 17 EPTZ100_ma_en_rev03 doc 3 2 3 2
38. utlet or a hole in the ceiling 4 Plug the dome module in the ceiling adapter Make sure that the position of the camera module connector fits the connector position of the connector board 5 After plug in turn the camera module some degrees clockwise to latch the camera module 6 Use the hex key to fix the camera position with the locking screw 11 EPTZ100_ma_en_rev03 doc 3 1 2 Recessed ceiling mount Recessed ceiling mount is possible at open ceilings A metal ring has to be mounted at ceiling side 1 Cut a 115mm 4 6 hole into the ceiling 2 Drill 3 screw holes for mounting in the ceiling Use the metal ring as template for drilling holes 115 3 Plug the connector board to the dome module and latch it by turning clockwise 4 Remove the clear dome cover and click the plastic cover ring at the dome cover with some pressure Mount the dome cover with ring to the camera module 5 Position the metal ring at top side of ceiling and mount the prepared speed dome module to the metal ring with 3 tapping screws 12 EPTZ100_ma_en_rev03 doc 3 1 3 Wall mount Wall mount requires the optional bracket EPTZ 100 WLM 1 Assemble the connector board to the bracket adapter by 3 M4 screws Follow the red arrow marks at both board and ceiling adapter for correct position 3 Mount the bracket adapter with connector board to the bracket 4 Mount the bracket to the wall 5 Plug the dome module in the ceiling a
39. witchers etc require cabling with 75 Ohm video cable e g RG 59 RG 12 and suitable BNC plugs Due to inappropriate absorbability 50 Ohm coax cable e g RG58 antenna cable and further types of coax cable are not suitable Make sure that the video input of the connected video device is terminated with 75 Ohm When interconnecting transmission lines twisted pair fibre optics radio to the speed dome ensure the accurate receiver calibration 3 2 2 Power EPTZ 100 is powered by 24 VAC voltage Connector is a 5 5 mm power cable socket Make sure that the used power supply complies with the power requirements of the speed dome 19 W max 24 VAC 1 A power source or higher current is recommended NOTE If the power supply is not located near the dome camera make sure that the installation cables have sufficient diameter otherwise the voltage drop over the power line will cause malfunction of the speed dome min 21 4 VAC at speed dome power input with active PTZ motors is required 24 VAC Transformer Mains power 110 24 VAC Power In VAC 230 VAC NOTE Do not connect the power until all installation steps are done 15 EPTZ100_ma_en_rev03 doc 3 2 3 RS 485 EPTZ 100 uses RS 485 simplex wiring the signal is transferred via a single twisted pair line CAT5 network cable is recommended UTP version unshielded is sufficient for normal application A shielded cable should be used if the installed cables are expected
Download Pdf Manuals
Related Search