Chief RSA315 project mount
Contents
1. 55378 2010 Milestone AV Technologies P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 a Duchossois Group Company Our Mounts Your Vision 11 10 INSTALLATION INSTRUCTIONS Continued IMPORTANT Some projector models may not be listed at this time Follow instructions for the various install options after you have determined which option matches your projector model WARNING IF A BRACKET IS TOO LOOSE THE PROJECTOR COULD BE DAMAGED OR A FASTENER COULD BE TWISTED OFF If a bracket seems loose move to try the next installation option 3 Verify if your projector model is listed for a recommended install option If your projector model is NOT listed start with Option 1 and work through options one at a time Projector Models Option 1 DELL Models 2300MP 5100MP Option 2 DELL Models 2100MP 2200MP 3200MP 3300MP HP Models sb21 xb31 Optoma Models H30 EP731 EP732 EP732B EP732E EP732H EP737 Option 3 DELL Model 4100MP 4 Place the correct spacers according to the option for your projector model e OPTION 1 Center three 3125 white spacers over three threaded inserts in bottom of projector e OPTION 2 Center three 4375 black spacers over three threaded inserts in bottom of projector e OPTION 3 Use six 3125 white spacers double stacked and place over three threaded inserts in bottom of projector 5 Place interface bracket on top of spacers aligning the mounting holes in the interface2. INSTALLATION INSTRUCTIONS SSB 315 SSM 315 SLB 315 and SLM 315 Interface Brackets SSB 315 SSM 315 SLB 315 and SLM 315 Interface Brackets are designed for use with Chief Series Projector Mounts See the specific installation instructions provided with the mount for additional installation information Unpack carton and verify kit contents If any listed parts are missing immediately contact a Chief Customer Service representative WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT substitute hardware Use only hardware supplied by manufacturer 1 Interface Bracket 3 Screw Phillips Flat Head Machine M3 x 16mm 4 10 24 Thumb Nuts 3 Screw Phillips Flat Head Machine M3 x 20mm 1 All Points Security Kit 3 Spacer Black 375 x 171 x 4375 6 Spacer White 375 x 194 x 3125 Towards front Towards front of projector of projector SLB 315 SLM 315 Note SSB style interface bracket connections are circled Note SSM style interface bracket connections are circled Only used when installing SLB SSB interface brackets NOTE Specific to SSB style and SSM style interface bracket installation All appropriate screws come pre installed in the circled locations above DO NOT attempt to substitute and USE ONLY this pre installed hardware for SSB style and SSM style interface bracket installation Installation Instructions WARNING OVE
3. R TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT over tighten screws when installing interface brackets NOTE Step 1 is only required when installing an SLB SSB interface bracket If an SLM SSM bracket is being installed proceed to step 2 1 Screw thumb screws onto 10 24 x 5 8 Phillips pan head screws DO NOT fully tighten thumb screws at this time 2 Turn projector upside down on a flat surface Chief is a registered trademark of Milestone AV Technologies All rights reserved F continued cH hs lt CONSUMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document AN Chief Manufacturing a products division of Milestone AV Technologies 8850 000158 Rev03 iC ae l f 8401 Eagle Creek Parkway Savage MN
4. bracket with the holes in the spacers 6 Select the correct fasteners according to the option for your projector model e OPTION 1 Use three M3 x 16mm screws and secure interface bracket to projector by threading screws through bracket and spacers and into threaded inserts in bottom of projector e OPTION 2 Use three M3 x 16mm screws and secure interface bracket to projector by threading screws through bracket and spacers and into threaded inserts in bottom of projector e OPTIONS Use three M3 x 20mm screws and secure interface bracket to projector by threading screws through bracket and spacers and into threaded inserts in bottom of projector 7 Tighten all fasteners at this time securing the bracket to the projector CHIEF
Download Pdf Manuals
Related Search