NEC EX231W
Contents
1. Please use a DisplayPort cable with a DisplayPort certified logo 2 The DisplayPort connector does not supply power to the connected component 3 When removing the DisplayPort cable hold down the top button to release the lock 7 Connect the power cord to the power outlet Figure C 1 NOTE Please refer to Caution section of this manual for proper selection of AC power cord 8 Turn on the monitor with the front power key and the computer Figure C 1 9 No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings For further adjustments use the following OSD controls e Auto Adjust Analog input only Refer to the Controls section of this User s Manual for a full description of these OSD controls NOTE If you have any problems please refer to the Troubleshooting section of this User s Manual ra E Power Key Figure C 1 Raise and Lower Monitor Screen The monitor may be raised or lowered To raise or lower screen place hands on each side of the monitor and lift or lower to the desired height Figure RL 1 NOTE Handle with care when raising or lowering the monitor screen Do not grasp the rear handle when raising or lowering the monitor It may cause pitching your finger between the stand and the monitor Figure RL 1 English 7 Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desire2. This is the brightness level that the monitor will go up to when the ambient light level is highest Select this setting when the room is at its brightest Select 1 or 3 in the AUTO BRIGHTNESS menu Figure 1 Then use the front Keys to move the cursor up to the BRIGHTNESS setting Choose the desired brightness level Figure 2 GHTNESS BRIGHTNESS CONTRAST CONTRAST AUTO CONTRAST AUTO CONTRAST ECO MODE ECO MODE AUTO BRIGHTNESS et Pot ae DY MODE Figure 1 Figure 2 2 Set the DARK level This is the level of brightness that the monitor will go down to when the ambient light level is low Make sure the room is at its darkest when setting this level Then use the front Keys to move the cursor up to the BRIGHTNESS setting Choose the desired brightness level Figure 3 BRIGHTNESS CONTRAST AUTO CONTRAST ECO MODE AUTO BRIGHTNESS DY MODE Figure 3 When the Auto Brightness function is enabled the Brightness level of the screen changes automatically according to the lighting conditions of the room Figure 4 100 BRIGHTNESS range BRIGHTNESS level set for the monitor to use when ambient lighting level is low BRIGHTNESS level set for the monitor to use when ambient lighting level is high Bright condition area A Td dark room bright condition bright E E Shes Screen Brightness value by Auto Brightness function Figure 4 Lb Border between bright and dim lighting conditions set at
3. Size Fine and Contrast settings a FULL MENU Switch to FULL MENU See page 11 for detailed information pic HUMAN SENSOR Shows current human sensing setting See page 12 for more details This function is adjusted threshold by FULL MENU CARBON SAVINGS eco Displays the estimated carbon savings information fi POWER Displays the current power consumption FULL MENU on oor Lil Ssp Au F HENI BARDEM Brightness ECO Function BRIGHTNESS Adjusts the overall image and background screen brightness lf ECO MODE is set to 1 or 2 a bar for CARBON FOOTPRINT will appear CONTRAST Adjusts the image brightness in relation to the background English 11 ECO MODE Decreases the power consumption by reducing the brightness level OFF Sets brightness variable from 0 to 100 ECO MODE 1 Sets brightness variable range from 0 to 80 This setting can adjust brightness to a range in which power is reduced to meet Energy Star measurement conditions ECO MODE 2 Sets brightness variable range from 0 to 40 This setting can adjust brightness to a range in which power is reduced by 30 compared to the maximum brightness setting When this function is set to ON a CARBON FOOTPRINT bar will appear alongside the brightness adjustment bar NOTE This function is disabled when DV mode is set for Dynamic AUTO BRIGHTNESS OFF No function AUTO BRIGHTNESS 1 Automatically adjusts the brightness to the opt
4. is not sized properly e Use the OSD Image Adjust controls to increase or decrease the H SIZE e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode No Video e Make certain the computer is not in a power saving mode touch the keyboard or mouse e Some video cards do not output video signal when monitor is turned OFF ON or disconnect connect from the AC power cord under low resolution with DisplayPort Brightness difference during multiple monitor usage e Change Auto Brightness to OFF and adjust brightness NOTE When Auto Brightness is set to ON the monitor automatically adjusts brightness to the environment When condition is difference monitor brightness will be difference English 17 Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room If the room is bright the monitor becomes correspondingly bright If the room is dim then the monitor will dim accordingly The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions The Auto Brightness function is set to 1 by default SETUP Use the following procedures to select the Brightness Range that the monitor will use when the Auto Brightness function is activated 1 Set the BRIGHTNESS level
5. solutions com greencompany in Europe http www nec display com in Japan or http www necdisplay com in USA Energy Saving This monitor features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Standard signal is sent to the monitor the Energy Saving mode is activated The monitor enters a single Energy Saving mode Normal Operation 23 W Default setting Blue Energy Saving Mode 0 37 W Off Mode 0 36 W WEEE Mark European Directive 2002 96 EC Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your NEC display products please follow the guidance of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself and NEC Outside the European Union The mark on electrical and electronic products only applies to the current European Union Member States If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method English 19
6. will not search the other video input port unless the monitor is turned on EXPANSION MODE Selects the zoom mode FULL The image is expanded to 1920 x 1080 regardless of the resolution ASPECT The image is expanded without changing the aspect ratio OFF TIMER Monitor will automatically power down when you have selected a predetermined amount of time Before powering off a message will appear on the screen asking if you want to delay the turn off time by 60 minutes Touch any OSD Key to delay the turn off time LED BRIGHTNESS You can adjust the Blue LED brightness DDC CI This function allows the DDC CI function ON or OFF FACTORY PRESET Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings Individual settings can be reset by touching the ECO RESET Key English 13 HENU Menu Tools TOOLS LANGUAGE OSD control menus are available in eight languages OSD TURN OFF The OSD control menu will stay on as long as it is in use In the OSD Turn Off submenu you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu OSD LOCK OUT This control completely locks out access to all OSD control functions without Brightness and Contrast When attempting to activate OSD controls while in the Lock Out mode a screen will appear indicating the OSD controls are locked out To activate the OSD Lock Out function touch INPUT SELECT then right control b
7. Directive 2004 108 EC EN 55022 EN 61000 3 2 NEC Display Solutions Ltd EN 61000 3 3 4 13 23 Shibaura SNN Tokyo 108 0023 Japan Council Directive 2009 125 EC EC No 1275 2008 EN 62301 2005 ENERGY STAR English 1 Canadian Department of Communications Compliance Statement DOC This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 FCC Information 1 Use the attached specified cables with the MultiSync EX231W L230NW color monitor so as not to interfere with radio and television reception 1 The power supply cord you use must have been approved by and comply with the safety standards of U S A and meet the following condition Power supply cord Non shield type 2 conductor Plug shape 2 Please use the supplied AC Adapter 3 Please use the supplied shielded video signal cable 15 pin mini D SUB to DVI A cable or DVI D to DVI D cable Use of other cables and adapters may cause interference with radio and television reception 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a resid
8. ISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit A This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems CAUTION Please use the power cord provided with this display in accordance with the table below If a power cord is not supplied with this equipment please contact your supplier For all other cases please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country European r Ae w a ss i When operating the Multisync EX231W monitor with its AC 125 240V power supply use a power supply cord that matches the power supply voltage of the AC power outlet being used NOTE This product can only be serviced in the country where it was purchased Registration Information Declaration Declaration of the Manufacturer We hereby certify that the colour monitor MultiSync and marked with EX231W L230NW is in compliance with Council Directive 2006 95 EC EN 60950 1 Council
9. NEC MultiSync EX231W User s Manual Index Wamng rs U 1 g ieee memceereatte aie ane settee Cie Were ert T te ny Oe ae ene ee English 1 Registration IMTOMMAL ON ensenen a av a English 1 Recommended USE sorae ra E E E ER English 3 fo a gy Leetonia ete ee ete re a a eee ee T English 5 TINS Fe SS Cet rna a E da ie ca nenelcia sy nice eae asf E A a A teavauaatenials English 6 COMMONS usiana ies fee a ees sae aed Sn dt ae English 10 SOC CIC AL ONS aiae sascha cece stins a E e a English 15 FEU aeee eee ne eee cree een re ere ee eee nee ree eRe eae eee ore ene ee err a cre ree ee eee English 16 MFOUDICSIOOUIN Gi sccceotuecaxeeuheaceedupecasienes pacers A N English 17 Using the Auto Brightness function cccceececcseeeeceescecceeeeeceeeeecseueeeseeeeceseeceseeessneeesenseeseass English 18 Manufacturer s Recycling and Energy Information cccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeesaaeeeeeeeaees English 19 WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AN CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE D
10. ard setting TEXT Setting that makes letters and lines crisp best suited for basic word processing and spreadsheets MOVIE Setting that boosts dark tones best suited for movies GAMING Setting that boosts whole tones best suited for games that use vivid colorful images PHOTO Setting that optimizes contrast best suited for still images DYNAMIC Setting that adjusts the brightness by detecting the screen s black areas and optimizes it English 12 Auto Adjust Image Controls Analog input only AUTO ADJUST Automatically adjusts the Image Position Horizontal Size and Fine settings AUTO CONTRAST Adjusts the image displayed to optimal settings LEFT RIGHT Controls Horizontal Image Position within the display area of the LCD DOWN UP Controls Vertical Image Position within the display area of the LCD H SIZE Adjusts the horizontal size by increasing or decreasing this setting FINE Improves focus clarity and image stability by increasing or decreasing this setting INPUT RESOLUTION Selects resolution s priority of input signal to one of the following pairs 1360 x 768 or 1280 x 768 or 1024 x 768 vertical resolution 768 1680 x 1050 or 1400 x 1050 vertical resolution 1050 Colour Control System Colour Control System Six colour presets select the desired colour setting SRGB and NATIVE colour presets are standard and cannot be changed 1 2 3 5 Increases or decreases Red Green or Blue c
11. ard should be completely seated in its slot e Front Power Switch and computer power switch should be in the ON position e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e Check the monitor and your display card with respect to compatibility and recommended settings e Check the signal cable connector for bent or pushed in pins e lf the front LED is dark blue check the status of the IPM mode see page 12 or Human sensor see page 11 Power Key does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor e When something is stuck on the bezel key becomes unresponsive Image Persistence e Please be aware that LCD Technology may experience a phenomenon known as Image Persistence Image Persistence occurs when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends displayin
12. asurement result below START TIME IPM SETTING Adjusts wait time to enter into to a lower power consumption level when on but not in use HUMAN SENSING The sensor on the front side of the monitor detects the movement of a person by using the HUMAN SENSING function THE HUMAN SENSING has three settings OFF No human sensing HUMAN SENSING 1 After it is detected that there is no person after a period of time the monitor shifts to low brightness mode automatically to reduce the power consumption When a person comes near the monitor again the monitor will automatically return to normal mode START TIME adjusts wait time to doing HUMAN SENSING 2 After it is detected that there is no person the monitor shifts to power saving mode automatically to reduce the power consumption When a person comes near the monitor again it comes back from the power saving mode and displays the images SENSOR SETTING HUMAN SENSING Adjusts threshold level of sensor result for Human detect condition and shows current sensor result in bottom side When measured sensor result is smaller than adjust threshould level it is detected that there is no person NOTE When OSD is closed human sensor starts to work START TIME HUMAN SENSING Adjusts wait time of enter to low Brightness mode or power saving mode when Human sensor detects no person DV MODE Dynamic Visual Mode allows you to select setting for Movie Photo Dynamic and etc STANDARD Stand
13. d Allows fast removal for good mobility and multi display setting Height adjustable 110 mm stand with tilt swivel and pivot add flexibility to your viewing preferences USB Pass through Adds excitement to your computing by connecting you to web cameras USB memory and more Simple MENU Allows you to quickly and easily access basic OSD controls A broad assortment of advanced adjustments are also available via the Full OSD Menu No Touch Auto Adjust automatically adjusts your optimal image settings upon initial power on Colour Control System Allows you to change between six colour settings on your display to match your personal preference NaViSet software offers an expanded and intuitive graphical interface allowing you to more easily adjust OSD display settings via mouse and keyboard The flat screen s crisp bright images and crystal clear text deliver a comfortable viewing experience ErgoDesign Features Enhance human ergonomics to improve the working environment and protect your health Examples include OSD controls for quick and easy image adjustments tilt base for preferred viewing angle small footprint and compliance with MPRII guidelines for lower emissions Plug and Play The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatically optimizing display per
14. d Figure TS 1 NOTE Handle with care when tilting the monitor screen Figure TS 1 Screen Rotation Before rotating the screen must be raised to the highest level to avoid running into the desk or pinching your fingers To raise the screen with one hand grip the top of the display by the handle using the other hand to grip the bottom Lift up to the highest position Figure RL 1 To rotate screen place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter clockwise from Portrait to Landscape Figure R 1 gt Figure R 1 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes 1 Disconnect all cables 2 Place hands on each side of the monitor and lift up to the highest position 3 Place monitor face down on a non abrasive surface Figure S 1 NOTE Handle with care when monitor facing down to avoid damage to the front control keys 4 Place one hand around the stand and one hand on the Quick Release Button Push the Quick Release Button in the direction indicated by the arrows Figure S 1 5 Lift up the stand to unlatch the upper hook and remove the stand Figure S 1 6 The monitor is now ready for mounting in an alternate manner 7 Connect the cables to the back of the monitor Figure S 1 English 8 Flexible Arm Installation This LCD monitor is designed for use with a flexible arm To mount the monito
15. ential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your dealer or an experienced radio TV technician for help If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 Declaration of Conformity This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any in
16. es a warning when there is no Horizontal or Vertical Sync After power is turned on or when there is a change of input signal the No Signal window will appear OUT OF RANGE This function gives a recommendation of the optimized resolution and refresh rate After the power is turned on or there is a change of input signal or if the video signal doesn t have proper timing the Out Of Range menu will appear NOTE It is possible to change the IPM settings or DVI Selection while the NO SIGNAL or OUT OF RANGE messages are displayed English 14 Specifications Monitor Specifications LCD Module Input Signal DVI DVI I Connector DisplayPort DisplayPort Connector Display Colours Synchronization Range Horizontal Vertical Viewing Angle Left Right Up Down Image Formation Time Resolutions Supported Active Landscape Horiz Display Area Vert Portrait Horiz Vert USB Hub I P Port Power Supply AC Adapter Power Maximun Operation Consumption Dimensions Landscape Portrait Height Adjustment Weight Environmental Considerations Operating Temperature Humidity Altitude Storage Temperature Humidity Altitude Diagonal Viewable Image Size Native Resolution Pixel Count Normal Operation MultiSync EX231W 58 42 cm 23 0 inches 58 42 cm 23 0 inches 1920 x 1080 Digital RGB Analog RGB Sync Digital RGB 16 777 216 31 5 kHz to 83 0 kHz Analog 31 5 kHz to 83 0 kH
17. factory L1 BRIGHTNESS level set for the monitor to use when ambient lighting level is high L1 gt Lb L2 BRIGHTNESS level set for the monitor to use when ambient lighting level is low L2 lt Lb L1 and L2 are the brightness levels set by you to compensate for changes in ambient lighting English 18 Manufacturer s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditioning or reclamation of material Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed To ensure the best recycling of our products NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display
18. fficient contrast Cleaning the LCD Panel When the liquid crystal panel is stained with dust or dirt please wipe with soft cloth gently Please do not rub the LCD panel with hard material Please do not apply pressure to the LCD surface Please do not use OA cleaner it will cause deterioration or discolor on the LCD surface Cleaning the Cabinet Unplug the power supply cord from the wall outlet Gently wipe the cabinet with a soft cloth To clean the cabinet dampen the cloth with a neutral detergent and water wipe the cabinet and follow with a dry cloth NOTE Many plastics are used on the surface of the cabinet DO NOT clean with benzene thinner alkaline detergent alcoholic system detergent glass cleaner wax polish cleaner soap powder or insecticide Do not touch rubber or vinyl to the cabinet for a long time These types of fluids and fabrics can cause the paint to deteriorate crack or peel English 4 Contents Your new NEC MultiSync LCD monitor box should contain the following e MultiSync LCD monitor e Power Cord e AC Adapter e Stand e Base stand e AC Adapter holder e Cable holder e Video Signal Cable 15 pin mini D SUB male to DVI A e Video Signal Cable DVI D to DVI D e USB Cable e Setup Manual DVI D to DVI D Base stand S etup Manuay AC Adapter holder Cable holder USB Cable Setup Manual Remember to save your original box and packing material to transport or ship the mo
19. footprint factor in the carbon saving calculation This initial setting is based on the OECD 2008 Edition CURRENCY SETTING Displays electricity pricing in 6 currency units CURRENCY CONVERT SETTING Displays electricity savings in kW hour US Currency is default NOTE This model s initial setting is Currency US and its Currency Convert setting 0 11 This setting can be changed by using the ECO information menu If you want to use the French setting please refer to steps below 1 Open menu by touching the Menu Key and select the ECO information menu using the left or right slide key 2 Select Currency setting by sliding the Up or Down key 3 The French currency unit is Euro You can adjust currency setting to Euro icon from US dollar icon by using the Left or Right key 4 Select Currency Convert Setting by using the Up or Down slide key 5 Adjust Currency Convert Setting by using the Right or Left slide key This initial Euro setting is Germany of OECD 2007 Edition Please check receipt of French s electricity prices or OECD data for French French of OECD 2007 Edition was 0 12 Information The Information menu indicates the current input display resolution horizontal and vertical frequency and polarity settings of the monitor The model and serial numbers of your monitor are also indicated OSD Warning OSD Warning menus disappear with MENU EXIT Key NO SIGNAL This function giv
20. formance IPM Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowering the air conditioning costs of the workplace Multiple Frequency Technology Automatically adjusts the monitor to the display card s scanning frequency thus displaying the resolution required FullScan Capability Allows you to use the entire screen area in most resolutions significantly expanding image size VESA Standard Mounting Interface Allows you to connect your monitor to any VESA standard third party mounting arm or bracket Environmental Impact The annual typical maximum operating carbon footprint of this monitor world wide average is approximately 28 2 kg calculated by rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power to Carbon conversion factor conversion factor is based on OECD publication of global CO2 emissions 2008 Edition This monitor has a manufacturing carbon footprint of approximately 13 1 kg Note The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors English 16 Troubleshooting No picture e The signal cable should be completely connected to the display card computer e The monitor does not support DisplayPort converter signal e The display c
21. g moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Message OUT OF RANGE is displayed screen is either blank or shows rough images only e Image is displayed only roughly pixels are missing and OSD warning OUT OF RANGE is displayed Either signal clock or resolution is too high Choose one of the supported modes e OSD warning OUT OF RANGE is displayed on a blank screen Signal frequency is out of range Choose one of the supported modes Image is unstable unfocused or swimming is apparent e Signal cable should be completely attached to the computer e Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine total When the display mode is changed the OSD Image Adjust settings may need to be re adjusted e Check the monitor and your display card with respect to compatibility and recommended signal timings e If your text is garbled change the video mode to non interlace and use 60Hz refresh rate LED on monitor is not lit no blue or amber colour can be seen e Power Switch should be in the ON position Power cord and AC adapter should be connected e Increase LED BRIGHTNESS adjustment Picture is not as bright e Make sure ECO MODE and AUTO BRIGHTNESS are turned off e Ifthe brightness fluctuates make sure AUTO BRIGHTNESS is turned off e Signal cable should be completely attached Display image
22. imal setting by detecting the brightness level of the environment AUTO BRIGHTNESS 2 Automatically adjusts the brightness to the optimal brightness setting based on the white display area The environmental brightness sensor Ambibright sensor has no function AUTO BRIGHTNESS 3 Automatically adjusts the brightness to the optimal setting based on the white display area and by using the AmbiBright sensor to detect the brightness level of the environment 1 Please refer to Page 18 for full Auto Brightness information NOTE This function is disabled when DV mode is set for Dynamic IPM SETTING The Intelligent Power Manager allows the monitor to enter into a power saving mode after a period of inactivity The IPM has two settings STANDARD Monitor enters power saving mode automatically when the input signal is lost SENSOR Monitor enters power saving mode automatically when the amount of surrounding light goes below the level determined by you The level can be adjusted in IPM sensor setting When in power saving mode the LED on the front of the monitor becomes dark blue When in power saving mode touch any of the front Keys except for POWER and INPUT to return to normal When the amount of surrounding light returns to normal levels the monitor will automatically return to normal mode SENSOR SETTING IPM SETTING Adjusts threshold level of ambient lighting sensor for detected dark condition and shows current sensor me
23. mm D 12 5 inches W x 21 5 24 7 inches H x 8 5 inches D 110 mm 4 3 inches Landscape condition 80 1 mm 3 2 inches Portrait condition 4 2 kg 9 3 lbs Without stand 2 8 kg 6 2 lbs 5 C to 35 C 41 F to 95 F 20 to 80 O to 6 562 Feet 0 to 2 000 m 10 C to 60 C 14 F to 140 F 10 to 85 O to 40 000 Feet 0 to 12 192 m 1 Interpolated Resolutions When resolutions are shown that are lower than the pixel count of the LCD module text may appear different This is normal and necessary for all current flat panel technologies when displaying non native resolutions full screen In flat panel technologies each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be done NOTE Technical specifications are subject to change without notice English 15 Features Lightweight Design The design of the display including a remarkably thin bezel and minimal stand components promotes lightweight for easier portability and desktop maneuvering Human Sensor Shifts to a lower power consumption level when a person leaves the monitor saving your monitor energy costs Touch Key Slide key Allows you to quickly and easily adjust all elements of your screen image by simply sliding your finger over the icons on the monitor bezel Redesigned OSD controls allow you to quickly and easily adjust all elements of your screen image Quick Release stan
24. n viewing the middle of the screen Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes The optimal distance is 50 cm Rest your eyes periodically by focusing on an object at least 20 feet away Blink often Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen If reflected light makes it hard for you to see your screen use an anti glare filter Adjust the monitor s brightness and contrast controls to enhance readability Use a document holder placed close to the screen Position whatever you are looking at most of the time the screen or reference material directly in front of you to minimize turning your head while you are typing Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects Get regular eye checkups Ergonomics To realize the maximum ergonomics benefits we recommend the following Adjust the Brightness until the background raster disappears Do not position the Contrast control to its maximum setting Use the preset Size and Position controls with standard signals Use the preset Colour Setting Use non interlaced signals with a vertical refresh rate between 60 75 Hz Do not use primary colour blue on a dark background as it is difficult to see and may produce eye fatigue to insu
25. nitor 1 Type of power cord included will depend on the where the LCD monitor is to be shipped English 5 Quick Start To attach the Base to the LCD stand 1 Place monitor face down on a non abrasive surface Figure 1 NOTE Handle with care when placing monitor face down to avoid damaging the front control keys 2 Put the upper hooks of the stand in the slot of the monitor then push stand into monitor in direction of the arrow as shown in Figure 1 and confirm that the stand is locked NOTE Handle with care when pulling the stand 3 Attach the base stand to stand and turn the connecting screw at the bottom of the base stand fully so that it is completely fixed Figure 2 NOTE Reverse this procedure if you need to re pack the monitor To attach the MultiSync LCD monitor to your computer system follow these instructions 1 Turn off the power to your computer 2 For PC or MAC with DVI digital output Connect the DVI signal cable to the connector of the display card in your system Figure A 1 Tighten all screws For PC with Analog output Connect the 15 pin mini D SUB to DVI A signal cable to the connector of the display card in your system Figure A 2 Tighten all screws For MAC Connect the Macintosh cable adapter to the computer then attach the 15 pin mini D SUB to DVI A signal cable to the Macintosh cable adapter Figure A 3 Tighten all screws For PC with DisplayPort output Connect the DisplayPort cable
26. olour depending upon which is selected The change in colour will appear on screen and the direction increase or decrease will be shown by the bars NATIVE Original colour presented by the LCD panel that is unadjustable sRGB sRGB mode dramatically improves the colour fidelity in the desktop environment by a single standard RGB colour space With this colour supported environment the operator could easily and confidently communicate colour without further colour management overhead in the most common situations NOTE When MOVIE GAMING or PHOTO is selected as the DV MODE NATIVE is selected automatically as the six colour preset and cannot be changed Tools DVI SELECTION This function selects the DVI input mode When the DVI selection has been changed you must restart your computer Touch Left or Right to select DIGITAL DVI digital input is available ANALOG DVI analog input is available VIDEO DETECT Selects the method of video detection when more than one computer is connected FIRST The video input has to be switched to FIRST mode When current video input signal is not present then the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically The monitor will not look for other video signals while the current video source is present NONE The Monitor
27. ot use monitor in high temperatured humid dusty or oily areas e Do not cover monitor and AC adapter e Do not touch LCD panel surface while transporting mounting and setting Applying pressure on the LCD panel can cause serious damage e To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks make sure to install the monitor in a stable location and take measures to prevent falling Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e When AC adapter is damaged e If liquid has been spilled or objects have fallen into the monitor e If the monitor has been exposed to rain or water e lf the monitor has been dropped or the cabinet damaged e lf the monitor does not operate normally by following operating instructions e If you notice any structural damage such as cracks or unnatural wobbling e lf glass is broken handle with care e lf monitor or glass is broken do not come in contact with the liquid crystal and handle with care e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor nono The power cable connector is the primary means of detaching the system from the power supply The monitor sh
28. ould be installed close to a power outlet which is easily accessible e Handle with care when transporting Save packaging for transporting e Carry the monitor holding the built in handle and bottom frames of the monitor e Do not carry holding only the stand e Image Persistence Please be aware that LCD Technology may experience a phenomenon known as Image Persistence Image Persistence occurs when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use English 3 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE SHOULDER AND NECK FATIGUE CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR For optimum performance allow 20 minutes for warm up Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly downward whe
29. r to a flexible arm 1 Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand 2 Using 4 screws attach the arm to the monitor Figure F 1 NOTE 1 The LCD monitor should only be used with an approved arm e g GS mark To meet the safety requirements the monitor must be mounted to an arm which ensures the necessary stability under consideration of the weight of the monitor 2 The mounting stand must be able to sustain at least 12 kg and be UL certified 12 on EP 4 x 12 mm with lock washer and flat washer Thickness of Bracket Arm 2 0 3 2 mm 4 Screws M4 Max Depth 9 5 mm Weight of LCD assembly 3 0 kg MAX Mm gt 100 mm Figure F 1 English 9 Controls OSD On Screen Display control keys on the front of the monitor function as follows You can access the OSD menu by touching your finger on any of the control keys To change signal input touch the INPUT SELECT Key To change ECO MODE touch the ECO RESET Key NOTE OSD must be closed in order to change signal input SELECT Button Ambibright Sensor Detects the level of ambient lighting allowing the monitor to make adjustments to various settings
30. resulting in a Human Sensor more comfortable viewing experience Do not cover this sensor LED Power INPUT SELECT Enters the OSD sub menu Activates the select function Changes the Input source No OSD condition MENU EXIT Opens OSD main menu Exits the OSD controls Exits to the OSD main menu Left Right Moves the highlighted area left right to select control menus Moves the bar left right to increase or decrease the adjustment Direct adjust of BRIGHTNESS No OSD condition Down Up Moves the highlighted area down up to select one of the controls Direct adjust of CONTRAST No OSD condition 8 ECO RESET Resets the highlighted control menu to the factory setting Switches the ECO MODE Activates Auto Adjust function if touched for 3 seconds No OSD condition and Analog input only NOTE When RESET is touched in the main and sub menu a warning window will appear allowing you to cancel the RESET function by touching the MENU Key When hot key function is OFF this function is disabled English 10 Simple MENU 4 gt BRIGHTNESS i AUTO ADJUST FULL MENU ue HUMAN SENSOR OFF 2 CARBON SAVINGS 999 999Kg 4 POWER 88 BRIGHTNESS Adjusts the overall image and background screen brightness lf ECO MODE is set to 1 or 2 a bar for CARBON FOOTPRINT will appear ECO MODE can be set by FULL MENU Ti AUTO ADJUST Analog input only Automatically adjusts the Image Position Horizontal
31. sociation D CERTIFIED English 2 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e The power supply cord you use must have been approved by and comply with the safety standards of your country Type HOSVV F 3G 0 75mm should be used in Europe e In U K use a BS approved power cord with molded plug having a black 5A fuse installed for use with this monitor e Do not place any objects onto the monitor and do not use the monitor outdoors e Use supplied AC Adapter Do not place any objects onto the AC Adapter and do not use the AC Adapter outdoors e Do not bend crimp or otherwise damage the power cord e Do n
32. terference received including interference that may cause undesired operation U S Responsible Party NEC Display Solutions of America Inc Address 500 Park Bivd Suite 1100 Itasca Illinois 60143 Tel No 630 467 3000 Type of Product Display Monitor Equipment Classification Class B Peripheral Models MultiSync EX231W L230NW FC We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules Windows is a registered trademark of Microsoft Corporation NEC is a registered trademark of NEC Corporation ENERGY STAR iS a U S registered trademark ErgoDesign is a registered trademark of NEC Display Solutions Ltd in Austria Benelux Denmark France Germany Italy Norway Spain Sweden U K NaViSet is a trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland MultiSync is a registered trademark of NEC Display Solutions Ltd in the countries of U K Italy Austria Netherlands Switzerland Sweden Spain Denmark Germany Norway and Finland All other brands and product names are trademarks or registered trademarks of their respective owners As an Enercy Star Partner NEC Display Solutions of America Inc has determined that this product meets the Enercy Star guidelines for energy efficiency The ENercy Star emblem does not represent EPA endorsement of any product or service DisplayPort is trademarks of Video Electronics Standards As
33. to the connector of the display card in your system Figure A 4 DVI signal cable Macintosh DisplayPort cable Figure A 1 Figure A 2 Cable Adapter Figure A 3 not included Figure A 4 not included NOTE Some Macintosh systems do not require a Macintosh cable adapter 3 Place hands on each side of the monitor to tilt the LCD panel 30 Tilt 30 degree angle and lift up to the highest position Figure B 1 4 Connect all cables to the appropriate connectors on the back of the monitor plug the captive power cord into the AC adapter Figure B 1 When using the USB cable connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer Figure B 1a If you can use the Highest stand position cord from the USB device use the downstream ports on the back Top side of the monitor 5 Place AC adapter holder and cable holder onto the stand Figure B 2 6 Position the Video Signal Cable and AC adapter between the holes on the cable holder as indicated in Figure B 2 Figure B 3 Position the AC adapter between the holes on the AC adapter holder as indicated in Figure B 2 DisplayPort USB upstream Power Cord Figure B 1 English 6 Figure B 1a Figure B 2 Figure B 3 NOTE 1
34. utton and hold down simultaneously To deactivate the OSD Lock Out touch INPUT SELECT then left control button and hold down simultaneously while in the OSD menu HOT KEY When this function is activated ECO Mode BRIGHTNESS and CONTRAST can be adjusted without entering the OSD menu by using the front keys ON The ECO keys switch ECO mode The Left or Right key adjust the brightness level The Down or Up keys adjust the contrast level OFF The ECO Left Right and Down Up keys are disabled when No OSD condition SIGNAL INFORMATION If you select ON monitor displays VIDEO INPUT MENU after changing Input Port If you select OFF monitor doesn t display VIDEO INPUT MENU after changing Input Port SENSOR INFORMATION If you select ON monitor displays HUMAN SENSOR ON message If you select OFF monitor doesn t display HUMAN SENSOR ON message KEY GUIDE If you select ON the Key Guide appears on screen when the OSD control menu is accessed The Key Guide will rotate when the OSD control menu is rotated FULL MENU OFF Shows Simple Menu see page 11 ON Shows Full Menu erp ECO Information CARBON SAVINGS Displays the estimated carbon savings information in kg COST Displays the electricity cost savings in balance INTEGRAL POWER Displays the multiple value of the power consumption CARBON CONVERT SETTING Adjusts the carbon
35. z Digital 56 0 Hz to 75 0 Hz 85 CR gt 10 75 85 CR gt 10 5 ms Typ 720 x 400 VGA text 640 x 480 60 Hz to 75 Hz 800 x 600 56 Hz to 75 Hz 832 x 624 75 Hz 1024 x 768 60 Hz to 75 Hz 1152 x 870 75 Hz 1280 x 1024 60 Hz to 75 Hz 1440 x 900 60 Hz 1400 x 1050 60 Hz to 75 Hz 1680 x 1050 60 Hz 1920 x 1080 60 HZ ee 509 2 mm 20 0 inches 286 4 mm 11 3 inches 286 4 mm 11 3 inches 509 2 mm 20 0 inches USB Specification Revision 2 0 Upstream 1 Downstream 1 Notes Active matrix thin film transistor TFT liquid crystal display LCD 0 265 mm dot pitch 250 cd m white luminance 1000 1 contrast ratio typical 25000 1 Contrast ratio Dynamic DVI HDCP 0 7 Vp p 75 ohm Separate sync TTL level Positive Negative Composite sync TTL level Positive Negative Sync on Green Video 0 7 Vp p and Sync Negative 0 3 Vp p DisplayPort Complies with Standard V1 1a applicable to HDCP Depends on display card used Automatically Automatically Automatically Some systems may not support all modes listed NEC DISPLAY SOLUTIONS cites recommended resolution for optimal display performance AC 100 240 V 50 60 Hz DC 19 V 2 1 A Type ADP 40ED A manufactured by DELTA ELECTRONICS 31 W 23 W Default setting 540 2 mm W x 401 3 511 3 mm H x 215 mm D 21 3 inches W x 15 8 20 1 inches H x 8 5 inches D 318 2 mm W x 547 2 627 3 mm H x 215
Download Pdf Manuals
Related Search