CyberPower Smart App Sinewave
Contents
1. PRIN FRONT REAR PANEL DESCRIPTION 1 Power Switch Master On Off switch for equipment connected to the UPS 2 Power on Indicator Indicate that the AC utility input power s condition is normal and that the UPS outlets are providing power free of surges and spikes 3 Multifunction LCD Readout An LCD that shows various UPS information using icons and messages 4 LCD Readout Toggle Button Used to select among a variety of information the LCD can display 5 Battery Backup amp Surge Protected Outlets This unit provides a total of seven outlets with battery backup and surge protection They ensure that connected equipment will keep an uninterrupted operation over a period of time during a power failure Critical Non critical It is possible to program the unit in a way so that the outle block marked as non Critical 4 ports will stop the provision of power to connected equipment after a certain period of time thus making more runtime available for the equipment connected on the outlets marked as Critical 3 ports In other words the user can establish runtime priority for certain connected equipment maximizing its availability during a prolonged power outage 6 Input Power Cord Heavy duty extra long power cord 7 Output Circuit Breaker The circuit breaker serves to provide o2. Remove the retaining screws Remove the two retaining screws of the cable connectors Put the new battery packs back into the compartment Tighten up the screws and replace the cable protection cover and the front panel NOTE Recharge the unit for at least 8 hours to ensure that the UPS performs to the expected runtimes LCD STATUS DEFINITION LOAD CAPACITY BATT CAPACITY a or 77 over NORMAL BATTERY AV SILENT LOAD FRAT aT we t Em Dal The LCD display indicates a variety of UPS operational conditions All descriptions apply when the UPS is plugged into the AC outlet and turned on or when the UPS is on battery than actual runtimes for low loads INPUT voltage meter This meter measures the AC voltage from the wall outlet The INPUT voltage readout is used to identify the input voltage information This can be used as a diagnostic tool to identify poor quality input power Units are listed in V Volts When the UPS connect to any equipment the AVR can provide a stable 110 120V power output In the event of a complete loss of power severe brownout or over voltage the UPS relies on its internal battery to back up to supply a consistent 110 120V output OUTPUT voltage meter The Output Voltage screen measures in real time the AC voltage that the UPS is providing to your connected equipment via the UPS outlets Units are listed in V Volts ESTIMATE RUN TIME The Estimated Runtime Screen display
3. CyberPower Reliability Quality Value Smart App Sinewave Series PR3000LCDRTXL2U User s Manual K01 0000066 00 IMPORTANT SAFETY WARNINGS This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate CAUTION The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection DO NOT plug the UPS into an outlet that is not grounded If you need to power drain this equipment turn off and unplug the unit CAUTION DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT Under no circumstances this unit should be used for medical applications involving life support equipment and or patient care CAUTION The battery can power hazardous components inside the unit even when the AC input power is disconnected CAUTION The UPS should be near the connected equipment and easily accessible CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants Please see specifications for acceptable temperature and humidity range CAUTION To reduce the risk of an electric shock do not remove the cover except to service the battery There are no user serviceable parts inside except for the battery
4. UPS be controlled and monitored via a network connection 15 EPO Emergency Power Off Port Allow for an emergency UPS Power Off from a remote location 16 Ground Stud Use the Ground Stud to ground the UPS 17 Extended Runtime XL Battery Pack Connector Provide a connection for additional CyberPower XL Battery Packs BATTERY REPLACEMENT Contact your dealer or email tech cpsww com Refer to replacement battery pack number RBP852 for the PRS3000LCDRTXL2U For model PR3000LCDRTXL2U can support model BPL48V75ART2U for external battery pack Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery Service the battery under the supervision of personnel knowledgeable of batteries and their precautions Servicing the battery should only be performed by trained personnel Replacement of batteries located in an OPERATOR ACCESS AREA CAUTION When replacing batteries replace with the same number of the following battery HR9 12 BB for PR3000LCDRTXL2U CAUTION Risk of Energy Hazard 12 V maximum 9 Ampere hour battery HR9 12 Before replacing batteries remove conductive jewelry such as chains wrist watches and rings High energy through conductive materials could cause severe burns CAUTION Risk of battery explosion if battery is replaced by an incorrect type Dispose of used battery according to the instructions CAUTION To reduce the risk of fire connect only to a circuit provided with 30 amperes maximum branc
5. referred to as this Warranty If you do not agree to the terms and conditions of this Warranty you should return the Product for a full refund prior to using it Who is Providing this Warranty CyberPower Systems USA Inc CyberPower provides this Limited Warranty What Does This Warranty Cover This warranty covers defects in materials and workmanship in the Product under normal use and conditions It also covers equipment that was connected to the Product and damaged because of the failure of the Product What is the Period of Coverage This warranty covers the Product for three years and connected equipment for as long as you own the Product Who Is Covered This warranty only covers the original purchaser Coverage ends if you sell or otherwise transfer the Product How Do You Get Service 1 Call us at 877 297 6937 or write to us at Cyber Power Systems USA Inc 4241 12th Ave E STE 400 Shakopee MN 55379 or send us an e mail message at claims cpsww com for instructions 2 When you contact CyberPower identify the Product the Purchase Date and the item s of Connected Equipment Have information on all applicable insurance or other resources of recovery payment that are available to the Initial Customer and Request a Claim Number 3 You must provide a dated Proof of Purchase receipt or other proof of the original purchase and provide a description of the defect 4 Pack and ship the product wit
6. OFF Then cover it and store it with the batteries fully charged Recharge the batteries every three months or so to ensure good battery capacity and long battery life further this might also prevent damage to the unit from an unlikely battery leakage 9 The unit provides one Primary Serial Port 1 Secondary Ser city and long battery life further this might also prevent damage to the unit from an unlikely battery leakage ial Port II and one USB port paired with the Primary Serial Port to allow connection and communication between the unit and any attached computers The Primary Serial Port I as well as its paired USB port allow for bi directional communication among the UPS and the primary connected computer running the PowerPanel Business Edition S W provided The UPS can control the computer s shutdown in case of an emergency and at the same time the computer can monitor the UPS and alter its various programmable parameters On the other hand secondary Serial Port Il only allows the UPS to initiate the connected computer s graceful auto shutdown in case of an emergency 10 EPO Emergency Power Off Port Use the provided gray cable to connect to a special EPO contact switch Follow the appropriate circuit diagram below to wire the cable to your EPO configuration The EPO remote switch is a switch installed in an outside area connected to the unit via an ordinary RJ 11 phone line In case of an emergency it can be used to immedi
7. CAUTION To avoid electrical shock turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer component CAUTION DO NOT USE WITH OR NEAR AQUARIUMS To reduce the risk of fire do not use with or near aquariums Condensation from the aquarium can come in contact with metal electrical contacts and cause the machine to short out INSTALLING YOUR UPS SYSTEM UNPACKING The box should contain the following 1 UPS Unit 1 User s Manual for UPS 2 Rack mount Brackets 2 Stands 2 Skids 1 Telephone Cable black 1 Emergency Power Off Cable gray 1 PowerPanel Business Edition Software CD 2 Serial Interface Cable DB 9 1 USB A B type cable 1 Warranty Registration Card OVERVIEW The PR3000LCDRTXL2U provides battery backup automatic voltage regulation AVR and optimal performance of computers and other network equipment by ensuring consistent sinewave power The PR3000LCDRTXL2U features 2060 Joules of surge protection and provides battery backup during power outages The PR3000LCDRTXL2U ensures consistent power to your computer system and its included software will automatically save your open files and shutdown your computer system during a utility power loss AUTOMATIC VOLTAGE REGULATOR AVR The PR3000LCDRTXL2U can stabiliz the consistent utility power The utility power may be damaging to important data and hardware but Automatic Voltage Regulation helps the computer n
8. ately cut off power from the UPS unit OPTION 1 USER SUPPLIED NORMALLY CLOSED SWITCH 8 eS 5 4 5 JUMPER E oo is e ep g ai a 8 cero switce eNlea leal aL UW PLUG o 0 GW Qe ree UW WwW lL 3 y G 7G or G SE e sm p l iee OF EN S N O EPO SWITCH RJ11 PLUG NO CONNECTION Dry connect is controlled by the PowerPanel Software please go to www cyberpowersystems com for free download NOTE Both USB and Serial cannot be used simultaneously The primary computer with PowerPanel Business Edition The equipment can read information via dry contact software connected to the UPS with either a serial cable or a USB cable BASIC OPERATION eS e QO D 4 O Sse oe og O o 9 IN N a A CG D A raira rao LH Ww o ray ae SI LW tO om gt c F L O A seser D
9. ay toggle key for 10 second TROUBLE SHOOTING C cn O e OOOO O ae Turn the UPS off and unplug at least one piece of equipment Wait Circuit breaker has tripped eae 10 seconds reset the circuit breaker by depressing the button and due to an overload then turn the UPS on Batteries are discharged Recharge the unit for at least 8 hours Outlet do not provide power to equipment Unit has been damaged by Contact CyberPower Systems about replacement batteries at a surge or spike tech cpsww com Uncritical outlets have turned off automatically Push the toggle button to make the uncritical outlets turn on due to an overload Battery not fully charged Recharge the battery by leaving the UPS plugged in The UPS does not perform expected runtime Battery is degraded Contact CyberPower Systems about replacement batteries at tech cpsww com The on off switch is designed to prevent Turn the UPS off Wait 10 seconds and then turn the damage by rapidly turning UPS on it off and on The UPS will not turn on THE UNIE Te NE eon ele The unit must be connected to a 110 120v outlet to an AC outlet CyberPower Systems about replacement batteries at The battery is worn out ad ecg ues MEAR tech cpsww com Mechanical problem Contact CyberPower Systems at tech cpsww com The serial cable or USB Connect the cable to the UPS unit You must use the cable that cable is not connected came with the unit The cable is connected to the wrong
10. communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference his own expense Shielded signal cables must be used with this product to ensure compliance with the Class A FCC limits The Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulation Cet appareil numerique de la class A respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada
11. ectively High Risk Activities CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums CyberPower does not authorize use of any Product in any High Risk Activities or with Aquariums ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT What is the Fine Print The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded CyberPower is the warrantor under this Limited Warranty For further information please feel free to contact CyberPower at Cyber Power Systems USA Inc 4241 12th Ave E STE 400 Shakopee MN 55379 call us at 877 297 6937 or send us an e mail message at clains cpsww com FCC Notice This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference that may cause undesired operation WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio
12. formation via a LAN connection 3 With the UPS off and unplugged connect your computer monitor and any externally powered data storage device Hard drive Tape drive etc into the outlets DO NOT plug a laser printer copier space heater vacuum paper shredder or other large electrical device into the UPS The power demands of these devices will overload and possibly damage the unit 4 To protect a fax telephone modem line or network cable connect the telephone or network cable from the wall jack outlet to the jack marked IN of the UPS Then connect a telephone cable or network cable from the jack marked OUT on the UPS to the modem computer telephone fax machine or network device 5 Press the power switch to turn the UPS on The Power On indicator light will illuminate If an overload is detected an audible alarm will sound and the UPS will emit one long beep In order to reset it turn the unit off and unplug some equipment from outlets Make sure your equipment carry a load current within the unit s safe range refer to the technical specifications and then turn the unit on 6 Your UPS is equipped with an auto charge feature When the UPS is plugged into an AC outlet the battery will be automatically charging even when the unit is switched off 7 To always maintain an optimal battery charge leave the UPS plugged into an AC outlet at all times 8 Before storing the UPS for an extended period of time turn the unit
13. h a dated Proof of Purchase receipt to CyberPower and if requested the item s of Connected Equipment a repair cost estimate for the damage to the Connected Equipment and all claim forms that CyberPower provides to you Show the Claim Number on the shipping label or include it with the product You must prepay all shipping costs you are responsible for packaging and shipment and you must pay the cost of the repair estimate How Long Do Have To Make A Claim All claims must be made within ten days of the occurrence What Will We Do To Correct Problems CyberPower will inspect and examine the Product If the Product is defective in material or workmanship CyberPower will repair or replace it at CyberPower s expense or if CyberPower is unable to or decides not to repair or replace the Product if defective within a reasonable time CyberPower will refund to you the full purchase price you paid for the Product purchase receipt showing price paid is required If it appears that our Product failed to protect any equipment plugged into it we will also send you forms for making your claim for the connected equipment We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value NOT REPLACEMENT COST of the equipment at of the time of the damage We will use Orion Blue Book or another a third party valuation guide or eBay craigslist or other source to establish that amount Our
14. h circuit overcurrent protection in accordance with the National Electric Code ANSI NFPA 70 CAUTION Use only the specified CyberPower replacement battery or battery pack See your dealer for details CAUTION The battery may present a risk of electrical shock Do not dispose of batteries in a fire as they may explode Follow all local ordinances regarding proper disposal of batteries CAUTION Do not open or mutilate the batteries Released electrolytes may be toxic and can be harmful to skin and eyes CAUTION A battery may present a high risk of short circuit current and electrical shock Take the following precautions before replacing the battery 1 Remove all watches rings or other metal objects 2 Only use tools with insulated handles 3 Do not lay tools or metal parts on top of battery or any terminals 4 Wear rubber gloves and boots 5 Determine if the battery is inadvertently grounded If inadvertently grounded remove source of ground CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK The likelinood of such shock will be reduced if such grounds are removed during installation and maintenance applicable to a UPS and a remote battery supply not having a grounded circuit BATTERY REPLACEMENT PROCEDURE Remove the front panel on the right side itself Disconnect the black and red wires from the battery Remove the retaining screws of the cable protection cover and then remove the cover
15. indicates a system fault error Please refer to the troubleshooting table for possible causes and solutions BATT CAPACITY meter BATT CAPACITY is shown as a bar chart each segment indicates approximately a 20 of battery capacity LOAD CAPACITY Load CAPACITY is shown as a bar chart each segment indicates approximately a 20 of load capacity LCD STATUS AND SETUP FUCTIONS 1 General Mode a Press the Display button to check the status of the UPS Pf tem it b Press and hold the Display Toggle button for 4 seconds Input Voltage Output Voltage 3 Output Frequency 5 If the machine is in the Battery Mode with active alarm it will become silent If the machine is in the Line Mode a self diagnostic test will take place c If the Display Toggle button remains untouched for over 30 seconds the Zz LCD backlight will turn off automatically in 5 Estimate Run Time mn 2 Set up Mode 6 LoadCapacty w M BE the Display Toggle button for 10 seconds to enter the UPS Battery Capacity y et Up Mode i Step 2 By pressing the Display toggle users can switch between setup e Centigrade functions Some User Configurable functions are as follows a Fahrenheit a Delay Time The time delay between switching from Battery Mode to Line Mode There are 9 different settings The default setting is 0 minutes b Battery Pack Numbers This function provides the estimated UPS runtime using various number
16. ing Relative Humidity 0 to 95 Non Condensing Communication PowerPanel Business Edition Windows 98 ME NT 2000 XP Vista Management Self Test Manual Self Test Auto Charger Auto Restart Yes COM Interface True RS232 x1 Contact Closure x1 You must use the cable included with the unit for the software 12V 9 0AHx4 Built in USB Interface Yes SNMP HTTP Network Slot Yes CYBERPOWER GREENPOWER UPS TECHNOLOGY GreenPower UPS The CyberPower GreenPower UPS cuts UPS energy costs by up to 75 compared to the conventional UPS circuits Conventional UPS systems pass power through a transformer to provide normal output voltage to protected devices By contrast the GreenPower UPS circuitry bypasses the transformer when utility power is normal significantly increasing the power efficiency of the UPS As a result a GreenPower UPS produces less heat and uses less energy reducing energy costs When utility power is abnormal the GreenPower UPS operates like a normal UPS Since utility power operates a normally 88 of the time the GreenPower UPS operates primarily in its cost cutting bypass mode LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARNTEE Read the following terms and conditions carefully before using the CyberPower PR3OOOLCDRTXL2U the Product By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and Connected Equipment Guarantee together
17. maximum liability is limited to 400 000 for PR3000LCDRTXL2U Who Pays For Shipping We pay when we send items to you you pay when you send items to us What Are Some Things This Warranty Does Not Cover 1 This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of the failure or the restoration of data or records or the reinstallation of software 2 This Warranty does not cover or apply to misuse modification operation or storage outside environmental limits of the Product or the equipment connected to it nor for damage while in transit or in storage nor if there has been improper operation or maintenance or use with items not designed or intended for use with the Product such as laser printers appliances aquariums medical or life support devices etc What Other Limitations Apply 1 This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and grounded outlets including compliance with electrical and safety codes of the most current electrical code without the use of any adapters or other connectors 2 The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product and not daisy chained together in serial fashion with any extension cords another Product or device similar to the Produc
18. ot experience dangerous voltage levels Automatic Voltage Regulator automatically regulates low or high voltages to keep equipment working at safe AC power levels 110 120V without switching to battery Your equipment can operate normally even meet the power problems such as shout brownouts and blackouts The unit s powerful sealed lead acid batteries will provide power only if the incoming voltage drops below 80V or increases above 150V SYSTEM BLOCK DIAGRAM EMI Input Output Suppressor Charger AC DC Inverter gt Normal Mode Battery Mode HARDWARE INSTALLATION GUIDE 1 Battery charge loss may occur during shipping and storage For the first time the UPS is used it s strongly recommended to charge batteries for at least eight hours is recommended to ensure that the batteries maximum charge capacity To recharge the batteries simply make the UPS plugs into an AC outlet 2 When you use the included software connect either the serial or the USB cable between the computer and the corresponding port on the UPS Note If the USB port is used the serial port will be disabled They cannot be used simultaneously The computer with the PowerPanel Business Edition S W connects to the USB port or the Serial port on the UPS It can control the operating schedule battery test outlet etc and get information on the UPS status However other computers with PowerPanel Business Edition S W can only get UPS status in
19. port Try another port of your computer PowerPanel Personal i Edition is inactive E a Shutdown your computer and turn the UPS off Wait 10 seconds ane pl IS nor providing and turn the UPS back on This should reset Battery s power the unit The serial cable is not the cable that was provided with the unit Additional troubleshooting information can be found at www cyberpowersystems com support htm TECHNICAL SPECIFICATIONS Model PR3000LCDRTXL2U Capacity VA 3000 Capacity Watts 2400 nput Plug Type NEMA L5 30P Nominal Input Voltage 125Vac nput Voltage Range 80Vac 150Vac Input Frequency Range 50 60Hz 3Hz auto sensing Output On Battery Output Voltage Pure Sine Wave at 120Vac 5 On Battery Output Frequency 50 60 0 1Hz Transfer Time Typical Overload Protection On Utility Circuit Breaker On Battery Internal Current Limiting Surge Protection and Filtering Lightning Surge Protection 2060 Joules Internet Ready DSL Phone FAX Modem Protection RJ11 RJ45 One In One Out Physical Output Receptacles 6 NEMA 5 20R 1 L5 30R Dimensions in 2U Rack 23 6 x 17 x 3 5 Weight Ib 92 4 Battery Sealed Maintenance Free Lead Acid Battery Extension Runtime Yes Hot Swappable External Battery Yes Warning Diagnostics ndicators Power On Wiring Fault LCD Display Using Battery AVR Load Level Battery Level Audible Alarms On Battery Low Battery Overload Environmental 32 F to 104 F 0 C to 40 C Operat
20. pplies for example to fluctuations in data transmission or reception by CATV or RF transmission or fluctuations or by transients in such transmission 3 Damage from any circumstance described as excluded above with respect to the Product 4 Damages from fire flood wind rain rising water leakage or breakage of plumbing abuse misuse or alteration of either the product or the Connected Equipment 5 CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee CyberPower excludes any liability for direct indirect special incidental or consequential damages whether for damage to or loss of property EXCEPT FOR AND ONLY FOR the specific limited agreement of CyberPower to provide certain warranty benefits regarding Connected Equipment under this Warranty loss of profits business interruption or loss of information or data NOTE Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you 6 The Product is not for use in high risk activities or with aquariums The Product is not designed or intended for use in hazardous environments requiring fail safe performance or for use in any circumstance in which the failure of the Product could lead directly to death personal injury or severe physical or property damage or that would affect operation or safety of any medical or life support device coll
21. s how many minutes of runtime can be expected of the UPS if it were to experience a power outage When runtime becomes shorted the battery capacity will decrease battery capacity bar indicator will be falling Note The number displayed may be less NORMAL icon This icon illuminates when the UPS is working under normal conditions BATTERY icon When there is a severe brownout or blackout this icon will appear followed by an alarm two short beeps indicating that the UPS is now working using its internal batteries Once the batteries are run out of power over a period of time a constant alarm will sound If this happens and main power has not been restored it is recommended that you save your files and turn off your equipment manually as soon as possible Automatic Voltage Regulation AVR icon This icon will appear when the unit is automatically regulating low or high AC input line voltage conditions without resulting to the use of battery power SILENT MODE icon This icon appearing indicates that the buzzer will not be beeping while in battery operating mode During Silent mode the unit s alarm does not sound until the Battery Capacity falls to lt 20 OVER LOAD icon This icon will appear followed by an alarm indicating that an overload condition has been reached To recover from the overload condition start unplugging your equipment from the UPS outlets until the icon disappears and the alarm stops FAULT icon When activated
22. s of battery packs The default setting is 0 c Static Frequency Tolerance There are 6 settings 1 2 4 6 8 10 and the default setting is 6 Functional description The setting may be adjusted to the quality of the electricity in use d Slew rate Also known as Dynamic Frequency Tolerance There are 5 different settings 0 25 0 5 1 2 4 Hz Sec The fault value is 4Hz sec Functional Description Slew Rate indicates the tolerance of a device in accepting frequency variance Lower Slew Rate results in less tolerance but better protection for the connected load and vice versa e Low Battery Shutdown Voltage This function will adjust the UPS shutdown point according to the battery s remaining capacity These programmable items are sorted by unit as in the following table Step 3 Press and hold the display toggle for 4 seconds When the icons blink the value of each item is changed by slightly pressing the toggle items nit Step 4 To save the value and return to general mode press and hold the Delay Time toggle for 4 seconds Battery Pack Numbers Static Frequency Tolerance Note If the UPS is left idle for over 30 seconds during setup it will turn s E off the backlight and return to general mode automatically Slew Rate Note If the user does not want to save the new settings and return to the general mode there are two methods 1 Wait for the backlight to turn off or 2 By pressing and holding the Displ
23. t surge suppressor or power tap Any such installation voids the Limited Warranty 3 The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license instruction manual or warnings provided with the Product and the equipment connected to it 4 The Product must have been used at all times within the limitations on the Product s VA capacity What are the Limitations The sole and exclusive remedies of the Initial Customer are those provided by this Warranty The Product was designed to eliminate disrupting and damaging effects of momentary less than 1ms voltage spikes or impulses from lightning or other power transients If it can be shown that a voltage spike lasting longer than 1ms has occurred the occurrence will be deemed outside the rated capabilities of the Product and the Limited Warranty is void CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following 1 Loss of or damage to data records or software or the restoration of data or records or the reinstallation of software 2 Damage from causes other than AC Power Line Transients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada transients surges or spikes on standard telephone land lines PBX telephone equipment lines or Base 10T Ethernet lines when properly installed and connected This exclusion a
24. utput overload and fault protection 8 Input Circuit Breaker The circuit breaker serves to provide input overload and fault protection wa BO 9 USB port to PC This is a connectivity port allowing communication and control among the UPS and the connected computer You should install on your computer the PowerPanel Business Edition software appropriate to the operating system you are using 10 Surge Protected Communication Ports RJ11 RJ45 These ports are being used to protect from various surge conditions the standard RJ 45 RJ 11 based ADSL LAN Phone Modem Lines cabling systems 11 Site Wire Fault Indicator This LED will illuminate to warn the user that a wiring problem exists within the AC receptacle such as a bad ground missing ground or reversed wiring If illuminated disconnect all equipment and contact an electrician to ensure outlet is properly wired 12 Serial Port Primary Serial port allow for bi directional communication among the UPS and the computer The UPS can control the computer s shutdown in case of an emergency and at the same time the computer can monitor the UPS and alter its various programmable parameters 13 Serial Port Il Secondary Serial Port Il allows the UPS to initiate the connected computer s graceful auto shutdown in case of an emergency 14 SNMP HTTP Network slot Remove the cover panel to install optional SNMP allowing your
Download Pdf Manuals
Related Search