Metra 99-5715 mounting kit
Contents
1. INSTALLATION INSTRUCTIONS FOR PART 99 5715 APPLICATIONS FORD Taurus MERCURY Sable 1996 1999 NOTE Metra s 70 5715 must be used with 1996 1997 models Metra s 70 5715 and 70 5716 must be used with 1998 1999 models 99 5 715 FEATURES e DIN Radio Provision KIT COMPONENTS A Integrated Mounting Kit TOOLS REQUIRED Torx Driver 86 5618 Head Unit Removal Keys Dremel Tool 22 www metraonline com A 1 800 221 0932 COPYRIGHT 2007 METRA ELECTRONICS CORPORATION 77 45 99 5715 TABLE OF CONTENTS Dash Disassembly FORD Taurus 1996 1999 7 MERCURY Sable 1996 1999 7 Kit Assembly DIN Radio Provision with 3 4 558 isa aa 5 Note Refer also to the instructions included with the aftermarket radio h f Mena I 99 5715 DASH DISASSEMBLY ANID KIT PREPARATION FORD Taurus and Mercury Sable 1996 1999 Disconnect the negative battery termi nal to prevent an accidental short cir cuit Using Metra s 86 5618 pull the factory radio climate control panel from the dash Disconnect the audio system connectors A blower motor switch connector vacuum hose harness damper door switch connec tor 0 and potentiometer connect2. g Kit and secure by bending the metal locking tabs down Slide the aftermarket head unit into the cage until secure Figure A Continue to final assembly FORD Taurus and Mercury Sable 1996 1999 Note Refer also to the instructions included with the aftermarket radio 1 Open the trunk remove 4 pop clips from the driver s side trunk liner and remove the liner Figure A Locate the factory tuner on the wall of the trunk and disconnect the speaker and antenna plugs it is NOT necessary to remove the tuner Figure B Plug the speaker extension lead into the unit speaker plug and the antenna exten sion lead into the unit antenna plug Slide the extension harness through the space in the back seat between the seat back and seat bottom Unclip the rocker trim tuck the extension harness under the carpet and stretch the harness to the back of the dash Replace the rocker trim when completed Splice the speaker leads on the extension harness into the rear of the aftermarket head unit Plug the factory wiring harnesses into the switch connectors previously mounted in step 2 and audio connectors on the back of the Integrated Mounting Kit located under the rear deck JNE 7 Melis 99 5715 KIT ASSEMBLY FORD Taurus and Mercury Sable 1996 1999 Note Refer also to the instructions included with the aftermarket radio 1 Re connect the battery terminal and test the unit climate controls and rear defroster for proper ope
3. or Remove the panel Figure Turn the factory climate control dials into a vertical position and pull the dials off see Fig A Remove 2 hex head screws securing the outer climate control switches and remove the switches Unclip the center climate control switch and remove the switch see Fig B Mount the switches to the back of the Integrated Mounting Kit using the same hex head screws see Fig C Holding the climate control dials in a vertical position insert the dials onto the posts of the mounted switches and secure see Fig D Continue kit preparation on next page 7 Meng 99 5715 PREPARATON FORD Taurus Mercury Sable 1996 1999 1 Remove 2 torx head screws secur ing the mounting clips to the sides of the factory radio climate control panel and remove the clips Figure A Mount the clips to the Integrated Mounting Kit with the same torx head screws Figure B 1 FOR MODELS WITH BENCH SEATS Cut and remove the shaded portion of the support rib located in the bottom left corner of the sub dash Figure A 2 FOR MODELS WITH BUCKET SEATS Relocate the module in the sub dash Cut and remove 1 4 from the top of each bottom mounting tab in the sub dash Continue to kit assembly JNE 7 Mens 99 5715 KIT ASSEMBLY DIN RADIO PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Slide the DIN cage into the Integrated Mountin
4. ration If the rear defroster does not work cut the black wire on the switch plug at position A and connect the wire extending from the rear defroster switch to ground see Fig A Snap the Integrated Mounting Kit assembly into the sub dash see Fig B Continue to final assembly 2 99 5715 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble in reverse order of disassembly using the 99 5715 Integrated Mounting Kit in place of the factory radio climate control panel FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Black Left Front White Power Antenna Blue Left F
5. ront White Black Turn On Blue White Right Rear Violet Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 5 99 5715 INSTRUCTIONS 1 800 221 0932 www metraonline com REV 12 27 07 COPYRIGHT 2007 METRA ELECTRONICS CORPORATION INST99 5715
Download Pdf Manuals
Related Search