Chief MPW6000B flat panel wall mount
Contents
1. Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall See Figure 6 CAUTION Keep hands and fingers away from all pinch points when moving the mount from retracted to extended position Faceplate Figure 6 4 Align mounting buttons on display with teardrop mounting holes in mount faceplate See Figure 7 5 Move display forward until all four mounting buttons are through teardrop mounting holes in faceplate and recessed area of mounting buttons is aligned with the lower area of teardrop mounting holes in faceplate 6 Lower display until the recessed area of all four mounting buttons is seated in the lower area of teardrop mounting holes in faceplate See Figure 7 7 Move latching flag to the UP position to secure display to mount assembly NOTE f desired install optional security screw and locknut provided The display can also be locked in the retracted position by installing the optional locking pin provided See Figure 8 Teardrop Mounting Hole 4 places Latching Flag Mounting Button On Display Faceplate Figure 7 Faceplate Figure 8 FELT PAD INSTALLATION Felt pads C are provided to protect the display from contact with the mount To install protective felt pads 1 Move display to fully extended position Installation Instructions MPW WARNING Keep hands and fingers away from al2. t te hexagonale Installation Instructions MPW TOOLS REQUIRED FOR INSTALLATION AND PARTS e x 5 32 4mm A N pn z B 2 n D 1 10 24 x 1 2 E 1 10 24 Installation Instructions MPW DIMENSIONS 089 89 008 1 H3NOHd XXXX MdMW SI H38IAQN H3QHO LNNOW 9NIHLLO VJQNVIN J31HO NOISN3IAIO XXXX GSW 40 ONIMVHG 8c 1VOINHO31 33S 39VH3 AV 9 NOILVTIVISNI OL H1d30 500 AV IdSIG dO MOVE OL Q3HOVLLLV LIJM OVH8 AOVAYALNI ALON LOTS al X w b V 1dSIG dO H3IN3O JLVNIXOHY ddY SZ 8 S309 1339VH8 HO AV IdSIG dO MOVE NO NOLLNG ONILNNOW 190 08481 1291 Figure 1 Installation Instructions MPW WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which the mount is being installed is capable of supporting five times the combined weight of the mount and all attachments MOUNT ASSEMBLY To attach the wall plate end caps 1 Slide one end cap F into each end of upper and lower wall plates ON MOUNT A See Figure 2 Figure 2 To attach the cable management clips 1 Pull mount face plate outward until access to rear of face plate can be achieved 2 Install two cable managemen
3. you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this mount does not exceed 125 Ibs 56 7 kg Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl
4. INSTALLATION INSTRUCTIONS Medium Flat Panel Wall Mount CHIEF MPW Our Mounts Your Vision MPW Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if
5. io Figure 9 CABLE MANAGEMENT Cable management clips for use with zip ties or similar devices are provided for cable routing To use cable management clips 1 Zip tie cable to cable clip B See Figure 10 2 Route cables down and under mount to display Figure 10 MPW Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a division of Milestone AV Technologies 8832 000214 RevB 2008 Milestone AV Technologies www chiefmfg com 10 08 USA International A 8401 Eagle Creek Parkway Savage MN 55378 P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA AI fp zs 27 AN AS P 486 755 8996 9226 F 486 755 8996 9217 3 a em 7 lt b I S Asia Pacific
6. l pinch points when moving the mounted display from the retracted to the extended position 2 Slowly rotate display to fully right position and identify the area of contact between the display and cabinet 3 Remove adhesive back from felt pad C and place pad onto display at identified point of contact 4 Slowly rotate display to fully left position and identify the area of contact between the display and cabinet 5 Remove adhesive back from felt pad C and place pad onto display at identified point of contact ADJUSTMENTS The mount is shipped with pre set tension for swing arm movement After extended use mount tension may need to be adjusted There are a total of 12 tension adjustment points on the mount See Figure 9 Six on mount top and six on mount bottom Points 1 through 6 control mount extension and retraction tension Points 1 and 6 control mount right left swing tension and points 3 and 4 control display left right rotation tension NOTE It is important that corresponding points are adjusted equally Example 1 and 6 2 and 5 3 and 4 and their corresponding adjustment points on mount bottom See Figure 9 To adjust mount tension 1 Determine which aspect of mount movement needs to be adjusted and locate appropriate adjustment Screws 2 Using the hex wrench provided tighten or loosen adjustment screws until desired tension is achieved See Figure 9 Decrease Tension Increase Tens
7. t clips B into each side of mount faceplate See Figure 3 Face Plate Face Plate Figure 3 MOUNT INSTALLATION WARNING The installer is responsible for verifying that the structure to which the mount is anchored will safely support five times the combined load of the mount and all attached components To install mount 1 Identify appropriate mounting location 2 Locate studs NOTE The MPW is designed to be mounted on 16 on center wood studs 3 Place mount assembly A against wall level mount and mark four pilot hole locations See Figure 4 4 Dril four 5 32 pilot holes at marked locations See Figure 4 Wall Studs A x 1 Figure 4 5 Place mount assembly A against wall and align mounting holes in mount assembly with pilot holes See Figure 5 6 Secure mount A to wall studs using four 1 4 x 2 lag screws and four flat washers MPW Installation Instructions Figure 5 INSTALL DISPLAY 1 Install interface bracket following the installation instructions included with the bracket WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 106 18 1kg ALWAYS use two people and proper lifting techniques when installing display 2 Lower latching flag See Figure 7 3
Download Pdf Manuals
Related Search