To Instructions - Lazy
Contents
1. 4 Please operate your bike according to the instructions Any damage malfunction loss or fault caused by misuse is not the responsibility of Zipper Bikes and will void the warranty 5 Unless permitted by Zipper Bikes or an approved distributor you may not change the original configuration of the bike doing so will void the warranty 6 The rights of interpretation of these statements are owned by Zipper Bikes Important Information 1 An electric bike should only be used by children with adult supervision 2 Please do not touch the battery or battery cables and the metal of the bike at the same time as this may cause a burst of discharge current which may cause harm or damage to the bike 3 Static starting riding uphill or against the wind operating over the maximum load and low tyre pressure will increase battery consumption and decrease the range If you want to get the best range possible 1 Pedal more 2 Reduce unnecessary braking and starting 3 Avoid overloading 4 Check the tyre pressure frequenily 4 Leaving the battery empty for a long time may damage the lifetime of the battery After riding please charge the battery if you do not use the battery for a long time please charge the battery to the half saturation state for 36 39V and take out the key It is recommended that you should use the bike at every 1 2 months 5 Please avoid excessive exposure of the e bike to the sun and rain such as leaving the bicyc2. Thank you for purchasing the Z2 Your new Zipper e bike is made with a high carbon steel frame making it light yet durable and comes with a lithium battery pre installed which has a range of up to 40km on a single charge The Z2 was designed for inner city commuting built with comfort and style in mind This e bike features a smart pedal assist system when you do the pedalling the electric motor works with you to add more power to the wheels make travelling much easier You can also use your electric bike like a simple scooter without pedalling just twist the throttle to go The brakes are pretty clever too not only do they act like a normal mechanical bicycle brake but they will cut power to the motor when applied making sure you get the most distance out of your battery life With a Zipper e bike you re in control whether you want to go for a long bike ride and only want help on those difficult hills or if you just need a 10 minute blast to work with your Zipper you ll be able to select just what you need The folding mechanism allows you to quickly store your bike with ease once you reach your destination which means no more disassembling your bicycle and carrying the wheels around We cannot guarantee the performance of our couriers if you receive a Zipper e bike which was damaged in transit please take a picture before assembly and send it to our email address support zipperbikes com before use and we ll send the replace
3. cause damage 3 Please do not exceed the maximum load for example carrying passengers or heavy objects 4 Please practice riding your bike in a safe area before riding it on a road 5 On the road never undertake a vehicle as it may not see you and turn left into your path Please pay particular attention to busses and large vehicles as it is difficult for raised cabins to see cyclists 6 Turn off the power using the key when stopped to conserve power 8 When pushing the bike remember to always turn off the power switch to avoid accidently rolling the throttle handle causing the e bike to start suddenly 9 All e bikes should only be stored indoors When Braking Loosen the throttle and use the brake only apply the back brake first and then front If you need to brake urgenily please use both the front and back brake at the same time Folding Lock Mechanism Ensure the latch is tightly locked in place before riding Rear Wheel Disabler Located at the back of the bike is the wheel disabler this has been designed to prevent the wheel from moving when locked which will foil people who attempt to steal the e bike zipper Assembling Your E Bike Adjusting The Front Braking System Check the right hand braking handle there should be full brake pressure when the lever is pressed halfway If the clearance spacing is different on the left and right pads you can adjust the adjusting screws on each brake arm until
4. the PAS assistance have no off normal deviation and loosening phenomenon abnormal the charger s short circuit phenomenon indicator light is flashing and 2 Charger is broken Replace with a new model charger that is the same 3 Charger is not connected socket is Reconnect the charger with new damaged socket Charging the battery shows Charger into state of burst discharge Check battery charge loop if it has the battery can t be charged 11
5. the distance of the two clearances are the same Loosen the spring tension adjusting screw then tighten or loosen the brake cable to make the clearances between the brake pad and the wheel rim to be approximately 1 5 2mm Tighten the tension screw when the clearances of the right hand side and left hand side pads are equal Adjusting The Rear Braking System Check the left brake lever the same way as checking the right brake lever adjusting the adjustment screw as needed If this does not work loosen the nut of the brake cable anchor bolt then loosen or tighten the cable until the proper tension is reached If this still does not work you can adjust the clearance fine adjustment screw and keep the clearance of the internal brake pad the same Adjust these parts until the rear brake works correctly Adjusting The Front V Brake Pad Adjust one side first and then adjust the other Please make sure the clearances between the brake pad and the wheel rim is approximately the same on both sides the optimal clearance width is around 1 5mm Tighten the nut after you have finished adjusting zipper Installing The Front Wheel Rest the front fork on the hub axle Use the included washers and nuts to tighten the wheel to the bike Please note the unique shape of the washers the latch must be inserted into the hole on the fork before tightening If you replace the wheels please tighten the nuts according to the recommended torque the rear whe
6. ctric lock is damaged Replace multifunction throttle power key including no lights LE etc Line conductor is broken Repair or replace line 3 Battery problem Check battery with voltmeter and ensure battery is charged If no power from battery replace No motor power after turning 1 Battery under voltage protection level Charge the battery Throttle is broken line conductor is Replace throttle repair line abnormal conductor Right and left brake is broken Replace right and left brake the key but lights etc are still working Controller and motor is broken or line Replace controller and motor conductor is abnormal maintain the line conductor problem battery has been charged incorrectly and needs replacing 2 Tyre pressure is not enough Blow up the tyres 3 When braking uninterrupted power Replace the brake maintain the line conductor Mechanical parts turn badly and Maintain the bad parts replace the Range is low 1 Battery voltage is too low not charged Charge the battery fully until charger enough lights turn blue or green If still a fault worn parts Cause resistance 5 More uphill drive against wind Correct bad drive mode read our frequent braking overloading best driving practices guide Battery is too old and broken Replace with the same model battery Power indicator light displays normal but when driven with assistance the motor supplies no power Pedal position the PAS assistance is Adjust
7. el torque should be no less than 30Nm while the front wheel torque should be no less than 18Nm Installing the Handlebars First lock the folding handlebar tube in place then insert the steering tube of the handlebars stand in front of the e bike and keep the front wheel between your legs hold the handle bar with both hands tightly and then adjust the handle bar angle preferably so that the handles are at a right angle with the handlebar tube the height of the handlebars should be adjusted to your personal size and preference Please do not extend the handlebar height over the maximum limit line Once the angle and height are correct be sure to correctly tighten the nut at the top of the handlebar tube and close the latch firmly dl 2X Installing the Seat Saddle Insert the seat post to your personal size and preference please do not extend the seat post height over the maximum limit line and then firmly tighten the seat post clamp with quick release zipper Adjusting The Chain Release the rear hub nut and adjust the position of the hub to adjust the chain tension the chain slack should be 10 15mm align the chain wheel with the rear sprocket so that they are in the same straight line and then tighten the rear hub nut Rotate the crank set counter clockwise the chain should have the appropriate tension and run smoothly Installing The Pedals Normally the pedals are marked with an L for left or an R fo
8. er Display Your Zipper bike has a built in battery indicator on the handlebars when the battery is full all five LEDs should light and when the indicator shows only two LEDS lit then the battery needs to be charged Sometimes the lights may flicker or turn off and on which is normal Charging Procedure 1 Only use the supplied charger and double check to make sure the output of your charger matches your battery 2 When charging connect the battery to the charger first and then plug the charger into the mains 3 When charging the power indicator light is red to indicate the battery is still charging When the battery is fully charged 3 6 hours the charging indicator lights will change from red to blue or green and the charger should be unplugged soon after Charging time should generally never exceed 8 hours IMPORTANT NEVER LEAVE A BATTERY CHARGING OVERNIGHT UNATTENDED 4 After charging you should pull the charger plug out of the mains and then disconnect the battery from the charger If you only wish to partially charge the battery for storage charging time should be reduced accordingly 5 If you smell burning during the charging process of the battery or the charger gets very hot please immediately stop charging and contact our customer service department or your local dealer for advice Battery 1 Please fully charge the battery before first use as described above 2 Please only use the supplied or designated chargers Otherwi
9. le outside In order to avoid electroplating of the parts and paint corruption please do not expose to high temperatures 6 Please check the braking performance regularly and do not pour oil into the braking mechanism Take extra caution when cycling in snow or minus temperatures as braking distances will be greatly increased 7 Before using your bike please check the all parts to ensure that everything is tight and intact to avoid damage or injury 8 The lithium battery will not cause environmental pollution but for the sake of safety please do not throw away batteries take your old battery to a battery recycling centre 9 Do not leave the battery near high temperatures and when charging please keep clear of flammable items if you remove the battery to charge it please place it on a non flammable surface 10 Please pay special attention where you see the below safety sign as these items may be hot or cause a shock A zipper Riding Precautions 1 Please don t use the throttle from stationary as this will use a lot of battery power Pedalling for around 3 5 cycles should be sufficient to avoid wasting the power and also protect the battery and motor You will feel the motor start automatically and then you can use the right hand throttle to increase or decrease assistance 2 This e bike can be exposed to light rain and snow but cannot wade into water Submerging the motor hub will cause the bike to stop and may
10. ment part Contents Table zipper Specifications User Guide Riding Precautions Assembling Your E Bike Maintenance Cleaning amp Regular Maintenance Troubleshooting Page 3 Page 4 Page 5 Page 6 Page 9 Page 10 Page 11 zipper Specifications Bike Specification LengthxWidthxHeight 1550x 1801170 LengthxWidthxHeight 800x300x580 mm mm Front And Rear Tyre Frame High Carbon Centre Distance mm Steel Motor Specification Rated Speed 280 RPM Rated Output Speed Controller Specification Cut Off Voltage 30 1V Burst Discharge 13 1A Current Charger Specification Input Voltage AC110 240V 0 8A 50 60HZ Charging Voltage And DC42 0V 2A Current Battery amp PAS Range 36V 9AH PAS And Motor 20 40km 10 C 50 C zipper User Guide As with all bicycles a Zipper e bike must be used and maintained properly in order to function correctly Please read this manual carefully as it contains vital safety information to ensure the continued performance of the bike If you have any queries please feel free to contact our customer service department Before Using Your Bike 1 Please charge the battery and pump the tyres before usage 2 Please observe national laws and local travel regulations violations of which are not the responsibility of Zipper Bikes 3 Our products are constantly being updated and changed therefore specifications may change slightly from those listed in this manual
11. r maintenance Drop a little oil onto the chain and apply drops every month 3 Adjust the rear ends of the chain Loosen the nut adjust the rear wheels front and rear position as needed to achieve the chains proper tightness the middle position of the chain if pushed down with your finger should only drop 10 15mm 4 Pay attention to the front and rear brake blocks if worn they should be promptly replaced to avoid loss of braking and wearing the aluminium ring zipper Cleaning amp Regular Maintenance Clean using a soft cloth Do not apply water directly to rear drum brake motor and hubs to avoid performance drop or shortening of life expectancy Do not use steam a hose pipe or high pressure water gun to clean Maintenance Schedule 60 Days 180 Days 1 1 Before each ride check whether tyre pressure is appropriate Normally the pressure is 125KPa for front wheel and 175KPa for the rear wheel 1 2 Any cracking or abnormal wear on the tyres 1 3 Any nails stones or glass stuck inside the tyres 2 Brakes work normally 3 Any damage on the charger and power cable BR 5 4 Front and rear hub nut tightened Throttle and turning O A O A mechanism parts loose or worn 6 es E Bikes check locking mechanism is secured 8 Crank arm worn out Smooth rotation Ll 9 Wheel spokes loose or broken O Check A Adjust Replace V Lubricating 10 zipper Troubleshooting No power after turning the 1 Ele
12. r right if they are not marked then they can be used on either side Please install accordingly otherwise the crank arm can be damaged Installing The Front Mudquard The headlamp comes pre installed however to attach the mudguard this must be loosened Remove the nut on the back of the head tube pass the mudguard over the tyre and hook the latch onto the bolt then retighten the nut both the headlamp and mudguard should now be in place The mudguard spokes attach to the front fork and are tightened into place by using the included washer and bolts onto the front wheel hub Charging The Battery This e bike comes with a built in battery to ensure that the power will not cut out unexpectedly Please read the following page on maintenance carefully this e bike is not a toy qu nn gt w 7 T wa TP Sa A LIN si Y N AN Le S zipper Maintenance Charger 1 Do not use the charger in places of heat excessive smoke and dust moisture and direct sunlight 2 When charging please keep the charger in a well ventilated room 3 Do not allow any liquid near the charger and do not insert any metal items 4 Do not drop impact or try to dismantle the charger 5 Do not attempt to repair a broken charger yourself charger replacements are available to purchase 6 Do not leave a battery charging unattended charging should be done while supervised and away from valuables pets children and flammable items Pow
13. se damage may occur to the battery and other related accessories which could result in an accident Any damage loss or fault arising from incorrect charging procedure or from using the wrong charger will be borne by the purchaser 3 The battery can be charged while inside the bike Some models can also be removed from the bike for charging The battery will need using cycled around 8 10 times before it reaches optimum performance and capacity 4 Be careful that the metal ports at the end of the battery box or connecting leads do not touch any other metal as this can cause a short circuit particular attention should be made with folding bikes 5 Do not drop impact or try to dismantle the battery 6 Do not use the battery for long periods of time under sun exposure or hot temperatures If you don t use your electric bike for a long period of time please charge it every two months charging to half capacity is considered efficient 7 Ensure water does not enter the batteries charging port 8 When discarding unwanted batteries first discharge the battery to zero voltage Never put into a fire Mechanical Parts 1 Fastening components 1 1 The handlebar head tube and saddle tube must be locked with 18Nm torque 1 2 Locking force of 15 17 KGF is required on quick disassembly parts 1 3 The front wheel nut locking torque needs to reach 18Nm and the rear needs to reach 30Nm 2 Lubrication The chain flywheel and headsets need regula
Download Pdf Manuals
Related Search