User Manual
Contents
1. 25 Introduction Thank You for Choosing SmartLabs IPTV STB Please read this user guide carefully before using the digital interactive televi sion IPTV set top box STB This guide contains the information about the following models of IPTV STB SML 272 SD SML 282 HD Base SML 292 HD Premium Note that particular features of your device are optional Your device may differ from the device shown in pictures in this guide The guide provides the description of all possible functions and options of SmartLabs IPTV STB The functions and slots available in your device and supplied accessories are fully determined by the service provider Your service provider will also give you another user guide or manual with the information on how to use the device to get access to IPTV services Serial Number and MAC Address of STB Serial Number and MAC Address of STB are written at the bottom panel of IPTV STB Using This Guide Further in this guide the information which is strongly recommended to be read is marked with the following icons Attention Possible situations of incorrect usage of the device which can provoke damage of IPTB STB or other devices and accessories T Note Additional information on the device usage peculiarities Usage Conditions 1 Use your IPTV STB indoors only The air temperature should be no higher than 40 C and the relative humidity should be between 20 90 without cond2. Note To control the device placed out of the direct visibility range with the y IR remote control use the external IR receiver if the device has the appro priate slot Connect the external IR remote control to IPTV STB and fix the external IR receiver in the direct visibility range of the device If your device is supplied with the RF remote control you do not need to place IPTV STB in the direct visibility range to control the device Keep the following conditions when installing the device 1 Place IPTV STB on a flat surface 2 Do not place the device on slick surfaces where there is a risk of vibra tion fall or other damages of IPTV STB 3 Do not mount the device on soft surfaces like bed carpet etc Because it impedes access for air and normal ventilation of the device This can cause overheating or damage of the device 4 Do not cover the device 5 Do not shield the ventilation holes in the device s enclosure located at the top panel of the device 6 When mounting the device leave at least 10 cm of free space from each panel of the device Do not place IPTV STB in closed cupboards and Caves 7 Donot place IPTB STB on surfaces which can heat for instance on boosters 8 Do not place various things on the device 9 To avoid damage of the power adapter s cable place the cable so that it is not pressed pinched or mechanically affected in another way Using IPTV STB Packaging IPTV STB
3. Power supply Ethernet cable AV video cable 8xRCA YPbPr video cable 8xRCA YPbPr Audio cable 5xRCA HDMI cable 1 8 m Remote control AAA batteries 2 pcs HDD connection kit User guide Warranty card Package 12V 1 2A Optional Optional Optional IR or RF Optional Optional Optional Optional IR or RF 12V 2 0A Optional Optional Optional IR or RF Connecting to Devices Connect your IPTV STB to a TV set speakers if any and the Internet accord ing to one of the following schemes 866 a mcooog To an Internet To a TV set or AV Power supply router receiver 220 V The connection scheme via HDMI 696 Power supply To an Internet router 220 V O H LI To a TV set or audio To a TV set system The connection scheme via the composite video slot RCA and stereo audio slot RCA E 9 To an Internet router To a TV set or audio system Power supply 220 V To an audio receiver or To a TV set audio system if any The connection scheme via the component video slot YPbPr and audio slot RCA or S PDIF You can also connect additional devices to your IPTV STB e Microphone Note The list of compatible microphones is available on the IPTV STB manu y facturer s web site www smartlabs tv iptvstb e 2 5 SATA in
4. Co LTD Assembling factory s address 35 East Mianxing Road High Tech Park Mianyang Sichuan China 25
5. terms of this agreement SmartLabs LLC and your service provider jointly grant you a non exclusive non transferable license without the right of sub license to use all software included with the device or subsequently provided to you and all documentation solely for your noncommercial use and solely in connection with your use of the device The device manufacturer does not provide any additional warranties regarding software installation The device manufacturer is not responsible for defects and errors which can be present in software and the device compliance to your functional requirements and needs The device manufacturer is not responsible for possible loss of profits activity cease money information loss or other kinds of losses which can be caused by using or the inability of using the installed software After the agreement is over you must return the device accessories and documentation to your service provider Copyright Notice Company and product names mentioned in this guide may be trademarks registered trademarks or served marks of the appropriate right holders HDMI HDCP Dolby AC 3 standards are used in the device on the appropri ate licenses given by its right holders SmartLabs LLC has the appropriate licenses to use these standards No part of this guide except the Warranty section can be considered as additional warranty commitment SmartLabs LLC is able to change improve any product described
6. the settings menu Opens the application profiles menu if supported by the service provider 17 Installation of the Hard Disk HDD The SML 292 HD Premium model allows you to install an internal hard disk into the device Hard disk is not included with the accessories You can purchase the disk separately HDD Requirements e Size 2 5 e Thickness 7 9 5 12 mm To install 7 or 9 5 mm disk use the appropriate plastic handle shipped with the box e SATA 300 connection slot and data transmission e SATA COMBO connector type SATA Data SATA Power e Recommended rotation speed 5400 rev min e Upto 1 TB volume When choosing the HDD model for your IPTV STB you may use the recom mended HDD model list from the device manufacturer which is available on the Web site www smartlabs tv iptvstbdfg The IPTB STB s manufacturer does not recommend you to use HDD with more than 5400 rev min speed because IPTV STB s enclosure will overheat If you install HDD with more than 5400 rev min speed HDD will work out of the esti mated recommended temperature mode which can decrease both the device and HDD s life time Attention Before you install remove HDD switch off the device and discon nect it from power supply Install the disk as it is shown in the picture 18 Switch off the device and disconnect it from the wall outlet Turn the device upside down To prevent scratching the glance sur faces put it on a fabric l
7. 500mA Ethernet TOBASE T 100BASE TX Slot RJ45 Composite video output CVBS Slot 1xRCA Component video output YPbPr RGB Slot 3xRCA Multimedia output HDMI 1 3a with HDCP Slot HDMI Stereo audio output Slot 2xRCA S PDIF Microphone inputs pcs Slot mini jack 3 5 mm IR RF Optional Optional Optional Optional Up to 2 IR RF 150 150 55 290 230 80 Optional Optional Optional Up to 2 IR RF Optional 2 21 External IR receiver Slot mini jack 3 5 mm Supported video formats Maximum supported definition Supported output video formats for CVBS Aspect ratio Play modes Analog video formats Digital audio formats Microphone types supported at mini jack 3 5 mm inputs 22 Optional Optional Optional Video MPEG 2 ISO IEC 13818 MPEG 4 AVC H 264 H 263 HDMI output up to 1080p YPbPr RGB output up to 1080i CVBS output up to 576i PAL SECAM NTSC 4 3 16 9 Audio Analog output Stereo Digital output Bypass Stereo Stereo MPEG Layer 1 2 3 PCM AC3 AAC Dynamic microphones Licenses and Certificates Licensing Agreement By using the software in your IPTV STB you agree to be bound by the terms of this agreement If you do not agree to be bound by the terms of the agree ment you must immediately cease all use of the device and return the device all accessories and documentation to your service provider Subject to
8. A lt gt V smarftlabs the smart way to your customers User Guide IPTV Set Top Box SML 272 SD SML 282 HD Base SML 292 HD Premium Contents CONTENTO aes 2 INTE 9 88 xq QT 3 Thank You for Choosing SmartLabs IPTV STB 3 Serial Number and MAC Address of STB 0cccccseseeeeeeeeneeees 3 Using This OBI rente metta tese adepti nito at EE uds 3 Usage a elcre o g cee ee eee OO T 3 au 630 seer seer ti sce ornate see cate soe Gee cree T A E 5 e AN INN eaa E E ele 5 puero RR 5 BECA TB T PACE ON ereer n T Connecting to CVC CS E 8 Indicators and SIOUS BRENNEN RE 10 Starting the Rd 13 Using the Remote Control ccccccsscccsseeeceeseeceeseeeseeeeessaeees 13 Remote Control Buttons Specification 16 Installation of the Hard Disk HDD cccceccceseeeeeeeeeeeeeneeees 18 Installation of the Flash Drive USB Flash 20 TECHNICAL CHARACTERISTICS ccccccccccseseeeseeseeseeeeeseeeeenes 20 LEICENSESANDCERTIFICALTES tatione zip t ra dedubiu Roles spon 23 Licensing Agreement ssesssesssesseeeeeee nennen nennen 23 CoDVFIght NOCE s ecdesia iu dao mue AAN 23 Standards and Certificates cccccccccseceeeeeeeeeeseeeeeeeeeeeseeeeeens 24 UCET
9. aying Remove the HDD cover by pressing 2 locks at the same time Attention To install 12 mm disk carefully cut off the lug at the internal side of the HDD cover A plastic handle is not required in this case Take 2 screws and a handle from the HDD connection kit Fix screws as it is shown in the picture Plug in the disk to the slot using the handle as it is shown in the picture 19 Close the HDD cover so that both locks click To remove the internal HDD from the STB perform the installation actions in the reverse order For more information on how to use the hard disk connected to IPTV STB see the documentation obtained from your service provider Installation of the Flash Drive USB Flash Flash drive is not included with the accessories You can purchase it separately Connect a Flash drive to a USB slot located at the back or side panel of the device see panel pictures For more information on how to use a Flash drive in IPTV STB see the docu mentation obtained from your service provider Technical Characteristics Basic parameters HDD SATA 2 5 connection possibility ar Slot SATA HDD IR receiver Protocol RC5 RC7 Carrier frequency 37 9 kHz IR RF IR RF IR RF 20 RF receiver Frequency RF433 MHz Device dimensions L W H mm Package dimensions L W H mm Inputs and Outputs USB 2 0 at the back panel A type 5V 500mA USB 2 0 at the side panel A type 5V
10. e direct visibility range from the device Usually it is an internal IR receiver having a special window to receive signals located at the front panel of the device If your IPTV STB has a slot for an external IR receiver you can fix the receiver in a suitable place and aim the Remote Control to it to control the device see Connecting External IR Receiver for IR Remote Control RF Remote Control is a radio frequency remote control which does not re quire the direct visibility range from the device RF Remote Control works in a range of 50 m of direct visibility and can also overcome small obstacles thin walls etc however in this case the action radius considerably decreases 13 Installation of Batteries to the Remote Control Two batteries of the AAA type are used in IR and RF Remote Control Put the batteries into Remote Control like it is shown in the picture e Remove the cover from the batteries compartment e Insert batteries keeping the correct polarity Close the batteries compartment cover When inserting or replacing batteries in Remote Control keep the following conditions 1 Strictly keep the batteries polarity 2 Do not use old and new batteries at the same time 3 Do nottry to charge batteries 4 Insert both batteries of the same manufacturer and model Connecting the RF Remote Control If your device is equipped with the RF Remote Control you should connect it to the IPTV STB which you are go
11. ensation 10 11 Use the IPTV STB only with the power adapter supplied with your device Make sure that the power supply standard approved in your country is compatible with the power supply standard used in the power adapter See the Technical Specification section Power Adapter If the power adapter is not compatible with the power supply standard used in your country contact the service provider Do not allow water or other liquids rain or high humidity to affect the de vice to decrease the risk of fire or current rush Do not put the device into water Do not use the device in those places where the IPTV STB can contact with liquid or steam If this occurs im mediately turn off the device and disconnect from the electricity network Contact the service provider on this accident Do not put the device into direct sun rays Do not place the device near the open fire or heating radiators Do not allow vibration or shake the device Do not use the device in dusty rooms If lightning is expected or you are not going to use IPTV STB for a long time disconnect the device from the wall outlet unplug the Ethernet video audio cables from it This measure will help to protect IPTV STB from damage due to lightning and power surges If you use IPTB STB with a plasma TV set do not leave the picture on for more than 5 minutes Due to plasma s constructive peculiarities a static picture left for a long time can damage the displa
12. in this guide and also the guide itself without preliminary notice SmartLabs LLC No part of this document can be reprinted republished without a preliminary agreement with SmartLabs LLC 23 Standards and Certificates The device manufacturer does not guarantee absence of clutters generated by the device To eliminate possible clutters do the following 1 Enlarge the distance between IPTV STB and other devices and equip ment 2 Connect the equipment using another scheme 3 Consult with your service provider Conformity IPTV STB is complied with TU 6582 001 83102005 2010 and has the appropriate ROHS certificate Electrical Safety Device SML 272 SD SML 282 HD Base SML 292 HD Premium Electrical Safety Class III 24 Warranty 1 Providing the warranty A warranty for your IPTV STB is offered by your service provider The warranty period and conditions of service are determined by your ser vice provider In case your IPTV STB requires servicing please contact your service pro vider directly 2 Warranty card A 49 NM smartlabs the smart way to your customers Warranty Card Device Serial Number Warranty Before Sales Date 3 Information on the manufacturer Company SmartLabs LLC Address 127521 Moscow 72 Oktyabrskaya street telephone 495 645 44 56 Contact information www smartlabs tv support smartlabs tv Assembling factory Sichuan Changhong Network Technologies
13. ing to control with the Remote Control To connect the RF Remote Control do the following 1 Insert the batteries into the Remote Control 2 Putthe Remote Control close to the IPTV STB no farther than at 20 cm from the device Press the Favorites and buttons simultaneously If the Remote Control s led indicator lights up and lights permanently the Remote Control has been successfully connected to the IPTV STB and the RF Remote Control is ready to use If the indicator blinks repeat steps 2 3 4 If the indicator does not light up make sure that you have installed the working batteries properly and repeat steps 2 3 4 14 Connecting External IR Receiver for Remote Control If your device is supplied with the RF Remote Control you do not need an exter nal IR receiver If your device has a slot to plug in an external IR receiver you can connect it to IPTV STB and use this receiver in the direct visibility range instead of using internal IR receiver of the device Both external and internal receivers accept signals from the same Remote Control When an external receiver is connected it accepts signals from Remote Control In order to send commands to the internal receiver aiming the Remote Control to the window on the front panel of the device disconnect the external receiver from IPTV STB External IR receiver is not included with the accessories You can purchase it separately Insert the external IR receiver i
14. ngs in the device defined by the manufacturer 5 RESET Front Panel 11 Green IPTV STB is switched on and works normally 1 Power indicator Red IPTV STB is in the stand by mode The internal IR receiver s window accepting signals from the IR remote control RC This window should be in the direct visibility 2 IR receiver s window range from the IR RC if an external IR re ceiver is not used If the device is supplied with the RF RC it has no internal IR receiver Bottom Panel 1 SATA HDD slot Internal HDD connection slot 2 HDD cover 12 Starting the IPTV STB When you switch on IPTV STB for the first time the device will start down loading the latest version of software During the update the special service message and progress bar are displayed on the TV set s screen The soft ware update process can take a few minutes Do not disconnect the device from power supply and Ethernet before the update is complete After finish ing the update procedure IPTV STB will automatically reboot As a new software version appears it will be automatically downloaded to the device Using the Remote Control Differences Between RF and IR Remote Controls Your IPTV STB can be supplied with IR or RF remote control RC Determine the Remote Control type by the picture see Remote Control But tons Specification IR Remote Control is a common remote control which requires an IR receiver located in th
15. nto the slot located at the back panel of the de vice see the back panel picture Place the signal receiving eye of the receiver in the direct visibility range from the device see Device Installation 15 Remote Control Buttons Specification A 10 smartlabs RF Remote Control smartlabs IR Remote Control NO 16 Q Turn on stand by 7f Mute Numeric buttons Last ch Last channel Switches the IPTV STB on or turns the device into the stand by mode Disables Enables sound Enter numbers letters symbols At the time of watching TV channels switches the translation to the previous viewed channel At the time of watching a move rewinds for a few seconds back 10 11 12 ils 14 15 16 17 18 Search Home TV VoD Menu V A 4b Arrow buttons OK VOL A V Volume CH A V Channels Colored buttons Video player buttons Jr Favorites 9 q Info e Settings A Profile Opens the search window Returns to the main menu from any posi tion Opens the TV channels menu Opens the video on demand menu Opens the menu Move through menu items select and confirm options Change volume Switch channels The button functions are determined by the service provider Play Bg Stop ll Pause PP Fast forward 44 Rewind Next frame Previous frame Opens the favorites menu Opens the information menu Opens
16. ternal HDD SML 292 HD premium only e USB flash drive USB Flash or other USB device web camera external HDD e External IR receiver y Note If your device is provided with the RF remote control it has no slot to plug in an external IR remote control Attention Before using the RF remote control you should connect it to the IPTV STB as it is described in the Connecting the RF Remote Control sec tion Indicators and Slots Back Panel 10 LAN S PDIF USB HDMI Her s SML 272 SD R Audio L Video Y Pb Pr DC 12V Ethernet port 10 100 Mbit s for the connection to a network device the service provider s equipment or Internet router Optical audio output to audio receiver or speakers of the PCM or Dolby Digital 5 1 digital audio format It is possible to switch the output mode from the application s menu if your service provider provides this feature USB 2 0 port for the connection to external devices Audio video output of high definition for the connec tion to a TV set or AV receiver Stereo audio output R Right channel L Left channel Composite video output Component video output Power adapter slot Side Panel 0 2 0 0 9 1 USB USB 2 0 port for the connection to external devices 243 e Mini jack 3 5 mm slot for the microphone connection 4 Ext IR Optional hoes 3 5 mm slot for the external IR receiver con The button inside restores the default setti
17. y of the screen The IPTV STB manufacturer is not responsible for any harm caused by this reason IPTB STB can automatically update its software Do not switch off the device and disconnect it from Ethernet until the software update is com plete The IPTV STB manufacturer is not responsible for consequences of incorrect software update in your device Cleaning e Turn off the device before cleaning e Wipe the device with a clean dry rag only e Clean the ventilation holes in the device s enclosure regularly e To remove stains from the device s surface it is possible to use a slightly damp rag e Do not use chemical cleaner car polish dissolvent aerosol cleaning agents abrasive powders and materials for cleaning the device and acces sories Servicing 1 Do not open the device Unauthorized opening of the device deprives war ranty The manufacturer s label is located at the bottom side of the device Breach of the label removes warranty from the device 2 To repair the device contact your service provider Device Installation 1 Remove IPTV STB from packaging 2 Remove the protective film from the glance top panel of the device 3 Choose one of the following positions _ 0 Horizontal position on table holder shelf Remote IR receiver Vertical position on the wall 4 f your IPTV STB is equipped with an IR receiver you should place the device s front side towards the user
Download Pdf Manuals
Related Search