Coyote Stainless Steel Gas Grill
Contents
1. cee 4 Gas Requirements 0c00 7 Using Your Burners amp Grilling 13 Lighting Your Grill 008 16 Operation and Features 18 Care amp Maintenance 66 19 Troubleshooting Your Grill 24 Limited Warranty 00000 26 Parts LIStiNGS 0ceee sees 28 Safety Symbols e WARNING DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury e CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate personal injury or property damage e WARNING WARNING indicates a_ potentially hazardous situation which if not avoided could result in death or serious injury e WARNING IF YOU SMELL GAS 1 Shut off gas to the appliance 2 Extinguish any open flame 3 Open Lid 4 If odor continues keep away from the appliance and immediately call your gas supplier or your fire department e WARNING WARNING 1 DO NOT store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance 2 An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance e WARNING FOR OUTDOOR USE ONLY NEVER operate grill in enclosed areas as this could lead to gas accumulating from a leak causing an explosion or a carbon monoxide buildup which coul2. COYOT Coyote 2 Burner Grill Built in amp Free Standing Model CCX2LP CCX2NG CCX2LP FS CCX2NG FS Conforms to ANSI STD Z21 58a 2008 Certificated to CSA STD 1 6a 2008 Intertek 4006980 IMPORTANT Read the lighting instruction on Page 15 before first time use To installer or person assembling grill Leave this manual with grill for future reference To consumer Keep this manual for future reference COYOTE OUTDOOR LIVING INC www coyoteoutdoor com www goedekers com Welcome amp Congratulations Congratulations on your purchase of a new grill We are very proud of our product and we are completely committed to providing you with the best service possible Your satisfaction is our 1 priority Please read this manual carefully to understand all the instructions about how to install operate and maintain for optimum performance and longevity We know you ll enjoy your new grill and thank you for choosing our product We hope you consider us for future purchases Please read and save the instructions This Manual provides specific operating instructions for your model Use your grill only as instructed in this manual These instructions are not meant to cover every possible condition and situation that may occur Common sense and caution must be practiced when installing operating and maintaining any appliance www goedekers com Table of Contents Safety Instructions 2 Locating the Grill
3. Make sure all burner valves are in the OFF position 2 All NG units need to have a regulator and shut off valve on the supply line 3 All Pipe threads need to have proper gas rated outdoor rated thread sealant Flare ends do not need or utilize pipe sealant 4 Your NG Coyote grill comes with a 1 2 regulator a You need to seal the regulator to the hose using your pipe sealant b Then attach the flare end to your manifold line with no pipe sealant c Next attach your next connection hose not included to the other side of the NG regulator it is also 2 MIP I We suggest using 12 stainless steel corrugated hoses for all NG Grills ii Make sure that you purchase a hose of adequate length and capacity for the intended application d Connect the other end of this hose to your shut off valve I Depending on your choice of hose and shut off the nipple going into the shut off valve may vary e Test all connections for leaks with a soap and water solution High Elevation Installation and Use Coyote Grills are designed to operate most efficiently at 0 2000 feet above sea level From 2000 4000 feet above sea level you will not notice any substantial decrease in your heat although more gas is combusting within the burners due to less oxygen Above 4000 feet you may experience a little longer cooking time on your grill than you would experience at sea level But again this is just due to the air fuel mixture taking place within the b
4. top of the cart so that you can gain access to the cotter pins holding the burners in position If you choose to slide the grill forward be extremely careful that it does not slide all the way off of the cart and on to the floor Once you have access to the cotter pins 1st picture shown below remove them from the burners and then remove then carefully remove each burner by pulling up and away from the gas valve in front Use a wire brush on the outer surface of the burner to remove any food debris and or dirt Clean any clogged ports with a stiff wire such as an open paper clip Inspect the burner for damage cracks or holes and if such damage is found order and install a new burner After re installation check to insure that gas valve orifices are correctly placed inside the ends of burners and also check to make sure the position of the spark electrode is in its correct spot Grill head moved forward on cart with gas line Cotter pins holding burners in place Bolts to remove grill head from cart disconnected Stainless Steel Care and Maintenance It is a common misconception that stainless steel will maintain its original factory shine with little help from the consumer Unfortunately this is not true Stainless steel will not stain discolor corrode or rust as fast as other types of steel but it is not fully stain or weather proof If it is not properly maintained all grades of stainless steel can face surface discolo
5. aluminum foil from orifices and check orifices for obstruction Check electrode Reinstall flavorizers cooking grids and warming rack Reconnect to gas source and observe burner flame for correct operation IMPORTANT You should NOT line the bottom of the grill housing with aluminum foil sand or any other grease absorbent substance Grease will not be able to drip into the drip tray and a grease fire may occur oy oy DO NO w MAINTENANCE GUIDELINES 1 Keep outdoor cooking gas appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids 2 Do not obstruct the flow of combustion and ventilation air Keep the ventilation opening s of the cylinder enclosure free and clear from debris 4 Visually check burner flames Burner flames should be blue and stable with no yellow tips excessive noise or lifting If any of these conditions exist call our customer service line 5 Clean outdoor cooking gas appliance including special surfaces with recommended cleaning agents if necessary 6 Check and clean burner for insects and insect nests A clogged tube can lead to a fire beneath the grill Recommended Cleaners for Specific Situations CLEANING AGENTS COMMENTS Soap ammonia detergent Routine Cleaning P Medallion 9 Apply with cloth or sponge Fingerprints amp smears Arcal 20 Lac O Nu Ecoshine Provides barrier film Stubborn stains amp Cameo Talc Zud Rub in direct
6. leaks immediately Check only with a soap and water solution Never check for gas leaks with an open flame Notice We strongly recommend professional installation and hookup of the Gas BBQ grill These instructions will provide you with the measurements necessary for you or your builder to construct a masonry structure to house your outdoor gas grill IMPORTANT Gas fittings regulator and installer supplied shut off valves must be easily accessible LOCATION OF YOUR GRILL Locate the grill only in a well ventilated area Never locate the grill in a building garage breezeway shed or other such enclosed areas without an approved ventilation system During heavy use the grill will produce a lot of smoke Ensure there is adequate area for it to dissipate Ventilation Requirements for Proper Operation of your Coyote Grill e Ventilation for a gas grill is absolutely mandatory to ensure that your grill performs as intended and to ensure the safety of you and your family The vents that are required to honor a Coyote warranty not only ensure that any heat that is trapped inside your grill from environmental factors such as wind escape but they also allow any gas that has leaked from a tank or connection to escape before a buildup of such gas can occur and possibly ignite e Asimple way to think of what is occurring inside your grill is that when your burners are on they are emitting a flame that creates the heat to cook your food This heat
7. lid while igniting the barbecue s burners or not waiting 5 minutes to allow the gas to clear if the barbecue does not light may result in an explosive flame up which can cause serious bodily injury or death WARNING DO NOT use the grill if gas odor is present DO NOT stand with head body or arms over the grill when lighting Inspect the hose before using the grill If there is excessive abrasion or wear or if the hose is cut it must be replaced prior to the outdoor cooking gas appliance being put into operation The replacement hose assembly shall be that specified by the manufacturer Ensure the area around the barbecue is clear of flammable substances such as gasoline yard debris wood etc Ensure there is no blockage of the airflow through the vent space located below the face of the unit GENERAL RULES Do not leave the grill unattended while cooking Make sure the grill has been leak tested and is properly located Check the end of each burner tube is properly located over each valve orifice Light the grill burners using the instructions provided in this manual Adjust heat settings to your desired cooking temperature Allow grill to cool down wipe off any splatters or grease and clean the drip tray as needed Do not put a cover on the grill while it is still hot as it could start a fire wwillgede Geom Lighting Instructions Using the Ignition System 1 Open the canopy 2 Keep your body arms
8. listed overfilling prevention device Read labels on the L P Gas Supply Cylinder New cylinders are always shipped empty for safety Allow only qualified L P gas dealers to fill or repair your L P gas supply cylinder Inform the gas dealer if it is a new or used cylinder to be filled After filling have the gas dealer check for leaks and to see that the relief valve remains free to function Hose and Regulator Comes standard with the grill The Type 1 connection system has the following features The system will not allow gas to flow until a positive connection TER eA has been made NOTE The cylinder control valve must be turned off before any connection is made or removed The system has a thermal element that will shut off the flow of gas in the event of a fire The system has a flow limiting device which when activated will limit the flow of gas to 10 cubic feet per hour NEVER use grill without leak testing this connection LP Propane Gas Supply Connection 1 The tank valve should be in the OFF position If not turn the knob clockwise until it stops 2 Make sure all burner valves are in the OFF position 3 Always connect the gas supply regulator as follows Insert the regulator inlet into the tank valve and turn the coupling nut clockwise until the coupler tightens up see picture Do not over tighten the coupler Turn the main tank valve on and turn the burner control valves
9. not cover any failures or operating difficulties due to accidents abuse misuse alteration misapplication vandalism improper installation maintenance or service damages caused by flashback fire or grease fires as set out in the Owner s Manual This warranty wwitiqeedae Grea does not cover scratches dents corrosion or discoloration caused by weather heat abrasive and chemical cleaners pool or spa chemicals and or any tools used in the assembly or installation of this unit This warranty does not cover paint loss surface rust corrosion or stainless steel discoloration which is considered normal wear and tear This warranty does not cover the cost of any inconvenience personal injury or property damage due to improper use or product failure Deterioration or damage due to severe weather conditions such as hail hurricanes earthquakes tsunamis tornadoes terrorism discoloration due to exposure to chemicals either directly or in the atmosphere Acts of God forces of Nature are not covered by this limited warranty w Parts List Coyote CCX2 Cart a wwii Coyote CCX2 LP NG CCX2 LP amp NG Parts Listing Cart Grill Part Part Description Number Description Number 20 21 22 23 24 25 6 wwitlqeedab ican
10. on the unit to the HIGH position for about 20 seconds to allow the air in the system to purge before attempting to light the burners i Type 1 Connector z D7 sad ww E Pre Operation Leak Testing DANGER 3 Do not insert any tool into the valve outlet or safety relief valve You may damage the valve and cause a leak Leaking propane may result in explosion fire severe personal injury or death 3 Ifa leak is detected at any time or you cannot stop a gas leak immediately close pipeline valve and call LP gas supplier or you fire department 3 Check all gas supply fittings before each use and each time the gas supply cylinder is connected to the regulator Have a qualified service technician leak test the grill any time a part of the gas system is replaced WARNING Never attempt to attach this grill to the self contained LP gas system Do not use grill until leak testing Before Testing DO NOT smoke while leak testing Extinguish all open flames Never leak test with an open flame Mix a solution of equal parts mild detergent or liquid soap and water Leak Testing Valves Hose and Regulator m 1 Turn all grill control knobs to OFF 2 Be sure hose is tightly connected to LP tank 3 Completely open LP tank valve by turning cylinder valve knob counterclockwise right to left If you hear a rushing sound turn gas off immediately There is a major leak at the connection Correct bef
11. Always adhere to the specified clearances listed Do not leave the grill unattended while cooking Do not use natural gas in a unit designed for liquid propane gas or vice versa Do not use fuel such as charcoal briquettes in a gas grill Keep children and pets away from hot grill DO NOT allow children to use or play near the grill Never attempt to repair or replace any part of the grill yourself unless specifically recommended in this manual All other services should be performed by a qualified service technician 10 Never lean over an open grill Do not place clothing or other flammable material on or near the grill Do not wear loose fitting clothes or long sleeves while using the grill as some fabrics can be highly flammable 11 Have an ABC fire extinguisher accessible Never attempt to extinguish a grease fire with water or other liquids 12 Never use aluminum foil to line the grill racks or the drip trays this can alter airflow for proper combustion and also build up heat in the control area causing the knobs and igniter to melt 13 When using the grill do not touch the grill rack burner grate or immediate surroundings as these areas become extremely hot and can cause burns Always use a covered hand when opening the grill hood and only do so slowly to allow heat and steam to escape 14 DO NOT allow grease or other hot material dripping from the grill onto the valve hose or regulator turn off gas supply immediately After the g
12. alize that this is the hottest portion of your grill for several reasons o First the grills hood and rear panel does not have the same amount of fresh air moving across the rear of the cooking grate as the front of the cooking grate does Every time you open the hood the front will cool while the back retains the majority of the heat Underneath where the burner is attached to the back of the body you will see that there is a crossover in between each burner This crossover sends gas from one burner to the next as long as the valves are open to ensure that all of your burners will light in case your igniters fail For example if you can only get one burner to light you just need to keep the hood open and turn on the valve next to it to the high position Gas will then travel through the new open burner and will catch the flame from the initial burner Burner Use Indirect and Direct As you can imagine by controlling how much gas flows through your burner determines the size of your flame The ideal flame will be blue with no yellow tip or excessive noise coming out of the burner If you happen to have any of these problems e You will want to check the air adjustment screw on the side of the burner itself called the Air Venturi and also the adjustment screw that resides directly below the orifice to ensure proper gas flow into the burner from the valve W e a e eam e There are many reasons that can cause poo
13. and face as far away from the burners and cooking surface as possible 3 Depress and rotate the knob counter clockwise to the High position a As you are nearing the High position you will notice the valve getting tougher to turn This is the spring inside the valve building up energy to create the spark Once you hear a click the igniter has fired the spark and you must turn the valve completely off to generate another spark b Do not turn the knob too fast as you need the gas to travel into your manifold then to your valve and finally into the burner where it will meet the spark from the igniter at the front of the burner Alternatively if you turn it too slow you can cause a build up of gas in the grill and create a large flash when it ignites 4 Ifthe burner does not catch on the first attempt try again immediately but be very aware of any gas building up inside the grill If the grill does light after three attempts turn the valves to the Off position and allow the grill to clear of any built up gas for 5 minutes 5 If at this point the grill will still not ignite you can try the manual lighting process below with a long stem lighter and you can also contact Coyote Customer Service for further assistance to troubleshoot your grill 6 To turn the grill Off you simply turn each knob clockwise until it can not turn anymore It is also normal to experience a popping noise when the burners are turned off abruptly Manually Li
14. connecting grill to gas source make sure BBQ Grill control knobs are in the OFF position e Verify the type of gas supply to be used either natural or LP and make sure the marking on the appliance rating label agrees with that of the supply e All pipe sealants must be an approved type and resistant to the actions of LP gas Never use pipe sealant on flare fittings e The installation of this appliance must conform with local codes or in the absence of local codes with either National Fuel Gas Code ANSI Z223 1 NFPA 54 Natural Gas and Propane Installation Code CSA B149 1 or Propane Storage and Handling Code B149 2 or the Standard for Recreational Vehicles ANSI A 119 2 NFPA 1192M and CSA Z240 RV Series Recreational Vehicle Code as applicable WARNING Gas valves are preset at the factory to operate on LP or natural gas If you wish to convert be sure to contact your grill dealer FIRST LP Gas Hook up This propane gas grill is designed to operate on propane gas ONLY at a pressure regulated at 11 279 4mm water column W C when equipped with the correct propane orifices on the valves and a propane regulator on the supply line regulated at the residential meter The LP gas grill is designed to be used with a standard 20 Ibs gas cylinder and must be constructed and marked in accordance with specifications of the US Department of Transportation for propane gas cylinders Always keep cylinder securely fastened in an upri
15. cover normal wear of parts damage resulting from any of the following negligent use or misuse of the product use on improper fuel gas supply use contrary to operating instructions or alteration by any person other than a factory service center The warranty period is not extended by such repair or replacement WARRANTY CLAIM PROCEDURE If you require service or parts for your Coyote Grill please contact our Warranty Service Center for factory direct assistance Our hours of operation are 8 am to 4 pm CST The phone number is 855 520 1559 and the Fax number is 214 520 1450 You may also fill out warranty claims online at www coyoteoutdoor com Please have your model number serial number and proof of purchase available for any warranty claim Coyote Outdoor may require the return of defective parts for examination before issuing replacement parts If you are required to return defective parts shipping charges must be prepaid by the customer Upon examination and to Coyote Outdoor s determination if the original part is proven defective Coyote Outdoor may approve your claim and elect to replace such parts without charge In any instance customer is responsible for shipping and handling of the replacement parts Product repair as provided under this warranty is your exclusive remedy Coyote Outdoor shall not be liable for any incidental or consequential damages for breach of any express or implied warranty on its products This warranty does
16. d result in injury or death DO NOT use your grill in garages breezeways sheds or any enclosed area NOT FOR USE BY CHILDREN If these instructions are ignored a hazardous fire or explosion could result in physical injury death or property damage Safety Instructions WARNING Improper installation adjustment alteration service or maintenance can cause injury or property damage Read the installation operating and maintenance instructions thoroughly before installing or servicing this equipment General Safety Instructions 1 For Household Outdoor Use Only DO NOT use indoors or in any type of enclosed area such as a garage shed or breezeway Keep clear of trees and shrubs The grills are not intended for installation in or on recreational vehicles portable trailers boats or any other moving installation Not for commercial use 2 The area surrounding your new grill should be kept clean and free from flammable liquids and other combustible materials such as mops rags or brooms as well as solvents cleaning fluids and gasoline 3 To reduce the risk of serious or fatal injury from breathing toxic fumes and from explosion and fire as a result of leaking gas use only outdoors in an open area with good ventilation Do not obstruct the flow of combustion and ventilation air 4 Never use the grill in windy conditions If located in a consistently windy area oceanfront mountaintop etc a wind break will be required
17. d to purchase a stainless steel scratch kit These kits are popular in retail stores but can be easier to obtain online A very popular one is called Scratch B Gone With these kits you will not polish the unit until you are done re scratching the entire product you are working on With a scratch kit the goal is to literally re scratch the entire surface so that the original grains are replaced by your new scratched in grains With this practice you must be willing to do the entire surface as you will notice a start and stop point Also be careful to pay attention to your rolled or finished edges as these scratch kits will ruin this finish After you have used the kit you will want to follow it up with a good stainless polish as mentioned prior and then a dry towel for a final wipe down ANNUAL CLEANING OF GRILL HOUSING Burn off the barbecue after every cookout will keep it ready for instant use however once a year you should give the entire grill a thorough cleaning to keep it in top operating condition 1 Shut off gas supply at source and disconnects fuel line Protect fuel line fitting Remove and clean the cooking grids flavorizers and burners Remove warming rack and wash with mild detergent and warm water Cover the gas valve orifices with a piece of aluminum foil Brush the inside and bottom of the grill with a stiff wire brush and wash down with a mild soap and warm water solution Wash thoroughly and let dry Remove
18. fore being cleaned beach owners must be diligent in maintaining their outdoor stainless equipment w 5 Dust or rust from other metals found it ways onto the grill and was left on for an extended period of time 6 Organic matters such as certain types of food might have gotten onto the surface of the grill and it was then covered With high humidity and low oxygen corrosion will start to take place 7 Sprays and cleaning solutions containing alkaline lime acid salt might have been left on the grill surface un dried 8 No stainless steel polish was ever used after one of the above mentioned acts took place Ways to Avoid Rust on your Grill 1 Always purchase a Coyote Grill cover for your unit This will ensure that your cover is correct fit and breathable while providing the protection needed to keep all other contaminants off of the surface 2 When installing the unit make sure to keep the unit covered when any masonry work is being performed If any mortar or dust does come into contact with the stainless make sure to wipe it off as soon as possible and use a stainless steel polish immediately afterwards 3 Position your grill away from areas that can receive water splash from a pool or hot tub 4 Do not store pool chemicals in your island or island cabinets How to Remove Scratches from your Stainless Steel If your situation is a little more serious and you have obtained scratches in your equipment then you will nee
19. ght position Never connect an unregulated propane gas cylinder to the grill Do not subject propane cylinders to excessive heat CAUTION Never store a LP gas cylinder inside a building or in the vicinity of any gas burning appliance Cylinder Specifications Any L P gas supply cylinder used with this grill must be approximately 12 inches diameter and 18 inches high The maximum fuel capacity is 80 and is approximately 20 pounds of propane w ___f Shutoff The L P cylinder must have a shut off valve see picture terminating ea Valve ina Type 1 L P lt Zollar A Type 1 compatible cylinder with a Type 1 cylinder valve has a WN 5 back check valve which does not permit gas flow until a positive seal has been obtained The cylinder must be arranged for vapor withdrawal It must also include a collar to protect the cylinder valve A safety relief device having direct communication with the vapor space of cylinder must be Na provided This will expel high pressure gas if the cylinder is overfilled pi or overheated which could result in fire or explosion All L P gas cylinders used with this appliance shall be constructed and marked in accordance with the specifications for L P gas cylinders of the U S Department of Transportation DOT or the National Standard of Canada CAN CSA B339 Cylinders Spheres and Tubes for Transportation of Dangerous Goods and Commission as applicable and shall be provided with a
20. ghting the Burners e If for some reason igniters fail to light burners can be lit with a gas lighter o To light gas grill with a gas lighter make sure the grill has been leak tested and burners can be properly located Remove the cooking grids and flavorizers from the burner you wish to light Insert long necked gas lighter placing it near the burner ports Press in the far right control Knob and rotate left to HIGH setting to release gas Turn on the button on gas lighter burner should light immediately Place back the cooking grids and flavorizers Adjust burners to desired cooking temperature wa a Operations and Features When you first ignite your grill burn the grill to get rid of any odors or debris that may be left over from manufacturing and transit This is done by operating your grill at the HIGH setting with the hood closed for no more than 5 minutes e Since this is a high temperature grill closing the hood will cause heat to build up and could easily cause an excessive flare up that could cause internal damage to the grill knobs igniter etc e After you have burned off the grill you are ready for cooking Preparing Food for the Grill WARNING Always observe safe food handling and safe food preparation practices when using this Grill to prevent food borne illnesses Always cook foods adequately Undercooked foods can retain bacteria especially if thawed or exposed to warm conditions
21. i f bolish Ii discoloration First Impression A E a Any good commercial Grease amp Oil detergent Apply with sponge or cloth Restoration Passivation Barkeepers Friend Super Sheen a E con Troubleshooting Your Grill GENERAL TROUBLE SHOOTING You should inspect the burners at least once a year or immediately if any of the following conditions occur e The smell of gas e Flames appearing mostly yellow Some yellow at the tips is OK e The grill will not get hot enough e Burners make a snapping noise e The grill heats unevenly SPIDER AND INSECT WARNING INSECT WARNING Spiders and insects can nest in the burners of this and other grills which could disrupt gas flow This dangerous condition could cause a fire behind and beneath the valve panel damaging the grill and making it unsafe to operate We recommend you check the grill and remove any spiders insects and webs at least once a vear to reduce this risk WHEN TO LOOK FOR SPIDERS You should inspect the burners once a year or immediately after any of the following conditions occur 1 The smell of gas in conjunction with the burner flames appearing yellow 2 The grill does not reach temperature 3 The grill heats unevenly 4 The burners make popping noises BEFORE CALLING FOR SERVICE If the grill does not function properly use the chart below before contacting your dealer for service You may save yourself the cost of a service call Troubleshoot
22. ing is for general purposes only If the problem still exists contact your dealer or the nearest authorized agency for service Possible Causes and Solutions Grill will not light when the Is your gas supply turned on igniter button is pushed If this is an L P grill is there gas in your tank Check your gas level Is one of your burners turned on Allow up to 5 seconds of gas flow to ignite Is your igniter working If you hear a snapping sound can you see a spark at the electrodes Note You will need to remove your cooking grates and flavorizers to see the electrodes The electrodes should ww have a 1 8 to 4 gap between the electrode and contact point Check for a loose wire connection at the electrode box Check to see if debris is blocking the electrodes If the igniter is not working can you light the grill with a lighter Check flavorizers and cooking grates for excess food or grease build up Ensure grill is not placed directly in the path of wind Be sure drip tray is clean Note Some flare ups may be inevitable if cooking greasy foods Yellow Flames Check the burner inlet for obstructions particularly at air inlets for each burner Grill may be in an area that is too windy Flame blows out on low setting Check for spider webs or insect nest in venturi and clean or has uneven heat distribution venturi l l A cold grill needs to be preheated for 5 minutes on high setting Venturi may be m
23. isaligned and needs to be lined up over orifices Windy weather will require you to move grill away from the wind Lack of fuel Check to see cylinder valve is open and cylinder has fuel Low heat with the knob on Check to see if the fuel hose is bent or kinked HIGH Make sure the grill area is clear of dust Check your gas supply and gas pressure If it is only one burner that appears low make sure the orifice or burner is clean Grill is Too Hot Excess grease build up causing grease fires Damaged or faulty regulator Replace with factory authorized parts Cook on a lower temperature setting Flame behind control panel or IMMEDIATELY shut off cylinder valve and allow grill to cool control knob area Check for spider webs or insect nest in venturi and clean venturi Gas is leaking from a faulty connection Tighten connections with an adjustable wrench and replace damaged parts Perform a leak test on all connections before cooking on grill again Venturi may be misaligned and needs to be lined up over orifice Fire at any connection IMMEDIATELY shut off cylinder valve and allow grill to cool e Gas is leaking from a faulty connection Tighten connections with an adjustable wrench and replace damaged parts Perform a leak test on all connections before cooking on grill again w D Limited Warranty LIMITED WARRANTY Coyote Outdoor warrants to the original purchaser at the original site of delivery with proof of pu
24. must exhaust from the grill otherwise you would eventually have a unit that would not only build up immense heat but also immense pressure This could cause severe damage to not only the grill but any operators or property near by With that said if you have wind coming into the back of your unit the problem will not be with the wind hitting your flames and causing them to push the flame downward The problem actually lies with the wind acting as a block for the exhaust which is mainly out the back of the hood above the rear panel but below the top of the hood This blockage of exhaust is what starts the problems e If the island is ventilated properly with a minimum of 2 vents for cross ventilation and at least 20 sq in on each vent then any heat that is trapped inside due to wind should be able to dissipate out of the island vents However if the island is not ventilated properly and the wind is coming from the back then the heat will try to escape through the easiest exit which will most likely be through the bottom of the grill and front control panel This can cause the control panel and knobs to get hot to the touch and possibly even burn your fingers not to mention that it can melt all rubber gaskets on the valves and damage the ignition system to where it will need full replacement PA allaca e Ventilation and the variable of your most common wind direction must always be considered when planning your outdoor cooking island Just the
25. of the grill so that the motor and rotisserie spit handle will have room on the counter as these extend past the overall dimensions of the grill body e CLEARANCE TO COMBUSTIBLE CONSTRUCTION For combustible construction you must have at least 24 clearance to any combustible material in any direction for a Coyote Warranty to be upheld and for the safety of the homeowner You can NOT locate the grill under any combustible material without an approved ventilation system directly located above the unit e INSULATED JACKETS AND COMBUSTIBLE CONSTRUCTION If you must use combustible material to build your grill island AND you are going to be within 24 of the grill with this combustible material then you must use the appropriate Coyote Insulated Jacket The insulated jacket will act as a barrier to protect your grill island from the heat and fire of your Coyote grill If an insulated jacket is not used in a combustible material island the warranty on the Coyote grill will be voided immediately and safety can not be ensured For Built in Installations A built in grill is designed for easy installation into masonry enclosures For non combustible applications the grill drops into the opening as shown in cut out detail drawing Fig A and hangs from the grill body itself A bottom deck is not required to support the grill from the bottom It is also required that e Two ventilation holes of at least 20 sq inches in size must be present to help relea
26. on when not in use 27 Use only a Ground Fault Interrupter GFI protected circuit with this outdoor cooking gas appliance CALIFORNIA PROPOSITION 65 WARNING The burning of gas cooking fuels generates some byproducts which are on the list of substances which are known by the State of California to cause cancer or reproductive harm California law requires businesses to warn customers of potential exposure to such substances To minimize exposure to these substances always operate this unit according to the Use and Care Manual ensuring you provide good ventilation when cooking with gas wwitlgoedelaestcon Locating the Grill Check your local building codes for the proper method of installation In the absence of local codes this unit should be installed in accordance with the National Fuel Gas Code No Z223 1 1998 USA or CAN CGA B149 1 2 Natural Gas Propane Code Canada latest edition or the National Electrical Code ANSI NFPA No 70 or the Canadian Electrical Code CSA C22 1 1990 or latest version Before installing built in grills in enclosures copy all product information such as model number serial number and type of grill e g natural gas or LP and store information in a safe place Ifthe grill is installed by a professional installer or technician be sure that he shows you where your gas supply shut off is located All gas lines must have a shut off that is readily and easily accessible If you smell gas check for gas
27. operly That is the Coyote way o Coyote does not supply any gas fittings or lines other than the regulator needed within the grill box o All Coyote LP Grills come with a 20lb tank regulator This regulator can not be used or modified to work on any other setup If you are running off of a large capacity tank more than 20lbs then an in line LP regulator is needed Coyote Customer Service must be contacted to assist with this situation o As counties vary from state to state it is upon the owner installer to ensure that all county state and federal codes are followed for any gas installation wa Natural Gas Hook up Always check the rating plate to make sure the gas supply you are hooking up to is the gas type the grill is manufactured for This natural gas grill is designed to operate on natural gas ONLY at a pressure regulated at 4 101 6mm water column W C when equipped with the correct natural gas orifices on the valves and a natural gas regulator on the supply line regulated at the residential meter IMPORTANT Never connect the grill to an unregulated gas supply Natural gas connections must be performed by a licensed contractor or local gas company representative Natural Gas Hose and Regulator IMPORTANT NEVER use grill without leak testing this connection Natural gas regulator model GR120 Gas pressure 4 101 6mm Maximum rate working pressure 1 2 Psig Natural Gas Supply and Connection 1
28. ore proceeding by calling franchiser for replacement parts 4 Brush soapy solution onto areas where bubbles are shown in LP tank see picture bubble 5 If growing bubbles appear there is a leak Close LP tank valve immediately and retighten connections If leads cannot be stopped do not try to repair Call franchiser for replacement 6 Always close LP tank valve after performing leak test by turning cylinder valve knob clockwise NOTE When leak testing this appliance make sure to test and tighten all loose connections including the side burner A slight leak in the system can result in a low flame or a hazardous condition LP Gas Supply Cylinder Disconnection 1 Turn the burner valves off 2 Turn the tank valve off Turn clockwise to stop 3 Detach the regulator assembly from the tank valve by turning the quick coupling nut counterclockwise a LP Tank Removal Transport and Storage Turn OFF all control knobs and LP tank valve Turn coupling nut counterclockwise by hand only do not use tools to disconnect Lift LP tank wire upward off of LP tank collar then lift LP tank up and off of support bracket Install safety cap onto LP tank valve Always use cap and strap supplied with valve Failure to use safety cap as directed may result in serious personal injury and or property damage A disconnected LP tank in storage or being transported must AT TT have a safety cap installed l as shown Do not store an LP
29. prior to cooking Always use separate plates and utensils for the handling of raw food Never place raw food and cooked food on the same plate and never place cooked food on a plate that was used for handling raw food Always carefully wash all plates and utensils used to handle raw food before using them to handle cooked food Always wash all vegetables seafood and poultry before cooking Always leave uncooked foods in the refrigerator until you are ready to start cooking Always marinate meat in the refrigerator Dispose of the excess marinade and never reuse it Grilling Tips If you pre cook meat or poultry do so immediately before grilling Refrigerate leftovers within 2 hours of taking food off the grill Never let the tray boil dry That could be hazardous as grease from fatty foods that have collected in the tray could ignite and possibly cause bodily injury or property damage Use a meat thermometer to be sure food has reached a safe internal temperature Always trim excess fat from your foods to reduce the occurrence of flare ups during cooking Apply a light coating of cooking oil to the cooking grids before grilling to prevent foods from Sticking Cook similar portion sizes together so that they all cook evenly Use tongs to turn foods on the grill Never pierce foods while they are cooking on the Grill as this will dry them out Turn foods infrequently Some chefs say that a good steak
30. r Instant Rust Out to remove the spots a Each of these polishing agents take about 30 seconds to work and then you simply wipe off the product if needed use a soft Scotch Brite pad to remove any tough spots If you used Barkeepers Friend then you do not need to do anything further If you used Instant Rust Out or another cleaning agent you would want to wipe it down with fresh water and dry it off again with a clean towel and then coat the steel with a layer of WD 40 or another Stainless Polishing solution which will act as a surface protectant for the steel i IMPORTANT Be sure not to have your grill on when using any flammable product such as WD 40 These products are extremely flammable in their aerosol form Environmental Factors that can affect your Grill Mother Nature is a wonderful thing but unfortunately she can be tough on outdoor appliances There are several usual causes for surface discoloration and corrosion on your stainless steel outdoor equipment 1 Mortar which contains lime from the island assembly process has rested on the unit for a pro longed period of time and the unit was not cleaned quickly 2 Pool chemicals were splashed onto the grill chlorine and acid will cause very quick problems and the unit was not cleaned off quickly 3 Hard water from sprinklers chlorine in the water was allowed to sit on the unit 4 Salt from the ocean air water was allowed to rest upon the grill for a prolonged period of time be
31. r flames and heat but none are more serious than a gas leak so always pay attention for the odor of gas NG or LP but do not also forget to clean your burners For Direct Cooking you simply cook your food over a direct flame that is hot and quick to cook but is also the quickest way to burn your food Pay attention closely if you choose this method Indirect Cooking however is used for larger cuts of meats and anything that you are intending to keep nice and juicy e All you need to do is turn off the burner that lies under the food being cooked and adjust the exterior burners flame so that you create a slow constant and even cooking environment for your food Sii i i fi N Hit tu Mh uh Instruction for Connecting the Transformer 1 CCX2LP NG Built In Transformer for Interior Lights Your transformer will connect on the left side of your grill looking at it from the front and operates the lights inside your grill Follow the pictures and insert the white male plug into the white female socket on the left side of your grill and then plug the 3 prong cord into a standard 110v outlet d 4 Male Plug Female Socket 2 CCX2LP NG FS Free Standing Transformer for Interior Lights For the free standing cart model CCX2 that comes fully assembled in the box the transformer plug shown above for built in application will already be attached to the grill All you need to do is to un package the transformer protected by a s
32. ration corrosion and eventually rust Any stainless Steel that is exposed to the environment will require attention and care throughout its life to ensure that it keeps its shine and structural integrity Cleaning the Stainless Steel and Polishing 1 To clean the stainless steel you will want to wash off all dirt and debris from the steel with warm water If you have tough spots to clean then a degreaser such as Formula 409 can be used Next you will want to rinse and dry the steel thoroughly with a clean towel Do not allow the steel to air dry as the standing water can cause surface discoloration The last thing you want to do is to protect to the unit with a good polish There are several polishes on the market that work great Barkeepers Friend Polish and Stainless Steel Magic are a few and will help keep your grill protected from the elements for a longer period of time Most of these polishes are toxic so you would only want to use these on the exterior of the grill not your cooking grates or flavorizers a You will want to apply the polish to a clean paper towel and wipe with the direction of the grain in the stainless steel b There should be no excess liquid on the surface but it is acceptable for it to be a little oily as that will dissipate If you have a situation where your grill has developed surface discoloration or surface rust then you need to clean the unit as stated above and use a good polish Barkeepers Friend Polish o
33. rchase of each Outdoor Gas grill Side burner that when subject to normal residential use it is free from defects in workmanship and materials for the periods specified below This warranty excludes grills used in rental and commercial applications This warranty excludes surface corrosion scratches and discoloration which may occur during regular use It does NOT cover labor or labor related charges There will be shipping and handling charge for the delivery of the warranty part s COMPONENT WARRANTY PERIOD Cooking Grids no rust or burn through ccee eee eeeeeseeeeesssseeesessssssessssssseeeeeeed YEars limited Flavorizer Bars no rust or burn through ccesceeeeeeeeeeeeeeeeeeeseseeeesseeessaaees 2 years limited Electric Plastic Component cccccecceceeeeeeseeeeeesage cess MEQ moanne eaa aeaaaee 2 years limited Ignition SySteMS VAIVES cccccce eee eee eens c eee A Bie nce Perec cccenccessenees 1 year limited Stainless steel fraMe NOUSING c cece cece cece cece eee eee ee ees seat eat eat eae esnaaaeeeeees Limited Lifetime Stainless Steel Burners no rust or burn through 0seeseeesssssseeeeessseeeeeeeeee Limited Lifetime Our obligation under this warranty is limited to repair or replacement at our option of the product during the warranty period The extent of any liability of Coyote under this warranty is limited to repair or replacement This warranty does not
34. rill has cooled determine the cause and correct it After cleaning the valve hose and regulator perform a leak test before continuing use 15 Do not heat any unopened glass or metal container of food on the grill Pressure may build up and cause the container to burst possibly resulting in serious personal injury or damage to the grill 16 Keep any electrical supply cords away from water or heated surfaces Electrical cords should be placed away from walkways to avoid tripping hazard ONDU wn 17 Keep gas supply lines as short as possible 18 Never move the grill when hot 19 DO NOT use while under the influence of drugs or alcohol 20 DO NOT store a spare gas cylinder under or near your grill 21 DO NOT grill without the drip tray in place hot grease could leak downward and produce a fire or an explosion Drip tray should be pushed all the way to the rack located just under the grill 22 Grease is extremely flammable Let hot grease cool down before attempting to handle or dispose of it The drip tray should be cleaned and free of grease on a regular basis 23 In the event that a burner goes out turn burner knobs to the full OFF position fully open the grill hood and let it air out Do not attempt to use the grill until the gas has had time to dissipate 24 Do not use grill until leak check has been made 25 Turn off the cylinder valve when your grill is not in use 26 Ensure the control knobs are in the OFF positi
35. rizers and cooking grates M a A Using Your Burners and Grilling Safely Your grill is designed to reach a temperature that you set by adjusting a valve that in turns adjusts the amount of gas that goes through each burner This Valve is located behind your knob and is the key to your heat and fuel consumption An example being Cooking on low will give you longer use out of a 20lb LP tank than will cooking on high every single time Furthermore the way to ignite the burners is through the valves so please understand the importance of this piece and the position care taken to the knobs e Example If you forget to turn a knob off and the burner is not lit then you will have a gas leak out of that valve You must be aware of your grills status and be responsible Burner Configuration and Heat Dispersion If you look under the very front of your cooking grates you will realize that for the first few inches the burner does not release any gas This is designed to be the medium heat portion of your grill for several reasons e One being that the flavorizers ensure even heat dispersion laterally across your grills cooking surface so the front is designed to be your medium heat section while you can utilize the middle of your cooking grates to get a good high heat do not forget that this all depends on how high you have your valves turned as well e As you move towards the back of your grill and past the middle section you will re
36. s threading will occur install the new orifices After you have started them with your fingers use the 6mm nut driver again and tighten the new orifices into each valve a Incase you confuse the orifices during the install LP orifices have a smaller hole than NG orifices due to propane coming out of the LP tank at a much higher pressure than natural gas Next you will need to remove your existing manifold fitting that connects to the regulator a LP grills come with a 3 8 male flare fitting coming out of the manifold pipe b NG grills come with a 1 2 male pipe fitting that comes out of the manifold pipe i Each of these fittings is designed to go straight into the appropriate regulator from the manifold Locate the new manifold fitting from your conversion kit and apply pipe thread sealant on the pipe fitting side of the nipple the side of the nipple that goes into the grills manifold pipe and tighten into the pipe Installing the new regulator a If converting to natural gas you will also want to apply pipe thread sealant to both sides of the regulator as these both sides are a 1 2 female pipe non flared fitting b If converting to propane the fitting at the end of the LP regulator is a 3 8 female flared fitting so no pipe sealant is necessary Once these steps have been completed you will want to perform a leak test stated previously in the manual at all new connections before cooking on the unit Replace the burners flavo
37. same as you would plan the layout and measure your indoor kitchen you must also do the same for the outdoors but you can not forget about Mother Nature and the effects she can have on your outdoor cooking equipment o Coyote Wind Guards If you do run into a situation where you will have wind coming into the back of the unit Coyote does sell Wind Guards that helo keep your grilll from overheating due to no exhaust occuring out the back of the grill Our Wind Guards should never be considered as a guaranteed solution to this problem They are only intended to help the wind divert up and over the top of the grill If the wind is strong then you can still have problems with the heat being trapped in the hood Our Wind Guards can be purchased through any of our authorized dealers Clearance e TO NON COMBUSTIBLE CONSTRUCTION For non combustible material Coyote grills can be placed directly on or adjacent to the non combustible material The hood on a Coyote grill pivots mainly on the body If you have a wall or partition behind the unit that would block ventilation then a minimum of 7 clearance from the back of the grill to the wall is needed for the purpose of ventilation If you do not have a wall or partition blocking the ventilation of the unit then you only need an extra 2 behind the unit for the hood to open fully If you wish to use the rotisserie option you will want to make sure that you leave adequate space at least 6 on each side
38. se any gas from a leak As Propane is heavier than air locate your vents at the tank valve height or lower e The counter should be flat and level in reference to the floor LP TANK STORAGE MUST BE ISOLATED IN A SEPARATE COMPARTMENT FROM THAT OF THE GRILL AND IT MUST BE VENTED AS WELL RECOMMEND BOTTOM VENTS FOR LP waad D Cut out Dimensions Figure A Width an l Depth 3 Gas Line Connection Electrical Connection for _ Light Transformer Qty 1 is More island vents The purpose of 2 vents is for cross ventilation If you have one on the other side then you only neec one on the alternate side Oty 2 on each just ensures no problems with airflow S Height Ventilation Vents _ Minimum of 2 per island At least 20 sq in per vent Electrical Product l l l Total BTU Cutout Dimensions Overall Dimensions f Outlets Description Ratings Needed 110V Heigmt wictn Depth Height width Depth LP NG Canopy Lights Each burner generates 20 000 BTU s Total for grill is 40 000 Canopy Lights have a transformer that mounts inside the cart or an island and provides power to the lights wongcedeBs con Gas Requirements NOTE Always have a qualified service technician perform difficult conversions or modifications WARNING Never attach an unregulated gas line to the appliance Connection to an unregulated gas line can cause excessive heat or fire IMPORTANT Before
39. should never be turned more than once Apply sugar based sauces such as commercial barbecue sauces only during the latter stages of cooking to prevent charring Soak the string you use to tie up roasts and poultry on the rotisserie spit to protect it from burning Use a disposable aluminum tray filled with water fruit juice wine or a marinade to add extra flavor and moisture to slow cooked foods like roasts whole chickens turkeys or ducks Controlling Flare ups Flare ups are a part of cooking meats on a gas grill This adds to the unique flavor of cooking on a gas grill Excessive flare ups resulting from the build up of grease in the bottom of the grill can over cook the food and cause a dangerous situation for you and your grill If this should occur DO NOT pour water onto the flames which can cause the grease to splatter and could result in serious burns or bodily harm If grease fire occurs close the hood and turn off the main burners until the grease burns m com out Use caution when opening the hood as sudden flare ups may occur To Minimize Flare ups Trim excess fat from meats prior to cooking Cook meats with high fat contents chicken or pork on Low settings or indirectly Ensure that your grill is on level ground and the grease is allowed to evacuate the grill through the drain hole Care amp Maintenance CAUTION All cleaning and maintenance should be done only when grill is cool amp with the fuel s
40. tainless steel box and attach it to the side of the cart as shown Once it is attached you will then need to connect the male plug coming out of the grill to the female socket that is sticking out of the transformer stainless steel box and then plug the 3 prong cord into a standard 110v outlet WARNING These two transformer should be kept away from the heat of the BBQ Keep any electrical supply cords and the fuel supply hose away from any heated surfaces HOW TO CHANGE THE LIGHT BULBS 2 S Remove the screw holding the bulb lens and light assembly to the frame Pull out the entire light assembly from the frame Loosen the screws that are holding the wires in the light assembly Once loosened reach into the light assembly using your fingers only grip the two outside edges of the light bulb but do not grip the top or bottom of the bulb as it might break Pull the bulb straight out so that the two electrode wires are completely removed with the bulb Place the used bulb in the trash When installing the new halogen bulb be sure to use a clean cloth or paper towel to ensure the longevity of the bulb Insert the new bulb using your clean cloth and genily snap it into position Re tighten the screws that hold the wires in place Re install the entire light assembly with the lens cover in place and tighten the screw to the frame Flip the switch on to check lights Lighting the Grill DANGER Failure to open the
41. tank in enclosed spaces such as a carport garage porch covered patio or other building Never leave a LP tank inside a vehicle which may become overheated by the sun Do not store LP tank in an area where children play LP Tank Filling Use only licensed and experienced dealers LP dealer must purged tank before filling Dealer should NEVER fill LP tank more than 80 of LP tank volume Volume of propane in tank will vary by temperature A frosty regulator indicates gas overfill Immediately close LP tank valve and call local LP gas dealer for assistance Do not release liquid propane LP gas into the atmosphere This is a hazardous practice To remove gas from LP tank contact an LP dealer or call a local fire department for assistance Check the telephone directory under Gas companies for nearest certified LP dealers LP Tank Exchange Exchange your Type 1 cylinder with OPD safety feature equipped ONLY Always keep new and exchanged LP tanks in upright position during use transit or storage Leak test new and exchanged LP tanks BEFORE connecting to grill Large Capacity Propane Tanks and Homes e LP Liquid Propane Coyote Grills can be installed into propane fueled houses Meaning that if your entire house is plumbed for propane and you have an exterior connection for such use then a standard LP grill from Coyote will meet your needs regardless of the size Any appliance can be installed if installed pr
42. uld be disconnected To reduce the chance of FLASHBACK the procedure below should be followed at least once a year or when your grill has not been used for an extended period of time wae A CCX2LP NG Built In Main Burners 1 2 Remove your grill from the island once the gas line and transformer are disconnected At the back of the grill you will find two cotter pins holding the burner in place 1st picture shown below Remove these cotter pins and carefully remove each burner by pulling up and away from the gas valve in front Use a wire brush on the outer surface of the burner to remove any food debris and or dirt Clean any clogged ports with a stiff wire such as an open paper clip Inspect the burner for damage cracks or holes and if such damage is found order and install a new burner After re installation check to insure that gas valve orifices are correctly placed inside the ends of burners and also check to make sure the position of the spark electrode is in its correct spot CCX2LP NG FS Free Standing Main Burners 1 Sa To remove the burners from the free standing grills you will need to remove the four bolts that hold the grill head to the cart 2nd picture shown below Next pull the back of the grill up on top of the cart 3rd picture shown below Now disconnect your gas line from the back of the grill You can now either remove the entire grill head from the cart or simply slide the grill forward on
43. upply turned off at the cylinder If your grill is set up for use with Natural Gas turn off gas supply at the system manual shut off valve DRIP TRAY The drip tray located below the grill should be cleaned periodically to prevent heavy buildup of debris NOTE Allow the drip tray to cool before attempting to clean IMPORTANT Do not leave the grill outside during inclement weather unless it is covered cover sold separately Rain water can collect inside the grill the grill cart or the drip tray if left uncovered If the drip tray is not cleaned after use and the grill is left uncovered the drip tray will fill with water causing grease and waiter to spill into the grill cart We recommend cleaning and storing the drip tray after every use COOKING GRATES The cooking grates can be cleaned immediately after cooking is completed and after turning off the grill Wear a barbecue mitt and scrub the cooking grates with a damp cloth If the grill is allowed to cool down cleaning the grates will be easier if removed from the grill and cleaned with a mild detergent FLAVORIZERS Washing the flavorizers after every use is not necessary but periodically it is suggested you wash them in a soap and warm water solution Use a wire brush to remove stubborn burned on cooking residue Dry the flavorizers thoroughly before you reinstall them in the cooking insert BURNERS IMPORTANT Gas control knobs should be in the OFF position and fuel line sho
44. urners If any problems or concerns exist about your location or elevation please contact Coyote Customer Service for assistance PA a d beon Gas Conversions Natural Gas and Propane Coyote grills are able to be converted but you must obtain the correct conversion kit and we always recommend that any gas appliance conversion should always be performed by a Licensed Plumber or a certified Installer Conversion kits are sold for Coyote grills and can be purchased through your dealer or Coyote s Customer Service Department Any other kit or orifices used that are not of Coyote brand will automatically void any warranty on the unit Furthermore it is important to understand that where ever there is a burner there is an orifice that will need to be changed The steps for converting your Coyote grills main burners are 1 2 10 11 12 Remove the grates and flavorizers from your grill Remove the locking pins on the burners a You will find these locking pins at the back of the unit If built in to an island you can slide the grill forward and reach these pins If the grill is located in a cart then you ca simply reach through the opening in the back and remove the pins Remove all of the burners from the grill Using a 6mm nut driver remove the orifice at the end of each valve Locate the new orifices from the conversion kit and apply pipe thread sealant to the threads on each orifice Using your fingers to ensure no cros
Download Pdf Manuals
Related Search