Home

JVC RX-778V

1. Make sure that you have set the speaker information correctly see page 14 e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel 1 Press DSP MODE repeatedly until 3D ACTION or 3D DIGITAL or 3D THEATER appears on the display The 3D PHONIC DSP PRO LOGIC and selected 3D PHONIC mode indicators also light up on the display DSP MODE SURROUND ADJUST P Adjust the effect level 1 Press BALANCE SURROUND ADJUST repeatedly until DSP EFFECT appears on the display The display changes to show the current setting e 2 Turn MULTI JOG to select the effect level e As you turn it the effect level changes as follows DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3 7 DSP EFFECT 5 DSP EFFECT 4 As the number increases the selected 3D PHONIC mode becomes stronger From the remote control 1 Press SURROUND MODE repeatedly until 3D ACTION or 3D DIGITAL or 3D THEATER appears on the display The 3D PHONIC DSP PRO LOGIC and selected 3D PHONIC mode indicators also light up on the display SURROUND 2 Press SOUND The 10 keys are activated for sound adjustments SOUND 3 Press EFFECT to select an effect level you want e Each time you press the button the effect level changes as follows DSP EFFECT 1 DSP EFFECT 2 gt DSP EFFECT 3 DSP EFFECT 5 lt
2. OVERLOAD starts flashing on the display Speakers are overloaded because of high volume Rotate the MASTER VOLUME control counterclockwise three or four times then press POWER on the front panel If OVERLOAD does not disappear unplug the AC power cord then plug it back again Speakers are overloaded because of short circuit of speaker terminals Press POWER on the front panel then check the speaker wiring If OVERLOAD does not disappear unplug the AC power cord then plug it back again If speaker wiring is not short circuited contact your dealer Remote control does not work The remote control mode selector is not set correctly Set the selector correctly either to AUDIO TV VCR or to CATV DBS There is an obstruction in front of the remote sensor on the receiver Remove the obstruction Batteries are weak Replace batteries 45 m Specifications Amplifier Output Power Audio Audio Input Sensitivity Impedance 1 kHz Audio Input DIGITAL IN Audio Output Level Signal to Noise Ratio 66 IHF 78 IHF Frequency Response 8 ohms RIAA Phono Equalization Loudness Control Volume Control at 30 dB SEA Video Video Input Sensitivity Impedance Composite video S video Video Output Level Composite video S video Synchronization Signal to Noise Ratio On Screen Color System 46 At Stereo operation 110 wat
3. 3 Adjust the effect level 1 Press BALANCE SURROUND ADJUST repeatedly until DSP EFFECT appears on the display The display changes to show the current setting as 2 Turn MULTI JOG to select the effect N level e As you turn it the effect level changes as follows DSP EFFECT 1 lt DSP EFFECT 2 DSP EFFECT i DSP EFFECT 5 DSP EFFECT 4 As the number increases the selected DAP mode becomes stronger SURROUND ADJUST From the remote control 1 Press SURROUND MODE SURROUND repeatedly until the DAP mode LIVE CLUB DANCE CLUB gt HALL or PAVILION appears on the display The DSP and selected DAP mode indicators also light up on the display SOUND 2 Press SOUND The 10 keys are activated for sound adjustments yy 3 Adjust the speaker output levels REAR L e To adjust the left rear speaker level press REAR L from 10 dB to 10 dB e To adjust the right rear speaker level press REAR R REAR R from 10 dB to 10 dB 4 Press EFFECT to select an effect EFFECT level you want e Each time you press the button the effect level changes as follows DSP EFFECT 1 DSP EFFECT 2 gt DSP EFFECT 3 DSP EFFECT 5 DSP EFFECT 4 4 As the number increases the selected DAP mode becomes stronger Adjusting the Surround Modes Once you have adjusted the Surround modes the adjustment is memorized for each Surround mode Dolby Surround adjus
4. then press lt Ice The SEA menu appears Press A V to move i tk to SEA MODE 10kHz eco OPERATE Press lt gt to select the SEA mode you want When you finish press EXIT repeatedly until the menu disappears from the TV 30 B Creating Your Own SEA Mode 1 Also see page 19 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move to SOUND CONTROL then press lt The SOUND CONTROL menu appears Press A V to move to SEA then press lt b gt The SEA menu appears Press A V to move to SEA ADJUST The SEA ADJUST menu appears Press A V lt 1 gt to adjust the SEA mode as you want lt 1 Select the frequency ranges A V Adjust the frequency levels Press SET to store the setting into the SEA USERMODE e If you press EXIT without pressing SET in this step you can return to the SEA menu The adjustment you have made is active but not stored SEA ADJUST SEA USERMODE When you finish press EXIT repeatedly until the menu disappears from the TV I Setting the Basic Setting Items Also see W Operating the Tuner Also see pages 17 and 18 pages 12 15 1 Press MENU 1 Press MENU The MAIN MENU appears on the TV The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays
5. TAPE MD Select the cassette deck or the MD recorder TV DBS e Select TV sounds when the remote control mode selector is set to AUDIO TV VCR e Select the DBS tuner when the remote control mode selector is set to CATV DBS To turn off the power into standby mode May PHONO Select the turntable press POWER again ear aa FM AM Select an FM or AM broadcast The STANDBY lamp lights up A small amount e Each time you press the button the band alternates Current volume level is shown here of power is consumed in standby mode To turn between FM and AM the power off completely unplug the AC power VCR Select the video component connected to the VCR cord jacks From the remote control Notes e When connecting an MD recorder to the TAPE MD jacks and a DBS tuner to the TV SOUND DBS jacks change the source name shown on the display For details see page 12 e When you press one of the source selecting buttons on the remote control marked above with an asterisk the receiver automatically turns on To turn on the power press AUDIO POWER ON The STANDBY lamp goes off The name of the current source or station frequency appears on the display To turn off the power into standby mode press AUDIO POWER STANDBY The STANDBY lamp lights up AUDIO POWER Selecting the Source to Play On the front panel Turn SOURCE SELECTOR until the source name you want appear
6. e DANCE CLUB e HALL e PAVILION e 3D ACTION or 3D DIGITAL By pressing SURROUND MODE e DOLBY SURROUND DOLBY PRO LOGIC DOLBY DIGITAL e THEATER or DIG THEATER e LIVE CLUB e DANCE CLUB DSP OFF DSP mode is canceled HALL e PAVILION 3D ACTION or 3D DIGITAL DSP OFF DSP mode is canceled To activate the Surround mode press DOLBY SURROUND button so that the lamp on the button lights up To activate the Surround mode you can also use the SURROUND ON OFF button Note on the center speaker sound when using the DAP modes Sounds come out of the center speaker only if the following take place at the same time e If CENTER SPK is set to LARGE or SMALL e If the center channel signals come into this receiver C of the signal indicators lights up see page 10 while playing a multi sound source encoded with Dolby Digital In this case you cannot adjust the center speaker output level 22 IMPORTANT When using the remote control check to see if its remote control mode selector is set to the correct AUDIO a TV VCR position L To operate this receiver set it to AUDIO TV arena p VCR except when selecting the DBS tuner as the source Adjusting the 3D PHONIC Modes Once you have adjusted the 3D PHONIC modes the adjustment is memorized for each 3D PHONIC mode Before you start remember
7. e Turning it clockwise decreases the left channel output e Turning it counterclockwise decreases the right channel output MULTI JOG Q Changing the Source Name When you have connected an MD recorder to the TAPE MD jacks or the DBS tuner to the TV SOUND DBS jacks on the rear panel change the source name shown on the display when you select the MD recorder or DBS tuner as the source On the front panel ONLY 1 When changing the source name SSUES from TAPE to MD e Turn SOURCE SELECTOR until TAPE appears When changing the source name from TV SOUND to DBS e Turn SOURCE SELECTOR until TV SOUND appears 2 Press and hold SOURCE NAME LOUDNESS until ASSGN MD or ASSGN DBS appears on the display SOURCE NAME 12 To change the source name to TAPE or TV SOUND repeat the same procedure above in step 1 select MD or DBS then press and hold SOURCE NAME LOUDNESS Note Without changing the source name you can still use the connected components However there may be some inconvenience TAPE or TV SOUND will appear on the display when you select the MD recorder or DBS tuner You cannot use the digital input see page 13 for the MD recorder and the DBS tuner You cannot use the COMPU LINK remote control system see page 33 to operate the MD recorder Setting the Subwoofer Information Register whether
8. set ENTER PERFORMER screen appears EID BACK 3 Press A V lt 1 to move cin front of a character you want then press SET to enter the character e If the current CD is a CD Text go to step 5 without entering the performer To use the lower case letters press A V lt to move C gt to SHIFT then press SET To use the upper case letters again press A V lt 1 to move to SHIFT then press SET 37 4 Repeat step 3 until you finish putting a performer name up to 32 characters To insert a space press A V lt 1 gt to move to SPACE then press SET To correct an incorrect character 1 Press A V lt 1 gt to move to or gt then press SET until the incorrect character is selected 2 Press A V lt D gt to move to CANCEL then press SET to erase the character 3 Press A V lt 1 gt to move C in front of the correct character then press SET to enter a correct character Xi BACK 5 Press A V lt 1 gt to move c to DISC 1 MICHAEL in this example then press SET The TITLE INPUT DISC TITLE screen appears 6 Enter the disc title referring to steps 3 and 4 e If the current CD is a CD Text go to the next step without entering the disc title ko ll e m J U gt 0 E SET MEMORY Ex BACK 7 Press A V lt gt to move c to DISC 1 MY FAVORITE in this example then press SET The TITLE
9. DSP EFFECT 4 2 As the number increases the selected 3D PHONIC mode becomes stronger Adjusting the DAP Modes Once you have adjusted the DAP modes the adjustment is memorized for each DAP mode EFFECT Before you start remember e Make sure that you have set the speaker information correctly see page 14 e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again e You cannot adjust the rear speaker output level when you have set REAR SPK to NONE See page 14 e When the DAP mode is used with the SEA mode see page 19 sounds may be distorted If this happens turn off the SEA mode On the front panel 1 Press DSP MODE repeatedly until the DAP mode LIVE CLUB DANCE CLUB HALL or PAVILION appears on the display The DSP and selected DAP mode indicators also light up on the display e When you have set REAR SPR to NONE the 3D PHONIC indicator also lights up DSP MODE 2 Adjust the speaker output levels 1 Press BALANCE SURROUND ADJUST repeatedly until one of the indications appears on the display REAR L LEVEL To adjust the left rear speaker level REAR R LEVEL To adjust the right rear speaker level 2 Turn MULTI JOG to adjust the selected speaker output level from 10 dB to 10 dB 3 Repeat 1 and 2 to adjust the other speaker output level SURROUND ADJUST MULTI JOG Q 23
10. RS LS CNTR Adjust the speaker output levels e To adjust the center speaker level press CNTR from 10 dB to 10 dB REARL e To adjust the left rear speaker level press G9 C REAR L from 10 dB to 10 dB e To adjust the right rear speaker level press REAR amp R from 10 dB to 10 dB ee TEST Press TEST again to stop the test tone EFFECT Press EFFECT to select an effect level you want e Each time you press the button the effect level changes as follows DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3 DSP EFFECT 5 lt DSP EFFECT 4 _ As the number increases JVC Theater Surround becomes stronger 26 On the front panel You can also use the buttons on the front panel to adjust the Surround modes However no test tone is available when using the buttons on the front panel So make adjustments while listening to the sound of the source played back 1 DSP MODE Press DSP MODE repeatedly until THEATER or DIG THEATER appears on the display e When THEATER is selected the PRO LOGIC DSP and THEATER indicators light up on the display e When DIG THEATER is selected the DSP and THEATER indicators light up on the display Adjust the speaker output levels 1 Press BALANCE SURROUND ADJUST repeatedly until one of the indications appears on the display CENTER LEVEL To adjust the center speaker level REAR L LE
11. Usable Sensitivity 50 dB Quieting Sensitivity Signal to Noise Ratio IHF A weighted Total Harmonic Distortion Stereo Separation at REC OUT Alternate Channel Selectivity Frequency Response AM tuner Tuning Range Usable Sensitivity Signal to Noise Ratio General Power Requirements Power Consumption Dimensions W x H x D Mass 87 5 MHz to 108 0 MHz Monaural 17 0 dBf 1 95 uV 75 ohms Monaural 21 3 dBf 3 2 uV 75 ohms Stereo 41 3 dBf 31 5 uV 75 ohms Monaural 78 dB at 85 dBf Stereo 73 dB at 85 dBf Monaural 0 4 at 1 kHz Stereo 0 6 at 1 kHz 35 dB at 1 kHz 45 dB 400 kHz 30 Hz to 15 kHz 0 5 dB 3 dB 530 kHz to 1 710 kHz Loop antenna 400 uV m 50 dB 100 mV m AC 120V v 60 Hz 320 watts 420 VA at operation 2 watts in standby mode 435 x 157 x 412 5 mm 17 16 x 6 3 16 x 16 4 inches 11 3 kg 25 0 Ibs Designs amp specifications are subject to change without notice 47 QUALITY JVC SERVICE HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE 1 800 537 5722 http www jvcservice com Dear customer In order to receive the most satisfaction from your purchase read the instruction booklet before operating the unit In the event that repair is necessary or for the address nearest your location please refer to the factory service center list below or within the Continental United States Call 1 800 537 5722 for your authorized servicer Remembe
12. When shipped from the factory the DIGITAL IN terminals can be used as the digital input for the following components DIGITAL 1 For DVD player DIGITAL 2 For CD player Selecting the Analog or Digital Input Mode When you have connected some components such as CD player MD recorder DVD player and the DBS tuner using digital terminals see page 8 you need to change the input mode for these components to the digital input On the front panel 1 Turn SOURCE SELECTOR until the source CD MD DBS or DVD for which you want to change the input mode from analog input to digital input appears on the display SOURCE_SELECTOR 2 Press INPUT ANALOG DIGITAL to change the input mode e Each time you press the button the input mode alternates between the digital input and analog input INPUT ANALOG DIGITAL From the remote control TAPE MD 1 Press the source selecting om button CD TAPE MD TV es DBS or DVD for which you AS want to change the input mode from analog input to digital input 2 Press ANALOG DIGITAL to change the input mode e Each time you press the button the input mode alternates between the digital input and analog input ANALOG DIGITAL Notes Before pressing TV DBS make sure that the remote control mode selector on the remote control is set to CATV DBS Once you have set the digital input for these components it is always used every time y
13. move C up and down and lt to select adjust or set the item Note The on screen display will disappear if no operation is done for about 1 minute 2 Press A V to move to SOURCE 3 Press lt to select the source 4 When you finish press EXIT The menu disappears from the TV 28 Wi Selecting the Different Source for Picture 1 and Sound Also see page 10 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move to VISUAL Press lt gt to select a different video source When you finish press EXIT The menu disappears from the TV E Activating the DSP Modes Also see page 27 1 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move to MODE Press lt gt to select the DSP mode you want to use When you finish press EXIT The menu disappears from the TV W Adjusting the Front Speaker Output Balance 1 Also see page 12 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move to SOUND CONTROL then press lt The SOUND CONTROL menu appears Press A V to move souND contRoL to BAL Balance xx SURROUND LEV
14. A V lt buttons also displays the MAIN MENU 2 Press A V to move to SOUND CONTROL then press lt gt The SOUND CONTROL menu appears 3 4 5 Press A V to move ssounomcontrot to SUBWFR LEVEL Press lt gt to adjust the subwoofer output level SURROUND LEVEL SEA c O czor oucr cu mics OPERATE When you finish press EXIT repeatedly until the menu disappears from the TV Wl Adjusting the DSP Modes Also see pages 23 26 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move to MODE DSP mode you want to adjust e In this example THEATER is selected Press A V to move to SOUND SOUND CONTROL CONTROL then ome SURROUND LEVEL press lt 1 gt The SOUND CONTROL menu appears Press A V to move to SURROUND LEVEL then press a b The SURROUND LEVEL menu appears mG OPERATE Press A V to move c to the item you want to set or adjust then press lt On these adjustment menus you can do the following For 3D PHONIC 3D ACTION 3D DIGITAL 3D THEATER DSP EFFECT Select the effect level For DAP LIVE CLUB DANCE CLUB HALL PAVILION REAR L LEVEL Adjust the left rear speaker output level REAR R LEVEL Adjust the right rear speaker output lev
15. Chanel number To operate the CATV converter and DBS tuner Note o set it to CATV DBS Refer to the manual supplied with your TV 6 Try to operate your TV by pressing TV CATV DBS POWER T When your TV turns on or off you have entered the correct code If there are more than one code listed for your brand of TV try each one until the correct one is entered Manufacturer Code Manufacturer Code JVC SAMSUNG HITACHI SANYO MAGNAVOX SHARP MITSUBISHI SONY PANASONIC 5 TOSHIBA RCA ZENITH Manufacturers codes are subject to change without notice If they are changed this remote control cannot operate the equipment 43 To change the transmittable signals for operating a CATV converter or DBS tuner 1 Set the remote control mode to CAT V DBS 2 Press and hold TV CATV DBS POWER 3 Press TV DBS 4 Enter manufacturer s code three digits using buttons 1 9 and 0 See the list below Examples For a Pioneer product press 1 then 3 For a Sony product press 2 then 0 5 Release TV CATV DBS POWER After setting the remote control mode selector to CATV DBS you can perform the following operations on the CATV convertor or on the DBS tuner TV CATV DBS POWER Turns on and off the CATV converter or DBS tuner CHANNEL Changes the channels 1 10 0 100 10 Selects the channel 100 10 button will function as the ENTER button if your equipm
16. INPUT DISC 1 GENRE screen appears 8 Press A V to move c to the genre you want then press SET The Disc Information screen appears again To show the unseen genres press A V until they appear 38 For the MD recorder You can write the disc information disc title and song titles into the disc You can only write the song title for the song currently selected e If you have the CD MD combination deck you can also enter the disc information its performer disc title and its music genre of normal audio CDs into the memory built in the CD MD combination deck To do this follow the procedure of For the CD Player with the disc memory function to the left e If you change the disc or song title with more than 32 characters the characters following 32nd will be erased from the title 1 Press TEXT DISPLAY while MD is selected as the source The Disc Information screen appears on the TV 2 Press A V to move SOURCE MD to TITLE INPUT Go then press SET at TRACK The DISC TITLE INPUT Tauck screen appears 3 Enter the title referring to steps 3 and 4 of For the CD Player with the disc memory function to the left e You can enter up to 32 characters for the disc title 4 Press A V lt 1 gt to move c to the disc title sources p JVC x SONG TITLE INPUT you have just entered Ji then press SET t The disc title is stored into the memor
17. MD recorder IMPORTANT If you turn on the receiver before turning on the other components after connecting the components the TEXT COMPU LINK remote control system does not work correctly If this happens 1 Turn off all the components including this receiver 2 Turn on the connected components 3 Turn on this receiver OPERATIONS To use this remote control system you need to connect the TV to the MONITOR OUT jack on the rear panel see page 7 and set the TV s input mode to the proper position to which the receiver is connected Make sure you have connected the CD player or MD recorder equipped with the TEXT COMPU LINK remote control system If not you cannot use the following functions On Screen Operation buttons on the remote control Hi Showing the Disc Information on the TV Screen Press TEXT DISPLAY while CD or MD is selected as the source The Disc Information screen appears on the TV SOURCE CD v SERACH TITLE INPUT Source name CD or MD Select F or K2 then press SET to change the disc Track numbers and track titles e The current playing selected track is indicated in yellow e When you move C toa track number you can change the track information by pressing lt gt Each time you press the button track information alternates between its track title and its performer You can also start playing the track b
18. TV volume to the minimum using the TV volume control on the TV 7 Turn on the other connected components first then turn on this receiver e When turning on the VCR use the remote control supplied with this receiver press VCR POWER The AV COMPU LINK remote control system allows you to use the five basic functions listed below Remote Control of the TV DVD player and VCR Using This Remote Control See page 42 for details For the DVD player and the VCR e Aim the remote control directly at the remote sensor on each component For the TV having AV COMPU LINK terminal RECEIVER AMP e Aim the remote control directly at the remote sensor on the receiver when operating the TV For the TV having AV COMPU LINK terminal AV COMPU LINK EX e Aim the remote control directly at the remote sensor on the TV when operating the TV 40 J One Touch Video Play Simply by inserting a video cassette without its safety tab into the VCR you can enjoy the video playback without setting other switches manually The receiver automatically turns on and changes the source to VCR The TV automatically turns on and changes the input mode to the position so that you can view the playback picture When you insert a video cassette with its safety tab press the play button on the VCR or on the remote control So you can get the same result Jf One Touch DVD Play Simply by starting playback on the DVD p
19. alternates between its disc title and its performer e Starting a disc play and going to the Disc Information screen see page 35 Press A V to move C to a searched disc then press SET Showing unseen disc information if more than 5 discs are listed as a result of the search Press A V until they appear e Going back to the GENRE SEARCH screen Press EXIT I Entering the Disc Information For the CD Player with the disc memory function You can use the disc memory function through this receiver The disc information its performer disc title and music genre of normal audio CDs will be stored into the memory built in the CD player For the disc memory function refer to the manual supplied with your CD player e The performer disc title and music genre information are usually recorded in a CD Text However if a CD Text has no genre information recorded in the disc itself you can input its music genre by yourself Note You can enter the TITLE INPUT screens for a CD Text and input its titles However you cannot store the titles you have input for a CD Text Example Entering the following information for Disc 1 Performer MICHAEL Disc title MY FAVORITE 1 Press TEXT DISPLAY while CD is selected as the source The Disc Information screen appears on the TV 2 Press A V to move to TITLE INPUT lJ then press SET The TITLE INPUT ax
20. apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state JVC COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP x kx Se Se Se Se a a ae a a a a ae ae a a ae a a ee a a ae a a ee a a ee a ae ae a a ae ee REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY THIS WARRANTY DOES NOT APPLY FOR DETAILS OF REFURBISHED PRO DUCT WARRANTY PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT 1700 Valley Road Wayne NJ 07470 OF OF OF OF OF OF OF OF OH OF OH HF OF OF OF FH OF OF OF OF OF FH OF OF OH OF FH OF OH OF H FH HF HH HH HH HH HF HF HF OF H HF OF HF OF HF OF KF OF HF OF HF OH HF OH H KH KH Ra For customer use Enter below the Model No and Serial No which is located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No Purchase date Name of dealer gB en VICTOR COMPANY OF JAPAN LIMITED 0399HIMMDWJEM
21. beginning of the current or previous track Pl Skips to the beginning of the next track STOP Stops playing PAUSE Stops playing temporarily To release it press PLAY Note GC G9 nO gt For detailed menu operations refer to the CG z instructions supplied with the discs or the DVD player After pressing DVD these buttons can be used for the DVD menu operations TV You can always perform the following operations with the remote control mode selector set to AUDIO TV VCR TV CATV DBS POWER Turns on or off the TV TV VOL Adjusts the volume TV VIDEO Sets the input mode either TV or VIDEO After pressing TV DBS with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on a TV CHANNEL Changes the channels 1 9 0 100 Selects the channels RETURN Alternates between the previously selected channel and the current channel im Operating Other Manufacturers Video Equipment This remote control supplied with the receiver can transmit control To change the transmittable signals for signals for other manufacturers VCRs TVs CATV converters and operating another manufacturer s TV DBS tuners By changing the transmittable signals from preset ones to the other manufacturers you can operate the other manufacturer s components using this remote control 1 Set the remote control mode to AUDIO TV l VC
22. control system can allow you to search discs by the performer disc title and music genre With this disc search you can easily find the disc you want to play Disc Title Input If your CD player or MD recorder has the disc memory function you can input the following information about the normal audio CDs or MDs on the TV screen e For CDs Performer disc title and music genre e For MDs Disc title and song titles What is a CD Text In a CD Text some information about the disc its disc title performer composer arranger etc is recorded Notes e If your audio component has two COMPU LINK 3 SYNCHRO jacks you can use either one If it has only one COMPU LINK 3 SYNCHRO jack connect it so that it is the last item in the series of components For example the CD player in the diagram to the left If your audio component has two TEXT COMPU LINK jacks you can use either one If it has only one TEXT COMPU LINK jack connect it so that it is the last item in the series of components For example the CD player in the diagram to the left e TEXT COMPULINK SOURCE NOT CONNECTED appears on the display in the following cases When the connections explained to the left are not correctly done When you try to use the TEXT COMPULINK function a few seconds after you turn on the connected equipment This is not a malfunction of the units Refer also to the manuals supplied with your CD player or
23. disappears from the TV fet COMPU LINK Remote Control System The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver To use this remote control system you need to connect JVC audio components through the COMPU LINK 3 SYNCHRO jacks see below in addition to the connections using cables with RCA pin plugs see page 6 e Make sure that the AC power cords of these components are unplugged before connection Plug the AC power cords only after all connections are complete y 7 7 ION Ro 2a CD player ae Cassette deck m a ar MD recorder COMPU LINK 3 SYNCHRO Turntable IMPORTANT When turning on these connected components for the first time turn on the connected components first then turn on this receiver Notes e If your audio component has two COMPU LINK 3 SYNCHRO jacks you can use either one If it has only one COMPU LINK 3 SYNCHRO jack connect it so that it is the last item in the series of components For example the turntable or CD player in the diagram above To operate the cassette deck or MD recorder using the COMPU LINK remote control system set the source name correctly See page 12 Refer also to the manuals supplied with your audio components This remote control system allows you to use four functions listed below Remote Control through the Remote Sensor on
24. or not you have connected a subwoofer Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel 1 Press SETTING repeatedly until SUBWOOFER appears on the display The display changes to show the current setting SETTING 2 Turn MULTI JOG to register whether you have connected a subwoofer or not O e As you turn it the subwoofer setting alternates between YES or NO YES NO Select this when no subwoofer is used Digital Input DIGITAL IN Terminal Setting When you use the digital input terminals you have to register what components are connected to which terminals DIGITAL IN 1 2 Select this when a subwoofer is used Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel ONLY 1 Press SETTING repeatedly until DIGITAL IN appears on the display The display changes to show the current setting SETTING DIGITAL 2 terminal setting DIGITAL 1 terminal setting 2 Turn MULTI JOG to select the appropriate digital terminal setting Q e As you turn it the display changes to show the following 1 DYD 2 CD gt 1DVD2MD gt 1CD2MD 1CD2DBS gt back to the beginning 1 DVD 2 DBS gt 1MD2DBS gt Note
25. services shall be rendered by JVC during normal business hours at JVC authorized service centers Parts used for replacement are warranted only for the remainder of the Warranty Period All products and parts thereof may be brought to a JVC authorized service center on a carry in basis except for Television sets having a screen size 25 inches and above which are covered on an in home basis WHAT YOU MUST DO FOR WARRANTY SERVICE Return your product to a JVC authorized service center with a copy of your bill of sale For your nearest JVC authorized service center please call toll free 800 537 5722 If service is not available locally box the product carefully preferably in the original carton and ship insured with a copy of your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center the name and location of which will be given to you by the toll free number If you have any questions concerning your JVC Product please contact our Customer Relations Department WHAT IS NOT COVERED This limited warranty provided by JVC does not cover 1 Products which have been subject to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service or if affixed to any attachment not provided with the products or if the model or serial number
26. the Receiver You can control the connected audio components through the remote sensor on the receiver using this remote control Aim the remote control directly at the remote sensor on the receiver For details see pages 41 and 42 Automatic Source Selection When you press the play button on a connected component or on its own remote control the receiver automatically turns on and changes the source to the component On the other hand if you select a new source on the receiver or on the remote control the selected component begins playing immediately In both cases the previously selected source continues playing without sound for a few seconds Automatic Power On Off Standby only possible with the COMPU LINK 3 connection Both the CD player and cassette deck or MD recorder turn on and off standby along with the receiver When you turn on the receiver the CD player or cassette deck or MD recorder will turn on automatically depending on which component has been previously selected When you turn off the receiver both the CD player and cassette deck or MD recorder will turn off standby Synchronized Recording Synchronized recording means the cassette deck or MD recorder starts recording as soon as a CD or a record begins playing To use synchronized recording follow these steps 1 Put a tape in the cassette deck or an MD in the MD recorder and a disc in the CD player or a record o
27. the e Pressing one of the A V lt buttons also displays the MAIN MENU MAIN MENU 2 Press A V to move 2 Press A V to move aaa to TUNER to SETTING then i are CONTROL then press lt gt A SEK ir DAROE press lt The SETTING or SETTING CNTR DELAY Smeec The TUNER CONTROL menu 2 menu appears CROSSOVER 1008 appears es ix EXT PAGE i EID OPERATE 3 Press A V to move go ENTER 3 Press A V to move c to the item you want to to the item you want to set or adjust then press lt set or adjust then press sert On the TUNER CONTROL menu you can do the following lt gt Le To go to the SETTING 2 DIG STRESET CH Select a preset channel station gt to NEXT FL BAND Select the band eee Ag hed rx FREQUENCY Tune in a station manually PAGE then press lt 1 gt rv k 3 To go back to the SETTING FM MODE Select the FM reception mode PA ae OO ENTER PRESET MEMORY See Storing the Preset Stations on 1 menu move CG to PREVIOUS PAGE then press lt gt Note the next page On the SETTING 1 and 2 menus you can do the following Not displayed when an AM station is selected 4 When you finish press EXIT repeatedly until the SUBWOOFER Set the subwoofer information menu disapp ears from the TV see page 12 FRONT SPK Set the front speaker information see page 14 CENTER SPK Set the cente
28. CE SURROUND ADJUST repeatedly until SUBWEFR LEVEL appears on the display The display changes to show the current setting SURROUND ADJUST MULTI JOG Q 2 Turn MULTI JOG to adjust the subwoofer output level 10 dB to 10 dB From the remote control SOUND 1 Press SOUND The 10 keys are activated for sound adjustments SUBWOOFER 2 Press SUBWOOFER to adjust the subwoofer output level 10 dB to 10 dB VY 11 E Basic Settings Some of the following settings are required after connecting and positioning your speakers in your listening room while others will make operations easier IMPORTANT When using the remote control check to see if its remote control mode selector is set to the correct position To operate this receiver set it to AUDIO TV VCR except when selecting the DBS tuner as ARSA werk the source Adjusting the Front Speaker Output Balance If the sounds you hear from the front right and left speakers are unequal you can adjust the speaker output balance Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel ONLY 1 Press BALANCE SURROUND ADJUST repeatedly until L R BALANCE appears on the display The display changes to show the current setting BALANCE ADJUST Turn MULTI JOG to adjust the balance
29. CHANNEL Changes the TV channels on the VCR 1 10 0 100 10 Selects the TV channels 100 10 button will function as the ENTER button if your VCR requires pressing ENTER after selecting a channel number PLAY Starts playback lt lt Rewinds a video tape gt gt Fast winds a video tape STOP Stops operation PAUSE Pauses REC Starts recording or enters recording pause Notes e Refer to the manual supplied with your VCR e You can use either VCR button or the VCR CONTROL button to activate the buttons listed above If you press VCR the playing source also changes On the other hand if you press VCR CONTROL the playing source does not change Try to operate your VCR by pressing VCR POWER When your VCR turns on or off you have entered the correct code If there are more than one code listed for your brand of VCR try each one until the correct one is entered Manufacturer Manufacturer JVC 01 02 03 PHILIPS EMERSON 11 26 RCA FISHER 29 SAMSUNG FUNAI 10 14 15 16 SANYO GOLD STAR 12 SHARP HITACHI 04 SHINTOM MITSUBISHI 13 SONY NEC TOSHIBA PANASONIC ZENITH Manufacturers codes are subject to change without notice If they are changed this remote control cannot operate the equipment 5 Troubleshooting Use this chart to help you solve daily operational problems If there is any problem you cannot solve contact your JVC service center P
30. EL id i xx SEA GB L Press lt gt to adjust s the balance BOOG OPERATE When you finish press EXIT repeatedly until the menu disappears from the TV Listening at Low Volume Loudness Also see page 11 1 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU 2 Press A V to move c to SOUND CONTROL then press lt gt The SOUND CONTROL menu appears 3 Press A V to move sounp contRow to LOUDNESS SURROUND LEVEL SEA D xx xx BAL G LOUD INPU SUBW Qa 4 Press lt gt to turn the loudness ON or OFF gic OPERATE 5 When you finish press EXIT repeatedly until the menu disappears from the TV I Attenuating the Input Signal Also see page 11 1 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU 2 Press A V to move c to SOUND CONTROL then press lt gt The SOUND CONTROL menu appears 3 Press A V to move sounp contRoL to INPUT ATT A SURROUND LEVEL 4 Press lt gt to turn the 2 45 Input Attenuator mode SEW ATT ON or NORMAL mig OPERATE 5 When you finish press EXIT repeatedly until the menu disappears from the TV Hl Adjusting the Subwoofer Output Level Also see page 11 1 Press MENU The MAIN MENU appears on the TV e Pressing one of the
31. JVC MU AUDIO VIDEO CONTROL RECEIVER RX 778VBK gisita AP AUC OYRADIT IIN Py wwii Win Vir WV Bit TEXT COMADITT IAT vWF V III PARADI I IIAN vWVIV Y LIN lliiRemote lill W 3D PHONIC DO waar DIGITAL For Customer Use Enter below the Model No and Serial No which are located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No LVT0171 001A J Warnings Cautions and Others RISK OF ELECTRIC SHOCK DO NOT OPEN e CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Caution POWER switch Disconnect the mains plug to shut the power off completely The POWER switch in any position does not disconnect the mains line The power can be remote controlled The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE
32. ND again so that the lamp on the button goes off SURROUND OFF appears on the display DOLBY SURROUND Atl From the remote control 1 Press SURROUND ON OFF so that the lamp on the DOLBY SURROUND button on the front panel lights up e Each time you press the button the Dolby Surround turns on and off alternately e You can also turn on Dolby Surround by pressing SURROUND MODE See page 22 for more details SURROUND O 2 Select and play a sound source e To enjoy Dolby Pro Logic play back a software encoded with Dolby Surround and labeled with DOOporsysurrouno mark e To enjoy Dolby Digital play back a software encoded with Dolby Digital and labeled with OO mark DIGITAL SURROUND To cancel the Dolby Surround mode Press SURROUND ON OFF again SURROUND OFF appears on the display lt For the other DSP modes On the front panel 1 Press DSP MODE repeatedly until the mode you want appears on the display e Each time you press the button the DSP modes change See page 22 for more details DSP MODE 2 Select and play a sound source e To enjoy 3D PHONIC and JVC Theater Surround play back a software encoded with Dolby Surround and labeled with DO povey surround mark encoded with Dolby Digital and labeled with DO mark DIGITAL To cancel the DSP mode aoe Oe Press DSP MODE repeatedly until DSP OFF appears on the di
33. O When a program is broadcasted in stereo you will hear stereo sound when in monaural you will hear monaural sounds This mode is also useful to suppress static noise between stations The MUTE AUTO indicator lights up on the display MONO Reception will be improved although you will lose the stereo effect In this mode you will hear noise while tuning into the stations The MUTE AUTO indicator goes off on the display 18 Note When using the FM MODE MUTING button on the remote control be sure that the 10 keys are activated for tuner not for the CD and others See page 41 Assigning Names to Preset Stations You can assign a name of up to four characters to each preset station When a preset station is tuned in its assigned name will appear on the display Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again e You can use the following characters Space A Z and 0 9 On the front panel ONLY 1 Tune in a preset station See the left 2 Press TUNER SEA MEMORY TUNER MEMORY The preset channel number starts flashing for about 10 seconds viv CH ay i ay e If you turn MULTI JOG while the preset channel number is flashing you can change the preset channel number TUNER PRESET 3 Press TUNER PRESET while the preset channel number is flashing The first character position starts f
34. PK is set to LARGE sound comes out only if the subwoofer channel signals come into this receiver LFE of the signal indicators lights up see page 10 while playing a multi sound source encoded with Dolby Digital DAP modes The sound heard in a concert hall or club consists of direct sound and indirect sound early reflections and reflections from behind Direct sounds reach the listener directly without any reflection On the other hand indirect sounds are delayed by the distances of the ceiling and walls These direct sounds and indirect sounds are the most important elements of the acoustic surround effects The DAP mode can create these important elements and gives you a real being there feeling This mode can be used when the front speakers are connected to this receiver without respect to the rear center speaker connection You can select one of the following to your preference LIVE CLUB Gives the feeling of a live music club with a low ceiling DANCE CLUB Gives a throbbing bass beat HALL Gives clear vocal and the feeling of a concert hall PAVILION Gives the spacious feeling of a pavilion with a high ceiling Reflections from behind Early reflections Surround modes With this receiver you can use two types of the Surround mode Following modes cannot be used when only the front speakers are connected to thi
35. R When operating the other manufacturers components refer also to the manuals supplied with them To operate these components with 2 Press and hold TV CATV DBS POWER the remote control first you need to set the manufacturer s code each for VCR TV CATV converters and DBS tuner 3 Press TV DBS 4 Enter manufacturer s code two digits using buttons 1 9 and 0 See the list below Examples For a JVC product press 0 then 1 AUDIO POWER For a Hitachi product press 1 then 0 amp ae 5 Release TV CATV DBS POWER cs Es es The following buttons can be used for operating the TV with cs ANALOGIDIGITAL SLEEP the remote control mode selector set to AUDIO TV VCR gt OG TV CATV DBS POWER surowo JEST aa Turns on and off the TV wane lt i nisc gt Q CuO TV VOL Adjusts the volume TV VIDEO Sets the input mode either TV DO or VIDEO operations on a TV RETURN FM MODE MUTING Qd AUDIO N 6 TNR q i After pressing TV DBS with the remote control mode selector ey CATNIDES F set to AUDIO TV VCR you can perform the following CHANNEL Changes the channels A VOL EN Check to see if its remote 1 10 0 100 10 Selects the channels L control mode selector is set 100 10 button will function as to the correct position the ENTER button if your TV requires y Yq eonan To operate the audio pressing ENTER after selecting a E E
36. ROBLEM POSSIBLE CAUSE SOLUTION The display does not light up The power cord is not plugged in Plug the power cord into an AC outlet No sound from speakers Speaker signal cables are not connected Check speaker wiring and reconnect if necessary The SPEAKERS 1 and 2 buttons are not set correctly Press SPEAKERS 1 and 2 correctly An incorrect source is selected Select the correct source Muting is activated Press MUTING to cancel the mute Sound from one speaker only Speaker signal cables are not connected properly Check speaker wiring and reconnect if necessary The balance is set to one extreme Adjust the balance properly see page 12 Continuous hiss or buzzing during FM reception Incoming signal is too weak Connect an outside FM antenna or contact your dealer The station is too far away Select a new station An incorrect antenna is used Check with your dealer to be sure you have the correct antenna Antennas are not connected properly Check connections Occasional cracking noise during FM reception Ignition noise from automobiles Move the antenna farther from automobile traffic No colors on the on screen display The color system of the connected TV is not NTSC Connect an NTSC TV Howling during record playing Your turntable is too close to speakers Move speakers away from the turntable
37. S 1 or SPEAKERS 2 to select the speaker to use e Each time you press the button the lamp on the respective button turns on and off When the lamp on either button lights up the respective speakers are activated SPEAKERS je Note If you use any of the DSP modes other than the 3D PHONIC modes with both front speakers activated the speakers connected to the FRONT SPEAKERS terminals are deactivated Listening only with headphones 1 Connect a pair of headphones to the PHONES jack on the front panel Press SPEAKERS 1 and or 2 so that no lamps on the buttons are turned on N CAUTION Be sure to turn down the volume before connecting or putting on headphones as high volume can damage both the headphones and your hearing Muting the Sound From the remote control ONLY Press MUTING to mute the sound through all speakers and headphones connected MUTING appears on the display and the volume turns off the volume level indicator goes off To restore the sound press MUTING again so that OFF appears on the display Turning MASTER VOLUME on the front panel or pressing VOLUME on the remote control also restores the sound Listening at Low Volume Loudness Human ears are not sensitive to bass at low volume To compensate for this the loudness function automatically boosts the bass level as you lower the volume On the front panel ONLY Press LOUDNESS SOURCE NAME bri
38. THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION To reduce the risk of electrical shocks fire etc 1 Do not remove screws covers or cabinet 2 Do not expose this appliance to rain or moisture Caution Proper Ventilation For U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help To avoide risk of electric shock and fire and to protect from damage Locate the apparatus as follow
39. TI JOG 2 Turn MULTI JOG to select the low frequency effect attenuator level e As you turn it the display changes to show the following 0dB 10dB OdB Normally select this 10dB Select this when the bass sound is distorted Dynamic Range Compression Setting You can compress the dynamic range difference between maximum sound and minimum sound of the reproduced sound This is useful when enjoying surround sound at night e This function takes effect only when playing back a source using Dolby Digital On the front panel ONLY 1 Press SETTING repeatedly until D RANGE COMP Dynamic Range Compression appears on the display The display changes to show the current setting SETTING 2 Turn MULTI JOG to select the appropriate item about the compression level e As you turn it the display changes to show the following OFF gt MID gt MAX OFF Select this when you want to enjoy surround with its full dynamic range No effect applied MID Select this when you want to reduce the dynamic range a little Factory setting MAX Select this when you want to apply the compression effect fully Useful at night 15 Storing the Basic Settings and Adjustments One Touch Operation JVC s One Touch Operation function is used to assign and store different sound settings for each different playing source By using this function you do not have to change t
40. VEL To adjust the left rear speaker level REAR R LEVEL To adjust the right rear speaker level 2 Turn MULTI JOG to adjust the selected speaker output level from 10 dB to 10 dB 3 Repeat 1 and 2 to adjust the other speaker output levels SURROUND ADJUST MULTI JOG Q SURROUND ADJUST Adjust the effect level 1 Press BALANCE SURROUND ADJUST repeatedly until DSP EFFECT appears on the display The display changes to show the current setting MutT Joe 2 Turn MULTI JOG to select the effect level As you turn it the effect level changes as follows T DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3 DSP EFFECT 5 DSP EFFECT 4 As the number increases JVC Theater Surround becomes stronger Activating the DSP Modes You can use only one DSP mode at a time When a DSP mode is activated another DSP mode is canceled if in use For Dolby Pro Logic and Dolby Digital Surround On the front panel 1 Press DOLBY SURROUND so that the lamp on the button lights up e Each time you press the button the Dolby Surround turns on and off alternately DOLBY SURROUND 2 Select and play a sound source e To enjoy Dolby Pro Logic play back a software encoded with Dolby Surround and labeled with DO botsysurrouno mark e To enjoy Dolby Digital play back a software encoded with Dolby Digital and labeled with DO mark DIGITAL To cancel the Dolby Surround mode Press DOLBY SURROU
41. Y Press SLEEP repeatedly The SLEEP indicator lights up on the display and the shut off time changes as follows in minutes fo 00 eee iii When the shut off time comes The receiver turns off automatically SLEEP To check or change the time remaining until the shut off time Press SLEEP once The remaining time until the shut off time appears in minutes To change the shut off time press SLEEP repeatedly To cancel the Sleep Timer Press SLEEP repeatedly until SLEEP 00min appears on the display The SLEEP indicator goes off e Turning off the power also cancels the Sleep Timer Recording a Source You can record any source playing through the receiver to a cassette deck or an MD recorder connected to the TAPE MD jacks and the VCR connected to the VCR jacks at the same time While recording you can adjust the volume level without affecting the sound levels of the recording IMPORTANT e Before recording a digital source turn off the DSP mode see page 20 e While recording a digital source do not change the SEA mode see page 19 or DSP mode see page 20 otherwise recording will be interrupted Note The SEA modes and DSP modes cannot affect the recording while recording an analog source fa Receiving Radio Broadcasts You can browse through all the stations or use the preset function to go immediately to a particular station IMPORTANT When using the remote control chec
42. annot control the DBS tuner connected to the TV SOUND DBS jacks Notes e When connecting only the VCR or DVD player to this receiver connect it directly to the receiver using cable with the monaural mini plugs e Refer also to the manual supplied with your video components CONNECTIONS 2 CASE1 If the DVD player is equipped with the S video terminals DO NOT use these video terminals To Video input 1 owr or To Video input 2 CASE2 If the DVD player is not equipped with the S video terminals DVD player DO NOT use these video terminals a To Video input 2 39 1 If you have already plugged your VCR DVD player TV and this receiver into the AC outlets unplug their AC power cords first 2 Connect your VCR DVD player TV and this receiver using the cables with the monaural mini plugs not supplied e See CONNECTIONS 1 on the previous page 3 Connect the audio input output jacks on VCR DVD player TV and this receiver using the cables with RCA pin plug e See page 7 4 Connect the video input output jacks on VCR DVD player TV and this receiver using the cables with RCA pin plug or with S video plug e See CONNECTIONS 2 on the previous page 5 Plug the AC power cords of the components into the AC outlets 6 When turning on the TV for the first time after the AV COMPU LINK connection turn the
43. ation of the disc information Press A V to move F to a searched disc then press lt 1 Each time you press lt 1 the disc information alternates between its disc title and its performer e Starting a disc play and going to the Disc Information screen see page 35 Press A V to move C to a searched disc then press SET e Showing unseen disc information if more than 5 discs are listed as a result of the search Press A V until they appear e Going back to the DISC TITLE SEARCH screen Press EXIT Search for a disc by its genre 1 Press TEXT DISPLAY while CD is selected as the source The Disc Information screen appears on the TV SOURCE CD 2 Press A V to move DESC SEXRGH c to SEARCH then press SET The DISC SEARCH screen appears SET ENTER EU BACK 3 Press A V to move to GENRE then ARCH press SET PORAR The GENRE SEARCH SIC i lt Bo om D PZ screen appears want to 4 Press A V to move G to the genre yo search then press SET To show the unseen genres press A V until they appear Disc search starts then the SEARCH RESULT screen showing the disc titles appears SOURCE CD x 5 On the SEARCH RESULT screen you can do the following e Changing the indication of the disc information Press A V to move F to a searched disc then press lt gt Each time you press lt J gt the disc information
44. ation other than explained in this section e To control the MD recorder using the TEXT COMPU LINK remote control system you have to change the source name shown on the display from TAPE to MD See page 12 e Some special characters and marks cannot be displayed correctly 35 W Searching a for Disc Only for the CD player Search for a disc by its performer 1 Press TEXT DISPLAY while CD is selected as the source The Disc Information screen appears on the TV 2 Press A V to move to SEARCH then press SET The DISC SEARCH screen appears SOURCE CD DISC SEARCH SET ENTER BACK 3 Press A V to move to PERFORMER then press SET The PERFORMER SEARCH 0 eet 5 6 7 8 9 GED ENTER EX BACK screen appears 4 Press A V lt 1 gt to move c in front of the first character of the performer you want to search then press SET To correct the incorrect entry press A V lt 1 gt to move C in front of the correct character then press SET Note Symbols such as or cannot be available for search 5 Press SET again SOURCE CD Disc search starts then the tx SEARCH RESULT SEARCH RESULT screen showing the performers appears 6 On the SEARCH RESULT screen you can do the following e Changing the indication of the disc information Press A V to move C to a searched disc then press lt Each time you press lt the d
45. ator lights up when the signals encoded with Dolby Digital come into the receiver The Dolby Pro Logic decoder is used not only for the analog sources but also for the sources encoded with Dolby Digital in the following cases When only front channel signals are encoded When front channel and monaural rear channel signals are encoded IMPORTANT Before recording a digital source turn off the DSP mode Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories Confidential Unpublished Works 1992 1998 Dolby Laboratories Inc All rights reserved 21 Available DSP Modes According to the Speaker Arrangement Available DSP modes will vary depending on how many speakers are used with this receiver Make sure that you have set the speaker information correctly see page 14 Speaker arrangements Available DSP modes Each time you press DSP MODE on the front panel or SURROUND MODE on the remote control the DSP modes change as follows Front Front speaker speaker ZF e 3D THEATER e LIVE CLUB e DANCE CLUB e HALL e PAVILION 3D ACTION or 3D DIGITAL DSP OFF DSP mode is canceled ZF Each time you press DSP MODE on the front panel or SURROUND MODE on Front Front the remote control the DSP modes change as follows speaker speaker By pressing DSP MODE e THEATER or DIG THEATER e LIVE CLUB
46. audio source selecting buttons CD TAPE MD PHONO FM AM while viewing the picture from a video component such as the VCR or DVD player etc 2 Turn SOURCE SELECTOR to select the sound except the TV sound while the indication of the above step is still on the display From the remote control Notes Once you have selected a video source pictures of the selected source are sent to the TV until you select another video source e When you select TV SOUND as the source this function does not work 10 Adjusting the Volume On the front panel To increase the volume turn MASTER IFN VOLUME clockwise X To decrease the volume turn it counterclockwise e When you turn MASTER VOLUME rapidly the volume level also changes rapidly e When you turn MASTER VOLUME slowly the volume level also changes slowly VOLUME Xx CAUTION Always set the volume to the minimum before starting any source If the volume is set at its high level the sudden blast of sound energy can permanently damage your hearing and or ruin your speakers From the remote control To increase the volume press VOLUME To decrease the volume press VOLUME Note The volume level can be adjusted within the range of 0 minimum to 90 maximum Selecting the Front Speakers On the front panel ONLY When you have connected two pairs of the front speakers you can select which to use Press SPEAKER
47. ear Delay Time Setting Register the delay time of the sound from the rear speakers comparing that of the sound from the front speakers If the distance from your listening point to the rear speakers is equal to that to the front speakers select 0 msec As the distance to the rear speakers becomes shorter increase the delay time e msec increase or decrease in delay time corresponds to 11 7 16 inches 30 cm decrease or increase in distance e Rear delay time for Dolby Digital is to be set to 5 msec e When shipped from the factory delay time is set to 5 msec On the front panel ONLY 1 Press SETTING repeatedly until REAR DELAY appears on the display The display changes to show the current setting SETTING 2 Turn MULTI JOG to select the delay time of the rear speaker output O e Turn it clockwise to increase the delay time from 0 msec R DELAY 0ms to 15 msec R DELAY 15ms e Turn it counterclockwise to decrease the delay time from 15 msec R DELAY 15ms to 0 msec R DELAY Oms Crossover Frequency Setting Small speaker cannot reproduce the bass sound very well So if you have used a small speaker any for the front center or rear channels this receiver automatically reallocate the bass elements originally assigned to the channel for which you have connected the small speaker to another channel for which you have connected the large speaker To use this func
48. efly LOUDNESS to select the loudness function e Each time you press the button the loudness function turns on LOUDNESS ON and off LOUDNESS OFF Select LOUDNESS ON to activate the loudness function The LOUDNESS indicator lights up on the display Select LOUDNESS OFF to cancel it The indicator goes off Note The loudness function affects the front speaker sounds only Attenuating the Input Signal When the input level of the playing source is too high the sounds will be distorted If this happens you need to attenuate the input signal level to prevent the sound distortion On the front panel ONLY Press and hold INPUT ATT SOUND SELECT so that the ATT indicator lights up on the display e Each time you press and hold the button the Input Attenuator mode turns on INPUT ATT ON or off INPUT NORMAL Notes e This function is available only for the sources connected using the analog terminals e This function takes effect when the DSP mode is in use Adjusting the Subwoofer Output Level You can adjust the subwoofer output level if you have selected YES for the SUBWOOFER see page 12 Once it has been adjusted the receiver memorizes the adjustment Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel 1 Press BALAN
49. el DSP EFFECT Select the effect level 29 For Dolby Pro Logic TEST TONE Output a test tone CENTER LEVEL Adjust the center speaker output level REAR L LEVEL Adjust the left rear speaker output level REAR R LEVEL Adjust the right rear speaker output level For Dolby Digital Surround TEST TONE Output a test tone CENTER LEVEL Adjust the center speaker output level REAR L LEVEL Adjust the left rear speaker output level REAR R LEVEL Adjust the right rear speaker output level For JVC Theater Surround TEST TONE Output a test tone CENTER LEVEL Adjust the center speaker output level REAR L LEVEL Adjust the left rear speaker output level REAR R LEVEL Adjust the right rear speaker output level DSP EFFECT Select the effect level Notes Not displayed when REAR SPK is set to NONE see page 14 Not displayed when CENTER SPK is set to NONE see page 14 When you finish press EXIT repeatedly until the menu disappears from the TV a Selecting Your Favorite SEA Mode 1 Also see page 19 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move to SOUND CONTROL then press lt gt The SOUND CONTROL menu appears Press A V to move to SEA
50. elect a preset station number you want Press SET to store the setting When you finish press EXIT repeatedly until the menu disappears from the TV E Assigning Names to Preset Stations 1 Also see page 18 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move c to TUNER CONTROL then press lt The TUNER CONTROL menu appears Press A V to move to PRESET CH Press lt gt to select a preset station Press A V to move to PRESET MEMORY then press lt gt The PRESET MEMORY menu appears GED MEMORY ees OPERATE 32 6 Press A V to move to PRESET NAME then press SET The character entry screen appears 7 Press A V lt gt to move c infront of a character you want You can also select the following GPACE To enter space CANCED To erase the character 9 To go back to the previous character position or go to the next character position 8 Press SET to enter the selected character v uu nD g SPypD m mm mxn 9 Repeat steps 7 and 8 to enter up to four characters GED MEMORY DOO OPERATE 10 Press A V lt 1 gt to move to PRESET NAME then press SET to store the setting The TUNER CONTROL menu appears again OO ENTER 11 When you finish press EXIT repeatedly until the menu
51. ent requires pressing ENTER after selecting a channel number Note Refer to the manual supplied with your CATV converter or DBS tuner 6 Try to operate your CATV converter or DBS tuner by pressing TV CATV DBS POWER When your CATV converter or DBS tuner turns on or off you have entered the correct code If there are more than one code listed for your brand of CATV converter or DBS tuner try each one until the correct one is entered GI JERROLD 01 02 03 04 05 06 07 08 HAMLIN REGAL 15 16 17 18 PIONEER 13 14 RCA 19 SCIENTIFIC ATLANTA 09 10 SONY 20 ZENITH 11 12 Manufacturers codes are subject to change without notice If they are changed this remote control cannot operate the equipment To change the transmittable signals for operating another manufacturer s VCR 1 Set the remote control mode to AUDIO TV VCR 2 Press and hold VCR POWER 44 3 4 Press VCR Enter manufacturer s code two digits using buttons 1 9 and 0 See the list below Examples For a JVC product press 0 then 1 For a Funai product press 1 then 0 Release VCR POWER Following button can be used for operating the VCR with the remote control mode selector set to AUDIO TV VCR VCR POWER Turns on and off the VCR After pressing VCR or VCR CONTROL with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on the VCR
52. erienced in movie theaters The 3D PHONIC mode is the result of research on sound localization technology carried out at JVC for many years This mode can be used when the front speakers are connected to this receiver without respect to the rear center speaker connection e You can select either 3D ACTION or 3D THEATER to your preference when playing an analog or Linear PCM digital source e You can select either 3D DIGITAL or 3D THEATER to your preference when playing a Dolby Digital source 3D ACTION Best for action and war movies where the action is fast and explosive 3D DIGITAL Reproduces multi sound source encoded with Dolby Digital 3D THEATER Reproduces the sound field of a large theater This mode can be selected when only front speakers are connected to this receiver and REAR SPK and CENTER SPK is set to NONE see page 14 Note on the subwoofer sound when using the 3D PHONIC modes Sounds will or will not come out of the subwoofer according to the selected 3D PHONIC mode e With 3D ACTION selected No sound comes out e With 3D DIGITAL selected Sound comes out if the subwoofer channel signals come into this receiver LFE of the signal indicators lights up see page 10 while playing a multi sound source encoded with Dolby Digital e With 3D THEATER selected If FRONT SPK is set to SMALL sound comes out while playing any source If FRONT S
53. f the center speaker when CENTER SPK is set to NONE see page 14 e No test tone comes out of the rear speakers when REAR SPK is set to NONE see page 14 Ifthe TV is turned on and the proper video input is selected on the TV the test tone screen will appear on the TV The signal indicators also light on the display while the test tone comes out of the speakers L L Lights when the test tone comes out of Lo the left front speaker 4 C Lights when the test tone comes out of the center speaker R Lights when the test tone comes out of the right front speaker RS Lights when the test tone comes out of the right rear speaker LS Lights when the test tone comes out of the left rear speaker 4 Adjust the speaker output levels Gja e To adjust the center speaker level press S CNTR from 10 dB to 10 dB REARL e To adjust the left rear speaker level press C6 REAR L from 10 dB to 10 dB e To adjust the right rear speaker level press REAR R from 10 dB to 10 dB _REAR R S TEST S You can also use the buttons on the front panel to adjust the Surround modes However no test tone is available when using the buttons on the front panel So make adjustments while listening to the sound of the source played back 5 Press TEST again to stop the test tone On the front panel DOLBY SURROUND 1 Press DOLBY SURROUND to activate an appro
54. g DISC with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on a CD player changer PLAY Starts playing kaa Returns to the beginning of the current or previous track PP Skips to the beginning of the next track STOP Stops playing PAUSE Pauses playing To release it press PLAY 1 6 7 P Select the number of a disc installed in a CD player changer After pressing CD with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on the CD player changer 1 10 10 Selects a track number directly For track number 5 press 5 For track number 15 press 10 then 5 For track number 20 press 10 then 10 For track number 30 press 10 10 then 10 41 Turntable After pressing PHONO with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on a turntable PLAY STOP Starts playing Stops operations Cassette deck After pressing TAPE MD or TAPE CONTROL with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on a cassette deck PLAY Starts playing qa Fast winds the tape from right to left gt Fast winds the tape from left to right STOP Stops operations PAUSE Pauses playing To release it press PLAY REC Press this button with the PLAY button to start recording Press this bu
55. has been altered tampered with defaced or removed 2 Initial installation and installation and removal for repair 3 Operational adjustments covered in the Owner s Manual normal maintenance video and audio head cleaning 4 Damage that occurs in shipment due to act of God and cosmetic damage 5 Signal reception problems and failures due to line power surge 6 Video Pick up Tubes CCD Image Sensor Cartridge Stylus Needle are covered for 90 days from the date of purchase 7 Accessories 8 Batteries except the Rechargeable Batteries are covered for 90 days from the date of purchase There are no express warranties except as listed above THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT INCONVENIENCE LOSS OR ANY OTHER DAMAGES WHETHER DIRECT INCIDENTAL OR CONSEQUENTIAL INCLUDING WITHOUT LIMITATION DAMAGE TO TAPES RECORDS OR DISCS RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty last so these limitations or exclusions may not
56. he settings every time you change the source The stored settings for the newly selected source are automatically recalled The following can be stored for each source e Volume level see page 10 e Loudness see page 11 e Input attenuator mode see page 11 e Subwoofer output level see page 11 Balance see page 12 Analog digital input mode see page 13 e SEA modes see page 19 DSP modes 3D PHONIC mode settings see page 23 DAP mode settings see page 23 Surround mode settings see page 24 On the front panel ONLY To store the sound settings 1 Press ONE TOUCH OPERATION 1222 lt P T0v The ONE TOUCH OPERATION lamp lights wor up then the previously memorized settings are recalled 2 Adjust the sound using the functions listed above The newly adjusted settings are memorized To recall the sound settings With the ONE TOUCH OPERATION lamp lit the settings for the currently selected source are recalled when the source is selected To cancel the One Touch Operation function Press ONE TOUCH OPERATION so that the lamp goes off Even though the One Touch Operation function is canceled the recalled sound effects remain active Note If the source is FM or AM you can assign a different setting for each band 16 Using the Sleep Timer Using the Sleep Timer you can fall asleep to music and know the receiver will turn off by itself rather than play all night From the remote control ONL
57. isc information alternates between its performer and its disc title e Starting a disc play and going to the Disc Information screen see page 35 Press A V to move to a searched disc then press SET e Showing unseen disc information if more than 5 discs are listed as a result of the search Press A V until they appear e Going back to the PERFORMER SEARCH screen Press EXIT 36 Search for a disc by its disc title 1 Press TEXT DISPLAY while CD is selected as the source The Disc Information screen appears on the TV SOURCE CD DISC SEARCH Press A V to move G to SEARCH then press SET The DISC SEARCH screen appears GE ENTER EX BACK Press A V to move SOURCE CD JIVE c amp to DISC TITLE xx DISC TITLE SEARCH 1x then press SET The DISC TITLE SEARCH screen appears GE ENTER EID BACK Press A V lt 1 to move c in front of the first character of the disc title you want to search then press SET To correct the incorrect entry press A V lt gt to move C in front of the correct character then press SET Note Symbols such as or cannot be available for search SOURCE CD Press SET again xx SEARCH RESULT Disc search starts then the TOM RING SEARCH RESULT screen SM d showing the disc titles Ba appears on E BACK On the SEARCH RESULT screen you can do the following Changing the indic
58. ize of the cone speaker unit built in your speaker is greater than 4 4 inches 12 cm select LARGE and if it is smaller than 4 inches 12 cm select SMALL e If you have selected NO for the subwoofer setting you can only select LARGE for the front speaker setting e If you have selected SMALL for the front speaker setting you cannot select LARGE for the center and rear speaker settings 14 Center Delay Time Setting Register the delay time of the sound from the center speaker comparing that of the sound from the front speakers If the distance from your listening point to the center speaker is equal to that to the front speakers select 0 msec As the distance to the center speaker becomes shorter increase the delay time e msec increase or decrease in delay time corresponds to 11 is inches 30 cm decrease or increase in distance e When shipped from the factory delay time is set to 0 msec On the front panel ONLY 1 Press SETTING repeatedly until CENTER DELAY appears on the display The display changes to show the current setting SETTING 2 Turn MULTI JOG to select the delay time of the center speaker output Q e Turn it clockwise to increase the delay time from 0 msec C DELAY 0ms to 5 msec C DELAY 5ms e Turn it counterclockwise to decrease the delay time from 5 msec C DELAY 5ms to 0 msec C DELAY 0ms R
59. k to see if its remote control mode selector is set to the correct position To operate this receiver set it to AUDIO TV VCR except when selecting the DBS tuner as the source AUDIO UBT pel Tuning in Stations Manually On the front panel 1 Turn SOURCE SELECTOR to select the band FM or AM The last received station of the selected band is tuned in SOURCE_SELECTOR FIWAM TUNING ms MULTI JOG 2 Press FM AM TUNING 3 Turn MULTI JOG until you find the frequency you want e Turning it clockwise increases the frequency e Turning it counterclockwise decreases the frequency e When you turn MULTI JOG quickly the frequency keeps changing until a station is tuned in From the remote control 1 Press FM AM to select the band e Each time you press the button the band alternates between FM and AM FM AM 2 Press TUNING UP or TUNING DOWN repeatedly until you find the frequency you want e When you hold the button the frequency keeps changing until a station is tuned in TUNING UP DOWN TUNING Note When a station of sufficient signal strength is tuned in the TUNED indicator lights up on the display When an FM stereo program is received the STEREO indicator also lights up Using Preset Tuning Once a station is assigned to a channel number the station can be quickly tuned You can preset up to 30 FM and 15 AM stati
60. lashing CH he ag state fee aan adi MULTI JOG TUNER PRESET 4 Turn MULTI JOG to select the first character while the first character position is flashing CH a Cae anion noona Py 5 Press TUNER PRESET while a character you want is flashing The next character position starts flashing NAZA i n m 2S 6 Repeat steps 4 and 5 to enter up to four characters 7 Press TUNER SEA MEMORY TUNER MEMORY while the last selected character is flashing after you have assigned a name To erase the input characters Insert spaces using the same procedure described above E Using the SEA Modes The SEA Sound Effect Amplifier modes give you control of the way your music sounds IMPORTANT When using the remote control check to see if its remote control mode selector is set to the correct position To operate this receiver set it to AUDIO TV VCR except when selecting the DBS tuner as the source AUDIO Dii eee Selecting Your Favorite SEA Mode On the front panel Press SEA MODE repeatedly until the SEA mode you want appears on the display e Each time you press the button the SEA mode changes as follows SEA ROCK SEA MUSICAL SEA MOVIE J SEA COUNTRY SEA OFF SEA USERMODE SEA JAZZ d SEA MODE SEA ROCK Gives a heavy sound Both high and low frequencies are boosted SEA MUSICAL Enhances the mid frequency range which
61. layer you can enjoy the DVD playback without setting other switches manually When the DVD player is connected through the analog input jacks on this receiver and analog input is selected the receiver automatically turns on and changes the source to DVD When the DVD player is connected through the digital input terminal on this receiver and digital input is selected the receiver automatically turns on and changes the source to DVD DIGITAL The TV automatically turns on and changes the input mode to the position so that you can view the playback picture i Automatic Selection of TV s Input Mode e When you select TV SOUND as the source to play on the receiver the TV automatically changes the input mode to the TV tuner so that you can watch TV e When you select DVD or DVD DIGITAL VCR or DBS or DBS DIGITAL as the source to play on the receiver the TV automatically changes the input mode to the appropriate position either Video Input 1 or Video Input 2 so that you can view the playback picture Note When you select TV SOUND as the source on the receiver you cannot see the menu on the TV screen since the AV COMPU LINK remote control system automatically changes the TV s input mode to the TV tuner If you do not mind stopping listening to the TV sounds you can then show the on screen displays after changing the TV s input mode to the appropriate positio
62. n either Video Input 1 or Video Input 2 the receiver is connected to a Automatic Power On Off The TV VCR and DVD player turn on and off along with the receiver When you turn on the receiver e If the previously selected source is VCR the TV and VCR will turn on automatically If the previously selected source is TV SOUND or DBS or DBS DIGITAL only the TV will turn on automatically e If the previously selected source is DVD or DVD DIGITAL the TV and DVD player will turn on automatically When you turn off the receiver the TV VCR and the DVD player will turn off Note If you turn off the receiver while recording on the VCR the VCR will not turn off but continue recording fay Operating JVC s Audio Video Components You can operate JVC s audio and video components with this receiver s remote control since control signals for JVC components are preset in the remote control IMPORTANT To operate JVC s audio components using this remote control You need to connect JVC audio components through the COMPU LINK 3 SYNCHRO jacks see page 33 in addition to the connections using cables with RCA pin plugs see page 6 Aim the remote control directly at the remote sensor on the receiver If you use the buttons on the front panel or the menu function to choose a source the remote control will not operate that source To operate a source with the remote con
63. n the turntable 2 Press the record button and the pause I button on the cassette deck or MD recorder at the same time This puts the cassette deck or MD recorder into recording pause If you do not press the record button and pause II button at the same time the synchronized recording feature will not operate 3 Press the play gt button on the CD player or on the turntable The source changes on the receiver and as soon as play starts the cassette deck or MD recorder starts recording When the play ends the cassette deck or MD recorder enters recording pause and stops about 4 seconds later Notes e During synchronized recording the selected source cannot be changed If the power of any component is shut off during synchronized recording the COMPU LINK remote control system may not operate properly In this case you must start again from the beginning 33 f TEXT COMPU LINK Remote Control System The TEXT COMPU LINK remote control system has been newly developed to deal with the disc information recorded in the CD Text and MDs Using these information in the discs you can operate the CD player or MD recorder equipped with the TEXT COMPU LINK remote control system through the receiver CONNECTIONS To use this remote control system you need to connect the CD player and or MD recorder you want to operate following the procedures below 1 If you have already plugged your CD
64. ol mode selector set to AUDIO TV VCR SURROUND ON OFF Turns on or off the Surround modes Dolby Pro Logic and Dolby Digital SURROUND MODE Selects the DSP modes After pressing SOUND with the remote control mode selector set to AUDIO TV VCR you can perform the following operations SEA MODE Changes the SEA modes SUBWOOFER Adjusts the subwoofer output level CNTR Adjusts the center speaker output level REAReL Adjusts the left rear speaker output level REARsR Adjusts the right rear speaker output level EFFECT Selects the effect level TEST Turns on or off the test tone output Note After adjusting sounds press the corresponding source selecting button or DISC to operate your target source by using the 10 keys otherwise the 10 keys cannot be used for operating your target source CD player After pressing CD with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on the CD player PLAY Starts playing Ke Returns to the beginning of the current or previous track PP Skips to the beginning of the next track STOP Stops playing PAUSE Pauses playing To release it press PLAY 1 10 10 Selects a track number directly For track number 5 press 5 For track number 15 press 10 then 5 For track number 20 press 10 then 10 For track number 30 press 10 10 then 10 CD player changer After pressin
65. on the receiver For the TV operations E If the TV having the AV COMPU LINK terminal RECEIVER AMP aim the remote control directly at the remote sensor on the receiver E If the TV having the AV COMPU LINK terminal AV COMPU LINK EX aim the remote control directly at the remote sensor on the TV 42 VCR You can always perform the following operations with the remote control mode selector set to AUDIO TV VCR VCR POWER Turns on or off the VCR After pressing VCR or VCR CONTROL with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on the VCR 1 9 0 Selects the TV channels on VCR PLAY Starts playing lt lt Rewinds a tape gt Fast winds a tape STOP Stops operations PAUSE Pauses playing To release it press PLAY REC Press this button with the PLAY button to start recording Press this button with the PAUSE button to enter recording pause CHANNEL Changes the TV channels on the VCR Note You can use either VCR button or the VCR CONTROL button to activate the buttons listed above If you press VCR the playing source also changes On the other hand if you press VCR CONTROL the playing source does not change DVD player After pressing DVD with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on a DVD player PLAY Starts playing Haa Returns to the
66. ons To store the preset stations Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel ONLY 1 Tune in the station you want to preset see Tuning in Stations Manually e If you want to store the FM reception mode for this station select the FM reception mode you want See Selecting the FM Reception Mode on page 18 TUNED SHEM voume 2 Press TUNER SEA MEMORY Mahilig i ee a 4 Prnt TUNER MEMORY VOLUME EJ CH appears and the channel number position starts flashing on the display for about 10 seconds Tio ak 10k MULTI JOG Note You can use the 10 keys on the remote control to select the preset number When using the 10 keys be sure that they are activated for the tuner not for the CD and others See page 41 3 Turn MULTI JOG to select a channel number while the channel number position is flashing 4 Press TUNER SEA MEMORY TONERISEA MEMORY again while the selected channel number is flashing on the display The selected channel number stops flashing The station is assigned to the selected channel number CH TUNED SEE vou lees 1 100 ik 10k Ca 3 5 Repeat steps 1 to 4 until you store all the stations you want To erase a stored preset station Storing a new station on a used number erases
67. ont panel ONLY If you do not want to store your adjustment but rather want to adjust the SEA temporarily skip step 4 below SEA ADJUST 1 Press SEA ADJUST repeatedly until the frequency range 100Hz 1kHz or 10kHz you want appears on the display VOLUME aH EDR ra 7 VOLUME ES 7 100 ik 10k L MULTI JOG Q This FR means this adjustment can be applied to the front speakers only 2 Turn MULTI JOG to adjust the SEA level of the selected frequency range e Turning it clockwise increases the level Turning it counterclockwise decreases the level CSEA UFR ivig a i Z D p ik 10k 3 Repeat step 1 and 2 to adjust other frequency ranges if necessary SEA MEMORY To recall your own SEA adjustment Press SEA MODE repeatedly until SEA USERMODE appears 4 Press TUNER SEA MEMORY Your adjustment is stored into the SEA USERMODE To erase a stored adjustment Storing a new adjustment into SEA USERMODE erases the previously stored one 19 I Using the DSP Modes The built in Surround Processor provides three types of the DSP Digital Signal Processor mode 3D PHONIC made DAP Digital Acoustic Processor mode and Surround mode 3D PHONIC modes The 3D PHONIC mode gives you such a nearly surround effect as it is reproduced through the Dolby Surround decoder which is widely used to reproduce sounds with a feeling of movement like those exp
68. ou select these components as the source IMPORTANT The sampling rate converter built in this unit corresponds only to 32kHz 44 1kHz and 48kHz If the signals of a different sampling frequency come into this unit noise may occur Showing the Text Information on the Display When you have connected an MD recorder or CD player equipped with TEXT COMPU LINK remote control system see page 34 you can show the text information such as disc title or track song title on the display of this receiver To show it on the display follow the procedure below Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the front panel only 1 Press SETTING repeatedly until FL DISPLAY appears on the display The display changes to show the current setting SETTING 9 Turn MULTI JOG to select either a the source name or the text information to be shown on the display e As you turn it the display changes to show the following NORMAL TEXT NORMAL Source name appears during play TEXT Text information appears during play Notes e Though you have selected TEXT the source name such as CD or MD appears if a playing disc has no text information e Though you have selected NORMAL the setting is changed to TEXT in the following case If the power failure occ
69. player MD recorder and this receiver into the AC outlets unplug their AC power cords first 2 Connect your CD player MD recorder and this receiver as follows through the COMPU LINK 3 SYNCHRO jacks and TEXT COMPU LINK jacks 1 COMPU LINK 3 SYNCHRO jacks Use the cables with the monaural mini plugs not supplied with this receiver CD player COMPU LINK 3 SYNCHRO 2 TEXT COMPU LINK jacks Use the cables with the stereo mini plugs not supplied with this receiver TEXT COMPU LINK fe 4 MASTER UNIT 2 SLAVE UNIT 1 IMPORTANT Set the Master Slave Selector on the rear to 1 MASTER UNIT e 2 SLAVE UNIT is just for the serviceman s use The TEXT COMPU LINK remote control system does not function with the selector set to 2 SLAVE UNIT 3 Connect your CD player MD recorder and this receiver using the cables with RCA pin plugs see page 6 4 Plug the AC power cords of these components above into the AC outlets 5 When turning on these components for the first time turn on the connected components first then turn on this receiver 34 FUNCTIONS This remote control system allows you to use the functions listed below Displaying the Disc Information on the TV screen Disc information such as its performer and disc title and track titles only when a CD Text is selected is shown on the TV screen Disc Search Only for CD Player This remote
70. priate Surround mode PRO LOGIC or DOLBY DIGITAL e Each time you press the button the Surround mode turns on and off alternately e When PRO LOGIC is selected the PRO LOGIC indicator lights up on the display SURROUND 2 Adjust the speaker output levels CESUR 1 Press BALANCE SURROUND ADJUST repeatedly until one of the indications appears on the display CENTER LEVEL To adjust the center speaker level REAR L LEVEL To adjust the left rear speaker level REAR R LEVEL To adjust the right rear speaker level 2 Turn MULTI JOG to adjust the selected speaker output level from 10 dB to 10 dB 3 Repeat 1 and 2 to adjust the other speaker output levels MULTI JOG Q JVC Theater Surround adjustments Before you start remember Make sure that you have set the speaker information correctly see page 14 e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again e You cannot adjust the rear speaker output levels when you have set REAR SPK to NONE See page 14 e You cannot adjust the center speaker output level and center tone when you have set CENTER SPR to NONE See page 14 From the remote control 1 Press SURROUND MODE repeatedly until THEATER or DIG THEATER appears on the Se display e When THEATER is selected the PRO LOGIC DSP and THEATER indicator
71. r speaker information see page 14 REAR SPK Set the rear speaker information see page 14 CNTR DELAY Adjust the delay time of the center speaker output see page 14 REAR DELAY Adjust the delay time of the rear speaker output see page 14 CROSSOVER Set the crossover frequency see page 15 LFE ATT Set the low frequency effect attenuator level see page 15 COMP Set the dynamic range compression see page 15 DIGITAL 1 2 Set the digital input terminal see page 13 FL DISP Set whether or not to show the disc text information on the display see page 13 Notes Not adjustable when CENTER SPK is set to NONE see page 14 Not adjustable when REAR SPK is set to NONE see page 14 4 When you finish press EXIT repeatedly until the menu disappears from the TV 31 W Storing the Preset Stations Also see page 17 1 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Press A V to move to TUNER CONTROL then press lt 1 gt The TUNER CONTROL menu appears Tune into a station on the TUNER CONTROL menu referring to Operating the Tuner on the previous page Press A V to move to PRESET MEMORY then press lt gt The PRESET MEMORY menu appears GED MEMORY G3 OPERATE Press lt gt to s
72. r to retain your Bill of Sale for Warranty Service JVC JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP FACTORY SERVICE CENTER LOCATIONS 107 Little Falls Road 1500 Lakes Parkway 705 Enterprise Street Fairfield NJ 07004 2105 Lawrenceville GA 30243 5857 Aurora IL 60504 8149 973 808 9279 770 339 2522 630 851 7855 5665 Corporate Avenue 2969 Mapunapuna Place 10700 Hammerly Suite 110 Cypress CA 90630 0024 Honolulu HI 96819 2040 Houston TX 77043 714 229 8011 808 833 5828 713 935 9331 13 Cummings Park 8192 State Road 84 890 Dubuque Avenue Woburn MA 01801 Davie FL 33324 South San Francisco CA 94080 1804 781 376 9100 954 472 1960 650 871 2666 Sophisticated electronic products may require occasional service Just as quality is a keyword in the engineering and production of the wide array of JVC products service is the key to maintaining the high level of performance for which JVC is world famous The JVC service and engineering organization stands behind our products NATIONAL HEADQUARTERS JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP 1700 Valley Road Wayne NJ 07470 if you ship the product Don t service it yourself Pack your JVC unit in the original carton or one of equivalent size and strength Enclose with the unit a letter stating the CAUTION problem or symptom that exists and also a copy of the receiptor billof
73. s Front No obstructions open spacing Sides No obstructions in 10 cm from the sides Top No obstructions in 10 cm from the top Back No obstructions in 15 cm from the back Bottom No obstructions place on the level surface In addition maintain the best possible air circulation as illustrated Spacing 15 cm or more RX 778VBK Wall or obstructions Stand height 15 cm or more a Basic Operations The following operations are commonly used when you play any sound source IMPORTANT From the remote control When using the remote control check to see if its Press one of the source selecting buttons remote control mode selector is set to the correct DVD cD TAPE MD position Tver i I C C U To operate an audio system TV and VCR set it to AUDIO TV VCR canes TV DBS PHONO FM AM To operate a CATV converter and DBS tuner set it to CATV DBS ven gt Turning the Power On and Off Standby Selected source name appears On the front panel To turn on the power press POWER STANDBY The STANDBY lamp goes off The name of the current source or station frequency appears on the display DOBEES THEATER LIVE CLUB ACTION MEE voume Cc 9 CSE bance cius MUTE AUTO my 3D PHONC HALL LOUDNESS HH Bs PAVILION am steer LILI Current source name appears DVD Select the DVD player CD Select the CD player
74. s also light up on the display e When DIG THEATER is selected the DSP THEATER and OO DIGITAL indicators also light up on the display SURROUND SOUND 2 Press SOUND The 10 keys are activated for sound adjustments 25 3 TEST Press TEST to check the speaker output balance TEST TONE L starts flashing on the display and a test tone comes out of the speakers in the following order TEST TONE L_ TEST TONE C _ TEST TONE R Left front speaker Center speaker Right front speaker TEST TONE LS TEST TONE RS Left rear speaker Right rear speaker Notes You can adjust the speaker output levels without outputting the test tone e No test tone comes out of the center speaker when CENTER SPK is set to NONE see page 14 e No test tone comes out of the rear speakers when REAR SPK is set to NONE see page 14 e Ifthe TV is turned on and the proper video input is selected on the TV the test tone screen will appear on the TV The signal indicators also light on the display while the test tone comes out of the speaker L Lights when the test tone comes out of L CEJ R the left front speaker C Lights when the test tone comes out of z LS the center speaker R Lights when the test tone comes out of the right front speaker Lights when the test tone comes out of the right rear speaker Lights when the test tone comes out of the left rear speaker
75. s on the display As you turn the selector the source changes as follows SOURCE SELECTOR DVD cD CD PHONO TAPE or MD Z FM Z o a AM Z DVD Z TV SOUND or DBS Z nena Pioo VCR Z back to the beginning VCR TAPEMD m mi FM The selected source lamp also lights up AM ci When playing a digital source through a digital terminal The DIGITAL SOURCE FORMAT lamps on the front panel indicate what type of the digital signal comes into the receiver DOLBY DIGITAL Lights up when Dolby Digital signals see page 21 come in LINEAR PCM Lights up when Linear PCM signals come in DIGITAL SOURCE FORMAT DOLBY LINEAR DIGITAL PCM co cI e The signal indicators also light up on the display to indicate the incoming channel signals Only the indicators for the incoming signals light up L Left front channel R Right front channel C Center channel LS Left rear channel RS Right rear channel S Rear channel monaural Subwoofer channel CLICC ICR LFE Selecting different sources for picture and sound You can watch picture from a video component while listening to sound from another component On the front panel 1 Press SOUND SELECT INPUT ATT briefly while viewing the picture from a video component such as the VCR or DVD player etc SOUND SELECT appears on the display SOUND SELECT FAOD SOURCE SELECTOR Q Press one of the
76. s receiver without the rear speakers or center speaker Dolby Surround Dolby Digital and Dolby Pro Logic Used to reproduce the soundtracks of software encoded with Dolby Digital bearing the mark OO Petey or with Dolby Surround bearing the mark DOU l potsysurrounp Dolby Digital and Dolby Pro Logic can be selected automatically according to software played back and the speaker arrangement you have done e To enjoy the software encoded with Dolby Digital you must connect the source component using the digital terminal on the rear of this receiver See page 8 JVC Theater Surround In order to reproduce a more realistic sound field in your listening room while playing soundtracks of software encoded with Dolby Digital bearing the mark Oe with Dolby Surround bearing the mark DQ potsysurround you can use JVC Theater Surround e When playing a source encoded with Dolby Digital bearing the mark DOE DIG THEATER is selected automatically e When playing a source encoded with Dolby Surround bearing the mark DC powsysurrounn THEATER is selected automatically Notes The DSP modes have no effect on monaural sources The DSP modes cannot be used for recording an analog source The PRO LOGIC indicator lights up when the Dolby Pro Logic decoder built in this receiver is activated The OO DIGITAL indic
77. sale you received when you purchased your To prevent electrical shock do not open the cabinet No user JVC unit Print your home return address on the outside serviceable parts inside and the inside of the carton Send to the appropriate JVC Refer servicing to qualified service personnel Factory Service Center as listed above ACCESSORIES To purchase accessories for your JVC product you may contact your local JVC Dealer Or from the 48 Continental United States call toll free 800 882 2345 1098 F F F F HF OF HF OF F OF HF OF F F OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF OF kx k Se a ae a ae Se a a ae a a Se a a Se a a ae a a Se a a ae a a ee a ee ae a a ae a a JVC JVC COMPANY OF AMERICA warrants this product and all parts thereof except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP from the date of original retail purchase for the period as shown below The Warranty Period LIMITED WARRANTY AUDIO 2 PARTS 2YR LABOR 2YR THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY 50 UNITED STATES THE DISTRICT OF COLUMBIAAND IN COMMONWEALTH OF PUERTO RICO WHAT WE WILL DO If this product is found to be defective JVC will repair or replace defective parts at no charge to the original owner Such repair and replacement
78. splay From the remote control 1 Press SURROUND MODE repeatedly until the DSP mode you want appears on the display e Each time you press the button the DSP modes change You can also turn on Dolby Surround See page 22 for more details SURROUND V 2 Select and play a sound source e To enjoy 3D PHONIC and JVC Theater Surround play back a software encoded with Dolby Surround and labeled with DOpotsysurrouno mark encoded with Dolby Digital and labeled with OO fess mark DIGITAL To cancel the DSP mode Press SURROUND MODE repeatedly until DSP OFF appears on the display SURROUND V 27 Ei Using the On Screen Menus You can use the Menus on the TV screen to control the receiver To use this function you need to connect the TV to the MONITOR OUT jack on the rear panel see page 7 and set the TV s input mode to the proper position to which the receiver is connected e When the TVs input mode is incorrect for example a different video input or TV tuner mode is selected you cannot show the Menus on the TV screen On Screen Operation buttons on the remote control AUDIO POWER L J J Selecting the Source to Play Also see page 9 1 Press MENU The MAIN MENU appears on the TV e Pressing one of the A V lt buttons also displays the MAIN MENU Shows the buttons you can use on the current menu In this case use A V to
79. the human voice is mostly made up of SEA MOVIE Adds breadth to sounds so you feel like you are in a movie theater SEA COUNTRY Enhances the high frequency range so that instruments such the violin and banjo are emphasized SEA JAZZ Gives a feeling of a live atmosphere Good for acoustic music SEA USERMODE Your original SEA adjustment see the right SEA OFF No SEA mode is applied see below Notes The SEA modes cannot be used for recording When the SEA mode is turned on the SEA indicator lights up on the display When the SEA mode is used with the DAP mode see page 23 sounds may be distorted If this happens turn off the DAP mode or decrease the effect level of the DAP mode To cancel the SEA mode Press SEA MODE repeatedly until SEA OFF appears The SEA indicator goes off from the display From the remote control 1 Press SOUND The 10 keys are activated for sound adjustments 2 Press SEA MODE repeatedly until SEA MODE the SEA mode you want appears on the display To cancel the SEA mode Press SEA MODE repeatedly until SEA OFF appears in step 2 above The SEA indicator goes off from the display Creating Your Own SEA Mode You can adjust and store your own SEA adjustment into memory SEA USERMODE Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again On the fr
80. the previously stored one 17 To tune in a preset station On the front panel 1 Turn SOURCE SELECTOR to select the band FM or AM The last received station of the selected band is tuned in SOURCE_SELECTOR TUNER PRESET 2 Press TUNER PRESET 3 Turn MULTI JOG until you find the channel you want mum Joa FM AM e Turning it clockwise increases the channel numbers e Turning it counterclockwise decreases the channel numbers From the remote control 1 Press FM AM e Each time you press the button the band alternates between FM and AM 2 Press the 10 keys to select a preset channel number e For channel number 5 press 5 e For channel number 15 press 10 then 5 e For channel number 20 press 10 then 10 e For channel number 30 press 10 10 WS then 10 Note When you use the 10 keys on the remote control be sure that they are activated for the tuner not for the CD and others See page 41 Selecting the FM Reception Mode When an FM stereo broadcast is hard to receive or noisy You can change the FM reception mode while receiving an FM broadcast e You can store the FM reception mode for each preset station Press FM MODE on the front panel or FM MODE MUTING on the remote control e Each time you press the button the FM reception mode alternates between AUTO and MONO On the remote FM MODE SS On the front panel AUT
81. tion properly you need to set this crossover frequency level according to the size of the small speaker connected e This function takes effect only when playing back a source using Dolby Pro Logic or Dolby Digital However if you have selected LARGE for all speakers see page 14 this function will not take effect On the front panel ONLY 1 Press SETTING repeatedly until CROSSOVER FRQ Crossover Frequency appears on the display The display changes to show the current setting SETTING 2 Turn MULTI JOG to select the crossover frequency level according to the size of the small speaker connected e As you turn it the display changes to show the following 80Hz 100Hz 120Hz e Use the following comments as reference when adjusting 80Hz Select this when the cone speaker unit built in the speaker is about 4 3 4 inches 12 cm 100Hz Select this when the cone speaker unit built in the speaker is about 3 is inches 10 cm 120Hz Select this when the cone speaker unit built in the speaker is about 3 3 16 inches 8 cm Low Frequency Effect Attenuator Setting If the bass sound is distorted while playing back a source using Dolby Digital follow the procedure below On the front panel ONLY 1 Press SETTING repeatedly until LFE ATT Low Frequency Effect Attenuator appears on the display The display changes to show the current setting SETTING MUL
82. tments Before you start remember e Make sure that you have set the speaker information correctly see page 14 e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again You cannot adjust the rear speaker output levels when you have set REAR SPK to NONE See page 14 e You cannot adjust the center speaker output level when you have set CENTER SPK to NONE See page 14 From the remote control 1 Press SURROUND MODE repeatedly until the mode PRO LOGIC or DOLBY DIGITAL appears on the display e When PRO LOGIC is selected the PRO LOGIC indicator lights up on the display SURROUND Note You can also press SURROUND ON OFF to activate an appropriate Surround mode PRO LOGIC or DOLBY DIGITAL Each time you press the button the Surround mode turns on and off alternately 2 Press SOUND The 10 keys are activated for sound adjustments SOUND 3 Press TEST to check the speaker j output balance TEST TEST TONE L starts flashing on the display and a test tone comes out of the speakers in the following order TEST TONE L_ TEST TONE C _ TEST TONE R Left front speaker Center speaker Right front speaker TEST TONE LS TEST TONE RS Left rear speaker Right rear speaker Notes You can adjust the speaker output levels without outputting the test tone e No test tone comes out o
83. trol the source must be selected using source selecting buttons on the remote control To operate the cassette deck or MD recorder using the COMPU LINK remote control system set the source name correctly See page 12 Refer also to the manuals supplied with your components AUDIO POWER TWGATVIDES VCR DVD cD TAPEIMD TV DBS PHONO FMAM VCR ANALOG DIGITAL SLEEP Co SURROUND CNTR O SURROUND TEST REARL me G G O DISC EFFECT REARR OO SOUND SEA MODE SUBWOOFER RETURN FMMODE MUTING 100 iis Hee a Yor A i Boy a L CHANNEL VOLUME Check to see if its remote control mode selector is set A to the correct position o SD w To operate the audio eS ED system TVs and VCRs DOWN TUNING UP set it to AUDIO TV VCR DA ee RM SRX778J REMOTE CONTROL Tuner After pressing FM AM with the remote control mode selector set to AUDIO TV VCR you can perform the following operations FM AM 1 10 10 Alternates between FM and AM Selects a preset channel number directly For channel number 5 press 5 For channel number 15 press 10 then 5 For channel number 20 press 10 then 10 TUNING UP TUNING DOWN Tunes into stations FM MODE MUTING Changes the FM reception mode Sound control section Amplifier You can always perform the following operations with the remote contr
84. ts per channel min RMS driven into 8 ohms 20 Hz to 20 kHz with no more than 0 06 total harmonic distortion Front channels At Surround operation Front channels 100 watts per channel min RMS driven into 8 ohms at 1 kHz with no more than 0 8 total harmonic distortion 100 watts min RMS driven into 8 ohms at 1 kHz with no more than 0 8 total harmonic distortion Center channel Rear channels 100 watts per channel min RMS driven into 8 ohms at 1 kHz with no more than 0 8 total harmonic distortion PHONO MM 2 5 mV 47 k ohms CD TAPE MD TV SOUND DBS VCR DVD 200 mV 47 k ohms Optical DIGITAL 1 DVD DIGITAL 2 CD 21 dBm to 15 dBm 660 nm 30 nm Corresponding to Linear PCM and Dolby Digital with sampling frequency 32 kHz 44 1 kHz 48 kHz TAPE MD VCR 200 mV PHONO 70 dB 78 dB at REC OUT CD TAPE MD TV SOUND DBS VCR DVD 87 dB 80 dB PHONO 20 Hz to 20 kHz 1 dB CD TAPE MD TV SOUND DBS VCR DVD 20 Hz to 20 kHz 1 dB 1 0 dB 20 Hz to 20 kHz 6 1 0 dB at 100 Hz 4 1 0 dB at 10 kHz 100 Hz 1 kHz 10 kHz 10 dB 2 dB Center frequencies Control range TV SOUND DBS VCR DVD DVD Y luminance C chrominance burst 1 Vp p 75 ohms 1 Vp p 75 ohms 0 286 Vp p 75 ohms VCR MONITOR OUT 1 Vp p 75 ohms MONITOR OUT Y luminance 1 Vp p 75 ohms C chrominance burst 0 286 Vp p 75 ohms Negative 45 dB NTSC FM tuner IHF Tuning Range
85. tton with the PAUSE button to enter recording pause MD recorder After pressing TAPE MD or TAPE CONTROL with the remote control mode selector set to AUDIO TV VCR you can perform the following operations on the MD recorder PLAY Starts playing lt lt Returns to the beginning of the current or previous track PP Skips to the beginning of the next track STOP Stops playing PAUSE Pauses playing To release it press PLAY REC Press this button with the PLAY button to start recording Press this button with the PAUSE button to enter recording pause Note You can use either TAPE MD button or the TAPE CONTROL button to activate the buttons listed above If you press TAPE MD the playing source also changes On the other hand if you press TAPE CONTROL the playing source does not change IMPORTANT To operate JVC s video components using this remote control e You need to connect JVC video components through the AV COMPU LINK terminals see page 39 in addition to the connections using cables with RCA pin plugs see page 7 e Some JVC VCRs can accept two types of the control signals remote code A and B Before using this remote control make sure that the remote control code of the VCR connected to the VCR jacks is set to code A e When using the remote control For the DVD player and VCR operations aim the remote control directly at the remote sensor on each component not
86. urs If you unplug the AC power cord 13 Setting the Speakers for the DSP Modes To obtain the best possible surround sound of the DSP modes you have to register the information about the speakers arrangement after all connections are completed Before you start remember e There is a time limit in doing the following steps If the setting is canceled before you finish start from step 1 again Front Center and Rear Speaker Setting Register the sizes of all the connected speakers e When you change your speakers you need to register the information about the speakers again On the front panel ONLY 1 Press SETTING repeatedly until FRONT SPK Front Speaker CENTER SPK Center Speaker or REAR SPK Rear Speaker appears on the display The display changes to show the current setting SETTING 2 Turn MULTI JOG to select the appropriate item about the speaker selected in the above step e As you turn it the display changes to show the following LARGE gt SMALL gt NONE LARGE SMALL NONE Select this when the speaker size is relatively large Select this when the speaker size is relatively small Select this when you have not connected a speaker Not selectable for the front speakers 3 Repeat steps 1 and 2 to select the appropriate items for the other speakers Notes Keep the following comment in mind as reference when adjusting If the s
87. y and the SONG TITLE INPUT screen for the currently selected song appears e You can enter a song title for the song currently selected indicated in yellow on the TV screen Cc N Y 1 3 5 Enter the song title referring to steps 3 and 4 of For the CD Player with the disc memory function to the left e You can enter up to 32 characters for the song title 6 Press A V lt 1 gt to move c to the song title you have just entered then press SET The song title is stored into the memory and the Disc Information screen appears again Ka AV COMPU LINK Remote Control System The AV COMPU LINK remote control system allows you to operate JVC video components TV VCR and DVD player through the receiver To use this remote control system you need to connect the video components you want to operate follow the diagrams below and the procedure on the next page CONNECTIONS 1 DVD player Dre a i G o SSS rs so ooo IMPORTANT Connect to the terminal indicated in the illustration DO NOT connect to the TV terminal EX Dm receve x Ors amg gt gt gt B ja A If the AV COMPU LINK terminal on the TV is RECEIVER AMP N COMPULINK RECEIVER ANP If the AV COMPU LINK terminal on the TV is AV COMPU LINK sam wN COMPULINK EX CAUTION The AV COMPU LINK remote control system c
88. y pressing SET Select this move C gt in front then press SET to go to the DISC SEARCH screen see page 36 Select this move C in front then press SET to go to the TITLE INPUT screen see page 37 This appears only when a CD Text is selected Disc information such as the disc title performer and music genre When this is selected in front you can change the disc information by pressing lt Each time you press the button disc information see Note on changes Select FN or then press SET to change the track Usable buttons and their functions for the current selection Indication here will be changed according to what is currently selected in front on the screen See Note on Q ONO 90 OO Note on D The following information will appear on the display e For CD Text Disc title Performer Genre Song writer Composer Arranger Message For MD only Disc Title will appear Only recorded information will be shown If there is no data NO DATA will appear Note on For example the SET button will be used to start play PLAY to go to the next screen ENTER and to determine the selection ENTER To exit from the Disc information screen Press EXIT Notes e The on screen display will disappear in the following case if no operation is done for about 10 minutes if you do any oper

JVC RX-778V

Contents

Download Pdf Manuals

Related Search

Related Contents