Hoover U5167-900 Fold Away Upright Vacuum
Contents
1. Remove agitator and used belt Discard used belt Grasp agitator firmly and fit it into posi tion by first sliding end opposite the belt into the rectangular slot Q on side of cleaner Pull other side of agitator R into place Turn agitator making sure belt is not pinched between agitator and cleaner body The belt must rotate freely inside the belt guide If the agitator does not turn reposition belt in the belt guide Continued gt 9 Replace agitator cover N and 2 screws The agitator brush roll When to replace When agitator brushes are worn the agitator should be replaced To check condition of brushes discon nect cleaner from electrical outlet Move edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy When purchasing a new agitator ask for HOOVER part no 48414110 10 Replace hood 2 screws and hose How to replace Disconnect cleaner from electrical outlet Remove hood and agitator cover as described in the Belt replacement section Discard old agitator Continue following the directions in the Belt replacement section to replace belt new agitator agitator cover and hood Lubrication The motor is equipped with bearings that contain sufficient lubrication for the li2. N ou Ww o go 10 11 12 FoldAway handle Upper handle release button Dirt cup handle latch Carrying handle Dirt cup filter chamber Pleated filter inside filter chamber Dirt cup Headlight Stair cleaning handle located under the headlight Hood Carpet height adjustment knob rotate knob to cor rect setting for height of carpet being cleaned Handle release pedal step on pedal to lower handle to operating or low positions 13 14 15 16 Hose Furniture nozzle Dusting brush Extension wand 17 Crevice wand stores 18 19 inside wand Cord hooks wrap cord around hooks for storage The top hook rotates to the left for easy cord release ON OFF switch locat ed on left rear corner of cleaner body Handle positions The handle of your cleaner has three posi tions upright when using cleaning tools operating position for general operation on carpet and floors low for reaching under low furniture Step on handle release pedal to lower handle Transporting cleaner Put handle in upright position Tilt cleaner back on rear wheels Push forward L0W CARPET HARD FLOOR Carrying handle Use the carrying handle to lift the Cleaner Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle B When it is necessary to raise and lower the nozzle for various carpet pile heights t
3. Do not tap the soft pleated part of the filter It could damage the filter Do not rinse or wash the filter Continued gt 7 Eh Although not necessary the filter can be removed from the lid for cleaning Pull filter off lid and tap bottom of filter To replace firmly press filter onto lid until it stops Final filter Cleaning final filter The final filter assists in returning clean air to the room Remove dirt cup Press latch J and remove filter grid Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb HOOVER part No 27313107 Disconnect cleaner from electrical outlet Remove dirt cup as described in Fig 3 2 Insert a flat screwdriver into slot and remove the access door L 8 Replace lid and filter on filter chamber Place bottom of cup behind tab H and Replace chamber on dirt cup press cup into cleaner Rotate dirt cup handle E up to lock cup in place Lift out filter K and hand wash in cold water with a mild detergent Let filter air dry then reposition Replace filter grid and dirt cup Should you want to replace this filter ask for HOOVER part no 38766008 Do not operate cleaner without any of the filters in place Pull old bulb straight out of socket
4. e calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the com plete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner Hoover cleaning performance This Hoover Cleaning Performance Sys tem is for comparing the relative pro gressive performance of Hoover uprights only and not for comparison with any other brands The majority of this rating is based upon the ASTM International Carpet Cleaning Effective ness Test ASTM Test F608 Other per formance factors include Hose Power ASTM Test F558 Surface Litter Clean ing Hard Floor Cleaning Edge Clean ing Cleaning Width and Air Filtration you have a problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Problem Cleaner won t run Possible cause Possible solution Not firmly plugged in e Plug unit in firmly No voltage in wall plug e Check fuse or breaker Blown fuse or tripped breaker Replace
5. Appliances purchased elsewhere are covered by a limited two year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following Authorized Warranty Service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots For an automated referral of authorized service outlets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line at www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state or province If further assistance is needed or if there are questions concerning this warranty or the availability of warranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 13 14
6. Push new bulb straight into socket until locked in place Snap access door into place Reposition dirt cup Fig 3 10 Excessive force is not required Belt replacement The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the hood of the cleaner and should be checked from time to time to be sure it is in good con dition When to replace Disconnect cleaner from electrical outlet To check belt remove hood and agitator cover as shown in Figs 3 16 through 3 18 Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for HOOVER part No 40201190 How to replace Disconnect cleaner from electrical outlet With the handle in the upright position tilt cleaner back until it rests on floor Remove the 2 screws near the front of the brush roll cavity Press on handle release pedal M and lower the nozzle so it is flat Remove hose end Fig 2 11 Remove 2 screws at rear of hood Lift hood off cleaner With lettering to the outside of belt slide new belt along side of cleaner cavity and over motor pulley O Remove the 2 screws behind the agitator cover Remove agitator cover N Insert agitator through belt and place belt in belt guide P
7. continuing with each step until the blockage is found Turn cleaner OFF and disconnect from electrical outlet 1 Check fullness of dirt cup and filter assembly empty cup and clean filters if needed SUDULUI lo Check dirt path 2 Remove dirt cup look in duct A 3 Clear blockage from dirt duct Check intake opening 4 Remove dirt cup and look in duct B 5 Clear blockage from duct Check airflow path 6 Remove hose end from cleaner 7 Plug cleaner in and turn ON Check for suction at end of hose C a If there is suction continue with step 8 b If there is no suction check for blockage in hose Clear out hose Continued gt 11 4 4 ASA Q AL _Z ES gt RA N o Check hose inlet 8 Turn cleaner OFF and unplug 9 Remove hose end from cleaner 10 Press hose inlet door open and clear any blockages 12 Full Two Year any Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of two full years from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating condition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange
8. extra care when cleaning on stairs Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company others may cause hazards Save these instructions If you need any assistance Visit our website at www hoover com Click on the Service button to find the service outlet nearest you OR Call 1 800 944 9200 for an automated referral of service outlet locations U S only OR Call 1 330 499 9499 to speak with a representative in our Consumer Response Center Please do
9. fuse or reset breaker Thermal protector activated e Allow cleaner to cool for 30 minutes this will reset the thermal protector see pg 10 Problem Cleaner won t pick up Possible cause Possible solution Broken or worn belt Replace belt Agitator brush roll worn Replace brush roll Dirt cup full Empty cup Incorrect carpet height setting e Move nozzle control knob to lower setting Blockage in air flow passage e Clear blockage Pleated filter clogged e Clean pleated filter as described in the Filter assembly section Dirt cup not properly installed Position dirt cup properly and lock in place Fig 3 10 Filter chamber lid not positioned properly or missing e Ensure that filter chamber lid is proper ly positioned Filter assembly not installed properly e Ensure that the filter assembly is posi tioned properly Fig 3 9 Problem Cleaner hard to push Possible cause Possible solution Incorrect carpet height setting Move nozzle control knob to a higher setting Problem Cleaning tools won t pick up Possible cause Possible solution Dirt cup not properly installed Position dirt cup properly and lock in place Fig 3 10 e Blockage in hose e Clear blockage Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the fol lowing steps to check for blockages
10. not return this product to the store 1 Getting started Carton contents Your cleaner comes fully assembled with the tools and hose stored on B board d d Remove any tape or packing material from the cleaner lZ yO IM gt gt dl U N A Cleaner B Hose cleaning tools and wands packed on cleaner Packed inside extension wand Raise upper handle A to upright posi Press upper handle release button B Cord clip tion until it locks in place back to fold handle to storage position To help keep the cord out of the way while cleaning position cord into cord clip C Continued gt 3 Cleaner description lt gt SS CUZ F T MUN FATE CU qm x Operate cleaner only at voltage specified on data plate on bottom of cleaner This cleaner is intended for household use Polarized plug To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way ON OFF switch Plug cord into electrical outlet To turn cleaner ON push switch A toward front of cleaner To turn cleaner OFF push toward back of cleaner
11. 2 2003 The Hoover Company www hoover com tone U5465 900 120V 60Hz 1204 Y BELT 38528 033 LO USE ONLY e IGARENO SOLAMENTE POUR UN USAGE M NA3ER UNIQUEHENT nRT lt Carton Ohio 48720 LR baa y n UA Fabrique aux U Important Safeguards When using an electrical appliance always follow basic precautions including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE E m Wa rn n g m To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces e Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts Do not operate cleaner in bare feet or when wearing open toe shoes or sandals Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present Avoid picking up hard sharp objects with the cleaner They may damage the cleaner Always turn off this appliance before connecting or disconnecting hose Do not use without dirt cup or filters in place Empty dirt cup and clean filters fre quently when picking up very fine materials such as powder Use
12. HOOVERo __ TurboPOWER FoldAway Upright nk you for pi purchase gt E CC K s Review this manual before operating cleaner Thank you for choosing a HOOVER product Please enter the COMPLETE model and serial numbers in the spaces provided The numbers are located on the bottom of your cleaner Model Serial number Hint Attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Be sure to fill out and return the product registration card included with your cleaner see back cover Contents Getting Started 3 How to use 4 Cleaner Description 4 Cleaning Tools 6 If You Have a Problem 11 Clearing Blockages 11 12 Important Safeguards 2 Maintenance Authorized Service 11 Cleaning Filters 7 8 Emptying Dirt Cup 7 Lubrication 10 Replacing Agitator Brush Roll 10 Replacing Belt 9 10 Replacing Headlight 8 Thermal Protector 10 Warranty 1
13. and G Extension wand is used to give extra length to your hose Use it with any of the above tools Replacing hose When you are finished cleaning with the tools use the end of the hose to push the cover 1 down and push hose onto opening Twist hose end slightly to tighten the connector How to clean tools To clean the hose wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Remove hose When using cleaning tools cleaner handle should be in the upright posi tion Also turn cleaner OFF before disconnecting and connecting the hose H Remove hose end from cleaner base Extra reach hose The extra reach hose provides easier cleaning of stairs and hard to reach places Follow the steps below for attach ing and detaching hose Turn cleaner OFF before disconnecting and connecting hose Remove hose end from cleaner base Align end of extra reach hose with projec tions J with slots K on end of attached hose Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness Dirt cup The dirt cup assembly consists of the following parts Dirt cup A Filler chamber B Pleated filter C Lid D Dirt cup carry handle latch E Filter chamber release latch F While th
14. arpet and to prevent the cleaner from falling always place it at the bottom of the stairs Continued gt 5 Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when hanale is in upright position CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping clean er or setting it on furniture fringed area rugs or carpeted stairs during tool use Attach wand and tools The tools are attached to the hose or the wand in the same manner Push tool firmly onto hose twist tool slightly to tighten or loosen connection Attach second wand or tool to the wand in the same manner Slide hose into slots and twist hose to lock it into place To detach hose reverse procedure Attach wands or tools to the other end of hose 6 Select proper tool D Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers E Furniture nozzle may be used for upholstered furniture draperies mat tresses clothing automobile interiors and carpeted stairs F Crevice wand stores inside exten sion wand can be used in tight spaces corners and along edges in such places as dresser drawers upholstered furni ture stairs and baseboards It can also be used for extra reach with the dusting brush and or extension w
15. e cleaner is in operation the screen at the bottom of the filter chamber will stop larger debris from entering the pleated filter chamber This larger debris will be seen collectino in the the dirt cup The pleated filter will collect fine particles that have passed through the screen Filter assembly How to clean filter assembly Press latch F on front of filter chamber and remove lid The pleated filter is attached to the lid The screen I on the bottom of the chamber can be cleaned with a soft brush When to empty It is recommended that the dirt cup be emptied before the dirt reaches the dirt opening on back of dirt cup Fig 4 2 or after every use if preferred CAUTION Very fine materials such as face powder or cornstarch may seal the filter and cause loss of suc tion When using the cleaner for this type of dust empty the cup and clean the filters often How to empty Disconnect cleaner from electrical outlet Do not use the cleaner without dirt cup or filters in place Pull dirt cup handle E down Remove dirt cup Empty filter chamber Remove filter chamber B from dirt cup Holding the carry handle E empty dirt cup into wastebasket AN PEL Holding lid tap bottom of filter against edge of wastebasket until dust particles stop falling from filter
16. fe of the motor The addition of lubricant could cause damage Therefore do not add lubricant to motor bearings The agitator brush roll is equipped with two ball bearings that should be lubri cated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot Raise nozzle up and replace the 2 screws on the bottom Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and discon nect it from the electrical outlet 2 Check filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and the motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servicing see Service section Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot by e checking the Yellow Pages under Vacuum Cleaners Household OR e checking the list of Factory Service Centers provided with this cleaner OR echecking the Service section of The Hoover Company on line at www hoover com OR
17. urn the carpet height adjustment knob C to the desired setting For ease in turning the knob place handle in upright position and tilt cleaner back slightly Settings For maximum cleaning performance the following carpet height settings are recommended Low setting for all types of carpet and hard floors Note If the cleaner is difficult to push rotate knob to the next higher setting Medium and High settings for deeper pile carpet where easier pushing effort is desired while maintaining good cleaning performance Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only for ward strokes Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs With handle in operating posi tion place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper hanale As an alternative you may use the hose and furniture nozzle for stair cleaning Clean from bottom to top When using cleaning tools the agita tor will continue to rotate CAUTION To avoid personal injury or unnecessary wear to c
Download Pdf Manuals
Related Search