Snapper ZT18441KHC Lawn Mower User Manual
Contents
1. If Network Connection does not appear in the drop down list ActiveSync launched before your device had enough time to TIE recognize the card You must increase how long your device waits before auto launching ActiveSync For instructions please refer to the section on using the control panel applet at the end of this chapter 3 The mobile computer will start synchronizing The Connection Status screen will report when synchronization is done Connection Status Connected up to date Po Disconnect when complete 4 To stop ActiveSync tap on the Disconnect button You will still have network access but you will not be able to synchronize data 20 OPTIONAL Use the Control Panel Applet The control panel applet lets you control several unique features of Socket s enhanced Ethernet software including e Configuring the auto launch program e Viewing the IP info for your connection Start the Applet Launch the control panel applet by doing the following Pocket PCs Tap Start Settings Connections Socket 10 100 Handheld PCs Tap Start Settings Control Panel Socket 10 100 Pig Settings A PE TO 09 Bluetooth Connections Socket 10 100 Note If the Socket 10 100 icon does not appear soft reset your mobile computer by pressing the reset button CHAPTER 2 SETUP 21 Configure Auto Launch 2 22 Tap on the Auto Launch tab to specify what program to auto launch whenever you2. Follow these steps for software installation BEFORE inserting the 10 100 Ethernet CF Card 1 Use a serial Ethernet USB cable or cradle to connect your mobile computer to a host PC 2 In order to synchronize data there must be a partnership not a guest connection between the mobile computer and host PC e If you already established a partnership between the two computers they should automatically connect and begin synchronizing e If no partnership exists between the two computers a screen will appear asking if you would like to set one up Select Yes and click Next gt Follow the remaining screens on your host PC until the partnership has successfully been established New Partnership a y Set Up a Partnership Before you can synchronize information between your mobile device and this computer you must set up a partnership between them Would you like to set up 4 partnership Set up a partnership so that can synchronize information between my device and this computer No don t want to synchronize information Set up my device as a guest so that can copy or move information between my device and this computer Cancel Help IMPORTANT You must set up a partnership not a guest connection or you will not be able to synchronize data between your mobile computer and host PC 3 Insert the Socket 10 100 Ethernet Installation Disc into the host PC CHAPTER 2 SETUP 7 4 Use My Computer or Wind
3. Increase the second delay before launch setting in the Auto Launch tab of the 10 100 Ethernet CF Card Applet If you have to set the delay to longer than 20 seconds you should consult your network administrator Enter the IP address of the host computer in the Primary WINS field in order to use ActiveSync SYMPTOM My new IP addresses do not work POSSIBLE REASON SOLUTION After entering the IP addresses for your 10 100 Ethernet CF Card you forgot to tap click OK Re enter the IP addresses When done tap click OK SYMPTOM A message reports DHCP Lease Has Expired APPENDIX B TROUBLESHOOTING 25 POSSIBLE REASON SOLUTION You are using DHCP and have not Tap OK and continue used your 10 100 Ethernet CF Card for a while SYMPTOM My DHCP server keeps reporting that it is busy and cannot connect to my LAN POSSIBLE REASON SOLUTION Your network DHCP Server ran Inform your network out of IP addresses administrator SYMPTOM A message reports Error Starting Program Required dll File Not Found POSSIBLE REASONS SOLUTION You tried to install the software Make an active partnership without first establishing a between your device and a host PC Partnership or Guest relationship through the serial USB connection between your device and your host cable cradle Retry installing the PC software 26 Appendix C Technical Support If you have trouble installing or using the 10 100 Ethe
4. Interface Standards CompactFlash Interface With PC Card Adapter Operating System Support Windows Mobile 5 0 Windows Mobile 2003 2003SE Windows CE 3 0 Windows CE 2 11 Media Coupler Support Certification Compliance VCCI FCC CE C Tick CompactFlash Warranty 24 140 mA 80 mA CompactFlash I O Type I PCMCIA Type II Note Available separately at www socketcom com shop UTP RJ45 Class B Part 15 Class B EN55024 1998 s 182 Radio Communications Act 1992 CompactFlash Spec 2 0 Three years Appendix B Troubleshooting SYMPTOM Network Connection is not listed as an option in ActiveSync POSSIBLE REASONS SOLUTION Your device is using DHCP but it cannot access any IP addresses This may be because your device has problems communicating with your network s DHCP server or because your DHCP server is not available Your auto launch program starts too fast and your device does not have enough time to connect to your network Your server does not have WINS services enabled Try removing the 10 100 Ethernet CF Card and reinserting it If ActiveSync still shows no network connection wait for a few minutes If you see the message Unable to contact DHCP server using cached information the 10 100 Ethernet CF Card is probably working properly If after a few minutes the problem persists ask your network administrator to verify that the DHCP server is working properly
5. Socket Communications Incorporated Socket warrants this product against defects in material and workmanship under normal use and service for the following periods from the date of purchase Plug in Card Three years Incompatibility is not a defect covered by Socket s warranty During the warranty period Socket will at its option repair or replace the defective product at no charge when furnished with proof of retail purchase provided that you deliver the product to Socket or to an authorized Socket Service Center The returned product must be accompanied by a return material authorization RMA number issued by Socket or by Socket s Authorized Service Center If you ship the product you must use the original container or equivalent and you must pay the shipping charges to Socket Socket will pay shipping charges back to any location in the contiguous United States This warranty applies only to the original retail purchaser and is not transferable Socket may at its option replace or repair the product with new or reconditioned parts and the returned product becomes Socket s property Socket warrants the repaired or replaced products to be free from defects in material or workmanship for ninety 90 days after the return shipping date or for the duration of the original warranty period whichever is greater This warranty does not cover the replacement of products damaged by abuse accident misuse or misapplication nor as a res
6. Connections screen select Socket 10 100 Driver On a Pocket PC 2002 tap on the Properties button Network Adapters Adapters installed AsyncMaci NDISWAN Adapter ME2ZO00 Compatible Ethernet Driver PPTP1 NDISWAN Adapter SOCKET 10 100 Driver Socket LP E Driver Adapters such as wireless network Etherneti cards connect your mobile device to a network In the next screens enter your network settings SOCKET 10 100 Driver Use server assigned IP address Use specific IP address For DHCP select Use server assigned IP address Otherwise select Use specific IP address and enter the necessary information 12 If needed tap on the Name Servers tab to enter DNS and WINS addresses If using a static IP address you may need to enter the host computer s IP address in the WINS field to use ActiveSync SOCKET 10 100 Driver Name server addresses may be automatically assigned if DHCP is enabled on this adapter Fa H wins a Hl a 123 1 2 3 4 5 6 7 8 9 0 Tabjajwje r t yju ijojejt cAPja sjajfjulhjijkji Shift z x c Y bjnjm Z ce ee E Ej When done tap ok IMPORTANT If you forget to tap ok your settings will not take effect 4 Soft reset your Pocket PC by pressing the reset button CHAPTER 2 SETUP 13 Handheld PC Pros Handheld PC 2000s and Pen Tablets 1 Go to Start Settings Control Panel Network 2 Inthe next screen select Socket 10
7. can set your mobile computer to 10 100 automatically launch ActiveSync or any other program whenever you insert the card minimizing the time and effort to connect You also have instant access to key network settings Software updates www socketcom com product ethernet_10100 asp System Requirements Your mobile computer should meet these minimum requirements e Any of the following operating systems Windows Mobile 5 0 Windows Mobile 2003 2003SE Windows CE v2 11 or later e Available CompactFlash or PC Card slot that supports CF I O CompactFlash to PC Card adapter required if using a PC Card slot e During installation you will need a desktop or laptop computer that meets these minimum requirements Windows 98SE Me 2000 or XP Microsoft ActiveSync Windows Mobile 5 0 devices require ActiveSync 4 0 or greater ActiveSync 4 0 does not support synchronization over Ethernet Because Windows Mobile 5 0 devices require ActiveSync 4 0 these devices cannot synchronize over Ethernet Devices running a previous version of Windows Mobile can synchronize over Ethernet using a previous version of ActiveSync 2 For some HPC Pros the CompactFlash slot only supports memory I O and is not compatible with the 10 100 Ethernet CF TIP Card only the PC Card slot supports CF I O If you have one of these computers use a CF to PC Card adapter to insert the card into the PC Card slot WARNING AN If you are NOT us
8. your network card coor C networietard a Adyanced CHAPTER 2 SETUP 2 The Configure Network Adapters screen will appear In the drop down menu at the top of the screen select the appropriate option e The Internet For connecting from home and or via an ISP e Work For connecting to a private network such as at work or a proxy network SOCKET 10 100 Driver Socket LP E Driver Socket WLAN SDIO V2 Driver NE2ZO00 Compatible Ethernet Driver L2TP NDISWAN Miniport Asvnchlac NOTSY ARN Miniport PPTP NDISWAN Miniport a Note If you are connecting to a proxy or secure network refer to your Pocket PC documentation for configuration information 3 If you DO NOT need to enter any IP addresses 1 e your network uses DHCP tap ok You are now ready to proceed to STEP 4 to insert the card and connect to a network 4 If you DO need to enter any IP addresses tap Socket 10 100 Driver 5 In the next screens enter your network settings from the Network Information Form Select Use specific IP address to enter any necessary IP addresses 4 Settings a a27 G SOCKET 10 100 Driver D Use server assigned IP address Use specific IP address al 2 31415 6 7 8 90 rablalwle r tly uli olelT T caPla s lal tlalnla felts snitt z x e v b n m 7 cual AT iee 10 If needed tap on the Name Servers tab to enter DNS and WINS addresses d aze GD SOCKET 10 100 Driver Name server addr
9. 10 100 Ethernet CF Card CompactFlash and PC Card solutions for Pocket PCs Handheld PCs and pen tablets running Windows Mobile 5 0 Windows Mobile 2003 2003SE Windows CE 2 11 or 3 0 User s Guide 10 100 ETHERNET CARD socket a socket a Increasing Mobile Productivity 8 2005 Document 6410 00169 G Copyright Notice Copyright 2005 Socket Communications Inc All rights reserved The 10 100 Ethernet CF Card includes technology licensed under United States Patent Nos 4 543 450 4 603 320 4 686 506 and 4 972 470 Socket and the Socket logo are registered trademarks of Socket Communications Inc Socket Communications Socket 10 100 Ethernet CF Card and Mobility Friendly are trademarks of Socket Communications Inc All other brand and product names are trademarks of their respective holders Reproduction of the contents of this manual without the permission of Socket Communications is expressly prohibited Please be aware that the products described in this manual may change without notice Feel free to contact Socket Communications at Socket Communications Inc 37400 Central Court Newark CA 94560 Other than the above Socket Communications can assume no responsibility for anything resulting from the application of information contained in this manual Socket Communications requests that you refrain from any applications of the Socket 10 100 Ethernet CF Card that are not described in this ma
10. 100 Ethernet Driver Tap Properties Network Configuration fa ok x NE2000 Compatible Ethernet Driver PROXIM Ethemet Driver 3 The IP Address screen will appear Following your completed Network Information Form enter the appropriate settings for your network SOCKET 10 100 Ethernet Driver Settings IP Address Name Servers An IP address can be Dita an IP address via BHP to this computer If your network Specify an IP address Soak okay e aki E IP addresses ask your network administrator for an address set Mik and then type it in the space nee Mas provided Default Gateway CET 4 If needed click on the Name Servers tab to enter any necessary DNS or WINS addresses SOCKET 10 100 Ethernet Driver Settings Note If using a static IP address you may need to enter the host computer s IP address in the Primary WINS field to use ActiveSync 5 When done entering all your network settings tap OK IMPORTANT Your new settings will not take effect if you forget to tap OK 14 STEP 4 Insert Card and Connect to LAN 1 If you have not done so already soft reset your mobile computer Do not soft reset a Pocket PC 2003 when a Socket AN card is inserted Wait for the device reset to finish before you insert the card 2 Insert the 10 100 Ethernet CF Card into your mobile computer Make sure the card is right side up Use a PC Card adapter to insert the card into a PC Card
11. LE OUTSIDE OF THE UNITED STATES OF AMERICA NO OTHER WARRANTIES SOCKET disclaims all other warranties either express or implied including but not limited to implied warranties of merchantability and fitness for a particular purpose with respect to the SOFTWARE and the accompanying written materials This limited warranty gives you specific legal rights You may have others which vary from state to state NO LIABILITY FOR CONSEQUENTIAL DAMAGES In no event shall SOCKET or its suppliers be liable for any damages whatsoever including without limitation damages for loss of business profits business interruption loss of business information or other pecuniary loss arising out of the use of or inability to use the SOFTWARE even if SOCKET has been advised of the possibility of such damages Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages the above limitation may not apply to you EXPORT LAW ASSURANCES You may not use or otherwise export or reexport the SOFTWARE except as authorized by United States law and laws of the jurisdiction in which the SOFTWARE was obtained In particular but without limitation none of the SOFTWARE may be used or otherwise exported or reexported a into or to a national or resident of a United States embargoed country or b to anyone on the U S Treasury Department s list of Specially Designated Nationals or the U S Department of Commerce s Ta
12. be required to correct the interference at his or her own expense If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user may try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna of the radio or television e Increase the distance separating the equipment and the receiver e Connect the equipment to an outlet on a different branch circuit than that of the receiver e Consult the dealer or an experienced radio TV technician for help The user may find the following booklet helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Product Disposal Your device should not be placed in municipal waste Please check X local regulations for disposal of electronic products 7 30 Socket Communications Inc 8 2005 Printed in U S A
13. ble of Denial Orders By using the SOFTWARE you represent and warrant that you are not located in under control of or a national or resident of any such country or on any such list GOVERNMENT END USERS If the SOFTWARE is supplied to the U S Government the SOFTWARE is classified as restricted computer software as defined in clause 52 227 19 of the FAR The U S Government s rights to the SOFTWARE are as provided in clause 52 227 19 of the FAR CONTROLLING LAW AND SEVERABILITY This License shall be governed by the laws of the United States and the State of California If for any reason a court of competent jurisdiction finds any provision or portion thereof to be unenforceable the remainder of this License shall continue in full force and effect 29 Regulatory Compliance This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules This equipment is also CE EN55024 1998 and C TICK compliant These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
14. e 10 100 Ethernet CF Card on a Pocket PCs Handheld PCs and pen tablets running Windows Mobile 5 0 Windows Mobile 2003 2003SE Windows CE 2 11 or 3 0 ee go Ee F irere of tipi aaa Scirocco cee socket r jae fa ee Haks aha siiri Oe a b E f ie ap pene be Setup Summary STEP 1 Prepare network information STEP 2 Install the software STEP 3 Enter network settings STEP 4 Insert card and connect to LAN port OPTIONAL Use ActiveSync over a Network OPTIONAL Use the Control Panel Applet STEP 1 Prepare Network Information Contact your network administrator for the network settings A text only form that you can email to your network administrator is available in the Docs folder in the installation CD and online at www socketcom com support support_ethernet asp Does the network support DHCP Dynamic Host Configuration Protocol _ YES If Yes then what is the valid range of IP addresses for your network L_ NO If No then please any of the following IP addresses required by your network you may need only some a Mobile Computer IP address b Subnet Mask c Default Gateway x d Primary DNS we e Secondary DNS ______ f Primary WINS ww g Secondary WINS ___ CHAPTER 2 SETUP 5 Remote ActiveSync only If your server does NOT have WINS services enabled use the IP address of your host PC instead of a Primary WINS address STEP 2 Install the Software
15. esses may be automatically Note If using a Static IP assigned if DHCP is enabled on this adapter address you may need to enter Le r a the host computer s IP address in the WINS field to use wins _ oo ActiveSync atwns o o 123 1 2 3 4 5 6 7 8 9 0 Tabla wie r tiy uliljo p tid CaPials d fia hiiiki i s Shift z x c Y bjnjm Z cuja X te gt Ej 6 When you have finished entering settings tap ok IMPORTANT If you forget to tap ok your settings will not take effect 7 A screen will report that the new settings will take effect when you next insert the network card Tap ok i Settings ay a2 3 54 Configure Network Adapters ie ok The new settings will be applied the next time the adapter is used If the adapter is currently in the device remove and re insert the adapter to apply the settings AsyocMac NDISWAN Miniport L2TP NDISWAN Miniport 8 Soft reset your Pocket PC by pressing the reset button ma Do not soft reset a Pocket PC 2003 when a Socket card is i inserted or errors may occur in application s using the card TIP If errors occur remove the card and soft reset the device Wait for the device reset to finish before you re insert the card CHAPTER 2 SETUP 11 l 3 Pocket PC 2000 2002 Pocket PC 2000 Go to Start Settings Connections Network Pocket PC 2002 Go to Start Settings Connections Network Adapters In the Network
16. he valid range for your network d Test you web access Start Pocket Internet Explorer Enter a URL and test to see if it appears correctly If you cannot enter a URL because the address bar does not appear tap View Address Bar Windows Mobile 2003 When turning your device ON or OFF ots resume suspend with the 10 100 Ethernet card in the CF slot TIP wait a minimum of three 3 seconds before cycling the power state OFF ON Changing the power state more quickly than this may result in a failed network connection If a connection is not established remove and reinsert the card CHAPTER 2 SETUP 17 OPTIONAL Use ActiveSync over a Network IMPORTANT ActiveSync 4 0 does not allow synchronization over Ethernet Make sure you are using a previous version of ActiveSync Windows Mobile 5 0 devices which require ActiveSync 4 0 cannot perform this procedure Pocket PC 2003 2003SE 2 3 18 1 Tap Start ActiveSync Not Connected Note In order to use ActiveSync you must have previously created a Synchronize with Windows PC partnership not pict Last Sync 6 12 03 4 03 PM connection between the device and host PC Tap Tools Options In the next screen check Sync with this PC during manual sync Tap ok tep ER ull bee ActiveSync E di5 PC Synchronization When syncing remotely with a PC Use this PC ELIZABETH _ Use mobile schedule to syne with this PC Syne with this PC during manual s
17. ing Windows Mobile 5 0 DO NOT install ActiveSync 4 0 or you will not be able to synchronize your mobile computer and host PC over an Ethernet connection Microsoft removed this feature from ActiveSync 4 0 If your Windows version does not require ActiveSync 4 0 then Socket recommends that you use an older version of ActiveSync that supports device synchronization over Ethernet Package Contents The 10 100 Ethernet CF Card package includes these items e A Socket 10 100 Ethernet CF Card CompactFlash Type I e The 70 100 Ethernet Installation Disc e Booklet containing copyright and warranty information CompactFlash to PC Card adapters are available separately online qip from Socket at www socketcom com shop CHAPTER 1 INTRODUCTION 3 Product Registration Socket highly recommends that all customers register their Socket products Registered users receive priority for technical support product updates and special offers Register your card online at www socketcom com prodreg Product Registration Technical Support I am a new user I am a returning user Please select your Country or Region Welcome back Please sign in Email Address Country Region Select a Country Password Fegan Forget Password Product registration is not required to ensure your warranty rights gt Please contact webmaster socketcom com if you need help This chapter explains how to set up and use th
18. insert the 10 100 Ethernet CF Card Use the drop list to select a program to auto launch if desired i Settings e qgar Socket 10 100 Settings Choose a program to run when the Socket 10 100 Ethernet card is inserted lt do not run 4 program gt Program arguments 10 gg second delay before launch For more configuration items go to Network settings You can use the Program arguments field for custom applications that require program arguments to launch The second delay before launch field lets you choose how long your mobile computer will wait before auto launching a program Most devices have a default of 10 seconds Unless your network is slow or if memory is low 10 seconds should be long enough to recognize the 10 100 Ethernet CF Card View IP Info Tap on the IP Info tab at the bottom of the screen to view your network s IP addresses You can also see if your address 1s static or assigned by DHCP ae Settings f i Socket 10 100 Settings set Mosk peat Gateway ons oo vac adress The IP Address is assigned by DHCP You cannot modify any of the settings CHAPTER 2 SETUP You can only use the IP Info screen to view network information 23 Appendix A Specifications Physical Characteristics CompactFlash Card Dimensions Mass 3 44 x 1 69 x 0 13 in 88 x 42 8 x 3 3 mm 30 g Power Consumption supplied by PC host Typical at 100 Mbps Typical at 10 Mbps
19. nual Socket Communications also requests that you refrain from disassembling the CompactFlash Card Disassembly of this device will void the product warranty You can track new product releases software updates and technical bulletins by visiting Socket s website at www socketcom com Table of Contents Copyright Notice 1 INTRODUCTION About the Software System Requirements Package Contents Product Registration 2 SETUP STEP 1 Prepare Network Information STEP 2 Install the Software STEP 3 Enter Network Settings STEP 4 Insert Card and Connect to LAN Status Indicator LEDs OPTIONAL Use ActiveSync over a Network OPTIONAL Use the Control Panel Applet APPENDICES A SPECIFICATIONS B TROUBLESHOOTING C TECHNICAL SUPPORT Limited Warranty Monn oid BRWPYPNYMDND N _ 24 25 27 28 1 Introduction Would you like to ActiveSync your mobile computer in the fastest and most convenient way possible Do you need to back up or restore files in a flash Then you need Socket s 10 100 Ethernet CF Card It s the best solution for accessing hi speed networks running up to 100 Mbps The sleek design integrates a Type I CompactFlash card and network connector into one durable unit It is among the lowest in its class in power consumption About the Software Socket s enhanced drivers for Windows Mobile help you save time and effort with special auto launch and network pee monitoring features You
20. ows Explorer to access the CD drive In the CD click on SETUP EXE setup Setup exe _ CD Drive La InstallShield Software Corpora 5 The installation wizard should begin Follow the instructions on your host PC and mobile computer until installation is complete Socket 10 100 Ethernet Utilities InstallShield Wizard Welcome to the InstallShield Wizard for Socket 10 100 Ethernet Utilities The InstallShield Wizard will install Socket 10 100 Ethernet Utilities on your computer To continue click Nest cE 6 After completing the installation disconnect the mobile computer from the cable cradle Soft reset the mobile computer by pushing the reset button IMPORTANT Soft reset your mobile computer after software installation STEP 3 Enter Network Settings Windows Mobile 2003 2003SE and Windows Mobile 5 0 1 Open the Configure Network Adapters screen Windows Mobile 5 0 Tap Start Settings Connections tab Network Cards i _ Settings qm q 11 38 X 3 Q ih Beam Bluetooth Windows Mobile 2003 2003 SE Tap Start Settings Connections Connections Tap on the Advanced tab Tap on the Network Card button at the bottom of the screen ehg a7 G Connections Networks are groups of settings used by programs to automatically connect to an ISP or private network Select Networks Dialing rules determine how a number is dialed From a specific location Select Location Select what
21. rnet CF Card contact Socket s technical support department for assistance IMPORTANT To obtain technical support you must first register your product online at www socketcom com prodreg After you register your product and log in click on the Technical Support tab then click New Trouble Ticket to submit an online request for technical support Afterwards you can log in anytime to monitor the status of your request If we cannot resolve your inquiry online we can arrange for a support engineer to call you at a specific time T Personal Profile X Register Product s Technical Support Offers Updates Loc our E Your list of Technical History is below Please click on your Ticket ID to gt view or reply to our Technical Support You can also create a new BZ New Trouble Ticket Trouble Ticket to the right Allow up to 48 hours for a response r technical history Ticket ID Email Sent Responded Product Technical Support has not viewed your inquiry Technical Support is working on your inquiry Technical Support is escalating your problem Please allow some time for a reply bl New message from Socket Technical Support A Old message waiting for your reply 8 Ticket ID Closed Automatically close after 7 days of no activities Please refrain from disassembling the CompactFlash Card Disassembly of this device will void the product warranty APPENDIX C TECHNICAL SUPPORT 2 Limited Warranty
22. slot 3 Plug a cable from your LAN into the connector at the top of the card 4 LEDs on the card should turn on and or blink depending on the connection status Status Indicator LEDs LED LED Activity Meaning Link Solid Green Good Link 100 Solid Orange 100 Mbps mode T Blinking Green Activity hvs kes Solid Orange Collision CHAPTER 2 SETUP 15 5 If you would like to check if you have a good connection do the following a When ActiveSync automatically launches close the program Tap the button in the upper right corner Be ActiveSync ee 2 4 07 X Mot Connected Synchronize with Windows PC Last Sync 6f 12 03 4 03 PM b Check to see if the Link Status LED H has a steady green light to denote a good connection If the Activity Status LED al 1S blinking your device is communicating with your network c Verify that the connection has a valid IP address for your network e Open the Socket 10 100 applet Pocket PC Tap Start Settings Connections Socket 10 100 HPC Tap Start Settings Control Panel Socket 10 100 Socket e Inthe IP Info screen check the IP Address field aF Settings 11 03 old Socket 10 100 Settings P Address E subnet masi E Default Gateway a The IP Address is assigned by DHCP If your network uses a static IP address make sure it appears correctly 16 If your network uses DHCP make sure the IP address is within t
23. ult of service or modification other than by Socket SOCKET IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY INCLUDING DAMAGE TO PROPERTY AND TO THE EXTENT PERMITTED BY LAW DAMAGES FOR PERSONAL INJURY THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not allow limitation of implied warranties or the exclusion or limitation of incidental or consequential damages so that the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state This product may contain fully tested recycled parts warranted as if new For warranty information please call 510 744 2700 28 Limited Software Warranty LIMITED WARRANTY SOCKET warrants that the original disk or CD ROM is free from defects for 90 days from the date of delivery of the SOFTWARE CUSTOMER REMEDIES SOCKET S entire liability and your exclusive remedy shall be at SOCKET S option either a return of the price paid or b replacement of the SOFTWARE which does not meet SOCKET S Limited Warranty and which is returned to SOCKET with a copy of your receipt Any replacement SOFTWARE will be warranted for the remainder of the original warranty period or 30 days whichever is longer THESE REMEDIES ARE NOT AVAILAB
24. ync In the main ActiveSync screen tap Sync The Pocket PC will begin to synchronize data with your host PC To stop ActiveSync tap Stop You will still have network access but you will not be able to synchronize data between your Pocket PC and host PC Pocket PC 2002 1 Tap Start ActiveSync Not Connected Note In order to use ActiveSync you must have previously created a partnership not a guest PA N connection between the device and host PC 2 Tap on Sync The Pocket PC will begin to synchronize data with your host PC Synchronize with PC Last Sync O6f12 2002 10 51 AM lE If ActiveSync starts and stops go to Tools Options Mobile q p Schedule and uncheck the Sync outgoing items as they are sent box 3 To stop ActiveSync tap on Stop You will still have network access but you will not be able to synchronize data between your mobile computer and host PC CHAPTER 2 SETUP 19 Pocket PC 2000 or Handheld PC 1 Pocket PC 2000 Tap Start Programs Connections ActiveSync HPC Tap Start Programs Communication ActiveSync ActiveSync Choose a method to connect to the Important selected desktop computer You must have a partnership with a Connect to JERR Y2 host PC to use ActiveSync Network Connection ha 2 Select Network Connection in the top drop down list Choose the desktop computer you want to connect to in the bottom drop down list then tap Connect
Download Pdf Manuals
Related Search