Simplicity 1694498 Printer User Manual
Contents
1. 7 Figure 9 Install Idler Assembly A Idler Assembly D Locknuts 5 16 18 Figure 10 Install Turbo Drive Pulley tn 5 16 18 x 7 8 Ee tap ME Ci A Original Pulley amp Spacer D Spring Washer B Spacer W Groove New E Sleeve Nut Install Idler Assembly amp Belt Cover C Pulley New F Spacer New 1 See Figure 9 Remove and discard the two taptite screws from locations E 2 Insert two 5 16 18 x 7 8 capscrews C through the mower deck and arbor Tighten the capscrews 3 Mount the idler pulley assembly A to the deck using the two 5 16 18x 7 8 capscrews C and 5 16 18 whi zlock nuts D Install Turbo Drive Pulley 1 See Figure 10 Remove the arbor drive belt from the right side arbor pulley 2 Remove and discard the flange nut and spring wash ers securing the arbor pulley and spacer A Retain the pulley and spacer A 3 Install the new spacers B amp F turbo drive pulley C spring washer D and sleeve nut E Be sure the notches in the pulleys and spacers are aligned Install the spring washer concave side down Torque Figure 11 Anchor Bracket Assembly the sleeve nut to 55 70 ft Ibs 74 95 N m A Anchor Bracket E Nut Hex 5 16 4 Reinstall the arbor drive belt on the lower pulley B Lockwasher 5 16 Large F Wing Nut 5 16 C Latch Spring G Locknut 5 16 D Lockwasher 5 16 Small H Capscrew 5 16 18 x 2 1 2 Install Anchor Bracket 1 See Figure 12 If not already2. be plugged or the bags may be full discontinue mowing stop the unit disengage the PTO shut off the engine and then empty the catcher or clear the tube WARNING ALWAYS shut off the tractor Disengage the PTO and allow all moving parts to stop BEFORE disconnecting or clearing tube or emptying catcher Before leaving the operator s position for any reason engage the parking brake disengage the PTO stop the engine and remove the key To reduce fire hazard keep the engine rider and mower free of grass leaves and excess grease Do not stop or park rider over dry leaves grass or combustible materials CAUTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet as well as the Operator s Manual for the tractor and any other attachments General Onerating Instructions BEFORE OPERATION Clear the lawn of all sticks stones wire and other debris which may be caught or thrown by tne mower blades Check grass condition If wet wait until later in the day If grass is wet the grass catcher is likely to become plugged For efficient bagging air circulation under the mower deck through the chute and into the bag is very important For this reason BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris Make sure th
3. for flange whizlock nuts and screws use 135 of grade 5 torgues N Unless otherwise noted on assembly drawings all torque values must meet this specification A Wrench amp Fastener Size Guide 1 4 Bolt or Nut Wrench 7 16 5 16 Bolt or Nut Wrench 1 2 3 8 Bolt or Nut Wrench 9 16 16 7 16 Bolt or Nut 1 2 Bolt or Wrench Bolt 5 8 Wrench Nut 11 16 Nut Wrench 3 4
4. loss of control of gle A in text signifies important cautions or warnings which must be followed GENERAL WARNINGS e Know the units controls and how to stop quickly READ THE OPERATOR S MANUALS Read and obey all safety decals Only allow responsible adults who are familiar with the instructions to operate the unit Disengage the PTO Shut off the engine and wait for all moving parts to stop before attaching adjusting or disconnecting any part of the collection system Check the collection system to make sure it is bolted tightly to the unit DO NOT operate the unit without either the entire grass catcher or the deflector in place Turn off the PTO to disengage the blades when not mowing DO NOT mow in reverse Always look down and behind before and while travelling in reverse DO NOT turn sharply when travelling alongside a building or any object Slow down before turning DO NOT carry passengers When collection system is removed from the mower deck the deflector must be properly installed Collector bags are subject to deterioration and wear during normal use Inspect the bag periodically for tears holes or weak spots and replace with a new bag that meets manufacturer s durability standards SAFETY DECALS This unit has been designed and manufactured to pro vide you with the safety and reliability you would expect from an industry leader in outdoor power eguipment manufacturing Although reading this manu
5. never across the face of any slope e When operating on slopes use front counter weights Never operate on slopes greater than 17 6 10 These labels are easily applied and will act as a constant visual reminder to you and others who may use the equipment to follow the safety instructions necessary for safe effective operation ATTACHMENT DECALS e This shield must be in place at all times during operation e Do not open cover with engine running 9 e Do not operate mower without the complete catcher in place e When operating on slopes refer to operator s manual for counterweights e Mower deflector must be in down position when blower is removed 1 Decal WARNING Do Not Open Cover Part Number 1704405 Decal WARNING Part Number 1717291 Read and obey all operation and warning decals x O PR A IA ZA K Va FLLI SRI RE R eee Le KY DO X OM eee MOWING WITH THE CATCHER Always operate with throttle at full speed when mowing Grass should be cut often and not too short If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging If grass is long operate with mower in high cutting position for first pass cutting again in a lower position on a second pass Do not open the cover with mower engaged If a large amount of cut grass is spilling out from under deck the tube may
6. 1 from trunnion B Remove trunnion B from rear deck lift lever A Mark or measure trunnion position on rear deck lift lever Remove trunnion B from from eyebolt I Remove capscrew K washer J eyebolt I spacer H and nut L from mower deck M 3 Thread eyebolt 1 through plate G as shown 4 Attach capscrew K washer J eyebolt I spacer H to mower deck M securing with nut L Slide washer F spring E and spacer D onto eyebolt I as shown Install trunnion B onto eyebolt I to position of mea surement or mark from step 1 Install trunnion B into rear deck lift lever A secure with hair pin C Check deck leveling as described in Operators Manual and make necessary adjustments Front Weight Carrier Installation 1 Remove and discard hardware from holes G Figure 2 Install carrier F as shown securing with 5 16 18 cap screws B 5 16 washers A and 5 16 locknuts C Rod D and safety clip E are used to secure required weights Rear Deck Lift Lever Trunnion Existing Hair Pin Existing Spacer Spring New Spring New Washer New Plate Spring Support New Spacer Existing Eyebolt Existing Washer Existing Capscrew Existing Nut Existing Mower Deck SCFAC ITOMNMOIOOWDSD ae Figure 2 Front Weight Carrier Installation A Washer 5 16 B Capscrew 5 16 18 x 1 C
7. How to use this file Operators Manuals Instructions for Print Vendors Paper Manuals Paper Size 11x17 Body 50 lbs brilliant white offset or equivalent Gover on pre printed two tone Swash stock Press Body 1 color 2 sided Cover imprint 1 color 1 sided Bindery Saddle Stitch Face Trim Face Trim COVERS This file may contain several manuals which differ only in their covers Govers are all present at the beginning of this file Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover e Check the front cover for the individual part number typically a 171xxxx number BODY e The body of the manual is identical regardless of the cover used REMEMBER ODD number pages are ALWAYS right hand pages and EVEN number are ALWAYS left hand pages General This instruction page is NOT part of the manual and must NOT be printed e Pages labeled with the text THIS PAGE INTENTIONALLY BLANK are placement pages ONLY and should NOT be printed THIS PAGE INTENTIONALLY BLANK Simplicity SNAPPER ATTACHMENT OPERATOR S MANUAL ime 5 OE o Clean Sweep Twin Catcher fg No Description 1726793 Simplicity MANUFACTURING INC 500 N Spring Street PO Box 997 Port Washington WI 53074 0997 www simplicitymfg com Copyright 2004 Simplicity Manufacturing Inc All Rights Reserved Printed in USA Safety R
8. Locknut 5 16 18 D Rod E Clips Safety F Carrier Weight G Holes Initial Hitch amp Tube Installation 7 gt v s M O NY JA R S 7 y A y Figure 1 Install Hitch Plate A Hitch Plate E Upper amp Lower B Heat Shield Bumper C Capscrews F Washer Figure 2 Install Hitch Assembly 1 2 13 x 1 1 4 G New Holes 17 32 A Horizontal Support C Nut 3 8 16 D Locknuts 1 2 13 H Existing RH Holes B Capscrew 3 8 16 x 3 4 D Back Plate HITCH amp TUBE INSTALLATION Install Hitch Plate and Back Plate 1 Remove and discard right side hardware holding heat shield B Figure 1 to upper and lower bumper E to existing right hand holes H 2 Enlarge upper existing hole H to 17 32 Install hitch plate A to upper and lower bumper E and heat shield B using upper existing hole H and one 1 2 13 x 1 1 4 capscrew and 1 2 13 nut 3 Square hitch plate A Figure 1 to upper amp lower bumper E and use as a template to mark and drill three new holes 17 32 G 4 Secure hitch plate A Figure 1 to upper amp lower bumper E with 1 2 13 x 1 1 4 capscrews C washer F and 1 2 13 locknuts D as shown 5 Install the horizontal support A Figure 2 on the back plate D Secure with four 3 8 16 x 3 4 cap screws B 3 8 16 locknuts C Figure 3 Install Back Plate 6 Set the back plate and support A Figure 3 onto pinS A Back Plate an
9. Sizing Hardware Grade SAE Grade 5 SAE Grade 8 SAE Grade 2 Hex Nut Size Of in bs in Ibs in Ibs Hardware ft Ibs Nm ft lbs Nm ft Ibs When a washer or nut is identified as 1 2 this is the 8 32 4 6 Nominal size meaning the inside diameter is 1 2 inch if a 8 36 4 9 second number is present it represent the threads per inch 10 24 6 8 10 32 l 7 1 1 4 20 l 16 3 1 4 28 19 0 5 16 18 34 0 When bolt or capscrew is identified as 1 2 16 x 2 this means the Nominal size or body diameter is 1 2 inch the second number represents the threads per inch 16 in this example and the final number is the body length of the bolt or screw in this example 2 inches long 5 16 24 34 0 The guides and ruler furnished below are designed to nay la help you select the appropriate hardware and tools 3 8 68 0 7 16 14 95 2 S 6 20 108 8 s Nut 1 2 1 2 13 149 6 R JON 1 2 20 163 2 N AD D DE zis 4 LS 9 16 18 231 2 A 9 0 11 299 2 j lt 5 8 18 326 4 3 4 10 525 0 A 3 4 16 571 2 N 118 9 816 0 Screw 1 2 x 2 7 8 14 897 6 1 8 1 244 0 N Body 1 12 1 360 0 a Diameter NOTES A Body These torque values are to be used for all hardware N Len excluding locknuts self tapping screws thread forming gth screws sheet metal screws and socket head setscrews A Recommended seating torque values for locknuts W a for prevailing torque locknuts use 65 of grade 5 torques N b
10. al and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effec tively we have placed several safety labels on the unit to remind you of this important information while you are operating your unit All DANGER WARNING CAUTION and instructional messages on your rider attachments and mower should be carefully read and obeyed Personal bodily injury can result when these instructions are not followed The information is for your safety and it is important The safety decals below are on your product lf any decals are lost or damaged replace them at once See your local dealer for replacements TP 600 2562 01 AT SMA e If the mower stalls or the collector chute plugs 1 Disengage the PTO 2 Stop the engine and remove the key 3 Set the parking brake and wait for all moving parts to stop 4 Remove the foreign object or clear the chute with a piece of wood before restarting the engine NEVER place hands into COLLECTOR OR MOWER housing to clear jammed objects Blower OR MOWER may rotate when object is removed e For added stability and to prevent tipping or loss of control a Use reduced speed on uneven ground and when turning corners b Reduce loads on hillsides It is recommended that the collection system be kept only half full when negotiating any slopes Start mowing on slopes when the collection system is empty c Mow up and down the face of slopes
11. and Bags 1 Hang the bags F Figure 7 on the horizontal sup port Note If desired the bags can be lined with 30 gallon trash bags for easy disposal 2 Install the handle B inside the cover Secure with two 10 32 x 1 2 screws C and nuts A 3 Rest the cover assembly D on the bags F 4 Install the two hinge pins E and secure with hair pin clips G 5 Open the cover and fasten cable A Figure 8 to sup port B The looped cable end fits over washer C NOTE Push the hair pin clips all the way on or they will be bent by the hinge when the cover is opened Figure 7 Install Catcher A Nut 10 32 E Hinge Pin B Handle F Bags C Screw 10 32 x 1 2 G Hair Pin Clip D Cover Figure 8 Install Cable A Cable C Washer B Support 13 Normal Removal amp Installation Tubes Hair Pin Clip Bags Clevis Pin Cover Clip 7 MOQOW gt Figure 9 Normal Removal amp Installation WARNING OPERATION WITHOUT TURBO amp CATCHER For operation without turbo the mower deflector MUST be properly installed in the down position and retained by the spring latch See Turbo Operator s Manual NORMAL REMOVAL amp INSTALLATION Removing the Grass Catcher 1 Disconnect the tubes A Figure 9 from the turbo and remove them from the catcher 2 Remove the hair pin clip B Figure 9 and clevis pin D securing the cover E Disconnect the cable see Fi
12. at there is a snug fit between mower deck blower housing tubes and grass catcher cover REGUIRED ACCESSORIES A front mounted factory approved weight carrier and 66 los worth of weights are required when using this rear mounted grass catcher Never operate on slopes greater than 17 6 10 AFTER OPERATION CAUTION Do not leave grass in bagger containers Empty containers after each use and before storing Failure to do so may result in spontaneous combustion which could develop into a fire Remove any debris from the the screen on the underside of the lid Note The lid screen can be partially removed for easier cleaning and should be cleaned regularly The blower housing and tube should be removed for cleaning Inspect the grass bags for wear or damage Make sure that there is a snug fit between mower deck blower housing tubes and grass catcher cover STORING THE GRASS CATCHER Clean the grass catcher thoroughly using a mild deter gent other products may damage the tube Remove any debris from the the screen on the underside of the lid If paint has been scratched on metal parts touch up with paint or apply a thin film of oil to prevent corrosion Store in a dry area Dry thoroughly before storing for a long period of time Always store away from moisture initial Turbo installation 49 35 Setup Torque to 55 70 ft Ibs A b 25 By 29 Existing Pulley 8 Spacer Ex
13. cover support A with a 5 16 18 x 1 capscrew B 5 16 18 x 1 Capscrew Carriage Bolt 9 16 washer G and flange whizlock nut C 5 16 18 Whizlock Nuts G 5 16 Washer Deflector Support Rod Pivot Bracket moov Initial Turbo Installation Install Deflector 1 See Figure 6 Drill four 13 64 holes from the bottom of the deflector at the pre molded drill points A bot tom of deflector 2 Attach the deflector to the support rod wire form using four 10 14 x 3 4 truss head screws and nylock nuts Figure 6 Install Deflector A 13 64 Hole Locations C Screws 10 24 x 3 4 B Nylock Nuts Install Belt Guide 1 See Figure 7 8 8 Locate the taptite screw that will be replaced by capscrew C Remove and discard the taptite screw 2 Assemble the 5 16 18 x 1 1 2 capscrew C lock washer E washers B belt stop D and spacer A 3 Secure the belt stop assembly to the deck in the loca tion shown Note The belt stop D Figures 7 amp 8 is located and ori ented differently in 44 and 50 applications For all 50 Models applications when turbo is installed belt stop D should a en srs 4 P se be outside the belt 1 8 away from the backside of the C Capscrew 5 16 18 x 1 1 2 5 16 belt 44 Models A Spacer D Belt Stop B 5 16 Washers E Lockwasher C Capscrew 5 16 18 x 1 1 2 5 16 Initial Turbo Installation Q Original Pulley and Spacer AA N ly
14. d Support C Hitch Plate of hitch plate C Secure with rod D and hair pin B Hair Pin D Rod B 11 Initial Hitch amp Tube Installation Upper Tube Middle Tube Lower Tube Nut Nylock 10 24 x 3 4 Washer Screw Truss Head 10 24 Holes Clip and Hardware A B C D E F G H Figure 4 Assemble Tubes 8 Deflector Assemble Tubes 4 Deflector 1 Insert the lower tube C Figure 4 into middle tube B Secure the tubes as shown in Figure 4 using 10 24 x 3 4 screws washer E and 10 24 nuts D Insert middle tube B into upper tube A Secure the tubes as shown in Figure 4 using 10 24 X 3 4 screws washer E and 10 24 nuts D 2 Place upper tube into catcher opening Secure the elbow to the turbo using clip H Note Relocation of clip and hardware H to holes G may be necessary to ensure proper fit Use correct hole locations to maintain proper tube connections and pre vent lower tube from disconnecting from the turbo Assemble Catcher Bags 1 See Figure 6 Insert the wire hoop H through the cloth bag B 2 Install the clamp E and hanger bracket D Secure with two 5 16 18 x 3 4 carriage bolts C lockwashers G and nuts F 12 Figure 6 Assemble Catcher Bags A Clip B Cloth Bag C 5 16 18 x 3 4 Carriage Bolt D Hanger Bracket E Clamp F Nut G Lockwasher H Wire Hoop Setup Initial Collector Assembly COLLECTOR ASSEMBLY Install Cover
15. deck from the unit see Operator s Manual for instructions Deflector Removal 1 Remove and retain the carriage bolts washers lock washers and nuts A Figure 3 holding the deflector rod to the deck Remove and discard the deflector rod Retain the deflector Figure 3 Remove Deflector A Carriage Bolts Washers Lockwashers amp Nuts Install Discharge Baffle 1 Attach the baffle bracket A Figure 4 under the mower housing as shown and insert the carriage bolt from step 1 through the bracket amp deck hole at B 2 Attach the L bracket C to the baffle A and over the stone guard D Attach with carriage bolt spacer lockwasher and nut as shown Figure 4 Install Discharge Baffle A Baffle Bracket C L Bracket B Mounting Hole D Stone Guard Figure 2 Install Discharge Baffle A Cover and Bolts Install Deflector Hinge Assembly 1 Remove the bolts A Figure 2 securing the RH arbor cover then remove the cover from the deck Discard the cover and bolts A 2 Remove and discard the plastic plugs from the deck at the locations used by bolts F amp B Figure 5 3 Slide the deflector rod D through the pivot bracket E 4 Secure the front of the pivot bracket with a 5 16 18 x 3 4 carriage bolt F and flange whizlock nut C Figure 5 Install Deflector Hinge 5 Secure the back of the pivot bracket E and belt Belt Cover Support F 5 16 18 x 3 4
16. done assemble the anchor bracket and related components as shown in Figure 11 2 Attach the anchor bracket assembly B Figure 12 to the mower deck using 5 16 18 x 1 capscrews A and 5 16 18 locknuts C NOTE The deflector latch MUST secure the deflector in A GOWN ROSMON AS SKO VM I PIQUE Z A Capscrews 5 16 18 x1 C Locknut 5 16 18 B Anchor Bracket Initial Turbo Installation Figure 13 Belt Cover Plates A Belt Cover Plate for 50 Mower B Belt Cover Plate for 44 Mower A WARNING When the turbo blower assembly is removed from the mower deck the deflector MUST be properly installed Install Belt Cover Plate 1 Attach the belt cover plate B Figure 13 8 14 to the support bracket E using a 5 16 18 x 1 capscrew C washer D and nylock nut F NOTE This cover plate must be able to pivot on the support bracket Different belt covers are reguired for different applications Refer to Figure 13 2 Rotate the belt cover until the notch catches the idler assembly belt cover latch A Figure 14 Cover latch A may need to be rotated for proper alignment Install Turbo Belt 1 Locate the correct drive belt for your installation 44 models reguire drive belt 1705142 50 models reguire drive belt 1707956 the part number is stamped on the belt 2 Loosen the hardware securing the drive pulley belt guide B Figure 15 amp 16 and the idler pulley C 3 Install the drive belt as shown in F
17. gure 8 Remove the cover E 3 Remove and empty the bags C Figure 9 4 Warning Back plate A will fall when rod D is removed Remove the hair pin B Figure 10 and Figure 10 Install Back Plate A Back Plate amp Support C Hitch Plate rod D while holding back plate A B Hair Pin D Rod 5 Lift back plate amp support assembly A Figure 10 off hitch plate D 14 Removing and Reattaching Grass Catcher Installing the Grass Carcher 1 Set the back plate amp support A Figure 11 on pins of hitch plate C Secure with rod D and hair pin B 2 Install the bags C Figure 12 3 Install the cover E Figure 12 Secure with the cle vis pins F and hair pin clips B NOTE Push the hair pin clips all the way on or they will be bent by the hinge when the cover is opened 4 Connect the cover cable Figure 8 5 Insert the tubes A Figure 12 into the catcher and connect to the turbo Be sure the clip F is secured over the top of the turbo flange nut Figure 11 Install Back Plate A Back Plate amp Support C Hitch Plate B Hair Pin D Rod Tubes Hair Pin Clip Bags Clevis Pin Cover Clip Figure 12 Normal Removal amp Installation 15 Hardware Identification Torgue Specifications Common Hardware Types Torgue Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE Tolerance 20 Carriage Bolt TES CI Standard Hardware
18. igures 15 8 16 4 Tighten the hardware securing the drive pulley belt guide B and idler pulley C The idler belt guide should be within 1 16 of the belt Install Mounting Bracket 1 See Figures 15 8 16 Locate and remove the two longer capscrews used to secure the rear of the turbo housing and idler spring anchor 2 Install the turbo mounting bracket A using the removed hardware Note that the bracket is mounted in two different positions depending on the applica tion Figure 14 Install Belt Cover Plate A Belt Cover Latch E Support Bracket B Belt Cover Plate F Nylock Nut 5 16 C Capscrew 5 16 18 x 1 D Washer 5 16 Figure 15 Belt Routing 44 Models A Mounting Bracket B Drive Pulley Belt Guide Hardware C Idler Pulley Hardware D Mounting Bracket Hardware Figure 16 Belt Routing 50 Models A Mounting Bracket B Drive Pulley Belt Guide Hardware C Idler Pulley Hardware D Mounting Bracket Hardware Initial Turbo Installation Install Turbo Blower 1 Install the turbo unit by sliding the turbo pivot rod into the pivot bracket at the front edge of the mower deck A Figure 17 2 Tilt the deflector UP B 3 Rotate the turbo unit C into position on the dis charge of the mower deck and latch the slot in the turbo housing over and onto the anchor bracket at D Tighten the wing nut E to secure Figure 17 Install Turbo Blower A Pivot Bracket D A
19. isting Ni Hardware gt a SL SN v 17 F Z A A 0 ge 2 Existing Hardware Bolt Washer Lockwasher 8 Nut M 40 Existing Hardware Ref Oty Description 17 2 WASHER Flat 3 8 34 1 WASHER 3 8 1 2 CAPSCREW Hex Head 5 16 18 x 1 18 1 CAPSCREW Hex Head 3 8 16 x 2 35 1 V BELT 50 Turbo 2 6 WASHER 5 16 19 1 PULLEY ASSEMBLY Idler 36 1 NUT Hex Lock 5 16 18 3 1 SUPPORT Belt Cover 20 1 BELT STOP 37 1 NUT Wing Special 5 16 4 4 NUT Hex Nylon Lock 10 24 21 1 CAPSCREW 5 16 18 x 1 1 2 38 2 NUT Hex 5 16 18 5 1 ROD Deflector 22 8 LOCKWASHER 5 16 39 1 BRACKET Anchor 6 4 SCREW Truss Head 10 24 x 3 4 23 1 SPACER 40 1 CARRIAGE BOLT 5 16 18 7 1 PIVOT ASSEMBLY 24 1 NUT Sleeve 41 1 BRACKET ASSEMBLY Cutoff 8 4 NUT Hex Whizlock 5 16 18 25 1 WASHER Belleville 42 1 SPACER 9 1 NUT Nylock Hex 5 16 18 20 1 PULLEY 43 1 BRACKET 10 1 COVER BELT 50 27 1 HUB 44 2 CAPSCREW Hex Head 5 16 18 x 7 8 11 1 DECAL Warning 28 1 PLATE Spring Support 40 1 CARRIAGE BOLT 5 16 18 x 3 4 12 1 COVER BELT 44 29 1 SPACER Pulley 46 1 SPRING Compression 13 1 NUT Hex 3 8 16 30 1 CAPSCREW Hex Head 5 16 18 47 1 SPACER Spring Holder 14 1 LOGKWASHER 3 8 31 1 WASHER 5 16 48 1 BRACKET Mounting 15 1 BRACKET Idler 32 1 LATCH Spring 49 1 V BELT 44 Turbo 16 1 LATCH Belt Cover 33 1 SPACER Figure 1 Contents of Turbo Installation Kit Initial Turbo Installation TURBO INSTALLATION Remove Mower Deck Remove the mower
20. nchor Bracket B Deflector E Sleeve Nut C Turbo Install Turbo Drive Belt 1 See Figure 18 Attach the turbo belt to the top RH Mower Deck pulley on the mower deck Pull back on the belt ten Turbo Drive Pulley sloning lever to slacken the belt A view from right front of mower of the belt routing is shown at right S ee NOTE While attaching it may be necessary to unlatch Arbor Pulley the turbo and realign the belt on the pulleys inside the 7247 ToSlacken FRONT turbo housing N f Belt 2 After the belt is installed adjust the belt stop D Turbo Drive Figure 11 8 12 so that it is 1 8 away from the back eb side of the belt Secure Belt Cover 1 The belt cover plate A Figure 19 is a safety shield after attaching or detaching the turbo unit it MUST BE rotated onto the belt cover latch B CAUTION Before you begin operating the unit with the Turbo attached be certain you have read all of the safety and operational information on the last page of this instruction sheet as well as the Operator s Manual for the tractor and any grass catchers or other collection devices used in conjunction with this turbo blower Figure 19 Belt Cover A Belt Cover Plate B Belt Cover Latch Initial Counter Balance amp Weight Garrier Installation Figure 1 Counter Balance Installation COUNTER BALANCE 8 WEIGHT CARRIER INSTALLATION Counter Balance Installation 1 Remove hair pin C Figure
21. ules 8 Information General Warning nr 2 Safety Decals 2 hasia ku at r 2 Storing the Grass Catcher 3 General Operating Information Before ODerAION ee okn ko 3 Mowing with the Catcher 3 Required Accessories 3 Alter Operation zese ou ti or kari ivan 3 Storing the Grass Catcher a nnenannnnennnnannne 3 Initial Turbo Installation Contents Turbo Installation K i 4 Turbo Installation onen n 5 Initial Counter Balance 84 Front Weight Carrier Installation Counter Balance Installation s 10 Front Weight Carrier Installation 10 Initial Hitch 8 Tube Installation Install Hitch Plate 8 Back Plate 11 Assemble Tubes amp Deflector s 12 Assemble Catcher Bags 12 Table of Contents Initial Collector Assembly Install Cover amp Bags c ssccecssseeeseeeeeeeeees 13 Normal Removal 8 Installation Removing the Grass Catcher 14 Installing the Grass Catcher 15 Hardware Identification amp Torque Specifications 16 NOTE In these instructions left and right are referred to as seen from the operating position Safety Rules amp Information unit severe personal injury or death to you or bystanders or damage to property or equipment The trian Read these safety rules and follow them closely Failure to obey these rules could result in
Download Pdf Manuals
Related Search