Home
Sanyo MPR-1411 Refrigerator User Manual
Contents
1. 3 In the case of MPR 1411R remove the rail that is placed vertically at the center of the frame Connector water 4 Pull the lamp toward the rear together with the cover as shown in Fig 1 together with the wiring 5 Take out the lamp and remove the connector water proof rubber at both ends As shown in Fig 2 shift the rubber by rolling it 6 Remove the connector as shown in Fig 3 7 Take out the lamp by pulling it gently from the cover 8 After replacing a new lamp return the lamp with cover to the original position Socket 62 24 ROUTINE MAINTENANCE A glow starter is located inside the front cover 1 Disconnect the power supply plug Water proof rubber 2 Remove the water proof rubber 3 Remove the glow starter and replace with a new one 4 Replace the water proof rubber Cleaning of condenser filter 25 1 Lift the front cover as shown in the figure 2 Take out the shaft and insert the end of the shaft in the black hole of the front cover 3 After holding black handle of condenser filter and having raised it aloft remove the condenser filter 4 Absorb a dirt of condenser filter with leaning machine or wash it away with water Condenser 5 Cut water of condenser filter well when used water 6 After cleaning the condenser filter return it to the original position 63 TROUBLE SHOOTING If the unit malfunctions check out the following befo
2. Clean the unit once a month Regular cleaning keeps the unit looking new Use a dry cloth to wipe off small amounts of dirt on the outside and inside of the unit and all accessories If the outside panels are dirty clean them with a diluted neutral dishwashing detergent Undiluted detergent can damage the plastic components For the dilution refer to the instruction of the detergent After the cleaning with the diluted detergent always wipe it off with a wet cloth Then wipe off the cabinet or accessories with a dry cloth Never pour water onto or into the unit Doing so can damage the electric insulation and cause failure The compressor and other mechanical parts are completely sealed This unit requires absolutely no lubrication Cleaning of evaporating tray The evaporating tray is installed on the back on of the unit Clean the evaporating tray once a month 1 Remove the tray fixture under the evaporating tray by unscrewing 4 screws and the evaporating tray is free Fig 1 al Evaporating M tray 2 Wash away any accumulated dirt in the evaporating tray Tray fixture 3 Fix the evaporating tray with the tray fixture and 4 screws ye 23 ROUTINE MAINTENANCE The fluorescent lamp is placed vertically at the center of the chamber Follow the procedure below to replace the lamp 1 Turn off the fluorescent light switch and disconnect the power supply plug 2 Remove all shelves or drawers
3. SANYO INSTRUCTION MANUAL MPR 1411 MPR 1411R Pharmaceutical Refrigerator MPR 1411R CONTENTS INTRODUCTION PRECAUTIONS FOR SAFE OPERATION ENVIRONMENTAL CONDITIONS REFRIGERATOR COMPONENTS Control panel Inside of front cover INSTALLATION SITE INSTALLATION START UP OF UNIT STOCK OF CONTAINERS CHAMBER TEMPERATURE SETTING ALARM TEMPERATURE SETTING SETTING OF DELAY OF DOOR ALARM SETTING OF ALARM RESUME TIME KEY LOCK FUNCTION DEFROST CYCLES REMOTE ALARM TERMINAL ALARMS amp SAFETY FUNCTIONS ROUTINE MAINTENANCE Cleaning of cabinet Cleaning of evaporating tray Replacement of fluorescent lamp Replacement of glow starter Cleaning of condenser filter TROUBLESHOOTING DISPOSAL OF UNIT OPTIONAL COMPONENTS Automatic temperature recorder Attachment of recorder MTR 0621LH Attachment of recorder MTR GO4A Attachment of battery kit MPR 48B Setting for battery before starting SPECIFICATIONS PERFORMANCE SAFETY CHECK SHEET 39 U U u eee ee ON CN u u yu y U U U U U U U U U U U U U U U 23 23 24 25 25 26 21 32 32 33 35 37 38 38 39 INTRODUCTION m Read this manual carefully before using the appliance and follow the instructions for safety operation m Sanyo never guarantee any safety if the appliance is used for any objects other than intended use or used by any procedures other than those mentioned in this manual m Keep this manual in an adequate place to refer to it as necessary m The cont
4. heater defrost heater drain pipe heater OFF Compressor OFF Intermittent tone Unit keeps continuous running Remote alarm Intermittent tone Unit keeps continuous running Remote alarm Intermittent tone Intermittent tone Intermittent tone Intermittent tone Compressor of high stage side stops The alarm status of remote alarm terminal is cancelled by pressing the alarm buzzer stop key BUZZER since the remote alarm is operated in conjunction with alarm buzzer except for power failure alarm status When more than two alarm conditions occur simultaneously the lowest number error code has priority on the error display After a power failure the unit will resume operation with the set value that was in place before power failure occurred The over cooling protection may activate when the set temperature is 2 C temperature will rise to 6 C but this is not malfunction 60 In this case the chamber 22 ROUTINE MAINTENANCE WARNING Always disconnect the power supply to the unit prior to any repair or maintenance of the unit in order to prevent electric shock or injury Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance These may be harmful to your health NCAUTION Always wear dry gloves to protect hands at the time of maintenance Failure to wear gloves may result in injury from edges and corners Cleaning of cabinet
5. Other supply voltage fluctuations as stated by the manufacture 7 Transient overvoltages according to Installation Categories Overvoltage Categories Il For mains supply the minimum and normal category is Il 8 Pollution degree 2 in accordance with IEC 60664 45 REFRIGERATOR COMPONENTS 16 ai ff dy in nt NM NM 9 u wu LA IL IN 10 A LO x m N MPR 1411 O e td L ii Fi QUI ni i m Rear side MPR 1411R 46 REFRIGERATOR COMPONENTS 1 Front cover A front cover opens when a bottom part is pulled to the front Open this cover when you use cleaning of the condenser filter a remote alarm terminal Refer to page 11 2 Control panel Panel opens when the right top of the lower part cover is pushed Refer to page 10 3 Light switch This switch is used for turning the fluorescent lamp off and on 4 Space for temperature recorder An temperature recorder optional accessory can be mounted here See page 32 5 Fluorescent lamp 40 W white lamp See page 24 for replacement 6 Lock Turn the key clockwise through 180 to securely lock the door 7 Glass window The window may have condensation in high humidity environment Wipe off the condensation with a soft dry cloth 8 Handle Always hold the handle when opening closing the door 9 Dew receiv
6. by attaching a rope or chain between the wall and the fixtures Fig 2 4 Ground earth The ground earth is for preventing the electric shock in the case of the electrical insulation is somehow degraded Always ground the unit at the time of installation WARNING Use a power supply outlet with ground earth to prevent electric shock If the power supply outlet is not grounded it is necessary to install a ground by qualified engineers Never ground the unit through a gas pipe water main telephone line or lightning rod Such grounding may cause electric shock in the case of an incomplete circuit Bia 13 START UP OF UNIT Follow the procedures for the initial and consequent operations of the unit 1 Connect the power cord to the dedicated outlet with appropriate rating NCAUTION If the unit is unplugged or the power to the unit is interrupted do not restart the unit for at least 5 minutes This protects the compressor 2 On start up the alarm buzzer sometimes operates In this case stop the buzzer by pressing the alarm buzzer stop key BUZZER 3 Set the chamber temperature to 5 C 4 Allow the chamber temperature to fall to 5 C Check the chamber temperature on the temperature indicator 5 Turn on the fluorescent light switch to check the light After checking turn off the switch if the light is not necessary 6 Set the desired temperature When the chamber temperature gets
7. chamber temperature resulting from inadequate door close The available set range of delay time is between 1 and 15 minutes Initial setting factory setting is 2 minutes Table 4 Procedure for setting of delay of door alarm Change the delay time to 3 min from 2 min Description of operation Key operated Indication after operation j The current chamber temperature is displayed Press numerical value shift key for FOO is displayed and the first digit 5 seconds blinks The display is changed to F04 from Press up arrow key 4 times F00 The current setting 002 is displayed Press set key and the first digit blinks Press numerical value shift key and The tdi is changed to 003 from scroll the figure to 003 time is memorized and the Press set key current chamber temperature is displayed Note The set mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation In this case any setting before pressing set key SET is not memorized 56 18 SETTING OF ALARM RESUME TIME 19 The alarm buzzer and remote alarm are silenced by pressing he alarm buzzer stop key BUZZER on the control panel during alarm condition The buzzer and remote alarm will be activated again after certain suspension if the alarm condition is continued The suspension time can be set by followi
8. is flashed P the k hifts the digit which Set the temperature to 03 with the ressing the key shifts the digit whic can be set 5 digit shift key and numerical value 7 d Wher pressed the figure of settable shift key fom increases Alarm temperature is memorized and Press set key the current chamber temperature is displayed Table 3 Procedure for setting low temperature alarm n Description of operation Key operated Indication after operation The current chamber temperature is displayed P value shift key f 5 seconds 4 Press set key The first digit is flashed Press numerical value shift key and When pressed the figure of settable scroll the figure to 7 digit increases Set the temperature to 03 with the 5 digit shift key and numerical value 7 A ue pressed the figure of settable shift key ae am increases Alarm temperature is memorized and Press set key the current chamber temperature is displayed 55 SETTING OF DELAY OF DOOR ALARM The door check indicator is light when the door is opened and the alarm buzzer sounds with some delay to notice the door opening The delay time between lighting of the door check indicator and activation of the alarm buzzer can be changed Set an appropriate delay time according to the condition of use to prevent the rise of
9. items within this line NCAUTION Intake air vent Load line Stock space Load line Exhaust air vent AKIN Cooling air Container Side view Never store corrosive substances in this unit This may lead to damage to the inner components or electric parts 59 CHAMBER TEMPERATURE SETTING Table 1 shows the basic procedure for setting the chamber temperature Perform key operations in the sequence indicated in the table The example in the table is based on the assumption that the desired temperature is 10 C Note The unit is set at the factory with a chamber temperature of 5 C Table 1 Basic operation sequence Example Chamber set temperature 10 C u Description of operation Key operated Indication after operation The current chamber temperature is displayed P Press set key ser The second digit is flashed Connect the power supply plug By pressing key the settable digits Set to 010 with the numerical value moves shift key and digit shift key A fm pressed the figure of settable A increases Set temperature is memorized and the 4 Press set key current chamber temperature is displayed Note The temperature set mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation In this case the chamber temperature setting is not accepted The available set range of chamber temperature i
10. may cause electric shock or short circuit when the liquid is spilled Never bind process or step on the power supply cord or never damage or break the power supply plug A broken supply cord or plug may cause fire or electric shock N Do not use the supply cord if its plug is loose Such supply cord may cause fire or electric shock QD Never disassemble repair or modify the unit yourself Any such work carried out by an unauthorized person may result in fire or electric shock or injury due to a malfunction Disconnect the power supply plug if there is something wrong with the unit Continued abnormal operation may cause electric shock or fire D When removing the plug from the power supply outlet grip the power supply plug not the cord Pulling the cord may result in electric shock or fire by short circuit e Disconnect the power supply plug before moving the unit Take care not to damage the power cord A damaged cord may cause electric shock or fire e Disconnect the power plug when the unit is not used for long periods Keeping the connection may cause electric shock current leakage or fire due to the deterioration of insulation If the unit is to be stored unused in an unsupervised area for an extended period ensure that children do not have access and that doors cannot be closed completely D The disposal of the unit should be accomplished by appropriate personnel Remove doors to prevent accidents such as suffocatio
11. temperature setting through the key pad is not available The key lock is set in OFF at the factory Display Key lock is OFF Enable to change of temperature setting Key lock is ON Disable to change of temperature setting u Description of operation Key operated Indication after operation The current chamber temperature is G displayed cuni The first digit is flashed 2 Press digit shift key for 5 seconds Press numerical value shift key and A me pressed the figure of settable L scroll the figure to 1 rw increases The key lock is set to ON 4 Press set key The current chamber temperature is displayed Note e FOO is displayed if the numerical value shift key is depressed for about 5 seconds accidentally This display is for service personnel Do not change this display Present temperature is displayed automatically when the set key SET is pressed or about 90 seconds is passed without any key operation 58 20 DEFROST CYCLES Cycle defrost When the ambient humidity is high or a large amount of damp product is being stored inside the chamber there is a possibility that cycle defrost may not be enough to remove all of the frost on the evaporator In this case a forced defrost cycle can be initiated Forced defrost When the unit is operating under a forced defrost cycle the current chamber temperature and dF is displayed alternately
12. 2 fixtures are attached on the rear side of the unit These keep adequate space between the unit and wall and also can be used for fixing the unit See page 13 18 Evaporating tray Defrost water from the evaporator accumulates on the tray and evaporates into the atmosphere See page 23 for cleaning 47 REFRIGERATOR COMPONENTS Control panel 1 2 3 DOOR ALARM Bu ATURE C 7 6 5 4 1 Door check indicator DOOR The red LED lamp is lit when the outer door is opened 2 Alarm lamp ALARM This lamp is flashed when the audible alarm is activated 3 Digital temperature indicator This indicator shows the present chamber temperature or set temperature 4 Numerical value shift key 4 Pressing this key in the setting mode causes the numerical value to shift ON OFF of key lock can be selected by pressing this key in the key lock mode 5 Digit shift key bb Pressing this key in the setting mode causes the changeable digit to shift Key lock is available by pressing this key for more than 5 seconds in the temperature display mode Refer to page 20 for the key lock 6 Set key SET Temperature setting mode is led by pressing this key Once the key is pressed the changeable digit is flashed Pressing this key again after setting desired temperature the setting is stored into computer memory If there is no key operation for 90 seconds during the temperature setting mode the temperature setting mode is invalid automa
13. E03 and chamber temp displayed alternately Sensor abnormality Alarm lamp is flashed If the defrost sensor is short circuited E04 and chamber temp displayed alternately Alarm lamp is flashed If the compressor sensor is disconnected E05 and chamber temp displayed alternately Alarm lamp is flashed If the compressor sensor is short circuited E06 and chamber temp displayed alternately switch with setting after attachment Batter E When the battery switch is turned ON without E09 and chamber temp i chec MPR 48B displayed alternately Condenser temp In the event of failure of fan motor for cooling E10 and chamber temp abnormality the compressor displayed alternately Battery check When about 3 years have passed with the F 1 and chamber temp is with MPR 48B power switch on time to replace the battery displayed alternately When about 6 years have passed with the F 2 and chamber temp is Fan motor check power switch on time to replace the fan displayed alternately motor Note Buzzer Safety operation Intermittent tone with Remote alarm with about about 15 minutes delay 15 minutes delay Intermittent tone with Remote alarm with about about 15 minutes delay 15 minutes delay a a rer remowaam Intermittent tone Alarm status Intermittent tone with about 2 minutes delay Finishing of each setting mode Change of setting is disable Remote alarm
14. The disposal of the unit should be accomplished by appropriate personnel Always remove doors to prevent accidents such as suffocation 65 27 DISPOSAL OF UNIT English FOR EU USERS The symbol mark and recycling systems described below apply to EU countries and do not apply to countries in other areas of the world Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and or reused The symbol mark means that electrical and electronic equipment batteries and accumulators at their end of life should be disposed of separately from your household waste Note If a chemical symbol is printed beneath the symbol mark this chemical symbol means that the battery or accumulator contains a heavy metal at a certain concentration This will be indicated as follows Hg mercury Cd cadmium Pb lead In the European Union there are separate collection systems for used electrical and electronic equipment batteries and accumulators Please dispose of them correctly at your local community waste collection recycling centre Please help us to conserve the environment we live in German Fur EU Staaten Das Symbol und das erwahnte Wiederverwertungssystem gelten nur fur die Lander der EU und nicht fur andere Lander oder Gebiete in der Welt Die Produkte von SANYO werden aus hochwertigen Materialien und Komponenten gefertigt die sich wieder verwenden lassen Das Symbol bed
15. amber through the access port Fig 3 5 An attached binder two pcs is used for the fan cover of the top of the chamber as the Fig 4 and a temperature sensor is fixed 4 Route the capillary on the top of the chamber and fix it with the provided clip and screw Fig 5 5 Make a cut on the rubber caps so that the capillary can pass the caps and place them back on the access port inside and outside Fig 6 9 Bind the lead wire on the right upper side of the unit with the provided band 10 Remove the connector cap located on the right side and then connect the recorder power Fig 7 11 Attach the recorder on the front cover with a screw Fig 8 Connector for recorder power Space for temperature recorder a JD E Temperature Binder Capillary Fig 5 Capillary Ly Fig 6 Rubber ca 34 OPTIONAL COMPONENTS 35 The alarm lamp blinks and the alarm buzzer sounds to notice the power failure when a battery for power failure alarm is installed For the installation of the battery for power failure alarm a battery kit MPR 48B an optional component is necessary A battery for power failure alarm is included in the battery kit Contact Sanyo sales representative or agent for the installation of the battery kit MPR 48B 1 Remove the top cover on the right front of the Electrical box cover refrigerator top by unscrewing 4 screws Fig 1 Con
16. ance 2 to 14 C ambient temperature 5 to 0 C no load 2 to 23 C ambient temperature 0 to 35 C no load Temperature control range 2 to 23 C Power source 370 W Noise level Note The unit with CE mark complies with EC directives 76 38 AN CAUTION Please fill in this form before servicing Hand over this form to the service engineer to keep for his and your safety Safety check sheet 1 Refrigerator contents LlYes INo Risk of infection lYes LINo Risk of toxicity LlYes LINo Risk from radioactive sources LlYes LINo List all potentially hazardous materials that have been stored in this unit Notes 2 Contamination of the unit Unit interior LIYes LINo No contamination Yes No Decontaminated Yes LINo Contaminated LIYes LINo Others 3 Instructions for safe repair maintenance of the unit a The unit is safe to work on IYes No b There is some danger see below Yes LINo Procedure to be adhered to in order to reduce safety risk indicated in b below Date Signature Address Division Telephone Product name Model Serial number Date of Installation Pharmaceutical MPR 1411 Refrigerator MPR 1411R Please decontaminate the unit yourself before calling the service engineer ia 39 SANYO SANYO Electric Co Ltd Printed in Japan
17. ents of the manual will be subjected to change without notice due to the improvement of performance or functions m Contact Sanyo sales representative or agent if any page of the manual is lost or page order is incorrect m Contact Sanyo sales representative or agent if any point in this manual is unclear or if there are any inaccuracies m No part of this manual may be reproduced in any form without the expressed written permission of Sanyo NCAUTION SANYO guarantees the product under certain warranty conditions SANYO in no way shall be responsible for any loss of content or damage of content 40 PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with this manual as it contains important safety advice Items and procedures are described so that you can use this unit correctly and safely If the precautions advised are followed this will prevent possible injury to the user and any other person Precautions are illustrated in the following way WARNING Failure to observe WARNING signs could result in a hazard to personnel possibly resulting in serious injury or death CAUTION Failure to observe CAUTION signs could result in injury to personnel and damage to the unit and associated property Symbol shows PAN this symbol means caution N this symbol means an action is prohibited this symbol means an instruction must be followed Be sure to keep this manual in a place accessible
18. er The condensation on the outer door is accumulated on this dew receiver Wipe off the water on the dew receiver with a cloth 10 Leveling foot Adjust the height of the leveling feet by turning the screw bolts until the unit is level 11 Caster When installing the unit the castors can be raised from the floor by using the leveling feet above 12 Drawer MPR 1411R only Items to be stored in the chamber must be placed on the drawers The maximum storage weight for each drawer is 40 kg Shelf MPR 1411 only Items to be stored in the chamber must be placed on the shelves The maximum storage weight for each shelf is 50 kg Do not put stored items directly onto the interior floor of the chamber See page 15 13 Access port This port allows temperature measurement cables to enter the chamber from outside A total of three 3 ports are provided left side right side and top 14 Exhaust air vent Do not block this vent If this vent is blocked temperature regulation will become unstable Do not place stored items in the path of the cold air 15 Intake air vent Do not block this vent If this vent is blocked temperature regulation will become unstable Do not insert a finger or any foreign object into this vent as there is danger from the internal fan 16 Door switch When a door opens a fan for the cold circulation is stopped and the leakage of the cold is prevented And the check lamp of the door is turned on 17 Fixture
19. ery before starting 10 Switch on the battery switch on the battery box 74 CX It is fixed behind the electrical box cover with a clip To the battery gt EN Na a NIE us e battery 36 OPTIONAL COMPONENTS Setting for battery before starting 37 Always perform the setting shown below after the installation of battery for power failure alarm an optional component MPR 48B The chamber temperature and E09 is displayed on the temperature display alternately if the battery switch is turned on without following procedure Turn off the battery switch perform the following setting and turn on the battery switch again if E09 is displayed on the temperature display Description of operation Key operated Indication after operation ao The current chamber temperature is displayed Press numerical value shift key for FOO is displayed and the first digit Dr main 2 fm The display is changed to F02 from twice A Press numerical value shift key 4 A The display is changed to F42 from times The current setting 000 is displayed In N Press set ke LIL LI and the first digit blinks GIGI Press numerical value shift key and The display is changed to 001 from oa AE The setting is memorized and Press set key SET the current chamber temperature is displayed 75 SPECIFICATIONS Name Pharmaceutical Refrigerator Model MPR 1411 MPR 1411R External dime
20. eutet dass elektrische oder elektronische Gerate Batterien und Akkus am Ende ihrer Lebensdauer nicht im Haushaltmull entsorgt werden durfen Hinweis Ein chemisches Zeichen unter dem Symbol bedeutet dass die Batterie bzw der Akku Schwermetalle in gewissen Konzentrationen enth lt Die Metalle werden wie folgt bezeichnet Hg Quecksilber Cd Kadmium Pb Blei In der Europ ischen Union gibt es separate Sammelstellen f r elektrische und elektronische Ger te Batterien und Akkus Entsorgen Sie solche Ger te bitte richtig in der kommunalen Sammelstelle bzw im Recyclingzentrum Helfen Sie mit die Umwelt in der wir leben zu sch tzen 66 28 DISPOSAL OF UNIT 29 French POUR LES UTILISATEURS DE UE Le symbole et les systemes de recyclage voqu s ci dessous s appliquent uniquement aux pays de UE Votre produit SANYO est concu et fabriqu avec des composants et des mat riaux de hautes qualites qui peuvent tre recycl s et ou r utilis s Le symbole signifie que les quipements lectriques et lectroniques les batteries et les accumulateurs ne doivent pas tre mis au rebut avec les d chets domestiques a l issue de leur dur e de vie Remarque Si un symbole chimique est imprim sous le symbole le symbole chimique indique que la batterie ou l accumulateur contient une certaine concentration de m taux lourds Les m taux sont indiqu s de la mani re suivante Hg mercure Cd cadmium Pb plomb II exis
21. ge kwaliteit die gerecycleerd en opnieuw gebruikt kunnen worden Het symbool betekent dat elektrische en elektronische apparatuur batterijen en accu s aan het eind van hun leven apart van uw huisafval weggegooid moeten worden Let op Indien een chemisch symbool afgedrukt staat onder het symbool betekent dit chemisch symbool dat de batterij of accu een zwaar metaal met een bepaalde concentratie bevat Dit wordt als volgt aangegeven Hg kwik Cd cadmium Pb lood In de Europese Unie zijn afzonderlijke inzamelingssystemen voor gebruikte elektrische en elektronische apparatuur batterijen en accu s Wilt u deze op de juiste manier weggooien bij uw plaatselijk afvalinzameling recyclingcentrum in uw buurt Help ons het milieu waarin wij leven in stand te houden Swedish FOR ANVANDARE INOM EU Den symbolmarkning och de atervinningssystem som beskrivs har nedan galler lander inom EU och g ller inte lander i n gon annan del av v rlden Din SANYO produkt har konstruerats och tillverkats med delar och material av h g kvalitet som kan atervinnas och eller ateranvandas Symbolmarkningen innebar att elektrisk och elektronisk utrustning batterier och ackumulatorer vid slutet av deras livslangd inte far slangas som hushallsavfall utan skall slangas separat Observera Om en kemisk symbol finns tryckt under denna symbolmarkning betyder denna kemiska symbol att batteriet eller ackumulatorn inneh ller en tungmetall med en viss koncen
22. iagnostic functions Table 7 Alarms and safety functions Alarm amp Safety Situation Indication High temperature If the chamber temperature deviates from the Alarm lamp is flashed set temperature 2 C or up to 14 C If the chamber temperature deviates from the set temperature 2 C or up to 14 C If the chamber temperature is lower than 0 C When the chamber temp is higher than 40 C Reset when the chamber temp is lower than 30 C When the chamber temp is lower than 1 C alarm Chamber temperature is flashed Low temperature Alarm lamp is flashed alarm Chamber temperature is flashed Over heat protection Over coolin 3 Reset when the chamber temp is higher than 6 C protection Power failure NE it When the power to the unit is disconnected alarm Power failure alarm At power failure Alarm lamp blinks with MPR 48B If the power supply cord is unplugged When the door is open Door check lamp is lit When there is no key pressing in each setting Chamber temperature is Auto return mode for 90 seconds displayed Key lock When the key lock is ON am Alarm lamp is flashed E01 and 50 C or 50 C are displayed alternately If the thermal sensor is disconnected Alarm lamp is flashed E02 and 50 C or 50 C are displayed alternately If the thermal sensor is short circuited Alarm lamp is flashed If the defrost sensor is disconnected
23. ico significa que la bateria o acumulador contiene una cierta concentracion de un metal pesado Esto es indicado de la siguiente manera Hg mercurio Cd cadmio Pb plomo En la Union Europea hay sistemas de recolecci n separados para equipos el ctricos y electr nicos baterias y acumuladores usados Por favor disponga de ellos correctamente en el centro de recolecci n de residuos reciclado de la comunidad de su localidad Por favor ayudenos a proteger el medio ambiente en que vivimos 67 DISPOSAL OF UNIT Portuguese PARA UTILIZADORES DA UE O simbolo e os sistemas de reciclagem descritos abaixo aplicam se aos paises da UE e nao se aplicam aos paises noutras areas do mundo O seu produto SANYO foi concebido e fabricado com materiais e componentes de elevada qualidade que podem ser reciclados e ou reutilizados O simbolo significa que o equipamento el ctrico e electr nico baterias e acumuladores em final de vida nao devem ser deitados fora juntamente com o lixo dom stico Atenc o Se estiver impresso um simbolo quimico debaixo do simbolo de este simbolo quimico significa que a bateria ou acumulador contem um metal pesado numa determinada concentrac o Estara indicado da seguinte forma Hg mercurio Cd cadmio Pb chumbo Na Uniao Europeia existem sistemas de recolha separados para equipamento el ctrico e electronico baterias e acumuladores Por favor entregue os no seu centro de reciclagem recolha de lixo l
24. ipe water main telephone line or lightning rod Such grounding may cause electric shock in the case of an incomplete circuit Connect the unit to a power source as indicated on the rating label attached to the unit Use of any other voltage or frequency other than that on the rating label may cause fire or electric shock S Never store volatile or flammable substances in this unit if the container cannot be sealed These may cause explosion or fire Do not insert metal objects such as a pin or a wire into any vent gap or any outlet on the unit This may cause electric shock or injury by accidental contact with moving parts Use this unit in safe area when treating the poison harmful or radiate articles Improper use O may cause bad effect on your health or environment e Turn off the power switch if provided and disconnect the power supply to the unit prior to any repair or maintenance of the unit in order to prevent electric shock or injury Do not touch any electrical parts such as power supply plug or operate switches with a wet hand This may cause electric shock 42 PRECAUTIONS FOR SAFE OPERATION NWARNING Ensure you do not inhale or consume medication or aerosols from around the unit at the time of O maintenance These may be harmful to your health N Never splash water directly onto the unit as this may cause electric shock or short circuit Never put containers with liquid on the unit as this
25. lammable or corrosive gas Never install the unit in a flammable or volatile location This may cause explosion or fire or may result in the current leakage or electric shock by the corrosion of the electrical components NCAUTION Never install the unit in a location where the corrosive material such as sulfur compound is likely to be generated near a drainage facilities etc Corrosion of the copper pipe may result in deterioration of cooling unit and consequently the failure m A location without the possibility of anything fall Avoid installing the unit in the location where anything can fall down onto the unit This may cause the breakdown or failure of the unit 50 12 INSTALLATION 1 Removing the packaging materials and tapes Remove all transportation packaging materials and tapes Open the doors and ventilate the unit If the outside panels are dirty clean them with a diluted neutral dishwashing detergent Undiluted detergent can damage the plastic components For the dilution refer to the instruction of the detergent After the cleaning with the diluted detergent always wipe it off with a wet cloth Then wipe off the panels with a dry cloth 2 Adjusting the leveling foot Extend the leveling feet by _ rotating them counterclockwise until they make contact with the floor Fig 1 Ensure the unit is level 3 Fixing the unit Two fixtures are attached to the rear of the frame Fix the frame to the wall
26. n N Do not put the packing plastic bag within reach of children as suffocation may result 43 PRECAUTIONS FOR SAFE OPERATION NCAUTION Use a dedicated power source a dedicated circuit with a breaker as indicated on the rating label attached to the unit A branched circuit may cause fire resulting from abnormal heating Connect the power supply plug to the power source firmly after removing the dust on the plug A dusty plug or improper insertion may cause a heat or ignition S Never store corrosive substances such as acid or alkali in this unit if the container cannot be sealed These may cause corrosion of inner components or electric parts O Check the setting when starting up of operation after power failure or turning off of power switch The stored items may be damaged due to the change of setting amp Be careful not to tip over the unit during movement to prevent damage or injury D Prepare a safety check sheet when you request any repair or maintenance for the safety of service personnel 44 ENVIRONMENTAL CONDITIONS This equipment is designed to be safe at least under the following conditions based on the IEC 61010 1 1 Indoor use 2 Altitude up to 2000 m 3 Ambient temperature 5 C to 40 C 4 Maximum relative humidity 80 for temperature up to 31 C decreasing linearly to 50 relative humidity at 40 C 5 Mains supply voltage fluctuations not to exceed 10 of the nominal voltage 6
27. nce with the following conditions may cause poor performance failure or accident m A location not subjected to direct sunlight Do not install the unit under direct sunlight Installation in a location subjected to direct sunlight may degrade the performance m A location with adequate ventilation Leave at least 10 cm around the unit for ventilation Poor ventilation will result in a reduction of the performance and consequently the failure m A location away from heat generating sources Avoid installing the unit near heat emitting appliances such as a heater or a boiler etc Heat can decrease the intended performance of the unit m A location with little temperature change Install the unit under stable ambient temperature Installing the unit under unstable ambient temperature may result in unstable performance m A location with a sturdy and level floor Always install the unit on a sturdy and level floor withstanding the total weight of the unit The uneven floor or tilted installation may cause failure or injury Unstable condition may cause vibration or noise m A location not prone to high humidity Install the unit in the ambient of 80 R H or less humidity Installation under high humidity may cause current leakage or electric shock NCAUTION The unit may collect excessive frost on the evaporator if it is installed in high temperature and high humidity location This will cause frequent defrosting m A location without f
28. ng the procedure shown in the Table 5 below The example in the table is based on the assumption that the desired duration is 20 minutes Note The duration is set in 30 minutes at the factory Table 5 Procedure for setting of alarm resume time Example change from 30 minutes to 20 minutes P _ Key operated Indication after operation The current chamber temperature IS displayed PEUR we The first digit of the temperature shift key for about 5 seconds display blinks Pene Set to F25 by using digit shift key digit _ of the current digit The current set value is displayed and 4 Press the set key the second digit of the temperature display flashes The value is stored in memory and Press the set key the current chamber temperature is Set to 020 by using numerical value Pressing the key shifts up the figure in 5 am shift key the second digit Note The settable alarm resume times are 10 20 30 40 50 or 60 minutes The set values are 010 020 030 040 050 and 060 The buzzer would not reset if the resume time is set in 000 The set mode returns to the temperature display mode automatically when 90 seconds has passed without any key operation In this case any setting before pressing set key SET is not memorized 57 KEY LOCK FUNCTION This unit is provided with a key lock function When the key lock is ON change of
29. nsions W1440 x D830 x H1950 mm Internal dimensions W1320 x D710 x H1500 mm Effective capacity 1364 L 1359 L Painted steel Painted steel Double layer pair glass steel plate automatic closing mechanism 2 doors Rigid polyurethane foamed in place Shelf Hard steel wire on polyethylene coating 8 pcs Painted steel Drawer 10 pcs Left side right side top side Inner diameter 30 mm D O Forced cool air circulation Hermetic type Output 250 W Fin and tube type Fin and tube type R 404A Forced type Fully automatic 257 W Microprocessor control system Internal heater Temperature controller Temperature display Digital display Alarm High temp Low temp Door Power failure Over heat and cooling protection Allowable contact capacity DC 30 V 2A Memory back up Nonvolatile static memory Fluorescent lamp White light 40 W x 1 Glow starter FG 4P Accessories Remote alarm contact J D ni 7 3 Q 1 set of key 1 nylon clip 2 binders O m O x Oo D 2 gt e 3 D fn O O Weight 248 kg 287 kg Optional component Automatic temperature recorder MTR 0621LH Recorder fixture MPR S30 Automatic temperature recorder MTR G04 Recorder fixture MPR S7 Battery kit for power failure alarm MPR 48B Interface board MTR 480 LAN interface board MTR LO3 Note Design or specifications will be subject to change without notice PERFORMANCE Cooling perform
30. ocal Por favor ajude nos a conservar o ambiente Italian PER UTENTI UE Il simbolo e i sistemi di riciclaggio descritti di seguito si applicano esclusivamente ai paesi dell UE Questo prodotto SANYO stato progettato e realizzato con materiali e componenti di elevata qualit che possono essere riciclati e o riutilizzati Il simbolo di riciclaggio mostrato di seguito indica che i dispositivi elettrici ed elettronici le batterie e gli accumulatori una volta esauriti devono essere smaltiti separatamente rispetto ai rifiuti domestici Nota Se sotto il simbolo di riciclaggio appare un simbolo chimico esso sta ad indicare che la batteria o l accumulatore contengono metalli pesanti a determinate concentrazioni Questo viene specificato come segue Hg mercurio Cd cadmio Pb piombo Nell Unione europea esistono diversi sistemi per la raccolta dei rifiuti speciali quali i dispositivi elettrici ed elettronici le batterie e gli accumulatori Si raccomanda di provvedere allo smaltimento di tali rifiuti secondo quanto previsto dalle normative vigenti in materia Aiutaci a conservare l ambiente 68 30 DISPOSAL OF UNIT 31 Dutch VOOR GEBRUIKERS IN DE EU Het symbool en de recycleersystemen die hieronder beschreven worden zijn van toepassing op de landen in de EU en zijn niet van toepassing op landen in andere delen van de wereld Uw SANYO product is ontworpen en gemaakt met materialen en onderdelen van ho
31. on the digital temperature display The chamber temperature rises about 10 C during the defrosting NCAUTION The unit may collect excessive frost on the evaporator if it is installed in high temperature and high humidity location For example the unit starts to defrost once a week with 2 C setting in the ambient of 35 C and 80 R H The chamber temperature goes up to approximately 10 C temporarily during defrosting REMOTE ALARM TERMINAL 21 Note The terminal of the remote alarm is installed at the back of the unit The alarm is generated from this terminal The contact capacity is DC 30 V 2 A Contact output Between COM and N O Between COM and N C At normal condition Open Close At abnormal condition Close Open The alarm status of remote alarm terminal is cancelled by pressing the alarm buzzer stop key BUZZER since the remote alarm is operated in conjunction with alarm buzzer Connecting ur terminal The remote alarm terminal is in alarm status when the NE CNTG REMORTE ALARM MAX DC30V 2A power supply cord is unplugged because it is regarded as a power failure In this case the alarm status of remote alarm terminal is not cancelled by pressing the alarm buzzer stop key BUZZER 69 ALARMS amp SAFETY FUNCTIONS This unit has the alarms and safety functions shown in Table 7 and also self d
32. re calling for service Malfunction Check Remedy If nothing operates even There is a power failure when switched on The circuit breaker is activated The unit is not connected to the power supply When no key operation is The key lock is set in ON L 1 available The alarm device is lt On start up gt activated The temperature in the unit does not match the set value lt In use gt The door was kept opened for a long time The temperature setting was changed The containers of high temperature load were put in the unit In these cases alarm is removed automatically by running the unit for several hours When unit does not get A large amount of items or warm product was put in the unit cold enough The air exhaust vent is blocked up with containers The unit is in direct sunlight The door is frequently opened There is a nearby heat source The ambient temperature is too high The door is not securely closed The heat source is put in the unit The door seal is damaged or foreign substance is inserted between door gaskets Note If the malfunction is not eliminated after checking the above items or the malfunction is not shown in the above table contact Sanyo sales representative or agent 64 26 DISPOSAL OF UNIT WARNING If the unit is to be stored unused in an unsupervised area for an extended period ensure that children do not have access and doors cannot be closed completely
33. s between 2 and 23 C The partial freezing may occurred if the set temperature is lower than 3 C 54 16 ALARM TEMPERATURE SETTING 17 This unit is provided with both high and low temperature alarms The temperature at which the alarm is activated may be changed The available set range for high temperature alarm is between 2 C and 14 C and 2 C and 14 C for low temperature alarm against the chamber temperature Note The temperature alarm is set at 5 C of the set temperature at the factory Display Function High temperature alarm set See Table 2 on page 17 Low temperature alarm set See Table 3 on page 17 As an example Table 2 shows the procedure to set the high temperature alarm so that the alarm can activate when the chamber temperature is 3 C higher than the set temperature Table 3 shows the procedure to set the low temperature alarm so that the alarm can activate when the chamber temperature is 3 C lower than the set temperature Table 2 Procedure for setting high temperature alarm Description of operation Key operated Indication after operation The current chamber temperature is displayed P ical value shift key f i ne A The first digit is flashed 5 seconds Press numerical value shift key and When pressed the figure of settable scroll the figure to 6 digit increases 3 Press set key ser The first digit
34. te diff rents syst mes de collecte pour les quipements lectriques et lectroniques les batteries et les accumulateurs usag s au sein de l Union europ enne Veuillez mettre les quipements au rebut de mani re correcte aupr s de votre centre de recyclage de collecte des d chets local Aidez nous pr server l environnement dans lequel nous vivons Les machines ou appareils lectriques et lectroniques contiennent fr quemment des mati res qui si elles sont trait es ou limin es de mani re inappropri e peuvent s av rer potentiellement dangereuses pour la sant humaine et pour l environnement Cependant ces mati res sont n cessaires au bon fonctionnement de votre appareil ou de votre machine Pour cette raison il vous est demand de ne pas vous d barrasser de votre appareil ou machine usag avec vos ordures m nag res Spanish PARA USUARIOS DE LA UNION EUROPEA El simbolo y los sistemas de reciclado descriptos a continuaci n se aplican para paises de la Union Europea y no se aplica para paises en otras areas del mundo Su producto SANYO fue disenado y fabricado con materiales de alta calidad y componentes que pueden ser reciclados y o vueltos a usar El simbolo significa que los equipos el ctricos y electr nicos baterias y acumuladores al final de su vida util debe ser desechados separadamente de sus residuos domiciliarios Nota Si hay un simbolo quimico impreso debajo del simbolo este simbolo quim
35. tically See page 16 for the details 7 Buzzer stop key BUZZER To silence the audible alarm press this key The remote alarm is also silenced by pressing this key The buzzer cannot be stopped during remote alarm testing 48 10 REFRIGERATOR COMPONENTS 1 2 3 4 5 TD Je HA SLI So da Tr DOE PR III MULTI ul LABCOOL LTCC LL 4 LLLLLI H LLLLLLLLLLLLECLLI E LATTES 1 Condenser filter This filter is for prevention of condenser clogged up Clean the filter every 3 month 2 Remote alarm terminal This is used to connect the unit to an exterior alarm to notify users of any malfunction Refer to page 21 3 Glow starter This is for the fluorescent lamp It is recommended that the glow starter is also replaced when the fluorescent lamp is replaced Refer to page 25 4 Circuit breaker Make sure to switch ON this breaker before starting up of the unit This disconnects the power when any abnormality is occurred and over current is rushed Contact with dealer or service station after disconnect the power supply plug Rated AC 250 V 10 A 5 Fixture rear side 2 fixtures are attached on the rear side of the unit These keep adequate space between the unit and wall and also can be used for fixing the unit See page 13 49 11 INSTALLATION SITE To operate this unit properly and to obtain maximum performance install the unit in a location with the following conditions m A location not complia
36. ting kit which fixed a temperature recorder in the front cover Fig 3 4 Remove the black rubber caps inside and outside on the access port located at the top corner of the unit and take the insulation out of the access port 5 Pass the recorder sensor into the chamber through the access port Fig 4 Temperature recorder sensor 70 e 32 OPTIONAL COMPONENTS 6 An attached binder two pcs is used for the fan cover of the top of the chamber as the Fig 5 and a temperature sensor is fixed 7 Route the capillary on the top of the chamber and fix it with the provided clip and screw Fig 6 8 Make a cut on the rubber caps so that the capillary can pass the caps and place them back on the access port inside and outside Fig 7 Capillary Fig 6 Capillary ky Fig 7 Rubber ca Attachment of recorder MTR G04 1 Unscrew the screw fixing the panel cover at the space for temperature recorder and open the panel cover Fig 1 2 Fix the temperature recorder to the frame in the temperature recorder mounting kit MPR S7 referring to the instruction manual enclosed with the temperature recorder mounting kit Fig 2 Recorder 71 33 OPTIONAL COMPONENTS 3 Remove the black rubber caps inside and outside on the access port located at the top corner of the unit and take the insulation out of the access port 4 Pass the recorder sensor into the ch
37. to the set temperature begin slowly placing items into the chamber to minimize the temperature rise CAUTION The chamber is refrigerated by the forced circulation of cooled air inside the chamber Ensure that the intake and exhaust air vents are not blocked Adequate space should be provided between the items inside the unit to allow air circulation lt Attention gt The outer door has a condensation on the glass during refrigerator operation Wipe off the condensation with a dry soft cloth Also wipe off the water on the dew receiver regularly 62 14 15 STOCK OF CONTAINERS Always distribute items so as not to disturb the air circulation in the chamber Disruption of the air flow can cause items to freeze or reduce the uniformity of the chamber temperature Never put any articles on the top of the unit Intake air vent Do not block this vent with containers If this vent becomes blocked temperature regulation becomes unstable Do not place paper or vinyl near the vent as they may be sucked into the fan Exhaust air vent Do not block this vent with containers as this can impede air circulation Items stored near the exhaust air vent can freeze when the refrigerator is operating at temperature settings lower than 5 C Load line In this refrigerator storage space is limited to allow the passage of cool air around the chamber The label load line is fixed to both sides of the chamber Always stock
38. to users of this unit lt Label on the unit gt This mark is labeled on the cover in which the electrical components of high voltage AN are enclosed to prevent the electric shock The cover should be removed by a qualified engineer or a service personnel only 41 PRECAUTIONS FOR SAFE OPERATION WARNING Do not use the unit outdoors Current leakage or electric shock may result if the unit is exposed to rain water Only qualified engineers or service personnel should install the unit The installation by unqualified personnel may cause electric shock or fire Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from turning over If the floor is not strong enough or the installation site is not adequate this may result in injury from the unit falling or tipping over Never install the unit in a humid place or a place where it is likely to be splashed by water Deterioration of the insulation may result which could cause current leakage or electric shock N Never install the unit in a flammable or volatile location This may cause explosion or fire S Never install the unit where acid or corrosive gases are present as current leakage or electric shock may result due to corrosion Gr ground earth the unit to prevent electric shock If the power supply outlet is not grounded it will be necessary to install a ground by qualified engineers S Never ground the unit through a gas p
39. tration Detta indikeras pa foljande satt Hg kvicksilver Cd kadmium Pb bly den Europeiska Unionen finns det separata uppsamlingssystem for anvand elektrisk och elektronisk utrustning batterier och ackumulatorer G r dig av med s dana saker p r tt s tt p den speciella lokala platsen f r tersamling teranv ndning Hj lp oss att bevara den milj vi lever i 69 OPTIONAL COMPONENTS Automatic temperature recorder An automatic temperature recorder is available for this refrigerator as an optional accessory If an automatic temperature recorder is required contact your Sanyo dealer Two recorders are selectable for the refrigerator MTR 0621LH and MTR G04 Please note that each recorder needs a exclusive fixture for mounting See the following for the details Temperature recorder Recorder fixture MTR 0621LH MPR S30 MTR G04 MPR S7 Attachment of recorder MTR 0621LH The temperature record range of the temperature recorder MTR 0621LH is 20 C from 6 C Temperature of 20 C and more cannot be recorded 1 Unscrew the screw fixing the panel cover at the space for temperature recorder and open the panel cover Fig 1 een Panel cover 2 Fix the temperature recorder to the frame in the temperature recorder mounting kit MPR S30 referring to the instruction manual enclosed with the temperature recorder mounting kit Fig 2 3 Fix the temperature record installation temperature recorder moun
40. trol panel cover 2 Remove a electrical box cover from the control panel cover and remove harness from the clip which harness is fastened with behind the electrical box cover Fig 1 2 3 Pass the harnesses through the bottom opening of the battery box and set the battery box on the control panel of the refrigerator top so that four screw holes can be aligned Fig 3 The battery box should be located with the battery switch Harness faced to the refrigerator front 4 Put the battery on the left of the battery box Fig 3 Mir ie OPTIONAL COMPONENTS 5 Put the battery fixture over the battery and fix the battery box and battery fixture by four screws Fig 4 6 Each harness is connected to the battery connectors Fig 5 and switches to a fixed mounting plate on the battery clip Fig 4 6 Connect the harness to the battery connector and battery switch Fig 6 and bind the harnesses by the clip on the battery fixture 7 Cover the opening beside the battery switch with the top The harness in no use is bound by the clip on the back of the top cover cover removed in procedure 2 four screws 8 Put the battery box cover over the battery box and fix the battery box cover with screws three screws on the right and left Fig 6 9 Perform the setting for battery through the keys on the control panel of refrigerator Refer to the procedure on the next page Setting for batt
Download Pdf Manuals
Related Search
Related Contents
scanpro20 - LaserShowParts advertencia - Bard Manufacturing Company Overdrive User Manual rev 2.0.pages Nikon 13311 Digital Camera User Manual Symmons 543TR-STN Instructions / Assembly HAEMATOKRIT 210 cocción automática Comment lire les étiquettes 電気通信サービスの広告表示に関する自主基準及びガイドライン「別冊 Copyright © All rights reserved.
Failed to retrieve file