POSIFLEX Business Machines KS-6812 Computer Monitor User Manual
Contents
1. ILLES aR ADO BE A Part 202. DISCONNECTING ALL CABLES With the LCD panel turned to most backward position the main I O connector area will be easily accessible at bottom side of the main unit Please first note orientations of every existing cable connection and then disconnect every cable properly before any further reconfiguration of cable connections Please note that the click lock spring has to be pressed down prior to pulling out the connector such as the LAN port or the CR port or the alternate RJ45 form COM3 port Please also note that the fixing screws have to be loosened free prior to disconnection such as the 2 regular DB9 form COM ports or the VGA port Please always hold the connector head instead of pulling on the cable wire when disconnecting any connector Failure to do this could damage the cable and jack that 1s considered as an artificial destruction Damages due to incorrect disconnection operation are not covered by product warranty Part 6 OPENING BASE BACK COVER In order to settle the touch terminal properly in a point of sale system all the cable connections have to be routed through its base Therefore please observe the side view pictures of the base trunk at the left and release the triangle marked hooks to remove the back cover CABLE ROUTING IN BASE For cable routing in the mini slim base please refer to the picture at left There is a cable tie inside the base trunk as arrowed in the picture Hold all the external cables wit
3. 5 one VGA port 6 one SATA data port plus one HDD power connector for optional SATA HDD in base 7 one audio jack for stereo line output 8 one CR port capable of controlling 2 cash drawers max 9 one 2 pin type DC 12 V power input connector 10 reserved one LPT interface through use of optional special cable in service window Built in 1 internal 2W speaker Touch control functions left right button double click drag amp draw Dynamic video memory technology up to 224 MB Support high performance DDR2 SDRAM with maximum memory size 2GB in two SODIMM Integrated structure for side mount upgrade kit with software programmable MSR parameters for Win XP or WEPOS Accidental power off protection The power switch located at a recessed side of main unit is unlikely to be activated in normal operation Preconditioned power up function by alarm clock or COM port MODEM ring or LAN Supports power saving by suspension mode Option Items Note The underlined items in the following list means that option must be a b c d e set prior to shipment from the factory The rest items can be set by the dealers DDR2 SODIMM memory expansion up to 2GB max CF card reader in HDD bay HDD in main unit will not be applicable Base installation kit for HDD Integrated side mount upgrade kit lt SD 680 with options of MSR and optical fingerprint sensor in USB interface Integrated base mount upgrade kit lt LCD Pole displa
4. All brand and product names and trademarks are the property of their respective holders P N 16590900010 Part 1 o _ ALERT TO OUR HONORABLE CUSTOMERS O Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it Don t take any premature action before you have a full understanding of the consequences This product contains inside a Lithium battery Please always follow local environmental protection laws regulations for disposal of used batteries and always replace only with battery of same type DAILY MAINTENANCE GUIDE For regular cleaning of the KS systems please use only soft haired brush or dry soft cloth You may use moist soft cloth to remove stains when necessary Apply only proper amount of mild neutral detergent for obstinate stains Please note that never use Acryl dissolving solvent or Polycarbonate dissolving solvent You may apply ammonia based glass cleaner only on the screen surface CAUTION Risk Of Explosion If Battery Is Replaced By An Incorrect Type Dispose Of Used Batteries According To Local Regulations Part 2 o Nh INTRODUCTION PRODUCT PICTURES Front View Rear View Side Views Bottom View Inside Base PARTS IDENTIFICATION l Ze 3 4 Main unit Touch panel LCD panel Power indicator Base stand Part 3 Optional side mount kit HDD cover Hinge cover Base back cover 9 Cable exit 10
5. When the KS 6812 system is turned off after a successful boot up with external power continuously supplied the preset automatic power on functions will keep monitoring for the preset conditions and turn on the system when the preset conditions are met Please note that 1f the KS 6812 system 1s improperly turned off before a complete boot up procedure the above preset power on control functions will be disabled until next turning off after a complete boot up BRIGHTNESS CONTROL At left side of the main unit below the power switch there are brightness adjust push button switches and two USB connectors Each single press on the or button changes the LCD panel display brightness by a small amount When you press and hold the button the change w ll keep on until release or extreme condition matched USB PORTS There are in total 6 USB ports for external connection 2 at left side below power switch and LCD brightness adjust buttons 4 In I O area All of them comply to USB 2 0 standard Part 12 o CUSTOMER DISPLAY Please follow the instructions on the manual that comes along with the customer display when lt 1s installed DISPLAY ISSUES Main LCD Display For best viewing result please set your display resolution at 1024 x 768 with high color The system Video Memory is shared from system memory The video memory size is default 8 MB and can be set to be 1 MB VGA Port The VGA port in the KS 6812 system supports ei
6. loss of data or profits resulting from the furnishing performance or use of this material This information is provided as is and Posiflex Technologies Inc expressly disclaims any warranties expressed implied or statutory including without limitation implied warranties of merchantability or fitness for particular purpose good title and against infringement The information in this manual contains only essential hardware concerns for general user and is subject to change without notice Posiflex reserves the right to alter product designs layouts or drivers without notification The system integrator shall provide applicative notices and arrangement for special options utilizing this product The user may find the most up to date information of the hardware from web sites http www posiflex com or http www posiflex com tw or http www posiflexusa com All data should be backed up prior to the installation of any drive unit or storage peripheral Posiflex will not be responsible for any loss of data resulting from the use disuse or misuse of this or any other Posiflex product All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without prior express written consent from Posiflex Technologies Inc the publisher of this documentation Copyright Posiflex Technologies Inc 2009
7. IDE channel 1 Master device The CF memory card reader inside main unit accepts a type II CF memory card Please note that usual utilities such as FDISK EXE or FORMAT COM must never be used on CF card or permanent damage can occur If this option is installed the standard SATA HDD in main unit is not applicable HDD amp SATA PORT The 2 5 HDD in the main unit is connected to the system through internal Serial ATA SATA connector The optional HDD in the base unit if installed is connected to the system through SATA port The internal SATA HDD will be detected as Ch 0 M and the HDD connected to the SATA port will be detected as Ch 0 S in Advanced BIOS Features gt Hard Disk Boot Priority of BIOS setup Both IDE or SATA controller can be set to Disabled in Integrated Peripherals gt OnChip IDE Device of BIOS setup when required TOUCH PANEL All paragraphs below are applicable for models with touch panel only The user of those models without touch panel can ignore them and consider this user s manual ends here Mouse Emulation The touch panel in KS system uses USB interface When the touch driver is properly installed this touch panel works exactly like a standard mouse of USB interface However if the system is running under safe mode most drivers are disabled in this mode and the touch panel calibration 1s therefore not guaranteed It 1s recommended to use a standard USB mouse or ke
8. POUSIFLEX KS 6812 _ Fan Free Touch Terminal User s Manual Rev Original FCC Notes This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference Warranty Limits Warranty terminates automatically when any person other than the authorized technicians opens the machine The user should consult his her dealer for the problem happened Warranty voids 1f the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application About This Manual Posiflex Technologies Inc has made every effort for the accuracy of the content in this manual However Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein nor for direct indirect incidental consequential or otherwise damages including without limitation
9. Power switch 11 LCD brightness up button 12 LCD brightness down button 13 Base back cover hook 14 USB ports on left side 15 Sundries trough for pencils paper clips etc 16 Rubber feet with fixing screws 17 Screw holes for base mount kit 18 Oval cable passage on cast base trunk 19 Cable tie for all cables 20 Screw posts for optional HDD in base PRODUCT FEATURES Standard Features CPU Intel Atom N270 1 6G Fan free structure for harsh environment Data storage device SATA HDD 2 5 80 GB or optional CF card reader adaptor amp CF card in main unit An advanced mini slim base design that supports storage room for optional 2 5 SATA HDD Support WinXP Pro WEPOS and Linux OS High quality 12 TFT active matrix LCD panel Vertical type LCD panel with easy tilt angle adjustment from 20 to 90 LCD brightness adjust buttons at side of main unit Durable resistive type touch panel that endures 35 million touches min at same spot Various I O ports supported including 1 3 serial ports with 2 in form of DB9 connectors and 1 in form of 10 pin RJ45 type modular connector All are with capability for 5V DC support 2 6 standard USB ports with 2 at side and 4 in I O area below panel 3 two internal proprietary USB ports for touch function and optional side mount kit 4 one LAN port Ethernet 10 100 1000 Base T with LAN status indicators on jack green for link orange for data transmission E N Part 4
10. This switch controls the power on off of the system This switch turns the system on when pushed only when external power is present This switch turns the system off when pushed again during power on status However if the system hangs due to any reason such as software resource conflict a simple push on the switch may fail to turn off the power In this case please utilize the forced power off feature by pressing the switch and holding Part 11 z for within 10 seconds There must always be at least 10 seconds waiting before switching on again once the system is powered off successfully Automatic Power On Control The system may also turn on according to some preset conditions such as Modem Ring Up or Alarm Clock Wake Up or LAN Wake Up To utilize Modem Ring Up or Alarm Clock Wake Up function the user should enter the BIOS setup by pressing Del key at system boot up choose in Power Management Setup and make the Power On by Ring enabled for Modem Ring Up or enable the Resume by Alarm for Alarm Clock Wake Up Save the configuration and exit the BIOS setup program The Preset Power On Control will then be ready For LAN wakeup the item PCI Express PM Function must be enabled in Power Management Setup and an operating caller system connected through LAN to the system 1s required It also requires a qualified networking technician to check the LAN chip ID of the system for the caller system to wake up
11. h the cable tie Have all cables to pass through the oval hole on the trunk as triangle marked to come out of the front side of trunk Connect all the cable ends to main unit Should there is the option SATA HDD in base installed please double check that the HDD cables must be still secured BASE MOUNT UPGRADE KIT Luella Pole Display For the KS 6812 series with mini slim base the LCD customer display PD 309 U or the VFD PD 2605 U can be attached to either rear corner of base bottom Refer to the pictures at right Use the 3 attached screws to fix the metal base plate of the PD to bottom plate of mini slim base at the circled positions the holes marked with KS on bottom plate of PD against the holes marked P on bottom plate of KS system Connect the interface cable to go into the base through cable exit arrowed at right to the main unit Part 7 o PREPARING THE MAIN UNIT On the back of the main unit there is a service window facing the base trunk in most of MM application It is recommended to tilt the LCD panel to most backward position and rest the surface of LCD panel over a piece of soft clean cloth on a desktop to access the service window Use a screw driver of adequate length to remove the service window a Window lock screw to open the cover plate and find several Lock Screw jumpers as illustrated in the lower right picture The jumpers in this window are mainly designated for COM port powe
12. hout preloaded OS is highly discouraged Posiflex shall not be responsible for any technical support to questions arisen due to non preloaded OS Part 10 USING THE TOUCH TERMINAL APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines Ventilation This terminal must NOT be operated in an environment with restricted ventilation There must be at least 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit at ALL times for the installation Operating Environment The equipment must not be operated or stored in extremes of both temperature and humidity moisture Operating range 5 C to 40 C and up to 80 humidity non condensing max wet bulb 26 C Power Supply The operating voltage range of the power adaptor should cover the local power supply for proper operation The power cable the power outlet and any power fusing arrangements must conform to local safety regulations Please never do any connection disconnection when system is still powered on Please always keep the external power adaptor in a free air circulation POWER ON OFF CONTROL Power Indicator There is a power indicator LED at center of lower rim of LCD panel This LED lights up orange when external power is ready and turns to blue when system power is turned ON Hardware Power Switch The power switch located at left side of the main unit is a tactile pushbutton switch
13. pite of the fact that it is used in the way like an ordinary HDD usual utilities such as FDISK EXE or FORMAT COM shall never be used on CF Card otherwise the boot sector of operating system itself may be damaged and causing the CF Card no longer bootable For KS 6812 systems preloaded with Windows XP Pro or WEPOS on HDD Posiflex provides recovery DVD delivered with the touch terminal for the preloaded operating system The System Integrator shall take care of software restoration after OS recovered A Posiflex supplied USB interface COMBO drive will be required for such action Other brand COMBO drive may require its specific driver different from what supported in the recovery DVD Please use the recovery DVD in rescue operation only Using it otherwise may wipe out whatever stored in the HDD All upgrade devices drivers needed for manual installation in usual way are available in the subfolder drivers in OS recovered HDD and the latest versions of these required drivers will be available on our web http www posiflex com tw Then follow instructions from your system integrator for software recovery OPERATING SYSTEM INSTALLATION This product is a highly professionalized equipment The installation of an OS into a machine without any preloaded OS could constitute major difficulty for average user or obstacle by possibly unintentional negligence even for PC veterans to accomplish such a task Therefore OS installation into a system wit
14. r supply function Please consult your dealer for technical support on setup of these jumpers Please note that only those qualified technicians may adjust in the service window with information from Posiflex and the contents in the service window may change without notice as time develops The option LPT conversion cable should be applied to the connector as triangle marked in the picture Route the other end of the conversion cable through the oval opening in base trunk and have the usual cable for parallel device connected SIDE MOUNT UPGRADE KIT OPTION Remove the 2 screws circled in the left picture to remove the cover for side mount upgrade kit Take out the cable inside this cover and connect it to the white connector inside the side mount upgrade kit like SD 680 as arrowed in the right picture Gently arrange the excessive length of this cable back in the hole and screw fit it back to the position originally occupied by the cover Please reserve the cover if there is chance to have the side mount kit removed in the future Jumpers CONNECTING CASH DRAWER OPTION The RJ11 connector in main connection area of a KS 6812 system can be used for controlling most of the common cash drawers available on the market However it s most recommended that the Posiflex CR 2000 or CR 2200 or CR 3100 or CR 3200 or CR 4000 or CR 4100 or CR 4210 or CR 6310 be used for best compliance Part 8 o The KS system will directly cont
15. riate connectors Please make sure that each connector is connected to the correct port with the correct orientation Damages due to incorrect connection or orientation are not covered by product warranty Some connectors like the COM3 or LAN or CR connector have to be gently inserted until a click is heard It is recommended that connectors such as the COM 1 2 and VGA connector be screwed into place once seated Adjust the slack of each cable Re adjust the tilt angle of the screen for best viewing Connect the cables to appropriate external devices through the cable exit at the bottom of stand assembly Please make sure that each connector has to be connected to the right device in the right way CAUTION On doing any insertion or extraction of any connector please always hold the connector head itself instead of pulling on the cable wire Failure to do this could damage the cable and jack that is considered as an artificial destruction and is not covered by the warranty Part 9 o OPERATING SYSTEM RECOVERY For KS 6812 systems with operating system in the Compact Flash Card 1f the system 1s installed with the CF card reader once the Compact Flash is damaged for any reason the thin client may fail to boot A bootable new Compact Flash Card will be required to have the workstation back to work Please follow instructions given by the System Integrator to deal with situations like that One more advice for CF Card application is that in s
16. rol the cash drawer using the cash drawer port CR both to operate the opening mechanism and to monitor the drawer open status Both functions may be accomplished under software control of the COMI serial port Use the cable supplied with the cash drawer Part No 21863018010 for connection to the CR port in KS system This cable has a 6 pole plug at one end and an 8 pole plug at the other The 8 pole plug should be inserted into the connector marked signal cable from POS Printer at the rear of the cash drawer The 6 pole plug should be inserted in the connector marked CR found in the main connection area in the system The user may also purchase the optional 2 in 1 cash drawer control cable Part No 218630023800 to control 2 cash drawers In 1 port It has a 6 pole plug at one end and two 8 pole plugs at the other The 6 pole plug should be inserted in the connector marked CR found in the main connection area in the system Each 8 pole plug should be inserted into the connector marked signal cable from POS Printer at the rear of one of the cash drawers The cable lengths for the two 8 pole plugs are different Use the shorter one for the original cash drawer CR1 and use the longer one for the extended cash drawer CR2 that will be distinguished by the software command CONNECTING CABLES To have the re assembled main unit with stand assembly ready for operation please connect all required cables to the approp
17. ther a base mount 2 display or a separately connected LCD monitor or touch monitor To support the DC power to the 2 display monitor have a qualified technician to set an internal jumper in KS main unit to supply the required power through the VGA connector according to Posiflex technical information Do not connect other monitor to this port before the power in this port is disabled SERIAL PORTS COM1 2 3 In KS 6812 system there are 3 serial ports available All can supply a 5 V DC through pin 9 after proper jumper setting change COM1 2 ports are standard RS232 serial ports as status at delivery COM3 1s also set to standard RS232 serial port as status at delivery if the option conversion cable is applied PARALLEL PORT In KS 6812 system the parallel port can be available only through use of the optional conversion cable It should be connected to the special connector inside the service window as described earlier The other end of the cable is the normal 25 pin D sub female LPT connector AUDIO OUTPUT SPEAKER The audio port in KS 6812 system is arranged to have an internal audio speaker with maximum audio power of 2 W at lower left corner of the main unit The internal speaker will be automatically disconnected when a plug is inserted in the line output jack Part 13 o CF MEMORY CARD READER If the CF card reader is installed and the CF card is used for system data storage device it is recognized by the system as the
18. y PD 309U or lt V VFD Pole display PD 2605U Wireless LAN adaptor in USB interface Preload OS WinXP Pro WEPOS or Linux RJ45 to DB9 serial port conversion cable for COM 3 port Split cable for 2 cash drawer control Part No 21863018010 LPT interface conversion cable Part 5 o INSTALLATION GUIDES CAUTION Before any installation or cable connection to the set please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded Failure to do the above will void the product warranty TECHNICAL MANEUVERS Applicable technical maneuvers in KS 6812 series include serial COM port power supply settings VGA port power supply setting system CMOS data reset DRAM upgrades physical access to CF memory card 1f the CF card reader option 1s installed and installation of optional SATA HDD in base All these technical maneuver operations require purchase of applicable Technical Manual from Posiflex or consultation from Posiflex authorized dealers and should be handled only by a qualified technician TILTING LCD PANEL The tilting mechanism in KS 6812 series utilizes hinges and there is no particular skill to turn the LCD panel to most suitable angle for either viewing or convenience in cable connection disconnection
19. yboard in this mode All the below mentioned mouse emulation functions can be manipulated through relevant software The system can give a beep and a click on the left button of a mouse at the point when the touch panel is touched If the point touched is dragged across the screen surface it works as the mouse drag and drop feature If the point is touched released and touched within a short time interval it is double clicking left button of the mouse To obtain the effect like clicking on the right button of a mouse touching any point on the screen surface after touching the right click sticky button results as a click on the right button of the mouse at that point Part 14 o Posiflex USB Touch Manager A program named Posiflex USB Touch Manager and a right click sticky button tool in the program group Posiflex USB Touch Tools is installed in the preloaded Windows system with a USB interface touch panel controller This program can also be obtained by download from the POSIFLEX web site Part 15 Part 10 Part 17 Part 18 Part 19 POSIFLEX T31454
Download Pdf Manuals
Related Search