Home

Philips 105E19 Computer Monitor User Manual

1. e a product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications e incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you This includes but is not limited to prerecorded material whether copyrighted or not copyrighted e a product used for commercial or institutional purposes e A product that has been modified from the original design Where IS SERVICE AVAILABLE Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics In countries where Philips Consumer Electronics does not distribute the product the local Philips service organization will attempt to provide service although there may be a delay if the appropriate spare parts and technical manual s are not readily available Where CAN I GET MORE INFORMATION and HOW CAN I OBTAIN SERVICE file D EDFU LF3 If38manual english WARRANTY 7sxWAR_USA HTM 1 of 3 2003 3 27 10 40 58 United States Guarantee For more information contact the Philips Customer Care Center by calling 877 835 1838 U S A customers only or 903 242 4804 Before Requesting Service Please check your owner s manual before reques
2. LAITE SITEN ETTA VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA Plassering Ventilasjon ADVARSEL NAR DETTE UTSTYRET PLASSERES MA DU PASSE PA AT KONTAKTENE FOR STOMTILFORSEL ER LETTEA NA RETURN TO TOP OF THE PAGE BSMI Notice Taiwan Only TT BLAREM EM ES RETURN TO TOP OF THE PAGE Ergonomie Hinweis nur Deutschland Der von uns gelieferte Farbmonitor entspricht den in der Verordnung Uber den Schutz vor Schaden durch R ntgenstrahlen festgelegten Vorschriften Auf der R ckwand des Ger tes befindet sich ein Aufkleber der auf die Unbedenklichkeit der Inbetriebnahme hinweist da die Vorschriften ber die Bauart von St rstrahlern nach Anlage Ill u 5 Abs 4 der R ntgenverordnung erf llt sind Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht ist darauf zu achten da Reparaturen nur durch Fachpersonal durchgef hrt werden 2 nur original Ersatzteile verwendet werden 3 bei Ersatz der Bildr hre nur eine bauartgleiche eingebaut wird file D EDFU LF3 lf8manual english 105E SAFETY regs regulat htm 7 of 9 2003 83 27 10 40 14 Regulatory Information Aus ergonomischen Gr nden wird empfohlen die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden schlechte Lesbarkeit und erh hte Augenbelastung bei zu geringem Zeichenkontrast w ren die Folge Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betr gt 70dB A oder weniger
3. cathode are periodically scanned across a phosphor screen by means of deflection circuitry A special form of the cathode ray tube is the TV and monitor picture tube deflection cails electron i electron beam _ Phosphor screen cathode shadow mask i evacuated glass tube CustoMax Philips proprietary monitor control software that allows users to control parameters e g Size Color Geometry using software running in Windows CustoMax is compatible with existing VGA cards See CrystalClear FAQ and USB Bay FAQ RETURN TO TOP OF THE PAGE D DDC Display Data Channel DDC is a communication channel for displays and computers The DDC feature allows the monitor file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 3 of 18 2003 3 27 10 39 52 Glossary controller to be automatically configured to make optimal use of the display without manual user interaction DDC is implemented as part of the new Plug amp Play approach introduced into the PC market to increase user friendliness The three levels developed for Plug amp play are 1 DDC1 monitor send data to the PC 2 DDC2B PC can request information from monitor and 3 DDC2Bi which is a two way communication monitor can be addressed and PC or graphics board can give commands to monitor DDC 1 2B See DDC DDC 2Bi See DDC Degaussing The procedure of demagnetizing the shadow mask and associated metal parts
4. certified Technical Specifications CRT Size and deflection Dot pitch Grille pitch Horizontal pitch Tube type Phosphor Recommended display area Maximum display area SCANNING Horizontal scanning Vertical scanning VIDEO RETURN TO TOP OF THE PAGE 15 inch 38 cm 90 deflection angle 0 28 mm 0 24 mm Shadow mask flat square anti glare anti static 105E11 light transmission 5796 P22 10 6 x 7 95 270 x 202 mm 11 2 x 8 4 284 x 213 mm 30 54KHz 50 120 Hz file D EDFU LF3 lf8manual english 105E PRODUCT PRODUCT HTM 1 of 4 2003 3 27 10 39 51 105E Product Information Video dot rate 65 MHz Input impedance Video 75 ohm Sync 2 2 kOhm Input signal levels 0 7 Vpp Sync input signal Separate sync Sync polarities Positive and negative WHITE COLOR TEMPERATURE Chromaticity CIE coordinates at 9300 degrees K x 0 281 y 0 311 These information are subject to change without notice RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA s DPMS compliance display card or software installed in your PC the monitor can automatically reduce its power consumption when not in use And if an input from a keyboard mouse or other input device is detected the monitor will automatically wake up The following table shows the power consumption and signaling of this automatic power saving features Power Management Definition VE
5. d un technicien chevronn en radio t l vision Toutes modifications n ayant pas recu l approbation des services comp tents en mati re de conformit est susceptible d interdire l utilisateur l usage du pr sent quipement N utiliser que des c bles RF arm s pour les connections avec des ordinateurs ou p riph riques CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA RETURN TO TOP OF THE PAGE EN 55022 Compliance Czech Republic Only file D EDFU LF3 If3manual english 105E SAFETY regs regulat htm 3 of 9 2003 83 27 10 40 14 Regulatory Information This device belongs to category A devices as described in EN 55022 unless it is zpaciii cally stated that it is a Class A device on tha specification label The following applias to devices in Class A of EM 55022 radius of protection up to 30 meters Tha user of tha device is obliged to take all stapa necessary to remove sources of intarfarance to tela communication ar other devices Pokud neni na typowam amp titku potitate uwedeno e spad do do tidy A podle EN 55022 spada automaticky do tidy B podle EM 55022 Pro zafizeni zafazen do tidy A chrann p smo 30m podle EN 55022 plati n amp sledujici Dojde li k ru eni teleknrnunikainich nabo pnych zafizeni je u lvatel povinnen prov st takov opatrgnl aby ruseni odstranii RETURN TO TOP OF THE PAGE VCCI Notice Japan Only This
6. hub Downstream ports receive upstream data traffic Upstream The direction of data flow towards the host An upstream port is the port on a device electrically closest to the host that generates upstream data traffic from the hub Upstream ports receive downstream data traffic UPS Universal Power Supply The monitor with UPS feature can work in different countries with various mains voltage RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 16 of 18 2003 3 27 10 39 52 Glossary V Vertical dot pitch See Dot pitch Vertical scanning frequency Expressed in Hz this is the number of fields written to the screen every second in interlaced mode In non interlaced mode vertical scanning frequency is the number of frames complete pictures written to the screen every second also known as refresh rate Vertical sync pulses A train of square shaped waveforms that define the start of a new frame VESA Video Electronic Standards Association a consortium of manufacturers formed to establish and maintain industry wide standards for video cards and monitors VESA was instrumental in the introduction of the Super VGA and Extended VGA video graphics standards see Video graphics adapters with a refresh rate of 70 Hz minimizing flicker and helping to reduce operator eyes fatigue and stress Video dot rate See Dot rate Video graphics adapters A card equipped with a character or gr
7. is a Class B product based on the standard of the Voluntary Control Council for Interference VCCI for Information technology equipment If this equipment is used near a radio or television receiver in a domestic environment it may cause radio Interference Install and use the equipment according to the instruction manual VCI ZORE nn a ga 52 BRAT DOAR RRETHE S Us Lp T HE Lm Lea Tur LT HEISE AUE A ERES EY Hd IE DH MPI HE TE LU o EE EY Class B ITE 3 met ThE Zi RETURN TO TOP OF THE PAGE MIC Notice South Korea Only Class B Device Ea B AIRE OHS BR 717 l SAR 19402 448 44H86 MEY 4449 AE BE RE Medal dem gd file D EDFU LF3 If3manual english 105E SAFETY regs regulat htm 4 of 9 2003 3 27 10 40 14 Regulatory Information MIC Please note that this device has been approved for non business purposes and may be used in any environment including residential areas RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit a three prong socket All equipment that works together computer monitor printer and so on should have the same power supply source The phasing conductor of the room s electrical installation should have a reserve short circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes A To completely switch off the e
8. picture on the screen Please perform the following to correct the picture image e Reset your monitor via the OSD menu e Adjust the Horz width and or Vert size height in the OSD e Change monitor timing to work at the recommended resolution 43 The edge of the picture on the screen appears to be distorted How can I correct this Please perform the following to correct the picture image e A magnetic or electrical interference typically causes poor geometry in the picture Place the monitor in a different physical location e Reset the monitor to the factory preset via the OSD menu e Access the Geometry Menu in the OSD of the Monitor and perform the necessary adjustments file D EDFU LF3 If38manual english FAQ HTM 10 of 12 2003 83 27 10 39 51 Frequently Asked Questions e Change the monitor timing to the recommended resolution 44 The picture appears too dim How can I correct this Adjust Brightness and or Contrast via the monitor s OSD Some models have a Video Input Select under Advanced Controls in the monitor s OSD Most computers require it to be set at 0 7V Please review the following for possible solutions e li the OSD menu is also dim please contact service for repair e Reset the monitor via the OSD menu e Change the color temperature settings to 9300 color coordination via the OSD menu e Set the Contrast to maximum level 100 and Brightness to middle level 50 Video card could be defective try
9. temperature in degrees Kelvin of a black body radiating with the same dominant frequency as the source Most Philips monitors offer the possibility of setting the color temperature to any desired value Contrast The ratio between the brightness of the brightest and darkest parts of a picture The darkest part of a picture is set by the brightness of the unexcited phosphor which is governed by the degree with which ambient light is reflected Contrast is therefore reduced in conditions of high ambient light levels Black Matrix tubes reflect less ambient light so exhibit higher contrast than other tubes Convergence error Bean misalignment causing one or more of the three beams passing through the wrong aperture in the shadow mask and striking a phosphor dot in the wrong triad Convergence error is expressed in mm often at three well defined points on the screen designated A B and C see figure Also known as misconvergence file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 2 of 18 2003 3 27 10 39 52 Glossary Points where convergence error is specified Convergence error correction A method of correcting for convergence error to insure that all three beams land simultaneously in the same triad This is usually accomplished by means of special convergence error correction coils in the deflection yoke CHT Cathode ray tube the general term for all tubes in which one or more electron beams emitted by a
10. the monitor with another computer 45 have noticed two thin horizontal lines on the screen of my Philips monitor Is this normal This phenomenon can occur with Philips 107P 109P and 201P monitors and is normal Your monitor is using an Aperture Grille which consists of fine vertical wires to align the electron beams with the phosphors on the screen To prevent these vertical wires from vibrating and to keep them properly aligned with the picture tube two horizontal damper wires are required These are located on one third and on two third from the top of the screen The result is that you will see two very thin horizontal lines over your screen since the two wires are casting a slight shadow on the screen surface You will find these wires line in any monitor from Philips and other brands using the Aperture Grille technology 46 How canl increase the color display of my monitor The amount of video memory your video card holds determines the amount of colors that can be displayed on your computer screen To get the most out of your video card you will need to either install the latest drivers onto your computer or upgrade the video cards memory Please check with your computer or video card manufacturer for further details 47 Why is there no picture on my monitor e Check the wall socket for power Verify that there is power by connecting another product e Ensure the power cable is correctly attached to both the wall socket and
11. ACHTUNG BEIM AUFSTELLEN DIESES GER TES DARAUF ACHTEN DAB NETZSTECKER UND NETZKABELANSCHLUB LEICHT ZUGANGLICH SIND RETURN TO TOP OF THE PAGE End of Life Disposal Your new monitor contains materials that can be recycled and reused Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer RETURN TO TOP OF THE PAGE Information for UK only WARNING THIS APPLIANCE MUST BE EARTHED Important This apparatus is supplied with an approved moulded 13A plug To change a fuse in this type of plug proceed as follows 1 Remove fuse cover and fuse 2 Fit new fuse which should be a BS 1362 5A A S T A or BSI approved type 3 Refit the fuse cover If the fitted plug is not suitable for your socket outlets it should be cut off and an appropriate 3 pin plug fitted in its place If the mains plug contains a fuse this should file D EDFU LF3 lf8manual english 105E SAFETY regs regulat htm 8 of 9 2003 83 27 10 40 14 Regulatory Information have a value of 5A If a plug without a fuse is used the fuse at the distribution board should not be greater than 5A Note The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere How to connect a plug The wire
12. E file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 18 of 18 2003 83 27 10 39 52 Download and Print Download and Print This page provides an option to read the manual in pdf format PDF files can be downloaded into your hard disk then viewed and printed with Acrobat Reader or through your browser If you do not have Adobe Acrobat Reader installed click on the link to install the application Adobe Acrobat Reader for PC Adobe Acrobat Reader for Mac Download instructions To download the file 1 Click and hold your mouse over the icon below Win95 98 users right click 2 From the menu that appears choose Save Link As Save Target As or Download Link to Disk 3 Choose where you would like to save the image click Save if prompted to save as either text or source choose source Printing instructions To print the manual 1 With the manual file open follow your printer s instructions and print the pages you need Fal 105E pdf English language manual FOF LE pa 107B pdf FOF LE pa 107G pdf FOF JE m 107E pdf FOF m 107F pdf FOF IS Bs 107P pdf FOF pa 107S pdf FOF LE pA 107T pdf file D EDFU LF3 lf8manual english DOWNLOAD DOWNLOAD HTM 1 of 2 2003 3 27 10 39 53 Download and Print FOF E jd 107X pdf FOF E js 109B pdf Fa 109S pdf file D EDFU LF3 lf8manual english DOWNLOAD DOWNLOAD HTM 2 of 2 2003 3 27 10 39 53 Troubleshootin
13. G This icon indicates the potential for bodily harm and tells you how to avoid the problem SMART HELP This icon indicates helpful information when adjusting the On Screen Display of your monitor Some warnings may appear in alternate formats and may be unaccompanied by an icon In such cases the specific presentation of the warning is mandated by regulatory authority RETURN TO TOP OF THE PAGE 2003 Koninklijke Philips Electronics N V All rights reserved Reproduction copying usage modifying hiring renting public performance transmission and or broadcasting in whole or in part is prohibited without written consent of Philips Electronics N V file D EDFU LF3 If3manual english 105E ABOUT ABOUT HTM 2 of 2 2003 3 27 10 39 50 105E Product Information Product Information Product Features Technical Specifications e Automatic Power Saving Physical Specification Pin Assignment Product Views Product Features 105E11 12 16 e 15 inch 14 0 VIS color monitor with excellent front of screen performance for use with MACs and PCs e Autoscan covers horizontal frequencies up to 54 kHz offering a maximum resolution of 1024 x 768 with flicker free display of 800 x 600 at up to 87Hz e Flat square CRT with high resolution 0 28 mm dot pitch 0 24 hdp Smallest footprint in its class requires minimum desk space maximum depth is only 379 mm 14 9 e FCC CE in selected countries only and ISO9241 15014001
14. N TO TOP OF THE PAGE S Screen coatings file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 11 of 18 2003 83 27 10 39 52 Glossary standard tube F screen W 0 5 2 discharge time minutes Anti Static coatings Due to bombardment by beam electrons monitor screens become electrically charged when in use Electrically charged screens surfaces can attract dust particles An Anti Static coating is a conductive coating deposited on the screen or on a glass panel immediately in front of the screen that conducts away the charge and prevents screen dust build up AGAS Anti Glare Anti Static coating AGAS is a silica coating applied to the surface of the screen by a spinning and spraying process It operates by diffusing reflected light to blur images of light sources on the screen To provide anti static properties the coating is impregnated with small conductive particles ARAS Anti Reflection Anti Static coating ARAS is one of the most effective anti reflection anti static screen treatments currently available It is composed of a multi layer structure of transparent dielectric material that suppresses specular reflections by broadband interference effects at the screen surface Anti static properties are provided by a single conductive layer within the multi layer structure With ARAS the intensity of reflected light is reduced from around 4 5 of the incident light the reflectivity of uncoate
15. SA S Video H sync V sync Power Used Saving LED color Mode 96 ON Active Yes Yes lt 65W 0 Green OFF Blanked No No lt 8W 88 Yellow This monitor is ENERGY STAR compliant As an ENERGY STAR Partner PHILIPS has determined that this product meets the ENERGY STAR guidelines for energy efficiency RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english 105E PRODUCT PRODUCT HTM 2 of 4 2003 3 27 10 39 51 105E Product Information Physical Specifications 14 1 x 14 9 x 14 9 358 x 380 x 379 mm including base u 14 1 x 13 2 x 14 9 358 x 335 x 379 mm excluding base Weight 11 5 kg Power supply 90 264 VAC 50 60Hz Temperature operating 0 to 40 C 32 to 104 F Temperature storage 25 to 65 C 13 to 149 F Relative humidity storage 5 to 95 Resolution 800x 600 standard size contrast max brightness 50 9300 full white pattern These information are subject to change without notice RETURN TO TOP OF THE PAGE Pin Assignment The 15 pin D sub connector male of the signal cable IBM systems No pin 10 Logic ground 11 Identical output connected to pin 10 No 9 13 H Sync H V ES video input Green video input Blue video input video Blue video input Identical output connected to pin 10 5 Grunn 12 Serial data line SDA EN video ground 14 V Sync VCLK for DDC Green
16. aphic generator and video memory which maps to the screen A microprocessor scans video memory and translates bit information from the computer into displayable video signals for the monitor These cards comply with various standards that determine the nature and quality of the display VGA Video Graphics Array introduced in 1987 was the first analog card It offered still higher resolution than EGA 640 X 480 pixels for graphics and 720 x 400 pixels for text and a color palette of 256 colors VGA could also emulate EGA and CGA Super VGA devised by VESA in 1989 offers a resolution of 800 x 600 pixels Extended VGA introduced by VESA in 1991 offers a top resolution of 1024 x 768 pixels non interlaced and a refresh rate slightly higher than IBM s XGA 8514A High end graphics adapters introduced over the last three years for professional workstations offer top file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 17 of 18 2003 83 27 10 39 52 Glossary resolutions from 1280 x 1024 to 1600 x 1280 horizontal line frequencies up to 90 kHz and bandwidths up to 200 MHz VIS Viewable Image Size The real screen dimensions that users can see measured diagonally The VIS of a monitor is always less than the so called screen size of a monitor For example the VIS of a 17 inch monitor is only about 16 inches It depends on the useful screen size of CRT and the opening of a monitor s front cabinet RETURN TO TOP OF THE PAG
17. ar of your monitor 40 My monitor appears to be missing one or more colors How do I correct this If the OSD menu is also missing a color please contact service for details Set color temperature to 9300 color coordination Check the video cable for any bent pins Video card could be defective try the monitor with another computer file D EDFU LF3 If8manual english FAQ HTM 9 of 12 2003 3 27 10 39 51 Frequently Asked Questions 41 When I degauss my monitor it makes a loud noise Is this normal Yes when degaussing your monitor via the OSD it is normal for the monitor to make a relatively loud noise Please be aware that many models will not degauss more than once within any given time period up to 10 minutes This is due to the unit having a temperature sensitive resistor While the unit is degaussing the resistor increases in value with heat and once it reaches a certain temperature the resistance will rise and prevent voltage from reaching the degaussing coil This is what stops the degausser and this device s resistance will decrease as it cools back off enabling the degauss function to operate again This is an intentional design and is an industry standard not just for Philips monitors Please be aware that not all models in the Philips range has this manual degauss function Some models are built with an auto degauss feature which automatically degausses the monitor when it is switched on 42 How do I adjust the
18. atory Information CE Declaration of Conformity Energy Star Declaration Federal Communications Commission FCC Notice U S Only Commission Federale de la Communication FCC Declaration EN 55022 Compliance Czech Republic Only e VCCI Class 2 Notice Japan Only MIC Notice South Korea Only Polish Center for Testing and Certification Notice North Europe Information Nordic Countries BSMI Notice Taiwan Only Ergonomie Hinweis nur Deutschland Philips End of Life Disposal Information for UK only Safety Precautions and Maintenance Troubleshooting Other Related Information CE Declaration of Conformity e Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following standards EN60950 1992 A1 A2 A3 A4 A11 Safety requirement of Information Technology Equipment EN55022 1998 Radio Disturbance requirement of Information Technology Equipment EN55024 1998 Immunity requirement of Information Technology Equipment EN61000 3 2 1995 Limits for Harmonic Current Emission EN61000 3 3 1995 Limitation of Voltage Fluctuation and Flicker following provisions of directives applicable 73 23 EEC Low Voltage Directive 89 336 EEC EMC Directive 93 68 EEC Amendment of EMC and Low Voltage Directive and is produced by a manufacturing organization on ISO9000 level e The product also comply with the following standards SO9241 3 I80O9241 7 IS09241 8 Er
19. d by appropriate choice of frequency Autoscan MultiSync monitors which operate over a range of scanning frequencies may sometimes exhibit moir in certain video modes MPR See Electromagnetic radiation standards MultiSync monitor See Autoscan monitor RETURN TO TOP OF THE PAGE N Non interlaced See Interlaced non interlaced RETURN TO TOP OF THE PAGE O OSD On Screen Display The feature that allows an end user to adjust screen performance and parameters of monitors directly through an on screen instruction window See CustoMax in CrystalClear section Overscan The practice in which areas without useful video information are scanned outside the visible screen area in order to make maximum use of the screen for display of active video information This practice is occasionally necessary because some video cards generate a video pattern that is smaller than the visible file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 9 of 18 2003 3 27 10 39 52 Glossary screen area resulting in an image that is smaller and less legible than it needs to be RETURN TO TOP OF THE PAGE P Parallelogram Distortion See Geometric distortion Phosphor Generic name for the class of substances that exhibit luminescence To produce a picture on screen phosphors are deposited on the inner surface of the picture tube screen and excited into luminescence by the electron beam Typical examples of phosphors a
20. d screens to less than 0 5 ARAS also has a major advantage over other screen treatments It doesn t diffuse or scatter reflected light so picture contrast and sharpness remain completely unimpaired It s also easy to clean and tough enough to withstand commercially available cleaning agents file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 12 of 18 2003 83 27 10 39 52 Glossary light emitted by phosphor 0 5 of incident light Pan es a layer roughened inner glass phosphor The ARAS coating reflects only about 0 5 of the incident light AGRAS Anti Glare anti Reflection Anti Static coating A combined anti reflection anti glare anti static coating Self test function A monitor equipped with hardware or software to automatically detect cable connection status Shape Deviation of a reproduced picture from its intended shape The following types of distortion are most common file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 13 of 18 2003 3 27 10 39 52 Glossary SEP HR pincushion distortion WE c AR trapezoid distortion ES parallelogram distortion balanced pincushion distortion SOG Synchronization On Green A properly functioning color monitor requires five kinds of signals horizontal sync pulse vertical sync pulse red color signal green color signal and blue color signal Signals from a PC are transmitted to a monitor using one of three methods 1 Se
21. dards and deliver high quality performance ease of use and ease of installation Should you encounter any difficulties while installing or using this product please contact Philips directly to benefit from your Philips F1rst Choice Warranty This three year service warranty entitles you to a swap model on site within 48 hours of your call being received within the first year of purchase If you have any problems with your monitor within the second or third year of purchase we will repair it after it has been sent to the service provider at your expense and returned to you within five working days free of charge An extended warranty called Philips First Choice Premium is available in addition to your Philips First Choice warranty For more details contact your Philips dealer Before contacting Philips please prepare the following details so we can solve your problem quickly e Philips type number e Philips serial number e Purchase date copy of purchase may be required e PC environment Processor O 286 386 486 Pentium Pro Internal memory O Operating system Windows DOS OS 2 MAC o Fax Modem Internet program e Other cards installed Having the following information available will also help speed up the process e Your proof of purchase indicating date of purchase dealer name model and product serial number e The full address to which the swap model should be delivered Just a phone call away Philips customer help desks are located w
22. ding type attachment plug rated 15 A 250 V Information for Users outside the U S For units set at 230 V Use a Cord Set rated minimum 5 A 250 V for units set at 230V or 10A 125V for units set at 115V The Cord Set should have the appropriate safety approvals for the country in which the equipment will be installed RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english 105E SAFETY saf_other htm 2003 3 27 10 40 14 Front Controls Front Controls Power Hotkeys Digital Controls Adjustment Front Controls For an optimized adjustment of the picture following controls are available at the front Power Power Press this knob the green LED lights and the power is ON 2 Press this knob again the green LED disappears and the power is OFF RETURN TO TOP OF THE PAGE Hotkeys a Contrast Rotate to adjust the picture contrast level ES Brightness Rotate to adjust the overall screen brightness as a compensation for ambient light RETURN TO TOP OF THE PAGE Digital Controls file D EDFU LF3 lf8manual english Install_1 FRONT Front htm 1 of 3 2003 3 27 10 40 35 Front Controls Press to adjust increase the function selected Press to adjust decrease the function selected To select the level of function SHIFT LED off control is on first level SHIFT LED on control is on second level The function pads H Shift to adjust the hori
23. e exclusion of incidental or consequential damages so the above exclusion may not apply to you This includes but is not limited to prerecorded material whether copyrighted or not copyrighted e a product used for commercial or institutional purposes Where IS SERVICE AVAILABLE Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics In countries where Philips Consumer Electronics does not distribute the product the local file D EDFU LF3 lf8manual english WARRANTY WAR_USA HTM 1 of 3 2003 3 27 10 40 58 United States Guarantee Philips service organization will attempt to provide service although there may be a delay if the appropriate spare parts and technical manual s are not readily available Where CAN I GET MORE INFORMATION For more information contact the Philips Customer Care Center by calling 877 835 1838 U S A customers only or 903 242 4804 Before Requesting Service Please check your owner s manual before requesting service Adjustments of the controls discussed there may save you a service call TO GET WARRANTY SERVICE IN U S A PUERTO RICO OR U S VIRGIN ISLANDS Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for servicing Philips Customer Care Center 877 835 1838 or 903 242 4804 In U S A Puerto Rico and U S Virgin Islands all implied warranties inc
24. e which may result in fire or shock hazard do not expose this appliance to rain or excessive moisture THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS RETURN TO TOP OF THE PAGE Commission Federale de la Communication FCC Declaration Cet quipement a t test et d clar conforme auxlimites des appareils num riques de class B aux termes de l article 15 Des r gles de la FCC Ces limites sont concues de facon fourir une protection raisonnable contre les interf rences nuisibles dans le cadre d une A installation r sidentielle CET appareil produit utilise et peut mettre des hyperfr quences qui si l appareil n est pas install et utilis selon les consignes donn es peuvent causer des interf rences nuisibles aux communications radio Cependant rien ne peut garantir l absence d interf rences dans le cadre d une installation particuli re Si cet appareil est la cause d interf rences nuisibles pour la r ception des signaux de radio ou de t l vision ce qui peut tre d cel en fermant l quipement puis en le remettant en fonction l utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes e R orienter ou d placer l antenne de r ception e Augmenter la distance entre l quipement et le r cepteur e Brancher l quipement sur un autre circuit que celui utilis par le r cepteur e Demander l aide du marchand ou
25. een Two kinds of flicker occur line flicker caused by the electron beam scanning in each line of the picture and frame flicker or field flicker if the picture is interlaced caused by the frame repetition rate of 50 frames second Frame flicker is noticeable with GUI and DTP software which have a light background and can be very disturbing especially for those who work regularly with displays contributing to eye strain headaches visual blurring stress etc The problem can however be eliminated by increasing the refresh rate number of frames second of the monitor to a value above around 70 Hz Sensitivity to flicker appears to diminish with increasing age RETURN TO TOP OF THE PAGE H Hertz The unit of frequency named after the physicist Heinrich Hertz 1857 1894 1 hertz Hz is equal to 1 cycle second Horizontal dot pitch See Dot pitch Horizontal scanning frequency file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 6 of 18 2003 3 27 10 39 52 Glossary Also called line frequency and expressed in kHz it is the number of video lines written on the screen every second from left to right The higher the horizontal scanning frequency the better the resolution i e the higher the resolution and or the higher the refresh rate RETURN TO TOP OF THE PAGE INF File INF file Information File Information INF files store information in a specific format The set up functions retrieve informatio
26. electronic user s manual PHILIPS Philips home Safety and trouble shooting About this manual Product information wu Installing your m nitor namen Customer care and warranty FAQ Glossary Download amp print EXIT file D EDFU LF3 lf8manual english 105E manual html 2003 3 27 10 39 26 Safety amp Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance Troubleshooting Regulatory Information Other Related Information Safety precautions and maintenance specified in this documentation may result in exposure to shock electrical WARNING Use of controls adjustments or procedures other than those hazards and or mechanical hazards Read and follow these instructions when connecting and using your computer monitor e Disconnect the monitor from the power supply if the monitor is not to be used for an extended period of time e Do not attempt to remove the back cover as you will be exposed to a shock hazard The back cover should only be removed by qualified service personnel e Do not place objects on top of the monitor cabinet objects could fall into vents or cover them and prevent proper cooling of the monitor s electronic devices e To avoid the risk of shock or permanent damage to the set do not expose the monitor to rain or excessive moisture e Do not use alcohol or ammonia based liquid to clean the monitor I
27. er document showing that you purchased the product is considered proof of purchase Attach it to this owner s manual and keep both nearby WHAT IS COVERED Warranty coverage begins the day you buy your product For three years thereafter all parts will be repaired or replaced and labor is free After three years from the day of purchase you pay for the replacement or repair of all parts and for all labor charges All parts including repaired and replaced parts are covered only for the original warranty period When the warranty on the original product expires the warranty on all replaced and repaired products and parts also expires WHAT IS EXCLUDED Your warranty does not cover e labor charges for installation or setup of the product adjustment of customer controls on the product and installation or repair of antenna systems outside of the product e product repair and or part replacement because of misuse accident unauthorized repair or other cause not within the control of Philips Consumer Electronics e reception problems caused by signal conditions or cable or antenna systems outside the unit e a product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications e incidental or consequential damages resulting from the product Some states do not allow th
28. eters being saved e Press to recall factory preset mode at second level RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english Install_1 FRONT Front htm 3 of 3 2003 3 27 10 40 35 Pedestal Pedestal Front View Rear View Installing your Base Installing your Pedestal 1 To INSTALL e Slide the pedestal aligning with the holes on the wif side e Then click the back hook into the corresponding hole on the bottom plate of your monitor 2 To UN INSTALL e Lift the back hook from the hole on the bottom plate of your monitor e Slide out the pedestal the opposite direction from when you installed it RETURN TO TOP OF THE PAGE file D EDFU LF3 If3manual english INSTALL_1 mm_pede mm_inst htm 2003 3 27 10 40 46 USB Hub Optional Feature PCUH411 USB Hub Option Front View Rear View Installing your USB Hub Installing your USB Hub Installing on a conventional base 1 Take out the USB hub from the box 2 Take off the USB hub cover 3 Slightly tilt and lift the base of your monitor 4 Attach the USB hub by clipping into the base 5 You can reposition the USB hub along the base to suit your needs RETURN TO TOP OF THE PAGE file D EDFU LF3 If3manual english INSTALL_1 usbhub usb_inst htm 2003 3 27 10 40 46 First Choice Warranty Your International Philips First Choice Warranty Thank you for purchasing this Philips monito
29. f The picture may need degaussing Remove any nearby magnetic objects Face the monitor toward the East for the best picture quality file D EDFU LF3 lf8manual english 105E SAFETY saf_troub htm 1 of 2 2003 3 27 10 40 13 Troubleshooting Missing one or more colors Dim Picture Picture is too large or too small Edges of the picture are not square Picture has a double image Picture is not sharp Unstable Picture Problem with On Screen Display Check the Color Temperature Make sure the monitor cable is properly connected to your computer e Check to see if the monitor cable has bent pins e Adjust the Brightness and Contrast controls Check your video card and it s owner s manual instructions for it may be a non VESA DDC Standard card Adjust the Horizontal and or Vertical Size Adjust the Zoom Adjust the geometry Eliminate the use of a video extension cable and or video switch box Face the monitor toward the East for the best picture quality Check to make sure Moir is switched off Adjust Sync Input Increase your refresh rate Refer to the instructions and troubleshooting information in that chapter For further assistance refer to the Consumer Information Centers list to contact your local Philips distributor RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english 105E SAFETY saf_troub htm 2 of 2 2003 3 27 10 40 13 Regulatory Information Regul
30. f necessary clean with a slightly damp cloth Disconnect the monitor from the power supply before cleaning e When positioning the monitor make sure the power plug and outlet are easily accessible Consult a service technician if the monitor does not operate normally when operating instructions of this manual are followed RETURN TO TOP OF THE PAGE file D EDFU LF3 If3manual english 105E SAFETY SAFETY HTM 2003 3 27 10 39 50 About This Electronic User s Manual About This Electronic User s Manual About This Guide Other Documents You May Need Notational Descriptions About This Guide This electronic user s guide is intended for anyone who uses the Philips Color Monitor It describes the monitor s features setup operation and all other information which is the same exact information described in our printed version The sections are as follows Safety and Troubleshooting Information provides tips and solutions for common problems and other related information you may need About This Electronic User s Manual gives overview of what information are included as well as notation icon descriptions and other documentation you can refer to Product Information gives an overview of the monitor s features and as well as the technical specifications for this monitor Installing Your Monitor describes the initial setup process and gives an overview of how to use the monitor Front Controls provides information on adjus
31. g Troubleshooting Safety Precautions and Maintenance Troubleshooting Regulatory Information Other Related Information Common Problems Having trouble Something not working Before calling for help try these suggestions Having this problem No Picture Power LED not lit No Picture Power LED is yellow No Picture Power LED is green Screen doesn t show when you turn on the monitor No color or intermittent color Color appears blotchy Check these items Make sure the Power cable is plugged into the power outlet and back of the monitor Power button on the front of your monitor should be in the ON position Disconnect the monitor from the power outlet for about one minute Make sure the computer is turned on Make sure the monitor cable is properly connected to your computer Check to see if the monitor cable has bent pins The Energy Saving feature may be activated Make sure the Brightness and Contrast controls are set correctly Make sure the monitor cable is properly connected to your computer Check to see if the monitor cable has bent pins e Make sure the computer Power button is on e Make sure the monitor cable is properly connected to your computer Also refer to the Quick Start Guide Check to see if the monitor cable has bent pins e Make sure the computer is turned on e f you are using a non VESA DDC standard video card turn the DDC1 2B feature Of
32. gonomic requirement for Visual Display 1S013406 2 Ergonomic requirement for Flat panels GS EK1 2000 GS specification prEN50279 1998 Low Frequency Electric and Magnetic fields for Visual Display MPR II MPR 1990 8 1990 10 Low Frequency Electric and Magnetic fields TCO95 TCO99 TCOOS Requirement for Environment Labelling of Ergonomics Energy Ecology and Emission TCO Swedish Confederation of Professional Employees for TCO versions RETURN TO TOP OF THE PAGE Energy Star Declaration PHILIPS 105E1 file D EDFU LF3 If3manual english 105E SAFETY regs regulat htm 1 of 9 2003 83 27 10 40 14 Regulatory Information This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling DPMS standard This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299 94 Time settings are adjusted from the system unit by software NUTEK VESA State LED Indicator Power Consumption Normal operation ON Green lt 65 W Power Saving Alternative2 OFF Yellow lt 8W One Step As an ENERGY STAR Partner PHILIPS has determined that this product meets the ENERGY STAR guidelines for energy efficiency A We recommend you switch off the monitor when it is not in use for quite a long time RETURN TO TOP OF THE PAGE Federal Communications Commission FCC Notice U S Only This equipmen
33. h FAQ HTM 2 of 12 2003 3 27 10 39 51 Frequently Asked Questions Energy Saving MPRII No requirement TCO92 Standby mode 30W Off mode 8W TCO95 Standby mode 30W Off mode 8W TCO99 Standby mode 15W Off mode 5W TCO 03 Standby mode 15W Off mode 5W Visual Ergonomics MPRII No requirement TCO92 No requirement TCO95 Set ergonomic rules including minimum contrast level flicker and jitter TCO99 Tightened TCO95 rules TCO 03 Tighten TCO99 rule for CRT and new requirement of screen color for TFT LCD Monitors Ecology MPRII No requirement TCO92 No requirement TCO95 Set general ecological standards including recycling preparation environmental policy and environmental certification TCO99 Further tightened TCO95 norms TCO 03 Require the recycling information to users 10 How do I enable the energy saving function Go to My Computer and select Control Panel followed by Monitor Control Select All default selection and choose your Philips monitor model from the default driver list Plug and Play will automatically enable the EPA tick box for you In DOS or Windows 3 1 you must first make sure your PC supports power saving 11 Whatis refresh rate Refresh rate describes the number of times an entire screen is vertically scanned each second In other words If a monitor s refresh rate is 85 Hz its screen is refreshed or vertically scanned 85 times per second A hig
34. h the LightFrame M hardware equipped monitor and system software the LightFrame does not function 23 What is XtraSpace Design XSD XSD stands for XtraSpace Design a Philips breakthrough that reduces a CHT display device s footprint Philips XSD monitors combine the world s smallest front to back footprint with excellent front of screen performance 24 How did Philips achieve XtraSpace Design Philips achieved this breakthrough in reduced footprint CRT display devices through short depth tubes and a focused design process that squeezed every excess millimeter out of XSD monitor desk space requirements 25 What is Philips monitors solution for audio Not all users need multimedia capabilities To give users freedom of choice Philips provides an optional Multimedia Base type number 6G3B10 The Multimedia Base replaces the easily file D EDFU LF3 lf8manual english FAQ HTM 6 of 12 2003 3 27 10 39 51 Frequently Asked Questions removable standard pedestal of the monitor 26 Which models can be incorporated with the Multimedia Base The following models can be incorporated with the Multimedia Base 109B5 109S5 107B5 107E5 107F5 10785 107T5 27 What are Philips Multimedia Base s specifications See detailed Multimedia Base specifications on the product information page 28 Why is a Multimedia Base better than separate speakers The major advantage of the Multimedia Base is its minimal space requireme
35. her the refresh rate means better image stability and less flicker A high refresh rate helps users who work long hours in front of a monitor avoid eye fatigue and stress To change the refresh rate go into Start Settings Control Pannel Display file D EDFU LF3 lf8manual english FAQ HTM 3 of 12 2003 3 27 10 39 51 Frequently Asked Questions Properties Setting Advance Adaptor Windows settings of the computer the monitor will automatically adjust itself to the video card 12 Why does the picture on the screen appear to flicker A low refresh rate or electrical interference typically causes flickering in the picture Possible solutions include the following e Verify that the proper drivers are installed for your video card e Make sure that all electrical devices such as mobile phones are at least 1m from the monitor e Place the monitor in another physical location away from electrical interference e Adjust the refresh rate to 75hz or higher 13 How do I adjust my monitor s resolution Available resolutions are determined by the capabilities of your video card and graphic driver Under Windows 95 you may select the desired available resolution through the Display properties Settings menu 14 How can I adjust the size position and rotation of my screen Depending on the model you own you can use your CustoMax Software On Screen Display OSD or control knobs located on the monitor 15 What if I get lo
36. hilips feature designed to preserve the life of your monitor Please allow 5 seconds between powering off and on your monitor your picture will then be restored file D EDFU LF3 If38manual english FAQ HTM 12 of 12 2003 83 27 10 39 51 Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ A Autoscan A microprocessor based feature of Philips Brilliance monitors is able to detect automatically horizontal and vertical frequencies of input signals with those of the installed video card An autoscan monitor can thus operate with a wide range of video cards MultiSync a registered trademark of NEC provides a similar function RETURN TO TOP OF THE PAGE Balanced pincushion See Geometric distortion BNC connection A special construction of connector used in some monitors with higher horizontal scanning frequency The BNC connection can provide the optimum shielding and matching characteristic impedance of video signal path to ensure the best video performance nen RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 1 of 18 2003 3 27 10 39 52 Glossary C CE Mark CE mark is displayed on products per EMC and LV low Voltage Device directives in compliance with European Community safety EMI and EMS requirements and is compulsory on products for sale in the European Community Color temperature A way of describing the color of a radiating source in terms of the
37. ions which your dealer cannot answer or any related question please contact the Philips Consumer Information Centers or via Website http www philips com file D EDFU LF3 If3manual english WARRANT Y war intl htm 2003 3 27 10 40 57 United States Guarantee LIMITED WARRANTY Computer Monitor Click here to access the Warranty Registration Card One Year Exchange Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year WHO IS COVERED You must have proof of purchase to receive warranty service A sales receipt or other document showing that you purchased the product as new is considered proof of purchase WHAT IS COVERED Warranty coverage begins the day you buy your product For one year thereafter all parts will be repaired or replaced and labor is free All parts including repaired and replaced parts are covered only for the original warranty period When the warranty on the original product expires the warranty on all replaced and repaired products and parts also expires WHAT IS EXCLUDED Your warranty does not cover e labor charges for installation or setup of the product adjustment of customer controls on the product and installation or repair of systems outside of the product e product repair and or part replacement because of misuse accident unauthorized repair or other cause not within the control of Philips Consumer Electronics
38. irmed LightFrame does not adversely affect monitor life Today s state of the art Philips monitors employ improved phosphors and are designed for high light output LightFrame normally highlights photos and videos Though the peak brightness of the highlighted area is strongly increased the average brightness a determining factor for cathode deterioration is not normally increased In any case a special Automatic Beam Limiter ABL circuit keeps a monitor s maximum average brightness within acceptable levels 21 I get a message warning that my monitor may not support LightFrame am certain my monitor does What is wrong file D EDFU LF3 lf8manual english FAQ HTM 5 of 12 2003 3 27 10 39 51 Frequently Asked Questions Only a Philips driver can determine if your monitor is equipped with LightFrame a generic Windows driver cannot Install the special Philips driver that came with your monitor If the warning continues to flash after your Philips driver is installed ignore the message LightFrameTM will function properly 22 What will happen when my system is no longer connected to a LightFrame enabled monitor for example when I take my notebook on the road Philips exclusive LightFrame feature requires the combined operation of hardware that resides in your monitor and software installed on your system It only works when a monitor with built in hardware receives commands from system software Without bot
39. low speed The hub isolates low speed ports from full speed file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 15 of 18 2003 83 27 10 39 52 Glossary signaling A hub consists of two portions the Hub Controller and Hub Repeater The repeater is a protocol controlled switch between the upstream port and downstream ports It also has hardware support for reset and suspend resume signaling The controller provides the interface registers to allow communication to from the host Hub specific status and control commands permit the host to configure a hub and to monitor and control its ports Device A logical or physical entity that performs a function The actual entity described depends on the context of the reference At the lowest level device may refer to a single hardware component as in a memory device At a higher level it may refer to a collection of hardware components that perform a particular function such as a Universal Serial Bus interface device At an even higher level device may refer to the function performed by an entity attached to the Universal Serial Bus for example a data FAX modem device Devices may be physical electrical addressable and logical Port Port 2 Sen H U B Port Port H4 3 Downstream The direction of data flow from the host or away from the host A downstream port is the port on a hub electrically farthest from the host that generates downstream data traffic from the
40. luding implied warranties of merchantability and fitness for a particular purpose are limited in duration to the duration of this express warranty But because some states do not allow limitations on how long an implied warranty may last this limitation may not apply to you TO GET WARRANTY SERVICE IN CANADA Please contact Philips at 800 479 6696 Three years free parts and three years free labor will be provided at Philips Canada depot or any one of its authorized service centers In Canada this warranty is given in lieu of all other warranties No other warranties are expressed or implied including any implied warranties of merchantability or fitness for a particular purpose Philips is not liable under any circumstances for any direct indirect special incidental or consequential damages howsoever incurred even if notified of the possibility of such damages REMEMBER Please record the model and serial numbers found on the product below MODEL SERIAL This warranty gives you specific legal rights You may have other rights which vary from state province to state province file DI EDFU LF3 f3manual english WARRANTY WAR_USAHTM 2 of 3 2003 3 27 10 40 58 United States Guarantee Philips Customer Care Center P O Box 2976 Longview TX 75601 Your International Philips First Choice Warranty Thank you for purchasing this Philips monitor All Philips monitors are designed and manufactured to high stan
41. n from the INF file to use when performing installation operations Examples of the type of information stored in an INF file include INI and registry changes file names and locations of the source files on source media Interlaced non interlaced Interlaced The method of writing a picture on the screen by initially writing all even lines and subsequently writing all odd lines of the picture Result The complete picture is composed of two interlaced half pictures or fields With interlacing a vertical or field frequency of 50 Hz means a picture or frame frequency of 25 Hz Non interlaced The method of writing a picture on the screen by successive video lines of the picture so that a full frame is written onto the screen in one vertical sweep of the beams With a non interlaced display a vertical frequency of 50 Hz means a picture or frame frequency of 50 Hz At any given resolution non interlaced modes are preferable to interlaced modes however generation of non interlaced modes is more expensive line number interlaced non interlaced RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 7 of 18 2003 3 27 10 39 52 Glossary L Linearity The degree to measure the actual location of a pixel on the screen corresponds with its intended location see figure intended raster horizontal linearity vertical linearity distortion distortion Line frequency See Horizontal
42. ne printer two Com port devices usually a mouse and modem one Enhanced Parallel Port add on scanner or video camera for example and a joystick More and more peripherals for multimedia computers come on the market every day With USB up to 127 devices can run simultaneously on a computer e USB permits hot plug in No need to shut down plug in reboot and run set up to install peripherals No need to go through the reverse process to unplug a device Bottom line USB transforms today s Plug and Pray into true Plug and Play 3 What is a USB hub Think of USB hub as a extension of USB ports Normally the PC provides only one or two USB ports To connect additional USB devices you need a USB hub 4 What is Philips Monitors USB hub solution Increasingly monitors include USB hub functionality But not all users need or want a USB hub To give users freedom of choice Philips provides an optional USB hub type number PCUH411 The USB hub consists of two parts that are normally connected one is functional the other aesthetic The aesthetic element is a removable cover With the cover removed the USB hub can be attached to the base or pedestal of monitor The attached USB hub can be rotated to any position around the monitor s base With this innovative Philips solution your USB hub is always within reach for convenient connection and disconnection of USB peripherals 5 Where can I buy a USB hub for my Philips monitor Philip
43. ned and manufactured to high standards and deliver high quality performance ease of use and ease of installation Should you encounter any difficulties while installing or using this product please contact Philips directly to benefit from your Philips First Choice Warranty This one year service warranty entitles you to a swap model on site within 48 hours of your call being received within the first year of purchase If you have any problems with your monitor within the second or third year of purchase we will repair it after it has been sent to the service provider at your expense and returned to you within five working days free of charge An extended warranty called Philips Flrst Choice Premium is available in addition to your Philips First Choice warranty For more details contact your Philips dealer Before contacting Philips please prepare the following details so we can solve your problem quickly Philips type number Philips serial number Purchase date copy of purchase may be required PC environment Processor o 286 386 486 Pentium Pro Internal memory O Operating system Windows DOS OS 2 MAC o Fax Modem Internet program e Other cards installed Having the following information available will also help speed up the process e Your proof of purchase indicating date of purchase dealer name model and product serial number e The full address to which the swap model should be delivered Philips warranty applies provided the
44. nts In fact it hardly uses any extra space at all monitor depth and width are unchanged Only the monitor s height is increased by only 3 centimeters 29 Where can I buy a multimedia base to incorporate with my Philips monitor Please contact your dealer reseller for details 30 What does Auto Calibrate do It makes your monitor perform better and last longer As a monitor becomes older brightness gradually deteriorates and its colors change This well known process effects all monitors Eventually after a number of years the monitor s brightness deteriorates to below 50 of its original value At this stage the usable life of a monitor is considered ended Auto Calibrate regularly readjusts color temperature and luminance to their original values 31 How does Philips Auto Calibrate feature benefit me file D EDFU LF3 If8manual english FAQ HTM 7 of 12 2003 3 27 10 39 51 Frequently Asked Questions With Auto Calibrate it takes a monitor s luminance 33 percent longer to deteriorate to the 50 percent level that marks the end of a display device s useful life Thanks to Auto Calibrate a monitor with a normal life of 10 000 hours for example would last for 13 300 hours a full one third longer 32 How does Auto Calibrate work During the calibration process different predefined black and white images are displayed on thescreen The beam currents of the red green and blue cannon are accurately measured and compared
45. oclo System kompulerowy nale y zabezpieczy przed nag ymi chwilowymi wzrostami lub spad kami napeect u ywij c eliminalara przepi urz dzenia doepasawujacegi lub kerrakbicendpwega zr d a zasilania Nale y upewni si aby nic nie le a o na kablach systema kotrpaler w ogi araz aby kable nie byly umieszczone w milejscu gdzie moana byloby na nie nadeptywa lub pozyka ale o ide Mie nale y rozlewa napokra aimi zn ych p yn w ma syste kormpulberawey Nie nale y wpycha Mmadnych preze mis w da atoe raw system komputerowej piyi mo e ter spowodowa po ar lub pora enie pr dem paprzez zwarcie elementa wewn trznych Syston kontqnierowy powitien znajdowa si z dala ed grzejnik w i r de ciepla Par zdta nie nale y hlakeoma atwordw wentylacyjnych Nale y unika k adzenia luznych papserira pol kom puber uraz umieszczania kampulera w ciasnym miejscu ber me liwa ci cyrkulacji piwi eza wok miese RETURN TO TOP OF THE PAGE North Europe Information Nordic Countries Placering Ventilation VARNING FORSAKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG AR LATATKOMLIGA NAR DU STALLER DIN UTRUSTNING PAPLATS Placering Ventilation ADVARSEL S RG VED PLACERINGEN FOR AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGAENGELIGE file D EDFU LF3 If3manual english 105E SAFETY regs regulat htm 6 of 9 2003 3 27 10 40 14 Regulatory Information Paikka llmankierto VAROITUS SIJOITA
46. of a picture tube at switch on to minimize picture distortion This is usually accomplished by means of a special degaussing coil through which a decaying alternating current is passed to generate an alternating magnetic field that gradually decays to demagnetize the tube Some monitors offer a manual degaussing facility that can be activated at any time Digital control Microprocessor based digital control of picture parameters and video modes for complete control of picture settings and modes and instant recall of all settings at the push of a button This is a very advanced feature that allows the user to switch to any required mode at any instant without having to spend time readjusting the picture It is currently available in most Philips monitors Dot pitch The shortest distance between two phosphor dots of the same color on the screen The smaller the dot pitch the better the resolution of the monitor file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 4 of 18 2003 3 27 10 39 52 Glossary horizontal te dot pitch Dot rate Frequency in MHz of the dot clock It is a measure of the speed with which data is transferred between the video card and subsequent processing circuitry Also known as video dot rate RETURN TO TOP OF THE PAGE E Electromagnetic radiation standards International standards set to limit electromagnetic emissions from monitors There are currently two important standa
47. om port devices usually a mouse and modem one Enhanced Parallel Port add on scanner or video camera for example and a joystick More and more peripherals for multimedia computers arrive on the market every day With USB up to 127 devices can run simultaneously on a computer e USB permits hot plug in There s no need to shut down plug in reboot and run set up to install peripherals And no need to go through the reverse process to unplug a device In short USB transforms today s Plug and Pray into true Plug and Play Hub A Universal Serial Bus device that provides additional connections to the Universal Serial Bus Hubs are a key element in the plug and play architecture of USB The Figure shows a typical hub Hubs serve to simplify USB connectivity from the user s perspective and provide robustness at low cost and complexity Hubs are wiring concentrators and enable the multiple attachment characteristics of USB Attachment points are referred to as ports Each hub converts a single attachment point into multiple attachment points The architecture supports concatenation of multiple hubs The upstream port of a hub connects the hub towards the host Each of the other downstream ports of a hub allows connection to another hub or function Hubs can detect attach and detach at each downstream port and enable the distribution of power to downstream devices Each downstream port can be individually enabled and configured at either full or
48. orldwide You can contact Philips Monday Friday from 08 00 20 00 hrs Central European Time CET and on Saturdays and Sundays from 10 00 to 18 00 hrs CET by using one of the toll free numbers Click here to access the F1rst Choice Contact Information Or you can reach us via Website http www philips com file D EDFU LF3 If3manual english WARRANTY WAR USA HTM 3 of 3 2003 3 27 10 40 58
49. pain United Kingdom EASTERN EUROPE Czech Republic Hungary Poland Russia Turkey Bulgaria LATIN AMERICA Antilles Argentina Brazil e Chile Colombia Mexico Paraguay Peru Uruguay Venezuela NORTH AMERICA USA amp Canada 107E X only USA 8 Canada all other models PACIFIC Australia New Zealand ASIA Bangladesh China Hong Kong India Indonesia Japan Korea Malaysia Pakistan Philippines Singapore Taiwan Thailand AFRICA Morocco South Africa MIDDLE EAST Dubai Egypt file D EDFU LF3 lf8manual english WARRANTY WARRANTY HTM 2003 3 27 10 39 51 Frequently Asked Questions Frequently Asked Questions 1 What does the Designed for Windows logo signify The Designed for Windows logo means your Philips monitor fulfills the requirements and recommendations of the PC9x 97 98 or 99 System Design Guide and passes stringent WHQL tests 2 What is USB Think of USB as a smart plug for PC peripherals USB automatically determines resources like driver software and bus bandwidth required by peripherals USB makes necessary resources available without user intervention Its three main benefits are e USB eliminates Case angst the fear of removing the computer case to install circuit board cards that often require adjustment of complicated IRQ settings for add on peripherals e USB does away with port gridlock Without USB PCs are normally limited to o
50. parate sync Horizontal and Vertical sync signals transmitted separately 2 Composite sync Horizontal and vertical sync pulses mixed into a single signal train 3 SOG Horizontal and vertical sync pulses mixed then combined with the green color signal RETURN TO TOP OF THE PAGE T TCO See Electromagnetic radiation standards Tilt function file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 14 of 18 2003 83 27 10 39 52 Glossary See rotation function Trapezoid distortion See Geometrical distortion TTL signal A TTL Transistor transistor logic signal is a digital signal level for controlling the screen colors With TTL driving the red green and blue signals can only be switched on or off or provided with an intensity signal A TTL driven monitor can thus display a maximum of 64 colors Video standards such as MDA CGA and EGA are based on TTL level RETURN TO TOP OF THE PAGE U USB or Universal Serial Bus A smart plug for PC peripherals USB automatically determines resources like driver software and bus bandwidth required by peripherals USB makes necessary resources available without user intervention e USB eliminates case angst the fear of removing the computer case to install add on peripherals And USB also eliminates adjustment of complicated IRQ settings when installing new peripherals e USB does away with port gridlock Without USB PCs are normally limited to one printer two C
51. product is handled properly for its intended use Philips warranty will not apply if it appears during the repair process that the reported failure is caused by improper handling or accidents the monitor is not defective and is within the specification the monitor has been altered or repaired by non authorised persons If warranty claims are determined to be invalid Philips may invoice the customer for all related repair verification and transportation costs Just a phone call away Philips customer help desks are located worldwide You can contact Philips Monday Friday from 08 00 20 00 hrs Central European Time CET and on Saturdays and Sundays from 10 00 to 18 00 hrs CET by using one of the toll free numbers Click here to access the Flrst Choice Contact Information Or you can reach us via Website http www philips com file D EDFU LF3 lf38manual english WARRANTY 7sxWAR_USA HTM 3 of 3 2003 3 27 10 40 58 United States Guarantee LIMITED WARRANTY Computer Monitor Click here to access the Warranty Registration Card Three Years Free Labor Three Years Free Service on Parts One Year Exchange Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year This product must be shipped in at your expense for service during years two and three WHO IS COVERED You must have proof of purchase to receive warranty service A sales receipt or oth
52. quipment the power supply cable must be removed from the power supply socket which should be located near the equipment and easily accessible A protection mark B confirms that the equipment is in compliance with the protection usage requirements of standards PN 93 T 42107 and PN 89 E 06251 file D EDFU LF3 lf8manual english 105E SAFETY regs regulat htm 5 of 9 2003 83 27 10 40 14 Regulatory Information Wymagania Polskiego Centrum Badan i Certyfikacji Urz dzenie powinno by zasilane z gniazda z przyt czaym obwodem ochronny gniazda z ka kieniy Wsp pracuj ce ze sob urz dzenia komputer monitor drukarka powimiy by zxsilame zego samego rada Instalacja elektryczna pomieszczenia powinna zawiera w przewadzie fasoerym rererwaw achrang przed zwarc ami w postaci bezpeecenika o warto ci znamionowej nie wi kszej ni 164 amperi W celu ca kowitego wy czenia urz dzenia z sieci zasilania nale y wyj wtyczk kabla zasilaj cego z gidazdka kt re pawiana ziajdewa aig w pobli u urz dzenia s byt atwa dost pie Znak bespierzeisrwa B potwierdza zgodno urz dzenia wymaganiami bezpiecze stwa u ytkowania zawarty w PAAGT 10T 1 PAGE AIS Pozosta e instrukcje bezpiecze stwa Mie nale y u ywa wryczek adapierowych lub usuwa kolka obwodu ochronnego z wtyczki Je eli konseczne jest u ycie pezedla acza bo nale y u y przeddu acza 3 7ylowega 2 prawidbowa pa czar ym przewodem
53. r All Philips monitors are designed and manufactured to high standards and deliver high quality performance ease of use and ease of installation Should you encounter any difficulties while installing or using this product please contact Philips directly to benefit from your Philips F1rst Choice Warranty This three year service warranty entitles you to a swap model on site within 48 hours of your call being received An extended warranty called Philips First Choice Premium is available in addition to your Philips First Choice warranty For more details contact your Philips dealer Before contacting Philips please prepare the following details so we can solve your problem quickly e Philips type number e Philips serial number e Purchase date copy of purchase may be required e PC environment Processor O 286 386 486 Pentium Pro Internal memory O Operating system Windows DOS OS 2 MAC o Fax Modem Internet program e Other cards installed Having the following information available will also help speed up the process e Your proof of purchase indicating date of purchase dealer name model and product serial number e The full address to which the swap model should be delivered Philips warranty applies provided the product is handled properly for its intended use Philips warranty will not apply if it appears during the repair process that the reported failure is caused by improper handling or accidents the monitor is not defec
54. rating instructions and upon presentation of the original invoice or cash receipt indicating the date of purchase dealer s name and model and production number of the product The Philips guarantee may not apply if e the documents have been altered in any way or made illegible e the model or production number on the product has been altered deleted removed or made illegible e repairs or product modifications and alterations have been executed by unauthorized service organizations or persons e damage is caused by accidents including but not limited to lightning water or fire misuse or neglect Please note that the product is not defective under this guarantee in the case where modifications become necessary in order for the product to comply with local or national technical standards which apply in countries for which the product was not originally designed and or manufactured Therefore always check whether a product can be used in a specific country In case your Philips product is not working correctly or is defective please contact your Philips dealer In the event you require service whilst in another country a dealer address can be given to you by the Philips Consumer Help Desk in that country the telephone and fax number of which can be found in the relevant part of this booklet In order to avoid unnecessary inconvenience we advise you to read the operating instructions carefully before contacting your dealer If you have quest
55. rds both derived from regulations originally laid down by Swedish authorities MPR II The standard originally proposed by the Swedish National Board of Measurement and Testing It set maximum levels of electromagnetic radiation emitted by monitors and has now been adopted as a world standard MPR II defines maximum permitted electrostatic magnetic and electric field levels measured at a distance of 50 cm from the center of the monitor see table TCO file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 5 of 18 2003 3 27 10 39 52 Glossary In 1991 the Swedish Tj nstemannens Central Organization TCO Swedish confederation of Professional Employees set a standard even more severe than MPR II especially for alternating electric fields AEF The TCO standard is more severe since not only are the permitted field levels reduced compared with MPR II but the measuring distance is also reduced see table Electromagnetic radiation standards EMI Electrical Magnetic Interference The electrical and or magnetic radiation coming from the working electrical or electronic equipment EMS Electrical Magnetic Sustainment The ability of electrical or electronic equipment to function properly in the environment with electrical and or magnetic interference RETURN TO TOP OF THE PAGE F Flicker Very rapid variations in picture intensity caused by the finite time required for the electron beam to scan a picture onto the scr
56. re P22 medium short persistence phosphor and EBU high color saturation phosphor Pin cushion Distortion See Geometric distortion Pixel Abbreviation for picture element the smallest element of the picture that can be displayed on the screen The smaller the pixel size the better the resolution of the monitor Pixel size is determined by the size of the electron spot on the screen and not necessarily by the phosphor dot pitch the size of the triad Thus a monitor with a large electron spot covering several triads can exhibit poor resolution even though its dot pitch is small Pixel frequency The number of pixels that can be written in a video line per second Pixel rate See pixel frequency Plug and Play See DDC See USB section RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 10 of 18 2003 83 27 10 39 52 Glossary R Haster The area on screen that electron beam can reach Refresh rate See Vertical scanning frequency Hesolution The number of pixels that can be displayed on the screen The resolution is specified as the number of pixels in a line multiplied by the number of horizontal lines See also video graphic adapter Rotation function The feature that allows users to adjust the whole screen rotating to be horizontal Because of the magnetic field of earth the screen of monitor will be tilt when the screen faces toward the different direction RETUR
57. s in the mains lead are coloured in accordance with the following code BLUE i NEUTRAL N BROWN _ LIVE LE GREEN amp YELLOW EARTH E 1 The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN AND YELLOW 2 he BLUE wire must be connected to the terminal which is marked with the letter N or coloured BLACK 3 The BROWN wire must be connected to the terminal which marked with the letter L or coloured RED Before replacing the plug cover make certain that the cord grip is clamped over the sheath of the lead not simply over the three wires RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english 105E SAFETY regs regulat htm 9 of 9 2003 83 27 10 40 14 Other Related Information Other Related Information Safety Precautions and Maintenance Troubleshooting Regulatory Information Information for Users in the U S Information for Users Outside the U S Information for Users in the U S For units set at 115 V Use a UL Listed Cord Set consisting of a minimum 18 AWG Type SVT or SJT three conductor cord a maximum of 15 feet long and a parallel blade grounding type attachment plug rated 15 A 125 V For units set at 230 V Use a UL Listed Cord Set consisting of a minimum 18 AWG Type SVT or SJT three conductor cord a maximum of 15 feet long and a tandem blade groun
58. s provides an optional USB hub type number PCUH411 which can be attached to the file D EDFU LF3 lf8manual english FAQ HTM 1 of 12 2003 3 27 10 39 51 Frequently Asked Questions base or pedestal of Philips monitors Contact your dealer reseller for details 6 What models are Mac compatible All listed Philips monitors are Mac compatible BUT you may need an adapter to connect the monitor to your Mac system Please contact your dealer reseller for details T What is TCO TCO is a Swedish abbreviation for the Swedish Confederation of Professional Employees 8 What is MPR MPR is a Swedish abbreviation for the Swedish National Board of Measurement and Testing 9 What are the differences between MPRII TCO92 TCO95 TCO99 and TCO 03 In the general hierarchy of standards TCO 03 TCO99 is the highest level of certification Next is TCO95 which is better than TCO92 which in turn is better than MPRII Below we compare the standards in each category CO 92 Phase out June 30 2000 CO 95 Will be end December 31 2003 Emissions MPRII Set low emission rules for visual displays TCO92 Imposed more stringent standards than MPHII TCO95 Further toughened TCO92 rules TCO99 Delineated even more severe standards and test procedures than TCO95 TCO 03 Same as TCO99 standard Testing uncertainty Safety MPRII No requirement TCO92 95 99 03 All set requirements file D EDFU LF3 lf8manual englis
59. scanning frequency Low emission monitor A monitor that complies with international standards on radiation See Electromagnetic radiation standards Low frequency electric and magnetic fields Alternating fields generated by the deflection yoke These are subject to increasing attention notably by governing authorities the trade and the press Although there is no scientific evidence that monitor emissions are harmful much effort has gone into reducing emissions on the principle of better safe than sorry Currently there are two areas of interest very low frequency VLF electric and magnetic fields extending from 2 kHz to 400 kHz and extreme low frequency ELF fields extending from 5 Hz to 2 kHz See also Electromagnetic radiation standards RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english GLOSSARY GLOSSARY HTM 8 of 18 2003 3 27 10 39 52 Glossary M Moir effect A fringe pattern arising from the interference between two superimposed line patterns In a monitor it comes from the interference between the shadow mask pattern and the video information video moir and between the shadow mask pattern and the horizontal line pattern scan moir It shows itself as wavy patterns on the screen and becomes more noticeable as monitor resolution increases Since the video signal varies continuously little can be done about video moir Scan moir depends on the horizontal scanning frequency and can be alleviate
60. st when making monitor adjustments Simply press OK button then select Reset to factory settings to restore all settings 16 What is LightFrame LightFrame is a Philips technology breakthrough which offers a unique and revolutionary solution for boosting a monitor s brightness and sharpness With LightFrameTM the user experiences TV quality performance for video or photos without deterioration to the monitor s file D EDFU LF3 lf8manual english FAQ HTM 4 of 12 2003 3 27 10 39 51 Frequently Asked Questions performance in windows used for other applications 17 How does LightFrame work LightFrame consists of a software application and an Integrated Circuit IC embedded in the monitor Together they boost brightness and sharpness in a user defined window or screen area Unique LightFrameTM technology dramatically improves photo and video display quality 18 Why is LightFrame important to me With LightFrame selected Philips monitors deliver TV quality video and photo display while maintaining monitor performance for text based applications The result is that movies and other video are brighter and livelier photos are more vibrant and lifelike 19 Will anyone else have this LightFrame was invented developed and patented by Philips It is a unique feature that you will find exclusively in Philips monitors 20 Will LightFrame shorten the life of a monitor No Extensive testing has conf
61. t has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer file D EDFU LF3 lf8manual english 105E SAFETY regs regulat htm 2 of 9 2003 83 27 10 40 14 Regulatory Information device To prevent damag
62. the monitor file D EDFU LF3 If38manual english FAQ HTM 11 of 12 2003 83 27 10 39 51 Frequently Asked Questions e Check that the power button is switched on e Unplug the monitor for approx 1 minute and plug it in again Switch the monitor back on 48 Whyis there no picture on my monitor even though the power LED is yellow amber or flashing green e Reboot your computer while holding the Ctrl key on your computer If you see any picture during the boot procedure please verify the settings of your video card for Windows go to Control Panel and select Display e Check that the video cable is not damaged bent or that any of the pins in the connector are damaged please be aware that some VGA connectors have one missing pin If damaged replace with a new cable e Check that the cable is attached correctly to the computer e Press any key on the keyboard to wake up the computer from power saving mode 49 Whyis there no picture on my monitor even though the power LED is green e Verify the Contrast and Brightness setting of the monitor First press and hold the 5 button to increase Contrast and then press and hold the 4 button to increase Brightness These buttons are located on the front of your monitor e Press both the 5 button and the OK button at the same time to switch input A B e ry and repeat step 48 above 50 Why does the picture disappear after press the on off button quickly This is a unique P
63. ting service Adjustments of the controls discussed there may save you a service call TO GET WARRANTY SERVICE IN U S A PUERTO RICO OR U S VIRGIN ISLANDS Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for servicing Philips Customer Care Center 877 835 1838 or 903 242 4804 In U S A Puerto Rico and U S Virgin Islands all implied warranties including implied warranties of merchantability and fitness for a particular purpose are limited in duration to the duration of this express warranty But because some states do not allow limitations on how long an implied warranty may last this limitation may not apply to you TO GET WARRANTY SERVICE IN CANADA Please contact Philips at 800 479 6696 One year free parts and one year free labor will be provided at Philips Canada depot or any one of its authorized service centers REMEMBER Please record the model and serial numbers found on the product below MODEL SERIAL This warranty gives you specific legal rights You may have other rights which vary from state province to state province Philips Customer Care Center P O Box 2976 Longview TX 75601 Your International Philips First Choice Warranty Thank you for purchasing this Philips monitor file D EDFU LF3 If38manual english WARRANTY 7sxWAR_USA HTM 2 of 3 2003 3 27 10 40 58 United States Guarantee All Philips monitors are desig
64. ting the settings on your monitor Customer Care and Warranty is a list of worldwide Philips consumer information centers along with the help desk phone numbers and information on the applicable warranty of your product e Glossary provides more information for technical terms e Download allows users to install the entire manual on their hard drive e Frequently Asked Questions provides answers to commonly asked questions RETURN TO TOP OF THE PAGE Other Documents You May Need In addition to this Electronic User s Guide you may need to refer to the following documentation Philips Color Monitor Quick Start Guide which summarizes the steps for setting up the monitor This is included with this product RETURN TO TOP OF THE PAGE file D EDFU LF3 lf3manual english 105E ABOUT ABOUT HTM 1 of 2 2003 3 27 10 39 50 About This Electronic User s Manual Notational Descriptions The following subsections describe notational conventions used in this document Notes Cautions and Warnings Throughout this guide blocks of text may be accompanied by an icon and printed in bold type or in italic type These blocks are notes cautions and warnings and they are used as follows NOTE This icon indicates important information and tips that help you make better use of your computer system CAUTION This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data WARNIN
65. tive and is within the specification the monitor has been altered or repaired by non authorised persons If warranty claims are determined to be invalid Philips may invoice the customer for all related repair verification and transportation costs Just a phone call away Philips customer help desks are located worldwide You can contact Philips Monday Friday from 08 00 20 00 hrs Central European Time CET and on Saturdays and Sundays from 10 00 to 18 00 hrs CET by using one of the toll free numbers Click here to access the F1rst Choice Contact Information Or you can reach us via Website http www philips com file D EDFU LF3 If3manual english WARRANT Y war 1st htm 2003 3 27 10 40 57 International Guarantee Your International Guarantee Dear Customer Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards If unfortunately something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase This international Philips guarantee complements the existing national guarantee obligations to you of dealers and Philips in the country of purchase and does not affect your statutory rights as a customer The Philips guarantee applies provided the product is handled properly for its intended use in accordance with its ope
66. to the original values stored in the monitor By readjusting gain values of the individual cannons deviation is reduced to zero Default values are stored during production If the user sets a new color temperature this new value is saved as the new default value 33 When should calibration be performed The calibration process takes less than six seconds During this period different specific images are displayed After the process is finalized the original image is redisplayed Constant re calibration is not required Calibration should be performed after the monitor is warmed up Auto Calibration takes place when a monitor receives a signal indicating an imminent switch to its sleep mode stand by mode 34 Which models of Philips monitors are equipped with Auto Calibrate feature Auto Calibrate is currently available in the new 201P 201B and 109P 35 The Main Menu displays OSD MAIN MENU LOCKED Pressing the front control panels hasno effect How can I unlock this function Press and hold the OSD menu key for about 10 seconds until picture displays OSD MAIN MENU UNLOCKED 36 My screen shows NO SYNC INPUT how can I get rid of this file D EDFU LF3 lf8manual english FAQ HTM 8 of 12 2003 3 27 10 39 51 Frequently Asked Questions Check the following for possible solutions e Bent pins on the video cable e Make sure the computer is turned on e Ensure the VGA Cable is properly connected e Ensure the BNC D Sub connec
67. tor on the rear of the monitor is in the correct position newer models have this option in the On Screen Display under Input Signal Selection Video card may be not a VESA standard try the monitor with another computer 37 Why does my monitor display Out of Range The video card installed in your computer may be too high for the monitor s specifications Please contact your computer manufacturer for details on how to lower resolution for your operating system 38 What is Moire Why does my monitor have this wavy phenomenon Moire is a natural effect or phenomenon of CRT that has the appearance of a wavy pattern which is repetitive and superimposed on the screen as ripple images These are a few suggestions to help reduce or minimize the effects e Some monitors have a Moire cancellation feature activate it to the on position or adjust the Moire cancellation function via the OSD on the monitor e Change resolution to the recommended standard for the specific monitor size e Change Window viewing pattern scheme to a pattern where the Moire is less visible e Change horizontal and vertical size to optimize the reduction of the Moire effect 39 What is CustoMax CustoMax is proprietary Philips software that allows user to control parameter e g Size Color Geometry in place of the buttons on the front of the monitor To install and run the CustoMax software you must have a USB compatible system and have a USB connection at the re
68. video ground 15 Data clock line SCL file D EDFU LF3 lf8manual english 105E PRODUCT PRODUCT HTM 3 of 4 2003 3 27 10 39 51 105E Product Information 8 Blue video ground E RETURN TO TOP OF THE PAGE Views Follow the links to see various views of the monitor and its components Front View Rear View RETURN TO TOP OF THE PAGE file D EDFU LF3 lf8manual english 105E PRODUCT PRODUCT HTM 4 of 4 2003 3 27 10 39 51 Installing your Monitor Installing your Monitor Front View Rear View Pedestal PCUH411 USB Hub option Front View G ecoocs 8 For detailed information about the knobs and keys please refer to Front Controls RETURN TO TOP OF THE PAGE Rear View file D EDFU LF3 lf38manual english INSTALL_1 INSTALL HTM 1 of 2 2003 3 27 10 39 51 Installing your Monitor 1 Power in attach power cable here 2 Video In this is a cable which is already attached to your monitor Connect the other end of the cable to your PC RETURN TO TOP OF THE PAGE file D EDFU LF3 lf38manual english INSTALL_1 INSTALL HTM 2 of 2 2003 3 27 10 39 51 Customer Care and Warranty Customer Care amp Warranty PLEASE SELECT YOUR COUNTRY AREA TO READ THE WARRANTY COVERED WESTERN EUROPE Austria Belgium Cyprus Denmark France Germany Greece Finland Ireland Italy Luxembourg the Netherlands Norway Portugal Sweden Switzerland S
69. zontal position of the image H Size to adjust the horizontal amplitude of the image V Shift to adjust the vertical position of the image V Size to adjust the vertical amplitude of the image Select level of the function pads Trapezoid to correct the trapezoid distortion of the image m Pincushion to correct the barrel distortion of the image Recall to recall original factory preset mode Remarks file D EDFU LF3 lf8manual english Install_1 FRONT Front htm 2 of 3 2003 3 27 10 40 35 Front Controls When pressing any function pad the Shift LED will flash once to indicate the function has been selected 2 Once the limit of the adjustable range has been reached the shift LED will flash continuously RETURN TO TOP OF THE PAGE Adjustment For Tne monitor is pre set with 6 modes for optimal display size and centering as indicated in the following table Horizontal Vertical Mode Resolution Remark EM dotsxlimes TAC UD ECCE VGA 600 X 400 31 5 Non interlaced interlaced VGA 600 X 480 31 5 e Non interlaced VESA 75 600x480 375 Non interlaced VESA 75 600X480 469 78 Nonnferlaced VESA 85 800X600 537 85 Nonnferlaced MESA 1024X768 488 60 Nonnterlaced A User mode 10 modes e The set will save the user s setting parameters automatically After 10 seconds of key pad inactivity the LED will flash twice to indicaate the param

Philips 105E19 Computer Monitor User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents