Jura Capresso 63942R Coffeemaker User Manual
Contents
1. Impressa F9 Fully Automatic Coffee amp Espresso Center with Claris Water Care System Operating Instructions and Warranty Customer Service 1 800 220 5701 63942R IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 Read all instructions 2 Do not touch hot surfaces Use handles or knobs 3 To protect against fire electric shock and personal injury do not immerse cord plugs or appliance in water or other liquids 4 Close supervision is necessary when any appliance is used by or near children 5 Unplug from outlet when not in use and before cleaning Allow it to cool before putting on or taking off parts and before cleaning the appliance 6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment 7 The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or personal injury 8 Do not use outdoors 9 Do not let the cord hang over the edge of a table or counter or touch hot surfaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any control to off then remove p2. 21 19 CARE AND MAINTENANCE ner en 21 a Fil Water 2 een 21 b Empty Tray Empty GroundSs nn 21 C Fil Beans nno lasagne aan 21 d Stones and Beans iii 22 e General Cleaning INStructions nenn 22 f Emptying System Before Transport 22 20 AUTOMATIC CLEANING CYCLES 22 a Cleaning with Special Tablet 22 b Decalcifying Procedure 23 21 Tips for Better Coffee ii 24 22 SUPplieS 0 ein 24 23 LIMITED WARRANTY nennen nennnnennnnnn 24 24 Troubleshooting i 25 Address Informationi iii eu 27 1 PRODUCT REGISTRATION Please read the enclosed product registration form now Fill it out and mail or fax it to us within two weeks after purchasing your machine or register online through our website www capresso com Important This registration is part of your warranty chapter 23 2 CUSTOMER SERVICE Thank you for choosing this Jura Capresso product Please study these operating instructions carefully before using your new machine We highly recommend viewing the enclosed video For further information please call our special TOLL FREE number 1 800 220 5701 Mon Fri 9AM 9PM amp Sat 9AM 5PM Eastern Standard Time If you call at any other time please leave a message with your telephone numbe
3. If you like your coffee extremely hot the Impressa F9 can accommodate you Brew your coffee but reduce the cup size by approx 0Z e g if you plan to brew a 6 oz cup change the cup size in programming to 5 oz 165 ML After brewing your coffee push the Steam Button Fig 4b and wait until the light stops blinking Move the cylinder of the frother up for steaming Fig 18 Now immerse the tip of the frother into your cup Push the Steam Button again and inject steam for about 10 to 20 sec onds Your coffee will be extremely hot 24 Please note Some of the aroma of the coffee will be lost in this process 22 SUPPLIES The following supplies are necessary to keep your machine in good working order e Claris Water Filter Cartridge eliminates the need for decalcifying tablets e Special Cleaning Tablets white tablets e Decalcifying tablets large white square tablets Please note You must use decalcifying tablets if you do not use the Claris cartridge All supplies are available through the enclosed mail order form that came with your machine our toll free line at 1 800 220 5701 or the Internet at www capresso com 23 LIMITED WARRANTY Please note This warranty will be void if the Warranty Product Registration has not been received two weeks after the purchase date you can fax or mail the registration or you can register through our website www capresso com This limited warranty covers your
4. TIME 11 7 Adding Coffee Beans ii 12 8 Adjusting the Grinder nenne nennen nennen nenne 12 9 DAILY PREPARATION nennen nennen 13 10 Grinding and Brewing ii 13 a Selecting Cup Size and Strength 13 11 Using Pre Ground Coffee n 13 12 Using Hot Water 14 13 FROTHING STEAMING HEATING 14 14 Heating and Frothing Milk ii 14 15 Cleaning the Dual Frother Plus nn 15 16 CLARIS WATER CARTRIDGE 15 a Installing and Activating the Claris Cartridge 16 b Replacing the Claris Cartridge 16 17 Adjusting the Water Hardness 17 Table of Contents Page 18 PROGRAMMING 17 a Programming AROMA n 18 b Programming Temperature eneee 18 c Programming Water Quantity Cup Sizes 18 d Programming the 1 Cup Button 19 e Programming Steam Portion nenn 19 f Programming Hot Water Portion 19 g Setting the Time 20 h Setting Auto On TIME i 20 i Setting Auto Shut Off ueessssnnnrsnnnnnennnnernnnnnn nenn 20 j Setting Language iii 21 k Looking Up Cup Counter
5. coffees made e Press the P Button e Touch the right arrow until the display shows SUPPLIED It will show the total number of coffees brewed e Touch any of the cup symbols or coffee buttons and the display shows how often this selection has been used e Press the P button to return to SELECT PRODUCT 19 CARE AND MAINTENANCE 19a FILL WATER When the display shows FILL WATER no more coffee can be made until you fill the water container The water container will never be completely empty The low water floatation device Fig 8 4 activates the FILL WATER indicator when there are about 10 oz of water left e Remove water tank rinse and fill with fresh water and replace 19b EMPTY TRAY EMPTY GROUNDS Used coffee grounds are collected in the used coffee container Fig 2 19 If the display shows EMPTY GROUNDS or EMPTY TRAY no more coffee can be made until you empty the used coffee container e Carefully lift and remove drawer since there is water in it Fig 21 The display shows TRAY MISSING Important Do NOT unplug the machine while you are emptying the coffee grounds e Empty the used coffee container and the drawer e Push the drawer back into the machine Fig 22 The display still shows TRAY MISSING e Place the used coffee container on the tray and insert back into the machine Fig 23 The display shows SELECT PRODUCT and you may now continue brewing coffee 19c FILL BEANS When the display shows FI
6. in duration to the period of the express warranty set forth above and no person is authorized to assume for JURA CAPRESSO any other liability in connection with the sale of the machine JURA CAPRESSO expressly disclaims liability for incidental and consequential damages caused by the machine The terms incidental damages refer to the loss of the original purchasers time loss of the use of the machine or other costs relating to the care and custody of the machine The terms consequential damages refer to the cost of repairing or replacing other property which is damaged when this machine does not work properly Any loss of income is excluded The remedies provided under this warranty are exclusive and in lieu of all others This warranty gives you specific legal rights and you may also have other rights which vary from state to state 24 TROUBLESHOOTING A NO COFFEE COMES OUT OF THE COFFEE SPOUT Reason Beans in bean container are not feeding properly into the grinder because they are stuck together Solution Stir beans before grinding and while grinding turn the grinding selector to the coarsest setting When using very oily beans pour the beans onto a plate and let some of the sticky oils evaporate this will not harm the aroma of the coffee Reason You used ground coffee in the ground coffee funnel The ground coffee was too fine Solution Use ground coffee which is ground somewhat coarser Reason No water is transported thro
7. off e Place a cup underneath the frother e Push and hold the Steam Button until the display shows SYSTEM EMPTYING The machine will push a bit of water and steam into the cup underneath the frother After about 30 seconds it will turn off automatically Important The next time you turn the machine on you must fol low the instructions in chapter 6 Please note Before transporting the machine make sure that the water tank is empty the filter cartridge is removed discard and use a new cartridge the bean container is empty the drawer 22 and used coffee container are empty and clean Secure the lids of the water tank and the bean container with scotch tape Pack entire machine with thick cushioning material on all sides to prevent damage 20 AUTOMATIC CLEANING CYCLES 20a CLEANING WITH SPECIAL TABLET The machine monitors how many coffees are brewed and how often the rinsing program is activated After approx 200 coffees the display will show CLEAN MACHINE SELECT PRODUCT Please note You can continue to make coffee however we highly recommend that you clean the machine as described below within the next few days This cleaning program will remove oil build ups in the brewing chamber This cleaning program takes about 15 minutes Please use one white cleaning tablet enclosed The machine comes with a pack of 2 tablets To re order cleaning tablets see chapter 22 Important Once the cleaning program has started do
8. pour the beans in an open bowl and let them sit for about 5 hours The oils will evaporate this will not change the taste of your coffee Then fill the beans into the bean grinder Now beans will feed into the burrs more easily 8 ADJUSTING THE GRINDER You can adjust the grinder to the roast of your coffee We recommend the following Light roast use a finer adjustment Dark roast use a coarser adjustment e Open the lid of the bean container Fig 1 9 e To adjust grinding turn the selector switch to the desired position Fig 7 The smaller the dots the finer the grind The bigger the dots the coarser the grind Important The grinding grade can only be adjusted while the grinder is actually grinding Attention Oily beans tend to stick together Stir beans just before grinding to ensure a proper flow of beans into the burrs 9 DAILY PREPARATION We recommend filling the water container every morning with fresh cold water This will enhance the taste of your coffee e Push and hold the On Off button until the display turns on After WWW IMPRESSA F LINE COM the display shows HELLO YOUR MACHINE IS HEATING After approx two minutes the display shows PRESS MAINT and the red light in the Rinse Button Fig 3b will illuminate Press the Rinse Button Hot water will warm up all internal parts and pump through the coffee spouts The water will be caught in the drawer underneath The rinse cycle stops by itself and the di
9. rinse all parts and replace The display shows FILL WATER 9 Remove the water tank rinse thoroughly fill with cold fresh water approx 16 oz and replace 10 Place a container at least 16 oz underneath the frother The display shows PRESS MAINT FILL WATER 11 Push the Rinse Button First the machine will pump hot water in intervals through the frother to remove any decalcifying mixture During this procedure the display shows MACHINE DESCALED When the cleaning cycle is finished the machine beeps and the display shows 23 EMPTY TRAY 12 Remove the container from underneath the frother Remove the drawer empty rinse thoroughly and replace The display shows PRESS MAINT 13 Push the Rinse Button The machine will run a regular rinse cycle MACHINE RINSING and then the display will return to its normal position SELECT PRODUCT 14 Clean the chrome front and the grid with a moist soft cloth 21 TIPS FOR BETTER COFFEE Pre warm your cups A warm cup will keep the coffee hot longer Hold your cup underneath the frother and push the Hot Water Button Fig 4a for a few seconds Discard the water into the drawer Move the coffee spout close to the cup This way the coffee will loose less aroma Sugar and cream Cold milk reduces the temperature of your coffee If you like your coffee with cream or with cream and sugar add it to the cup first and steam it for a few seconds Then add the coffee Extremely hot coffee
10. 6c firmly into the steam nozzle the connector should sit flush with the chrome sleeve so that the steam nozzle is no longer visible Please note If the parts are not put together tightly it will not be possible to create the frothy foam on top of the milk 16 CLARIS WATER CARTRIDGE The machine comes with one Claris water cartridge The Claris water cartridge is specially made for use with the Impressa machines The Claris cartridge e Reduces the water hardness up to 75 e Removes if present up to 85 chlorine up to 90 lead up to 95 copper and up to 67 aluminum e Cleans the water through an upward current principle Fig 9 just before the brewing cycle starts ensuring freshly filtered water every time you make coffee e Eliminates decalcifying When using the Claris water cartridge you never need to decalcify your machine e Is available through your retailer the enclosed mail order form or through www capresso com or call 1 800 220 5701 15 16a INSTALLING amp ACTIVATING THE CLARIS WATER CARTRIDGE Important Never install the cartridge before or during the first time preparation of the machine e Make sure the water tank is empty e Remove cartridge from its bag e Open water container lid and pull up the holder for the Claris cartridge Fig 10 e Insert the cartridge with its tapered end down into the water container Make sure it fits snugly inside the fins Push down gently Fig 11 e Close the
11. Follow the instructions in chapter 16a to program the Claris Cartridge function Important The decalcifying program must not be interrupted DECALCIFYING AGENT Only use our special decalcifying tablets For supplies see chapter 22 CAUTION Never use vinegar or any other decalcifying agent This might damage internal parts of the machine 1 Turn off machine and let cool down for at least one hour Empty Water tank 2 With the machine off push and hold the Rinse Button Fig 3b until the display shows EMPTY TRAY 3 Remove and empty the drawer and replace complete assembly Fig 23 Important Even if the drawer is empty you still need to remove it for approx 20 seconds and then replace it The display shows AGENT IN TANK PRESS MAINT 4 Dissolve three of the large square tablets in 16 oz of water and pour this mixture into the water tank Please note Do not use more than 16 oz of water 5 Replace water tank 6 Place a container at least 16 oz underneath the frother The displays still shows AGENT IN TANK PRESS MAINT 7 Push the Rinse Button The machine will pump the mixture through the frother in intervals Then it pumps the mixture internally into the drawer During this procedure the display shows MACHINE DESCALED When this cycle is finished the machine beeps and the display shows EMPTY TRAY 8 Remove the container from underneath the frother Carefully lift and remove the drawer empty and thoroughly
12. LL BEANS open the bean container lid and add beans Fig 6 Please note The message FILL BEANS will disappear after making the next cup of coffee Attention If the display shows FILL BEANS and there are ample beans in the bean container stir the beans so they flow into the grinder chapter 8 We recommend cleaning the bean container from time to time with a dry cloth before you refill beans please make sure the machine is turned off when cleaning 21 19d STONES AND BEANS Every coffee specialty store will tell you that occasionally stones can be found in with coffee beans Small stones will be processed through the burr grinder without any harm the stone will end up in the used coffee container However larger stones can block the burr grinder The noise of the grinder will become very loud and the grinder will block Before Filling Beans into the Bean Container e Shake your bean bag thoroughly so that a stone will fall to the bottom of the bag e Before emptying the bean bag completely check if there are any particles that look like stones and remove them 19e GENERAL CLEANING INSTRUCTIONS Never use abrasive materials or chemicals to clean the machine e Clean the housing with a soft damp cloth e Rinse water tank daily and fill with fresh cold water 19f EMPTYING SYSTEM BEFORE TRANSPORT This procedure is necessary to prevent water and frost damage in case you intend to transport your Impressa F9 e Turn machine
13. T RT symbol until the machine starts grinding Initially the grinding chamber may not fill properly with ground coffee The machine will start brewing then interrupt and the display will show FILL BEANS e Touch and hold ST RT again This time the machine will grind and brew and stop by itself Discard this first cup of coffee Your next cup will be perfect chapter 10a explains the use of the sensor touch symbols Please note If coffee only comes out of one spout move the spout up and down a few times to clear the internal flow You are now ready to make coffee 12 7 ADDING COFFEE BEANS e Open the bean container lid Fig 1 9 fill with beans Fig 6 The container holds approx 220 grams 8 oz Close the lid Frozen Beans Let them thaw for 3 to 4 hours before adding into the bean container This will prevent moisture from seeping into the grinder Sugar Coated Beans DO NOT fill sugar coated beans into the grinding chamber The sugars will stick to the burrs and clog the flow of ground coffee Have your local coffee emporium grind the sugar coated beans for you and use as described in chapter 11 Using Oily Beans Beans with an oily surface tend to stick together This may prevent a continuous flow of beans from the bean container into the burrs As a result the grinder does not grind enough coffee and you might get weak or no coffee at all Stir the beans in the bean container just before grinding Alternatively you can also
14. T to confirm e Press the P Button to return to SELECT PRODUCT 18e PROGRAMMING STEAM PORTION The steam portion can be programmed between 3 and 60 sec onds The factory setting is STEAM 60 SEC e Press the P Button e Touch the arrow until the display shows STEAM 60 SEC e Touch ST RT The number 60 starts blinking e Touch either arrow repeatedly until the desired duration is shown e Touch ST RT to confirm e Press P button to return to SELECT PRODUCT Please note During steaming you can always stop the flow of steam by simply pushing the Steam Button This will not change the setting When the steam output stops you can immediately resume steaming by pressing the steam button again 18f PROGRAMMING WATER PORTION The Hot Water Button can be programmed to dispense any amount up to approx 16 oz 480 ML The factory setting is 5 oz 150 ML 19 Press the P Button Touch the right arrow until the display shows WATER PORTION Place a cup or container underneath the frother Fig 15 Touch ST RT The display shows PRESS KEY and the red light in the Hot Water Button illuminates e Push the Hot Water Button Hot water will be pumped through the frother into the cup The display reads ENOUGH WATER PRESS KEY e When the desired amount of hot water is dispensed push the Hot Water Button to stop the flow The amount of hot water in your cup is now programmed The display shows WATER PORTION e Press the P button
15. Your Jura Capresso automatic coffee center will always produce espresso and coffee with a thick foamy layer called crema The crema traps the fine aro matics and the light gaseous flavors that register on the palate The high pressure and the short brewing time prevent the extraction of bitter oils and release less caffeine than any other brewing methods You will always make the absolute freshest and most aromatic cup of coffee This is the reason why many European restaurants and hotels serve fresh pressured brewed coffee only Experiment with your new machine and prepare yourself the best and most enjoyable cup of coffee 3b PRESSURE BREWING You can make any quantity of coffee from 1 to 16 oz Please note in order to create the crema on top of your coffee the machine brews coffee at slightly lower temperatures than a drip coffee maker Since your coffee is delivered directly into your cup we recommend to enjoy it immediately see chapter 21 3c DIFFERENT COFFEE DRINKS Here are some guidelines for the most popular coffee drinks e Ristretto to 1 oz of coffee e Espresso 1 to 2 oz coffee e Double Shot 3 to 4 oz of coffee Sweeten to taste for the above drinks e Crema Coffee 5 to 7 oz of coffee e Cappuccino Espresso plus 3 to 4 oz of hot frothed milk 10 e Latte Espresso plus 3 to 5 oz of steamed milk with little or no froth e Caf Mocha Make Espresso then add chocolate syrup to the milk before froth
16. ack to your regular coffee Push the Rinse Button Fig 3b once or twice to process some water through the coffee spouts 12 USING HOT WATER With the Hot Water Button Fig 4a you can make a cup of tea a quick soup or add hot water to your coffee making it less strong Caution Always make sure that you have a container under neath the frother Fig 15 when using the hot water function otherwise hot water might splatter causing severe injuries e Push the Hot Water Button WATER PORTION Hot water will flow immediately out of the frother e To stop the water flow push the Hot Water Button again Please note The hot water portion is set to approx 5 oz It can be programmed from 1 to 16 oz chapter 18f 13 FROTHING STEAMING AND HEATING The steam function can be used to heat up any liquid and to steam and froth milk 14 Steaming Position The metal cylinder is in the UP position Fig 18 In the steaming position hot steam is injected into the milk or any other liquid without creating a frothy layer on top Frothing Position The metal cylinder is in the DOWN position Fig 18 In the froth ing position hot steam and air is injected into the milk creating warm milk and a firm layer of tiny froth bubbles 14 HEATING AND FROTHING MILK e Fill a pitcher 10 to 12 oz capacity or a large cup with at least 4 to 5 oz of cold milk e Push the Steam Button Fig 4b The Steam Button s red light will start blin
17. ainer Touch screen control display See Fig 5 Steam Hot Water Buttons See Fig 4 Dual Frother Plus Stainless Steel Removable Grid Removable Drawer Measuring Scoop Two Cleaning Tablets white Water Hardness Indicator Strip Claris Water Cartridge unpacked Fig 2 19 Used Coffee Container 20 Tray 13 Grid 14 Drawer Operating Buttons a On Off b Rinse PRESS MAINT c 1 Cup d 2 Cup e Programming f Pre Ground Coffee a Hot Water b Steam a BIG CUP e MILD b COFFEE f NORMAL c ESPRESSO g STRONG d ST RT Dual Frother Plus Page Important Safeguards Jura Capresso 2 Ilustr tions toria einen 4 7 1 Product Registration ii 9 2 Customer Serice unssseennennnennsnnennnnnnnnnnannnnnnennnnannnnn 9 3 WELCOME TO THE IMPRESSA P9 9 a A Word about Crema Coffee 10 b Pressure Brewing 10 c Different Coffee Drinks 10 d Goffee Facts 10 4 Please Don t Please DO 10 5 Factory Settings i 11 6 PREPARING MACHINE FOR THE FIRST
18. am milk for delicious cappuccinos and lattes The frother can be programmed to produce steam up to 60 seconds Need more steam Just push the steam button again for another 60 seconds of steam The stainless steel lined ThermoBlock prevents water from coming in contact with alu minum and allows you to brew coffee immediately after frothing no purging The hot water function lets you prepare tea and other beverages in seconds All important functions such as water level bean container used coffee container and water filter are monitored automatically You can even program the machine to turn itself on and off You can change the language and can check how many cups of coffee you made Please watch the enclosed video and study this instruction manual before you use the machine on a daily basis You will get so much more out of your IMPRESSA F9 Enjoy If you prepare many cappuccinos or lattes at a time we recommend the fast and precise frothXpress PLUS system separately available This system replaces the Dual Frother Plus and lets you fill cup after cup with the desired amount of hot milk and milk froth automatically For details visit our website www capresso com and watch the videos about the frothXpress Plus system Super Automatics Impressa S9 9 3a AWORD ABOUT CREMA COFFEE According to the majority of coffee experts grinding tamping and brewing under high pressure is the ideal extracting process for maximum flavor and aroma
19. are removed from the machine and the water tank e Make sure the machine sits on an even flat surface and the drawer tray and used coffee container are inserted e Plug in machine e Do NOT fill water tank now Important Do not install the Claris Filter cartridge now It can block the machine e Turn the machine on by pressing the ON OFF button Fig 3a The display shows WWW IMPRESSA F LINE COM then FILL WATER e Remove water tank fill with fresh cold water and replace The following procedure is only necessary when setting up the machine for the first time and after the procedure Emptying System Before Transport chapter 19f FILL SYSTEM WATER PORTION The red light in the Hot Water Button Fig 4a illuminates Ads e Place a cup underneath the frother Fig 15 and push the Hot Water Button SYSTEM FILLING The machine will pump some water through the frother and stop automatically YOUR MACHINE IS HEATING PRESS MAINT e Move the cup underneath the coffee spout Fig 14 and press the Rinse Button Fig 3b MACHINE RINSING The machine will pump hot water through the coffee spout and stop auto matically SELECT PRODUCT The display will illuminate the cup and strength selection as shown below In this setting the machine is ready to brew coffee e Open the bean container lid and fill with some beans Fig 6 e Place an empty cup at least 8 oz under the coffee spouts e Touch and hold your finger on the S
20. cles will make it impossible to create milk froth Fast cleaning e Immediately after finishing frothing place a cup underneath the frother Fig 15 and push the Hot Water Button Fig 4a Let hot water run through the frother for about 3 seconds This will flush out any small milk droplets e Push the Hot Water Button again to stop Thorough cleaning of the Dual Frother parts e Remove the Dual Frother Fig 16 from the Steam Nozzle Fig 17c by pulling down the soft collar of the clip on connector e Unscrew the black tip Fig 16a from the Clip On Connector Fig 16c You can use a coin to loosen the black tip e Soak all three parts in hot soapy water Make sure that the two side holes and the channel of the black tip Fig 16a are free of any milk deposits Cleaning the steam nozzle Fig 17 e Place a cup underneath the Steam Nozzle the Dual Frother is off and press the Hot Water Button Let hot water run for a few seconds through the Steam Nozzle e Push the Hot Water Button again to stop Tip If the steam nozzle is blocked by hardened milk use a needle and loosen up the milk deposit Then let some hot water pass through the Steam Nozzle Assembly of Frother Parts e Make sure the Steam Nozzle Fig 17c is screwed onto the Metal Tube Fig 17a finger tight e Assemble the Dual Frother and make sure that the tip is screwed onto the Connector Fig 16a c finger tight e Push the black Clip on Connector Fig 1
21. er are not assembled properly or the components are clogged with hardened milk or one or more of the components is missing or the steam nozzle is clogged Solution a Remove frother Check that steam comes out of the steam nozzle If not use a needle and clear blockage from inside steam nozzle b Clean all other frother parts and assemble properly See chapter 15 c If any parts are missing call Customer Service 1 800 220 5701 or use the enclosed mail order form to order the missing part 26 D GRINDER MAKES AN EXTREMELY LOUD NOISE NO BEANS ARE GROUND Reason A stone is blocking the burr grinder Solution Call customer service 1 800 220 5701 E THE DRAWER Fig 21 DOESN T PULL OUT Solution Turn off the machine Wait a minute Turn machine on and wait until it stops making any noise Now try to pull out the drawer If this does not work try the above procedure again If you are still unable to remove the drawer call customer service 1 800 220 5701 Jura Capresso LLC 81 Ruckman Road Closter NJ 07624 1 800 220 5701 e 201 767 3999 Fax 201 767 9684 email contact capresso com Website www capresso com 27
22. he P Button e Touch the right arrow until the display shows UNIT ON Touch ST RT The hour segment starts blinking Touch either arrow repeatedly to set the hours Touch ST RT to confirm The minute segment starts blinking Touch either arrow repeatedly to set the minutes Touch ST RT to confirm Now the Auto Turn On time is set Press the P button to return to SELECT PRODUCT 18i SETTING THE AUTO SHUT OFF Your F9 is programmed to turn off 2 hours after last use Select from hour to 9 hour shut off or no automatic shut off e Press the P Button e Touch the right arrow the display shows OFF AFT 2 0 HRS Touch ST RT Touch either arrow repeatedly until desired setting is displayed Touch ST RT to confirm e Press the P button to return to SELECT PRODUCT Please note In order for the machine to turn off automatically it must be in the SELECT PRODUCT mode If you leave the machine in programming mode red arrows showing or in any other mode the machine will not turn off automatically 18j SETTING LANGUAGE The F9 is set to ENGLISH You can change the display to German French Italian Spanish Portuguese or Dutch e Press the P Button e Touch the right arrow until the display shows LANGUAGE ENGLISH Touch ST RT Touch either arrow repeatedly to select the desired language Touch ST RT to confirm e Press the P button to return to SELECT PRODUCT 18k CUP COUNTER The cup counter shows the total number of
23. holder for the cartridge so that it engages in the water tank Fig 12 e Fill the water tank with fresh cold water and replace You must activate the cartridge as follows e Push and hold the P button The display shows lt FILTER NO gt e Touch the ST RT the word NO starts blinking e Touch either arrow display shows FILTER YES e Touch the ST RT to confirm The display shows INSERT FILTER WATER PORTION e Place a large container underneath the frother at least 30 oz capacity e Push the Hot Water Button The machine pumps water through the frother activating the filter This will take about 90 seconds During this time the display reads FILTER RINSING When the water flow stops the displays reads YOUR MACHINE IS HEATING The machine automatically returns to its coffee brewing setting SELECT PRODUCT 16 Please note As long as the filter is activated the water hardness setting is automatically turned off 16b REPLACING THE CLARIS CARTRIDGE The filter is monitored automatically After approx 50 liters of water 55 quarts the filter loses its effect The display will show REPLACE FILTER SELECT PRODUCT You can still make coffee but we recommend replacing the filter within one week Attention The filter should be changed every 2 months if you use less than 50 liters of water In this case no message will appear in the display Important Once the filter has lost its calcium suppressing abili ties calcium wi
24. ing steaming Experiment with the size of your milk based drinks For stronger coffee taste add more coffee for more milk taste use more frothed milk 3d COFFEE FACTS e Caffeine is tasteless A strong coffee or espresso is mostly the result of the amount of coffee in relation to the amount of water The longer a bean is roasted the less caffeine it has e Arabica and Robusta are two genetically different kinds of beans Arabica beans have more flavor and a little less caffeine than Robusta beans which are mostly used in lower priced coffees and instant coffees e Espresso is not a bean it s the way the coffee is roasted and prepared Typical US espresso roasts result in darker beans with an oily outside European espresso roasts are medium brown with no or very little oils showing on the outside Please note If you use dark oily beans see chapters 7 amp 8 for special handling A PLEASE DON T or you void your warranty protection Never fill instant coffee into the grinder or ground coffee funnel it can damage the functioning of the brewing chamber Never fill sugar coated coffee beans into the bean container Never fill frozen beans into the bean container If you store beans in the freezer let them thaw for 3 to 4 hours before filling them into the bean container e Never fill anything other than coffee beans into the bean con tainer no chocolate rice nuts spices etc e Never fill anything but f
25. king and the display reads YOUR MACHINE IS HEATING After a few seconds the red light stays illuminated and the display reads SELECT PRODUCT e Immerse the tip of the frother into the milk and push the Steam Button again Fig 4b Hot steam will be injected into the milk During this time the display shows STEAM PORTION e To stop the steam function push the Steam Button again Please note Steam output will automatically stop after 60 sec onds If you need more steam just push the Steam Button again and you will have another 60 seconds of steam You can also change the steam output to a shorter interval chapter 18e Tips for frothing Cappuccino Start in the steaming position cylinder up for 10 to 20 sec onds This way your milk will be warmed up first Then push the cylinder down Milk froth will build up This way the froth on top of your milk is also warm If the frothed milk is not warm enough continue in the steaming position Steaming and frothing directly in your cappuccino cup With practice you can steam and froth directly in your cappuccino cup First steam and froth the milk then add your espresso shot Skim milk will produce the most froth and will let you taste more of the coffee 1 and 2 milk will give you less froth Regular whole milk 3 fat will produce the least amount of froth 15 CLEANING THE DUAL FROTHER PLUS Always keep the Dual Frother Plus clean and free of milk deposits Hardened milk parti
26. l Option Two 1 Cup and 2 Cup Buttons In addition to the nine selections on the touch screen you can also use the 1 Cup and 2 Cup button Fig 3c 3d to grind and brew coffee Please see chapter 5 for the amount of coffee brewed for these buttons To change these cup sizes see chapter 18d Please note The 2 Cup button will automatically brew twice as much coffee max 160z as the 1 Cup button 11 USING PRE GROUND COFFEE You can also use pre ground coffee bypassing the grinder This comes in handy if someone requests decaf sugar coated or flavored coffee e Push the Pre Ground Coffee Button Fig 3f The display shows FILL POWDER SELECT PRODUCT e Open the lid for the ground coffee funnel Fig 1 8 and fill the funnel with one or two scoops of ground coffee 13 Important Do NOT fill this funnel with instant coffee and do not use more than two level scoops of coffee e Touch one of the three cup symbols to select cup size and then touch ST RT While brewing the display shows for example BIG CUP POWDER Please note When using pre ground coffee you cannot use the 1 Cup or 2 Cup button Please note If you push the scoop button accidentally touch ST RT to clear The F9 starts the brewing process and stops after a few seconds The display will return to SELECT PRODUCT Please note After use of sugar coated or flavored coffee through the pre ground coffee funnel you may experience some flavor transfer when going b
27. ll build up inside the machine Since the Water Hardness Selector is off the machine will not remind you when to decalcify This could clog and ruin your machine e Remove the old filter The cartridge is environmentally friendly Dispose it with your regular household trash e Make sure the water tank is empty e Remove cartridge from its bag e Open water container lid and pull up the holder for the Claris cartridge Fig 10 e Insert the cartridge with its tapered end down Make sure it fits snugly over the white mesh piece inside the water container Push down gently Fig 11 e Close the holder for the cartridge so that it engages in the water tank Fig 12 e Fill the water tank with fresh cold water and replace e Turn the machine off e Push and hold the Rinse Button The machine beeps and the display shows WATER PORTION INSERT FILTER e Place a large container underneath the frother at least 30 oz e Push the Hot Water Button The machine pumps water through the frother activating the new filter This will take about 90 seconds During this time the display shows FILTER RINSING When the water flow stops the displays shows YOUR MACHINE IS HEATING The machine automatically returns to the coffee brewing mode SELECT PRODUCT 17 ADJUSTING THE WATER HARDNESS Important If the Claris Cartridge is activated see chapter 16a this chapter does not apply The water is heated inside the machine With use this leads t
28. lug from wall outlet 12 Do not use appliance for other than intended use 13 Use extreme caution when disposing hot steam 14 For household use only SAVE THESE INSTRUCTIONS SPECIAL CORD SET INSTRUCTIONS Regarding your cord set A A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord B Longer detachable power supply or extension cords are available and may be used if care is exercised in their use C If a long detachable power supply cord or extension cord is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the exten sion cord should be a rounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over NOTICE Your Impressa F9 has a 3 prong grounded plug To reduce the risk of electrical shock this plug will fit in an outlet only one way If the plug does not fit in the outlet contact a qualified electrician DO NOT modify the plug in any way CAUTION This appliance is for household use Any servicing other than cleaning and user maintenance should be performed by an authorized service representative e Do not immerse base in water or tr
29. new IMPRESSA F9 for house hold use only commercial use voids warranty One Year or 4 000 coffee brewings whichever comes first This warranty is in effect for the period and usage described above from the date of the first purchase and is limited to the United States of America This warranty covers all defects in materials or workmanship parts and labor including free UPS ground transportation for both ways within the continental United States For Hawaii and Alaska freight is not covered by this warranty TRANSPORT When sending the machine use the original pack ing materials the inner and outer cartons or use approximately 2 of bubblewrap and insert machine in a carton which will hold 40lbs Any damage in transit is NOT covered by this warranty This warranty does not cover e Any machine NOT distributed by JURA CAPRESSO within the United States e Any machine not purchased from an Authorized Dealer e Damage caused by accident abuse negligence misuse improper operation or failure to follow instructions contained in this manual e Any service or alteration performed by an unauthorized person company or association e Damage caused by neglecting and omitting maintenance cleaning and decalcifying cycles e Damage caused by use of instant coffee or any other ingredients not allowed in this product Other limitations and exclusions Any implied warranties including fitness for use and mechantability are limited
30. not inter rupt the procedure e Make sure the machine is on and the water tank is full e Push and hold the Rinse button until the display shows EMPTY TRAY e Remove and empty the drawer and replace complete assembly Fig 23 Important Even if the drawer is empty you still need to remove it for approx 20 seconds and then replace it The display shows PRESS MAINT e Push the Rinse Button Fig 3b The display shows MACHINE CLEANING After a moment the machine beeps and the display shows TABLET PRESS MAINT e Open the ground coffee lid and drop in one white cleaning tablet Fig 24 e Push the Rinse button The display shows MACHINE CLEANING The cleaning program will dispense hot water in intervals through the coffee spout into the drawer e When finished the display shows EMPTY TRAY and the machine beeps e Lift and remove the drawer Empty the used coffee container and drawer and replace The display shows SELECT PRODUCT indicating the machine is now ready to brew coffee again 20b DECALCIFYING PROCEDURE The machine has an integrated decalcifying program When the display shows MACHINE SCALED SELECT PRODUCT it is time to decalcify the machine You can still make coffee howev er it is highly recommended that you decalcify the machine within the next 3 to 4 days Please note If you use the Claris water cartridge and the dis play shows MACHINE SCALED SELECT PRODUCT then your cartridge function is not activated
31. o calcium deposits forming inside the machine The display will remind you when it is time to perform a decalcifying cycle The machine is set to level 2 medium hard water If you have hard er water you need to set it to a higher level If you have softer water you can set it to level 1 If you are not sure about the hardness of your water ask your local water company for the Water Hardness in Grains HARDNESS LEVEL 1 grains 2 9 HARDNESS LEVEL 2 grains 10 19 HARDNESS LEVEL 3 grains 20 29 HARDNESS LEVEL 4 grains 30 You can also use the enclosed water hardness indicator strip to determine the water hardness e Insert the stick for one second into the water you want to use Shake off any access water and wait for one minute e If all five fields of the test stick turn reddish set the hardness level to 4 If four fields turn reddish set the hardness level to 3 If three or less fields turn reddish leave the level in position 2 You can change the hardness settings as follows SELECT PRODUCT e Push and hold the P button Fig 3e until you hear a beep The display will show two red arrows and FILTER NO e Touch the right hand arrow once and the display shows HARDNESS LEVEL 2 e Touch ST RT until you hear a beep The 2 starts blinking e Touch the left or right arrow until the desired number appears 1 2 3 4or e Touch ST RT to confirm The number stops blinking e Push the P button to return to SELECT PRODUCT Imp
32. ortant If you choose the selection the water hardness monitor is turned off In this case the machine will NOT remind you when it is time to decalcify Turning off the monitor requires you to use distilled water only or the Claris Filter chapter 16a If you use regular or bottled water the machine will build up cal cium If calcium build up inside the machine is not removed it can lead to a complete machine break down 18 PROGRAMMING Please note As long as you are in programming mode you cannot brew coffee You can change a variety of functions To get into programming mode press and hold the P button Fig 3e You will hear a beep 17 and two red arrows will appear in the touch screen display panel indicating that you are in programming mode The first screen will show lt FILTERNO gt By repeatedly pushing the right arrow gt the display shows all the functions you can change or check WATER HARDNESS LEVEL 2 AROMA STRONG TEMP HIGH WATER QUANTITY 1 CUP 150 ML STEAM 60 SEC WATER PORTION TIME UNIT ON OFF AFT 2 HRS SUPPLIED LANGUAGE ENGLISH Changing the different functions works in the following pattern e Push and hold the P button until the two red arrows show in the display e Go to the function you want to program by repeatedly pushing the left of right arrows Touch ST RT Change the function to the desired setting using either arrow Confirm the new setting by to
33. ouch the right arrow until the display shows WATER QUANTITY e Touch ST RT The display shows SELECT PRODUCT and illuminates the three cup symbols Please note touch all three cup symbols and the display will show you the actual cup size e g BIG CUP 240 ML or ESPRES SO 60 ML a Touch the cup symbol for which you want to change the size e g ESPRESSO 60 ML b Touch ST RT The number 60 starts blinking c Use the right arrow to increase the left arrow to decrease the size Push the arrow repeatedly until the desired cup size is displayed e g ESPRESSO 45 ML 1 oz d Touch ST RT to confirm The display shows WATER QUANTITY You can touch another cup symbol to change that size repeat steps a through d or press the P Button to return to SELECT PRODUCT 18d PROGRAMMING THE 1 CUP BUTTON You can change the cup size for the 1 Cup Button Fig 3c Choose from 30 to 240 ML 1 to 8 oz Please note The 2 Cup Button automatically delivers twice as much coffee The factory setting for the 1 Cup Button is 120 ML 4 oz for the 2 Cup Button 240 ML 8 oz Press the P Button Touch the arrow until the display shows 1 CUP 120 ML Touch ST RT The number 120 starts blinking Touch the right or left arrow repeatedly until the desired size is displayed e Touch ST RT to confirm The display lets you now select the strength for the 1 CUP button e Touch the bean symbols to choose MILD NORMAL or STRONG e Touch ST R
34. r and when we can call you back You can also send us a FAX at 201 767 9684 or EMAIL us at contact capresso com 3 WELCOME TO THE IMPRESSA F9 This fully automatic coffee center is completely programmable and extremely user friendly The Impressa F9 is made of the finest materials and features a unique sensor touch panel The chrome plated metal front with its heavy duty die cast coffee spout the stainless steel grid and the elegant cup illumination make it the center piece of any contemporary kitchen The Impressa F9 can prepare one or two cups of crema coffee at a time The two step pressure brewing system well known in commercial applications was adapted and refined by Jura coffee specialists and is the trademark of each Jura Capresso coffee center This Pre Brew Aroma System chapter 10 ensures optimal coffee extraction and will finish every cup with a rich layer of crema proof for perfectly pressure brewed coffee By touching one of three cup symbols and one of three bean sym bols you choose the cup size and the coffee strength you want Touch the ST RT button and the F9 will grind and brew your personal cup of coffee The integrated solid steel conical burr grinder grinds beans to the preferred fineness A separate funnel lets you use pre ground coffee All coffee water and steam functions are programmable to your own personal taste Make any size cup of coffee between 1 and 16 oz The Dual Frother Plus lets you froth and ste
35. resh cold clean water into the water container except when decalcifying chapter 20b e Never use mineral or carbonated water You can use tap water spring water distilled water and reverse osmosis water e Never repair or open the machine yourself All repairs should be performed only by an authorized service center PLEASE DO e Fill water tank with fresh cold water only e Remove any foreign particles small stones from coffee beans e Let frozen beans thaw for 3 to 4 hours before pouring them into the bean container All Display Messages Are Shown in GREEN 5 FACTORY SETTINGS Each machine leaves the factory with the following settings Filter 22 NO Hardness Level 2 Aroma Strong Temperature High Big Cup 240 ml 8 oz Coffee Cup 150 ml 5 oz Espresso Cup 60 ml 2 oz 1GUPi lan 120 ml 4 oz 2 CUP 240 ml 8 oz Water Portion 150 ml 5 oz Steam 60 seconds Time sran not set Unit On not set Auto Off 2 hours after last use Language English CUP ILLUMINATION Fig 13 The cup illumination adds a dramatic touch to brewing coffee Providing the machine is plugged in you can activate the cup illumination for 1 minute by pressing any button 6 PREPARING THE MACHINE FOR THE FIRST TIME e Make sure all accessories literature and any other items
36. splay reads SELECT PRODUCT The cup and bean symbols illuminate You are now ready to make coffee 10 GRINDING AND BREWING The F9 uses a 2 step brewing process Pre Brew Aroma System This process first moistens the ground coffee pre brew phase stops for a few seconds and then starts the brewing process Please note After the pre brew phase you can stop the brewing process at any time by simply pushing the 1 Cup button This will not affect your cup settings 10a SELECTING CUP SIZE AND STRENGTH With the machine in the SELECT PRODUCT mode you can choose five cup settings and three different strength settings e Adjust the height of the coffee spout to your cup size Fig 14 and place one or two cups underneath the coffee spouts Option One Touch Screen Controls Fig 5 On the touch screen display you can choose from three cup sizes and three strength settings for total of 9 settings BIG CUP COFFEE ESPRESSO each in MILD NORMAL or STRONG e Touch the symbols and watch how the display changes e Once you have selected your preferred combination just touch and hold ST RT until grinding begins Please see chapter 5 for the amount of coffee brewed for each of the symbols To change these cup sizes see chapter 18c Please note You need to touch ST RT for one second to activate the grinding brewing process This delayed action prevents the machine from making coffee if somebody accidentally touches the ST RT symbo
37. to return to SELECT PRODUCT Please note When pumping hot water through the steam noz zle you can always stop the flow of hot water by simply pushing the Hot Water Button This will not change the programmed set ting When the hot water output stops you can dispense more by pressing the Hot Water button again 18g SETTING THE TIME You can enter the actual time into the machine Once the time is set you can then program the machine to turn on at a specific time next chapter Please note The time is displayed in the 24 hr mode not AM PM If the actual time is 3 45 pm you must set the time to 15 45 e Press the P Button Touch the right arrow until the display shows TIME Touch ST RT The hour segment starts blinking Touch either arrow repeatedly to set the hours Touch ST RT to confirm The minute segment starts blinking 20 e Touch either arrow repeatedly to set the minutes e Touch ST RT to confirm Now the actual time is set e Press the P button to return to SELECT PRODUCT Please note The Impressa F9 will keep the time as long as the machine is plugged in If you unplug the machine or if you have power interruption the time will be lost 18h SETTING THE AUTO ON TIME You must first set the time chapter above You can set the machine to turn on at a specific time It will turn on at that time warm up and the display shows PRESS MAINT Press the Rinse Button and you are ready to brew coffee e Press t
38. uching ST RT Push the P button to leave programming mode PROGRAMMING ACTIVATING CLARIS FILTER Activating the Claris Cartridge is explained in chapter 16a 18 PROGRAMMING WATER HARDNESS Changing the water hardness level is explained in chapter 17 18a PROGRAMMING AROMA The factory setting is STRONG You can change to NORMAL In NORMAL the Impressa F9 will grind a little less coffee in each of the three strength selections coffee bean symbols e Press the P Button e Touch the right arrow symbol repeatedly until the display shows AROMA STRONG e Touch ST RT e Touch the right arrow once AROMA NORMAL e Touch ST RT to confirm e Press P button to return to SELECT PRODUCT 18b PROGRAMMING TEMPERATURE The factory setting is HIGH You can change to NORMAL In NORMAL the temperature is approx 7 F lower than in high e Press the P Button e Touch the right arrow until the display shows TEMP HIGH Touch ST RT Touch the right arrow once TEMP NORMAL Touch ST RT to confirm e Press P button to return to SELECT PRODUCT 18c PROGRAMMING WATER QUANTITY cup sizes Each of the three cup symbols Fig 5 in the touch screen dis play can be set to any size from 30 and 240 ML milliliters respectively 1 to 8 oz 30 ML 1 oz The factory settings for the three cup symbols are BIG CUP ann 240 ML 8 oz COFFEE cup 150 ML 5 oz ESPRESSO cup 60 ML 2 oz e Press the P Button e T
39. ugh the system Solution Remove water container and make sure that the con necting valve is free of any particles like a coffee bean etc Reason The ground coffee funnel is clogged the internal brew ing chamber is clogged Solution Place a large cup underneath the coffee spout Push the rinse button Fig 3b a few times until the blocked coffee is removed Never fill more than 2 scoops of coffee in the ground coffee funnel the funnel is not a storage area for ground coffee Also use a ground coffee which is ground somewhat coarser 25 B THE DISPLAY READS FILL WATER BUT THERE IS ENOUGH WATER IN THE WATER TANK Reason The low water floatation device Fig 8 4 is missing Solution Within the water tank is a small compartment like a mouse trap Inside is a small black floatation device On top is a small clear see through plastic cover This small plastic cover is missing and the floatation device is outside of the small com partment Check if you can locate both pieces and put it back together If you cannot find them call 1 800 220 5701 We will send the pieces to you FREE OF CHARGE C INSUFFICIENT FROTHED MILK PRODUCTION Reason Milk is initially not cold enough or your milk is not suited for thick frothing Solution Make sure milk is cold Use a different type of milk Skim milk will produce the thickest and longest lasting froth Full fat milk will produce less thick froth Reason The components of the froth
40. y to disassemble e To reduce the risk of fire or electric shock do not remove the base No user serviceable parts inside Repair should be done by authorized service personnel only e Check voltage to be sure that the voltage indicated on the name plate agrees with your voltage e Never use warm or hot water to fill the water container Use cold water only e Keep your hands and the cord away from hot parts of the appliance during operation e Never clean with scouring powders or hard implements JURA CAPRESSO Jura was founded in 1931 in Switzerland Capresso was founded in 1994 in the USA Both companies have joined forces in the US to bring you the best Fully Automatic Coffee Centers available anywhere With innovative and user friendly features high quality materials clear instructions and superb customer service we are sure you will experience the best coffee espresso Cappuccino or latte you have ever had We hope you will enjoy your new Fully Automatic Coffee Center and will recommend it to your friends For more information about our products visit our website www capresso com Michael Kramm President SEND NWUIPOAD Height Adjustable Coffee Spout Operating Buttons See Fig 3 Removable Water Tank Low Water Flotation Device See Fig 8 4 Claris Water Care Cartridge Not Installed Service Plug Lid for Water Tank Ground Coffee Funnel Lid for Ground Coffee Funnel Lid for Bean Cont
Download Pdf Manuals
Related Search