Hunter Fan 41923 Fan User Manual
Contents
1. gt Hanger Bracket gt Canopy Trim J Ring Should you need to remove the canopy trim ring follow these steps 1 Locate the tab indicators small bumps on top of tabs 2 Press firmly on opposite sides of the ring towards the canopy The tabs will flex out releasing the trim ring from the canopy Step 5 3 Steps 5 4 5 5 42013 01 02 02 05 Hunter Fan Company 6 Assembling the Blades Step 6 1 Detail Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Remove the blade mounting screws and rubber shipping bumpers from the motor 6 4 For each blade insert one blade mounting screw through the Blade Assembly blade iron and attach lightly to the fan Insert the second blade PEN mounting screw then securely tighten both mounting screws Steps 6 1 6 2 3T i 10 Use without grommet Blade Mounting Screw Hunter Fan Company 42013 01 02 02 05 A WARNING Use only the light fixture supplied with this fan model 7 1 7 7 3 7 4 7 5 7 6 To attach the upper switch housing partially install2. Housing Plug Steps 7 5 7 6 Connector Plug Lower Switch sul eer Housing oral Housing Assembly Screw Hunter Fan Company 7 Installing the Light Kit Continued 7 7 To install the glass shades Place the silencer band around the neck of each glass shade Insert each glass shade in a shade cup 7 8 Install and tighten the three thumb screws Do not overtighten 7 9 Install medium base incandescent light bulbs maximum 60 Watt 12 Step 7 7 7 8 Thumb Screw Hunter Fan Company 42013 01 02 02 05 8 1 8 2 8 5 8 6 8 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector The light pull chain controls power to the light The pull chain has two settings On and Off Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causin
3. Installation and Operation manual for Hunter Ceiling Fans 42013 01 02 02 05 Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan For Your Records and Warranty Assistance Model Name We are proud of our work We appreciate the opportunity to supply Catalog Model No _ _ __ you with the best ceiling fan available anywhere in the world Serial No Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Date Purchased Where Purchased i Cautions and Warnings For reference also attach your receipt or a e Read this entire manual carefully before beginning installation Save copy of your receipt to the manual theseihetrucion e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the 2 Installing the Hanger Bracket outlet box and associated wall switch location If you cannot lock the circuit breakers in the off p
4. if the blade is cracked If so replace all the blades 3 Be sure that the glass is secure 4 Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our WEB site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 42013 01 02 02 05
5. two 6 32 x 3 8 housing assembly screws into the switch housing mounting plate Feed the upper plug connector through the center opening of the housing Align the keyhole slots in the housing with the housing assembly screws Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Install the remaining 6 32 x 3 8 screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing and light fixture falling To attach the lower switch housing connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three 6 32 x 3 8 housing assembly screws 42013 01 02 02 05 Steps 7 1 7 3 7 Installing the Light Kit Housing j E Assembly Upper Screw Switch ll
6. blades was damaged in shipment return all the blades for replacement Installing Multiple Fans If you are installing more than one fan keep the fan blades in sets as they were shipped If any parts are missing or damaged contact your Hunter dealer or call Hunter Parts Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings Hunter Fan Company 42013 01 02 02 05 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Note Your fan comes with four pre installed neoprene noise isolators 2 2 Thread the lead wires from the outlet box down through the hole in the middle of the hanger bracket 2 3 Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other If you are installing the fan on an angled ceiling be sure to orient the hanger bracket with the large opening towards the ceiling peak Note The isolators should be flush against the ceiling 2 4 Place a flat washer on each of the two 3 screws and pass the screws through the slot
7. coating prevents the downrod from unscrewing Once assembled do not remove the downrod lt Downrod A WARNING Do not carry or lift fan by canopy 3 5 Raise the fan and place the ball into the hanger bracket lt Canopy 3 6 Align the notch on the ball with the indent in the hanger bracket with Washer Rotate the fan until you hear the notch pop into place Go to 4 e Wiring the Fan Canopy Trim Ring A WARNING Fan may fall if not assembled as directed in these mr lt K Set Screw installation instructions 7s a n oe m Steps 3 5 3 6 Hunter Fan Company 42013 01 02 02 05 3 e Assembling and Hanging the Fan Low Profile Only You can assemble your fan for standard or angle mounting as shown Steps 3 8 3 10 in steps 3 1 3 6 on the previous page For low profile mounting ceilings less than 8 feet high see steps 3 7 3 11 on this page Low Profile Washer 3 7 Locate the washer that comes preassembled in the canopy Remove the label and discard the washer and label Locate the set screw preassembled in the adapter Remove and discard the set screw Refer to images on previous page 3 8 Place the low profile washer from the parts sack into the canopy 3 9 Place the canopy trim ring and canopy with washer on top of the fan assembly 3 10 Align the screw holes in the washer with the holes in the adapter Assemble securely wi
8. g a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan Reversing Switch 42013 01 02 02 05 In warm weather use downward air flow pattern In cold weather use upward air flow pattern Hunter Fan Company 13 9 Troubleshooting 14 Hunter Fan Company Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly up or down to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Check to see
9. ire from the fan e The black wire from the ceiling to the black wire from the fan e The black white wire from the fan to the wire for the wall switch Alternatively you can control both fan and light with one switch To do so connect the wires as follows e The bare or green ground wire from the ceiling to the green ground wire from the hanger bracket and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black and the black white wire from the fan To connect the wires hold the bare metal leads together and place a wire nut over them then twist clockwise until tight A CAUTION Be sure no bare wire or wire strands are visible after making connections Push all wires and wire nuts back into the hanger bracket 42013 01 02 02 05 5 1 5 5 Raise the canopy over the hanger bracket For low profile Twist canopy clockwise to secure 5 4 5 Installing the Canopy and Canopy Trim Ring Partially install two canopy screws about 2 full turns in the Steps 5 1 5 2 hanger bracket installations you will need to remove the canopy from the hook first Align partially installed screws with key slots in canopy Install third canopy screw in round hole on canopy Securely tighten all three screws Using both hands push the canopy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place
10. ng a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls 10 Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high Angle Mounting recommended for a vaulted or angled ceiling 42013 01 02 02 05 Standard Mounting hangs from the ceiling by a downrod included recommended for ceilings 8 feet or higher For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Hunter Fan Company l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver e Phillips head screwdriver e Wrench or pliers Check Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Check for any shipping damage to the motor or fan blades If one of the fan
11. osition securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical 5 Installing the Canopy and codes and ANSI NFPA 70 If you are unfamiliar with wiring use a Canopy Trim Ring qualified electrician To reduce the risk of personal injury do not bend the blade Table of Contents 1 e Getting Ready 3 Assembling and Hanging the Fan 4 Wiring the Fan 6 Assembling the Blades 7 Installing the Light Kit attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed 9 e Troubleshooting controls 8 Operating and Cleaning Your Ceiling Fan 2004 Hunter Fan Company Hunter Fan Company 42013 01 02 02 05 Installer s Choice and Optional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angle mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories includi
12. ted holes in the hanger bracket into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Screw eerie FP EU UNUUETEDEVU NUE be 42013 01 02 02 05 2 Installing the Hanger Bracket Isolator gt Hanger Bracket Cl Steps 2 2 2 4 Step 2 3 Angled Ceiling Only For Angled Ceilings Be sure to orient the hanger bracket with the large opening towards the ceiling peak Hunter Fan Company 3 Assembling and Hanging the Fan andara You can assemble your fan for standard or angle mounting as shown i Label ie Mounting in steps 3 1 3 6 For low profile mounting ceilings less than 8 feet Washer Qe high go to steps 3 7 3 11 on the next page 3 1 Remove the label from the standard mounting washer inside the canopy Leave the washer in place Note You will not use the washer included in the parts sack 3 2 To assemble fan to hang down from a flat or angled ceiling place the canopy with washer and canopy trim ring around the adapter so that they rest on the fan assembly 3 3 Feed the wires from the fan through the downrod 3 4 Screw the downrod into the fan assembly Tighten the square Step 3 1 Canopy head set screw A CAUTION The downrod has a special coating on the threads Steps 3 2 3 4 Do not remove this coating the
13. th three 8 32 x 1 2 screws 3 11 Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy Adapter Canopy Trim Ring A WARNING Fan may fall if not assembled as directed in these installation instructions 8 32 x 1 2 Screw Not Actual Size Step 3 10 Detail Low Profile Washer 42013 01 02 02 05 Hunter Fan Company 4 Wiring the Fan Wire Nut Hunter Fan Company All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 4 2 4 3 4 4 4 5 4 6 Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location Decide how you want to set up the fan and light controls You can control the fan and or lights together or separately using one or two wall switches Follow Step 4 3 OR Step 4 4 depending on what you decide If you want to you can control the fan and light separately using two wall switches connect the wires as follows e The bare or green ground wire from the ceiling to the green ground wire from the hanger bracket and the green ground wire from the fan e The white wire from the ceiling to the white w
Download Pdf Manuals
Related Search