Honeywell VCC-600N/P Digital Camera User Manual
Contents
1. SINSTRALLATION The contents of the package Check the below contents Mounting a lens 1 Remove the Protective cap in front of the camera 2 Confirm the mount ring whether it is for C or CS VCC 600N P Camera set 3 Attach the lens to the lens mount ring Auto Iris Lens Plug 4 If the lens has an Auto Iris mechanism connect the iris cable to the L Type Wrench LENS in rear of the camera Operation Manual English In the case of having no iris amplifier Set the slide switch to DC Down side In the case of having iris amplifier Set the slide switch VSD Upper side Xx When connecting Auto iris lens be sure to use the connector to be recommended by manufacturer E4 191 ChuoMusen Japan VSD LENS PIN CONFIGURATION DC IRIS LENS PIN CONFIGURATIO 3 4 3 4 er z 1 2 comm 1 2 QO _ A 1 Power 12V 2 No Connection 1 Control 2 Control 3 Video Signal 4 GND 3 Drive 4 Drive Back focus adjustment 1 In case of fixed focus lens Loosen the locking ring with L type wrench and set the focus ring of lens to infinity Tune the mount ring to get a clear picture distance from camera to object is more than 23m and fasten the locking ring 2 In case of zoom lens Loosen the locking ring with L type wrench and set the lens to the maximum telephoto position Then turn the focus ring to focus X In the case of Auto iris lens only shoot a comparatively dark object or r2. MODE Motion Petection made setting D ZOO Digital Zoom setting OFF gt 1 0x gt gt 16 0x ea IRROR Mirror mode setting OFF gt H MIRROR gt V MIRROR gt FLIP 61 WI x52 ALH x77 8 0 mm RETUR Return to the previous menu Pantone Colon ic Gray Gray SPECIAL SETUP SHARPNESS Sharpness compensation setting 0 15 Storage Temp ZOO TOC GAMMA Gamma compensation setting 0 36 1 USER 8steps Operating Humidity 90 RH non condensing LANGUAGE OSD Language setting ENG KOR JPN CHI1 CHI2 RETUR Return to the previous menu DEFAULT SETUP FACTORY DEFAULT Set to the Factory Default H il RETUR Return to the previous menu oneywe EXIT SETUP Honeywell Security Group SAVE AND EXIT Honeywell Co Ltd EXIT Address 5F Sangam IT Tower B4 4block 1590 RETURN Return to the previous menu Sangam dong Mapo gu Seoul 121 835 Republic of Korea TEL 82 2 799 6020 6395 6006 Printed in Korea FAX 82 2 792 9011 D 100073 001 REV O E mail info security honeywell com
3. Operation Manual OSD Color Camera VCC 600N P x Thank you for choosing Honeywell VCC 600N P camera Please read these instructions carefully before operating this unit and retain this manual for future reference If you have any problems with this camera contact your local supplier to service MQAUTION forSAFETY OPERATION 1 1 Water and Moisture To prevent fire or shock hazard do not expose this camera to rain or moisture 2 Servicing Do not attempt to disassemble or repair by yourself You may be exposed to dangerous voltage or other hazards Note that all servicing is qualified service personnel Modifications not approved by manufacturer could void the user s authority to operate the equipment 3 Power Sources To prevent electric shocks and risk of hazards do NOT use more than the specified power source 4 Environment Do not install too warm or too cold place Recommended operation temperature is between 5 C and 50 C 5 Sunlight Do not point the camera at the sun CCD can be damaged 6 Heavy Shock and Vibration Do not drop the camera or subject it to heavy shock of vibration 7 Install on an Unstable Place Do not place or install this camera on an unstable place stand tripod bracket or table That may cause serious injury to people or damage to appliance Before sending the camera out for repair check the items below If the problem persists after checking these items contact your service center In c
4. ase of no image Is the coaxial cable attached securely Are the power and voltage normal Has the iris of the lens inside the camera been adjusted correctly In case of unclear image Is the lens in focus Is the lens dirty Is the monitor adjusted correctly X Dirt of fingerprints on the lens can adversely affect the images Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid commercially available UNC 174 20 41 8 PF 12 7 8 When operation is incorrect or a malfunction is observed While operating if any abnormal condition strange sound smell or smoke or a malfunction no pictures etc is observed stop using the camera immediately turn the power off then contact your supplier 9 Cleaning Turn the power off and wipe off the dirt with a dry soft cloth If itis extremely dirty use furniture cleaner to wipe it off To clean the lens use a blower or lens cleaning tissue available from any camera dealer 10 Do not shoot any source of bright light If the objects contain very bright areas bright vertical or horizontal line
5. educe the ambient light so that the aperture is fully open 2 Set the lens to its maximum wide angle position and set the focus Repeat step and until the difference between focusing position and is smallest When the best focusing point in found fasten the locking ring Connection of power supply Must be checked the power source from the external power supply before power on VCC 600N VCC 600P GENERAL SETUP Operational SYNC SYNC LEVEL adjustment 0 gt 1 255 Video Standard NTSC PAL BURST BURST LEVEL adjustment 031 gt gt 255 Image Sensor SONY 1 3 Super HAD CCD CONTRAST CONTRAST LEVEL adjustment Total Pixel 410 000 Pixels 0313 100 Effective Pixel 380 000 Pixels RETURN Return to the previous menu Scanning System 525 Lines 2 1 Interlace Scanning Frequency 15 734kHz H 59 94Hz V CAMERA SETUP Sync System INTERNAL AE MODE LENS MODE SHUTTER AGC BRIGHTNESS MAX AGC AX FIELDS etc Bn ah cae 0 1 F 1 2 50IRE WB MODE AWC LOCK AWC AUTO ATW INDOOR OUTDOOR PO oie EPE NAKER EEA ANUAL etc PTP E EEP 7 their level area setting i a PZM SET Privacy Zone Masking function setting IGHTSHOT Day gt Night Night gt Day mode setting CAMERA ID Camera ID and Position setting RETURN Return to the previous menu MEM FUNC SETUP Electrical DNR MODE Digital Noise Reduction mode setting OFF gt LOWHIGH PIP MODE Picture in picture mode setting Mechanical amp Environmental oe a due d 2
6. s may appear on the screen This is called smear a Phenomenon which often occurs with solid state pickups andis nota malfunction 11 Damage Requiring service Unplug the camera from the power source and refer servicing to qualified service personnel under the following condition A If the power supply cord or plug is damaged B If the camera has been exposed to rain or water C If liquid has been spilled or objects have fallen into the camera D If the camera does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result indamage and will often require extensive work by a qualified technician to restore the camera to its normal operation E If the camera has been dropped or the cabinet has been damaged F If the camera exhibits a distinct change in performance G Warranty is not covered in case of natural disaster or wrong Installation UP BUTTON DOWN BUTTON ENTER BUTTON BUTTON BUTTON LENS CONNECTOR VIDEO OUTPUT Composite Video Signal Output POWER ON LED This LED is ON in power ON state Lens Type Select Switch DC Lens with no iris amp VSD Lens with iris amp Power Input Terminal and MD Alarm Output
Download Pdf Manuals
Related Search