Hitachi DZMV350A Camcorder User Manual
Contents
1. Caring for your appliance drum e Always leave the door ajar to prevent unpleasant odours from forming Cleaning the pump The washing machine is fitted with a self cleaning pump which does not require any maintenance Sometimes small items Such as coins or buttons may fall into the protective pre chamber at the base of the pump Make sure the wash cycle has finished and unplug the appliance To access the pre chamber 1 take off the cover panel on the front of the machine by first pressing it in the centre and then pushing downwards on both sides until you can remove it see figures 2 position a container so that it will collect the water which flows out approximately 1 5 see figure 3 unscrew the lid by rotating it in an anti clockwise direction see figure 4 clean the inside thoroughly 5 screw the lid back on 6 reposition the panel making sure the hooks are securely in place before you push it onto the appliance Checking the water inlet hose Check the inlet hose at least once a year If there are any cracks it should be replaced immediately during the wash cycles water pressure is very strong and a cracked hose could easily split open Precautions and tips The machine was designed and constructed in accordance with international safety regulations The following information is provided for safety reasons and must therefore be read carefully2. Before connecting the inlet hose to the water supply run the water until it is perfectly clear 1 Connect the inlet hose to the machine by screwing it onto the cold water inlet of the appliance which is situated on the top right hand side of the rear part of the appliance see figure 2 Connect the inlet hose by screwing it to a cold water tap using a 3 4 gas threaded connection see figure m mi 3 Make sure that the hose is not folded over or bent The water pressure at the tap must fall within the values indicated in the Technical data table see page 5 If the inlet hose is not long enough contact a specialised shop or an authorised technician T Never use second hand or old inlet hoses use the products supplied with the machine Connecting the drain hose Connect the drain hose without bending it toa draining duct or a wall drain situated between 65 and 100 cm from the floor The drain hose may be connected to an under sink trap Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot Where it connects to the waste water pipe cut end off spigot or remove the blanking cap If it is placed over the edge of a basin or sink be sure the free end of the hose should not be underwater We advise against the use of hose extensions in case of absolute need the extension must have the same diamet
3. General safety e This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Do not dry unwashed items in the tumble dryer Items that have been soiled with substances such as cooking oil acetone alcohol petrol Kerosene spot removers turpentine waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer Items such as foam rubber latex foam shower caps waterproof textiles rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer Fabric softeners or similar products should be used as specified by the fabric softener instructions The final part of a tumble dryer cycle occurs without heat cool down cycle to ensure that the items are left at a temperature that ensures that the items will not be damaged WARNING Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated e This appliance was designed for domestic use only e Do not
4. Press the button All the indicator lights will illuminate for 1 second and the text AQUALTIS will appear on the display the indicator light corresponding to the C button will then remain lit in a constant manner and the START PAUSE indicator light will flash 2 SELECT THE PROGRAMME Turn the PROGRAMME KNOB left or right until the required programme has been selected the name of the programme will appear on the display A temperature and spin speed is set for each programme these may be adjusted The cycle duration will also appear on the display 3 LOAD THE LAUNDRY Open the porthole door Load the laundry making sure you do not exceed the maximum load value indicated in the table of wash cycles on the following page 4 MEASURE OUT THE DETERGENT Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in Description of the machine 5 CLOSE THE PORTHOLE DOOR 6 CUSTOMISE THE WASH CYCLE Use the relevant buttons on the control panel Modify the temperature and or spin speed The machine automatically displays the maximum temperature and spin speed values set for the selected cycle or the most recently used settings if they are compatible with the selected cycle The temperature can be decreased by pressing the GY button until the cold wash OFF setting is reached The spin speed may be progressively reduced by pressing the button until it is completely exclu
5. balanced correctly the machine spins at a reduced spin speed If the load is excessively unbalanced the Washer dryer performs the distribution process instead of spinning To encourage improved load distribution and balance we recommend small and large garments are mixed in the load Disposal e Disposing of the packaging materials observe local regulations so that the packaging may be re used e The European Directive 2002 96 EC relating to Waste Electrical and Electronic Equipment WEEE states that household appliances should not be disposed of using the normal solid urban waste cycle Exhausted appliances should be collected separately in order to optimise the cost of re using and recycling the materials inside the machine while preventing potential damage to the atmosphere and to public health The crossed out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection For more information relating to the correct disposal of household appliances owners should contact their local authorities or appliance dealer Opening the porthole door manually In the event that it is not possible to open the porthole door due to a powercut and if you wish to remove the laundry proceed as follows 1 remove the plug from the electrical socket 2 make sure the water level inside the machine is lower than the door opening if it is not remove excess water using the drain hose colle
6. money back 15 195098434 01 09 2012 Xerox Fabriano After Sales Service No one is better placed to care for your Hotpoint appliance during the course of its working life than us the manufacturer Essential Contact Information Hotpoint Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast reliable local service UK 08448 224 224 Republic of Ireland 0818 313 413 www hotpointservice co uk Please note Our advisors will require the following information Model number E Serial number Parts and Accessories We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life UK 08448 225 225 Republic of Ireland 0818 313 413 www hotpointservice co uk Appliance Registration We want to give you additional benefits of Hotpoint ownership To activate your free 5 year parts guarantee you must register your appliance with us UK 08448 24 24 24 Republic of Ireland 01 230 0800 www hotpointservice co uk Indesit Company UK Ltd Morley Way Peterborough PE2 9JB Indesit Company Unit 49 Airways Industrial Estate Dublin 17 D Recycling amp Disposal Information As part of Hotpoint s continued commitment to helping the environment Hotpoint reserv
7. off If the selected option is not compatible with the selected wash cycle this incompatibility will be signalled by the flashing of the indicator light and a sound alert 3 beeps the option will not be activated If the selected option is not compatible with another option that has been selected previously the indicator light corresponding to the first option selected will flash and only the second option will be activated the indicator light corresponding to the button will remain lit in a constant manner The options may affect the recommended load value and or the duration of the cycle 7 START THE PROGRAMME Press the START PAUSE button The corresponding indicator light remains lit in a fixed manner and the porthole door locks the LOCK indicator light illuminates The icons corresponding to the wash cycle phases will light up during the cycle to indicate which phase is currently in progress To change a wash cycle once it has already started pause the Washer dryer by pressing the START PAUSE button then select the desired cycle and press the START PAUSE button again To open the door during a wash cycle press the START PAUSE button if the LOCK 8 indicator light is switched off you may open the door Press the START PAUSE button again to restart the wash cycle from the point at which it was interrupted 8 THE END OF THE WASH CYCLE This is indicated by the illuminated text END The porthole door may be opene
8. the formation of creases At the end of the cycle the washing machine drum will rotate slowly the Easy Iron and START PAUSE indicator lights will flash To end the cycle press the START PAUSE button or the Easy Iron button It cannot be used in conjunction with T gt amp 3 Note If you also want to run the drying cycle this option is enabled only if combined with level Iron amp Time Saver If you select this option the wash cycle duration will be reduced by up to 50 depending on the selected cycle thereby guaranteeing simultaneous water and energy saving Use this cycle for lightly soiled garments It cannot be used in conjunction with F F amp amp SD GB Op Ay A Eco The Eco Option saves energy by not heating the water used to wash your laundry an advantage both to the environment and to your energy bill Instead intensified wash action and water optimisation ensure great wash results in the same average time of a standard cycle For the best washing results we recommend the usage of a liquid detergent It cannot be used in conjunction with F F gt amp SS SH BO Je 11 Detergents and laundry Detergent The type and quantity of detergent required depend on the type of fabric you are washing cotton wool silk etc as well as its colour the washing temperature the level of soiling and the hardness of the water in the area Measuring out the dete
9. touch the machine when barefoot or with wet or damp hands or feet e Do not pull on the power supply cable when unplugging the appliance from the electricity socket Hold the plug and pull e Do not touch the drained water as it may reach extremely high temperatures e Never force the porthole door This could damage the safety lock mechanism designed to prevent accidental opening e f the appliance breaks down do not under any circumstances access the internal mechanisms in an attempt to repair it yourself e Always keep children well away from the appliance while it is operating e f it must be moved proceed with the help of two or three people and handle it with the utmost care Never try to do this alone because the appliance is very heavy e Before loading laundry into the washer dryer make sure the drum is empty e During the drying phase the door tends to get quite hot e Do not use the appliance to dry clothes that have been washed with flammable solvents e g trichlorethylene e Do not use the appliance to dry foam rubber or similar elastomers e Make sure that the water tap is turned on during the drying cycles E Hotpoint Load balancing system Before every spin cycle to avoid excessive vibrations before every spin and to distribute the load in a uniform manner the drum rotates continuously at a speed which is slightly greater than the washing rotation speed If after several attempts the load is not
10. Instructions for installation and use WASHER DRYER T Lu This symbol reminds you to read this instruction manual EN EN Contents English 1 Installation 2 3 4 5 Unpacking and levelling Connecting the electricity and water supplies Technical data Care and maintenance 6 Cutting off the water and electricity supplies Cleaning the machine Cleaning the detergent dispenser drawer Caring for your appliance drum Cleaning the pump Checking the water inlet hose Precautions and advice 7 General safety AQUALTIS Load balancing system Disposal AQD1170D 697 E Opening the porthole door manually AQD1170D 697 Description of the machine 8 9 Touch control panel How to run a wash cycle or a drying cycle 10 Wash cycles and options 11 Table of wash cycles Wash options Detergents and laundry 12 Detergent Preparing the laundry Washing recommendations Trouble shooting 13 14 Assistance 15 E Hotpoint Installation This instruction manual should be kept in a safe place for future reference If the washing machine is sold given away or moved please ensure the manual is kept with the machine so that the new owner may benefit from the advice contained within it Read these instructions carefully they contain vital information relating to the safe installation and operation of the appliance Inside the pack containing this manual you will also find the guarantee and all the details necessary fo
11. a drying cycle G 4s in accordance with the type of fabric The desired drying level or time may also be set using the DRYING button 20 Setting a delayed start To set a delayed start for the selected cycle press the corresponding button repeatedly until the required delay period has been reached During the setting procedure the delay period and the text Starts in will be displayed along with the flashing symbol After the delayed start has been set the symbol will remain fixed on the display which will also indicate the duration of the selected cycle with the text Ends in and the cycle duration Press the DELAYED START button just once to display the delay time set previously After the countdown has begun the display will show the text Starts in and the delay period Once the set delay time has elapsed the machine will begin its cycle and the display will show Ends in and the time remaining until the end of the cycle To remove the delayed start option press the button until the display shows the text OFF the 7 symbol will disappear Modify the cycle settings e Press the button to activate the option the name of the option will then appear on the display and the corresponding indicator light will illuminate e Press the button again to deactivate the option the name of the option will then appear on the display followed by the text OFF and the corresponding indicator light will switch
12. adaptor or at the distribution board If you are in any doubt regarding the electrical supply to your machine consult a qualified electrician before use How to connect an alternative plug The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN amp YELLOW EARTH E GREEN amp YELLOW gt Sh BROWN mom I aje 13 ampere fuse EE petted tol aed p Sei ta BLUE CROSS BAR CORD GRIP Disposing of the appliance When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described on the previous page The washing machine should not be installed in an outdoor environment not even where the area is sheltered because it may be very dangerous to leave it exposed to damp rain and thunderstorms When the washing machine is installed the mains socket must be within easy reach Do not use extensions or multiple sockets The power supply cable must never be bent or dangerously compressed The power supply cable must only be replaced by an authorised serviceman Warning The company denies all liability if and when these norms are not respected E Hotpoint Technical data EN AQD1170D 697 E Model AQD1170D 697 width 59 5 cm Dimensions height 85 cm depth 64 5 cm from 1 to 11 kg for the wash programme from 1 to 7 kg for the d
13. ccessory These include but are not limited to plugs cables batteries light bulbs fluorescent tubes and starters covers and filters Replacement of any removable parts made of glass or plastic THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON DOMESTIC PREMISES 5 Year Parts Guarantee Hotpoint also offers you a free 5 year parts guarantee This additional guarantee is conditional on you registering your appliance with us and the parts being fitted by one of our authorised engineers There will be a charge for our engineer s time To activate the extra parts warranty on your appliance simply call our registration line on 08448 24 24 24 ROI 01 230 0800 Extended Guarantees We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the life of your policy To find the ideal plan for you please call our advice line on 08448 226 226 Republic of Ireland 01 230 0233 Free Helpdesk Service We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical difficulties within the first 90 days of ownership Simply call our Hotpoint Service Hotline on 08448 224 224 Republic of Ireland 0818 313 413 for telephone assistance or where necessary to arrange for an engineer to call If we cannot resolve the technical problem we will replace your machine or if you prefer give you your
14. cordingly see The machine wont spin properly below Most Common Cause The display time is for guidance only itis not a precise time to finish and may vary The feet have not been adjusted enabling the machine to rock New Installation Either the Transit Bolts including the plastic spacers or the Polystyrene Packaging have not been removed when installing the machine The machine is trapped between cabinets and or walls The load is in a slight out of balance condition and machine is spinning but at a lower speed 13 The machine is noisy The machine wont spin properly The machine leaks from the dispenser The machine leaks other than dispenser The Phase in Progress indicator lights flash rapidly at the same time as the ON OFF indicator light The machine smells The machine door cannot be opened Door Seal damaged at the bottom The water level is too low when the machine is washing The word DEMO appears intermittently in the display window and the drum slowly turns The machine just beeps when a programme or option is selected Child Lock Symbol is lit Clothes are coming out too wet on Steam Refresh cycle There is too much foam After completing the programme or before starting a programme the machine has turned itself off no lights General There will always be some motor pump and drum noise during spin Out of Balance detected w
15. cting it in a bucket as indicated in the figure 3 remove the cover panel on the lower front part of the washer dryer See overleaf 4 pull outwards using the tab as indicated in the figure until the plastic tie rod is freed from its stop position pull downwards until you hear a click which indicates that the door is now unlocked 5 open the door if this is still not possible repeat the procedure 6 reposition the panel making sure the hooks are securely in place before you push it onto the appliance Description of the machine PORTHOLE DOOR PORTHOLE DOOR HANDLE Always use the handle to open the porthole door see figure DETERGENT DISPENSER DRAWER NN The detergent dispenser drawer is located inside the machine and can be accessed by opening the door For more information on detergent measures please refer to the chapter entitled Detergents and laundry Do not pour detergent into the compartment 1 Detergent should only be poured into the compartment 2 2 main wash compartment If liquid detergent is used it is recommended that the removable plastic partition A supplied be used for proper dosage lf powder detergent is used place the partition into slot B CONTROL PANEL amp washing additives compartment for fabric softener or liquid additives We recommend that the maximum level indicated by the grille is not exceeded and that conce
16. d immediately If the START PAUSE indicator light is flashing press the button to end the cycle Open the door unload the laundry and switch off the machine If you wish to cancel a cycle which has already begun press and hold the button until the cycle stops and the machine switches off Wash cycles and options Table of wash cycles E Hotpoint a Detergent and y ax additives ax Icon Description of the wash cycle Max temp speed Drying load Cycle C Fabric duration rpm Wash kg softener Te Cotton Coloureds 2 lightly soiled whites and delicate colours 40 1600 o o e 11 a A Synthetics Resistant 60 800 5 z A Synthetics Resistant 4 40 800 e 5 2 T Whites 60 1600 o 6 2 Coloureds 3 40 1600 o e 6 3 F Darks 30 800 o 6 ED Steam Refresh z z 2 2 3 Wool Platinum Care for wool cashmere etc 40 800 o e e 2 5 lt 4 Ultradelicates 30 0 1 3 Rinse 1600 e 11 S fad 3 Spin and Pump out z 1600 e 2 11 F Wash amp Dry 30 1600 e e 1 9 T Drying Cottons 5 z 7 Q By Drying Wool J 2 5 Q 4 Drying Synthetics z G 5 a Q Tee Cotton Whites extremely soiled whites and resistant colours 90 1600 e 11 g Tee Cotton Whites 1 heavily soiled whites and resistant colours 60 1600 o 11 g The length of cyc
17. ded OFF If these buttons are pressed again the maximum values are restored Setting the drying cycle The first time the button lt is pressed the machine will automatically select the maximum drying cycle which is compatible with the selected wash cycle Subsequent presses will decrease the drying level and then the drying time until the cycle is excluded completely OFF If these buttons are pressed again the maximum values are restored Drying may be set as follows A Based on a set time period between 20 and 180 minutes B Based on the desired laundry dryness level lron suitable for clothes which will need ironing afterwards the remaining dampness softens creases making them easier to remove Hanger ideal for clothes which do not need to be dried fully Cupboard suitable for laundry which can be put back in a cupboard without being ironed Extra suitable for garments which need to be dried completely such as sponges and bathrobes If your laundry load to be washed and dried is much greater than the maximum stated load perform the wash cycle and when the cycle is complete divide the garments into groups and put some of them back in the drum At this point follow the instructions provided for a Drying only cycle Repeat this procedure for the remainder of the load A cooling down period is always added to the end of each drying cycle 10 Drying only Use the cycle selector knob to select
18. e of wash cycles The knob will not move during the wash cycle M1 M2 buttons press and hold one of the buttons to store a cycle with your own set preferences in the memory of the machine To recall a previously stored cycle press the corresponding button DRYING button zO press to decrease or exclude drying the selected drying level or time will appear on the display see How to run a wash cycle or a drying cycle TEMPERATURE a button press to modify or exclude the temperature setting the value selected will appear on the display above see How to run a wash cycle or a drying cycle SPIN CYCLE button press to modify or exclude the spin cycle the value selected will appear on the display above see How to run a wash cycle or a drying cycle DELAYED START e button press to set a delayed start for the selected wash cycle the set delay time will appear on the display above see How to run a wash cycle or a drying cycle OPTION buttons press to select the available options The indicator light corresponding to the selected option will remain lit see How to run a wash cycle or a drying cycle LOCK indicator light WASH CYCLE PHASE icons these illuminate to indicate the progress of the wash cycle Wash s Rinse amp y Spin Drain Drying 503 The text END lights up when the cycle is complete START PAUSE button with indicator light when the green indicator light f
19. er as the original hose and must not exceed 150 cm in length Ensure that if the drain hose is pushed into a standpipe that the end does not go down more than 15cms 6 inches If the hose is pushed down too far this may cause the machine to self syphon ie continuously empty as it is filling Electric connection Before plugging the appliance into the mains socket make sure that e the socket is earthed and in compliance with the applicable law e the socket is able to sustain the appliance s maximum power load indicated on the Technical Data Plate fixed on the machine e the supply voltage is included within the values indicated on the Technical Data Plate fixed on the machine E Hotpoint e the socket is compatible with the washing machine s plug If this is not the case replace EN the socket or the plug Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please read the instructions below WARNING THIS APPLIANCE MUST BE EARTHED THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN Replacing the fuse When replacing a faulty fuse a 13 amp ASTA approved fuse to BS 1362 should always be used and the fuse cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacement fuse covers If a replacement fuse cover is fitted it must be of the c
20. es not drain or spin error lights flashing The machine does not spin The machine does not drain or spin EASY IRON light flashes The programme takes too long The Display sticks at one time to end for more than 1 Minute or the Display changes the estimated Time to End during the programme The machine vibrates a lot during the spin cycle E Hotpoint Possible causes Solutions e The appliance is not plugged into the socket fully or not enough to make contact e There is no power to the socket or the fuse has blown in the mains plug e The door is not closed properly e The ON OFF button has not been pressed e The START PAUSE button has not been pressed e The water tap has not been turned on to allow water to flow into the machine e The DELAY TIMER has been selected e The CHILD LOCK is activated see The machine just beeps when a programme or option is selected below e Check the 2 sections above e The DRY button has been pressed to exclude drying e A cooling down period is always added to the end of each drying cycle If the clothes appear too hot to handle leave the door open to allow to cool further before removing from the machine The water inlet hose is kinked The water inlet hose is not connected to the water supply The water pressure is too low The water tap has not been turned on to allow water to flow into the machine There is no wa
21. es the right to use quality recycled components to keep down customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise the risk of injury to children remove the door plug and cut the mains cable off flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door 16
22. ghtness of white clothes over time If the drying function is selected a drying cycle automatically activates at the end of the wash cycle that resembles open air drying with the added advantages of preserving garments from yellowing due to sunlight exposure and preventing loss of whiteness caused by the possible presence of dust in the air Drying cycles can only be selected on a level basis Coloureds use this cycle 4 to wash bright coloured clothes The programme is designed to maintain bright colours over time Darks use cycle f to wash dark coloured garments This programme is designed to maintain dark colours over time We recommend using a liquid detergent for the best results when washing dark coloured garments When you select the drying function at the end of the washing cycle the machine will automatically perform a delicate drying cycle that preserves the colours of the garments The display will show the level Hanger Max load 3 kg 12 Steam Refresh this programme refreshes garments by removing bad odours and relaxing the fibres 2 kg roughly 3 items Insert dry items only that are not dirty and select programme 5 The garments will be damp once the cycle is completed so we recommend hanging them to 9 programme makes ironing easier Moreover with the Steam Perfume laundry balls your favourite perfume can be added to your laundry Place a few drops of perfume on the sponge contained in
23. hen attempting to go into a spin cycle If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds This will increase the programme time accordingly This is a safety feature to prevent damage Out of Balance can be caused by washing a single heavy item eg duvet quilt etc Try the programme again using a different load The dispenser drawer is blocked with detergent and requires cleaning The water pressure is too high and requires turning down turn down the tap on the water supply pipe slightly and try again The machine is tilting forwards It must be level when in its final position The fill hose is loose check both the cabinet and tap ends The fill hose is tight but still leaks if so replace the rubber washers or the fill hose is missing the rubber washer The drain hose is not fixed in properly Switch off the machine and unplug it wait for approximately 1 minute and then switch back on again If the problem persists contact Technical Assistance Centre The machine requires a service wash Run a 90 degree wash cycle with detergent and no laundry The door will not open until the door lock indicator light goes out shortly after the program has finished If there is no power to the machine you need to perform the manual unlocking procedure see Precautions amp Tips The door seal has drainage holes at the bottom This is
24. items which do not have a wash label or wash items that are not intended as machine washable 14 Assistance Hotpoint Guarantee EN 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer s guarantee which covers the cost of breakdown repairs for twelve months from the date of purchase This gives you the reassurance that if within that time your appliance is proven to be defective because of either workmanship or materials we will at our discretion either repair or replace the appliance at no cost to you This guarantee is subject to the following conditions The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions The appliance is used only on the electricity or gas supply printed on the rating plate The appliance has been used for normal domestic purposes only The appliance has not been altered serviced maintained dismantled or otherwise interfered with by any person not authorised by us Any repair work must be undertaken by us or our appointed agent Any parts removed during repair work or any appliance that is replaced become our property The appliance is used in the United Kingdom or Republic of Ireland The guarantee does not cover Damage resulting from transportation improper use neglect or interference or as a result of improper installation Replacement of any consumable item or a
25. lashes slowly press the button to start a wash cycle Once the cycle has begun the indicator light will remain lit in a fixed manner To pause the wash cycle press the button again the indicator light will flash in an orange colour If the LOCK indicator light is switched off the door may be opened To start the wash cycle from the point at which it was interrupted press the button again LOCK indicator light indicates that the porthole door is locked To open the door pause the wash cycle see How to run a wash cycle or a drying cycle CHILD LOCK button with indicator light to activate or deactivate the CHILD LOCK press and hold the button for approximately 2 seconds when the indicator light is illuminated the control panel is locked This means it is possible to prevent wash cycles from being modified accidentally especially where there are children in the home ECO indicator light the ECO icon lights up when after altering the washing parameters an energy saving of at least 10 is made Furthermore before the machine enters Standby mode the icon will light up for a few seconds when the machine is switched off the estimated energy saving will be around the 80 mark How to run a wash cycle ora drying cycle WARNING before you use the Washer dryer for the first time run a wash cycle with detergent and no laundry using the 90 cottons cycle without pre wash 1 SWITCH THE MACHINE ON
26. le shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions The actual duration can vary according to factors such as water temperature and pressure the amount of detergent used the amount and type of load inserted load balancing and any wash options selected Note 10 minutes after the START the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it this value will then be shown on the display For all Test Institutes 1 Test wash cycle in compliance with regulation EN 50229 set wash cycle T with a temperature of 60 C 2 Long wash cycle for cottons set wash cycle T with a temperature of 40 C 3 Short wash cycle for cottons set wash cycle w with a temperature of 40 C 4 Long wash cycle for synthetics set wash cycle A with a temperature of 40 C Wash options 2 Steam Hygiene This option enhances washing performance by generating steam during the wash cycle that eliminates any bacteria from fibres while treating them at the same time Place the laundry in the drum choose a compatible programme and select option gp The steam generated during washing machine operation may cause the porthole door to become hazy It cannot be used in conjunction with F T amp amp Ey D He TE D Bis Tar Easy Iron By selecting this option the wash and spin cycles will be modified in order to reduce
27. normal The water level is correct if it can be seen at the bottom of the door To exit switch machine off then press and hold START PAUSE and ON OFF buttons simultaneously for 3 seconds Note the machine will need the language resetting Deactivate the Child Lock feature by pressing and holding in the CHILD LOCK button for 2 seconds Only dry items are to be used for this program The program refreshes garments by removing bad odours and relaxing the fibres also making items easier to iron if required The detergent is not suitable for machine washing it should display the text for washing machines or hand and machine wash or the like Too much detergent was used less detergent is required in soft water To comply with new energy saving regulations the machine is fitted with an automatic standby system Press ON OFF button for 3 seconds to activate the machine it can then either be switched off or a new programme selected Your washing machine contains sensors that monitor progress during the wash cycle eg Water Levels Temperatures Out of Balance loads Wash time progress Normally if your machine successfully completes the cycle there is unlikely to be anything wrong Remember you will be charged for a service call for problems caused by incorrect installation as listed above Not emptying contents from pockets may cause pump or drain blockages or may damage the machine Do not wash
28. ntrated fabric softeners are diluted TOUCH CONTROL PANEL To adjust the settings gently press the icon inside the a sensitive touch control area as illustrated in the figure Standby mode This washing machine in compliance with new energy saving regulations is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected Press the ON OFF button briefly and wait for the machine to start up again Consumption in off mode 0 5 W Consumption in Left on 0 5 W E Hotpoint START PAUSE button Touch control panel SPIN with indicator ight WASH EN button CYCLE WASH CYCLE M1 ECO PHASE SELECTOR knob piace ion indicator _ DISPLAY m OPTION CHILD LOCK Button with ON OFF DRYING pues DELAYED START button with indicator light indicator light button button Button with ON OFF indicator light press this briefly to switch the machine on or off The green indicator light indicates that the machine is switched on To switch off the Washer dryer during the wash cycle press and hold the button for approximately 3 seconds if the button is pressed briefly or accidentally the machine will not switch off If the machine is switched off during a wash cycle this wash cycle will be cancelled WASH CYCLE SELECTOR knob may be turned in either direction To select the most suitable wash cycle please refer to the Tabl
29. orrect colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug Replacements can be obtained directly from your nearest Service Depot Removing the plug If your appliance has a non rewireable moulded plug and you should wish to re route the mains cable through partitions units etc please ensure that either the plug is replaced by a fused 13 ampere rewireable plug bearing the BSI mark of approval Or the mains cable is wired directly into a 13 amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Ensure that before disposing of the plug itself you make the pins unusable so that it cannot be accidentally inserted into a socket Instructions for connecting cable to an alternative plug Important the wires in the mains lead are coloured in accordance with the following code Green amp Yellow Earth Blue Neutral Brown Live As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug proceed as follows Connect Green amp Yellow wire to terminal marked E or or coloured Green or Green amp Yellow Connect Brown wire to terminal marked L or coloured Red Connect Blue wire to terminal marked N or coloured Black Ifa 13 amp plug BS 1363 is used it must be fitted with a 13 amp fuse either in the plug or
30. r installation Unpacking and levelling Unpacking 1 Once you have removed all the packaging from the washing machine make sure it has not been damaged during transportation If it has been damaged contact the retailer and do not proceed any further with the installation process 2 Remove the 4 protective screws used during transportation and the corresponding spacer located on the rear part of the appliance see figure 3 Close off the holes using the plastic plugs supplied in the pack 4 Keep all the parts in a safe place they will be needed again if the washing machine is moved to another location to prevent the inside of the appliance being damaged Packaging materials should not be used as toys for children Levelling 1 Place the washing machine on a flat sturdy floor without resting it up against walls cabinets anything else 2 If the floor is uneven the front feet of the machine may be adjusted until it reaches a horizontal position the angle of inclination must not exceed 2 degrees If the appliance is levelled correctly it will be more stable and much less likely to cause vibrations and noise while it is operating particularly during the spin cycle If it is placed on carpet or a rug adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine Connecting the electricity and water supplies Connecting the water inlet hose
31. rgent carefully will avoid wastage and help to protect the environment although they are biodegradable detergents still contain ingredients which alter the balance of nature We recommend the following e use powder detergents for white cotton garments and pre washing e use liquid detergents for delicate cotton garments and for all low temperature wash cycles e use gentle liquid detergents for wool and silk garments The detergent should be poured into the relevant compartment or the dispenser placed directly inside the drum before the wash cycle begins In the latter case it will not be possible to select the Cottons with pre wash cycle Do not use hand washing detergents because these create too much foam Preparing the laundry Shake out the garments before loading them into the machine e Divide the laundry according fabric type symbol on the washing instruction label and colour making sure you separate the coloured garments from the white ones e Empty all pockets and check the buttons e Do not exceed the values listed in the Table of wash cycles which refer to the weight of the laundry when dry How much does your laundry weigh 1 sheet 400 500 g 1 pillowcase 150 200 g 1 tablecloth 400 500 g 1 bathrobe 900 1200 g 1 towel 150 250 g 1 pair of jeans 400 500 g 1 shirt 150 200 g Washing recommendations Whites use this cycle 7 to wash white clothes The programme is designed to maintain the bri
32. rying programme please refer to the technical data plate fixed to the ma chine maximum pressure 1 MPa 10 bar minimum pressure 0 05 MPa 0 5 bar drum capacity 71 litres Capacity Electrical connections Water con nections up to 1600 rotations per minute Spin speed Wash programme 7 tem perature 60 C using a load of 11 kg evra ra Drying the smaller load must be dried by selecting Co eording to the EXTRA dryness level requilatl ted The load must consist of 3 EN 50229 sheets and 7 pillowcases the remainder of the load must be dried by selecting the EXTRA dryness level This appliance conforms to the following EC Directives 2004 108 EC Electromagne tic Compatibility 2006 95 EC Low Voltage 2002 96 EC Care and maintenance Cutting off the water and electricity supplies e Turn off the water tap after every wash cycle This will limit wear on the hydraulic system in the machine and help to prevent leaks e Unplug the appliance when cleaning it and during all maintenance work Cleaning the machine The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water Do not use solvents or abrasives Cleaning the detergent dispenser drawer To remove the drawer press lever 1 and pull the drawer outwards 2 see figure Wash it under running water this procedure should be repeated frequently
33. side the laundry ball close it and insert it into the drum together with the laundry Then launch the specific programme sp At the end of the cycle garments will be relaxed and fragrant Not recommended for wool or silk garments Do not add too much perfume to the sponge in order to avoid it dripping Do not add softeners or detergents Wool the wool wash cycle on this Hotpoint machine has been tested and approved by The Woolmark Company for washing wool garments labelled as hand washable provided that the garments are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine Hotpoint is the first washing machine brand to be approved by The Woolmark Company for Apparel Care Platinum for its washing performance and consumption of energy and water M1135 WOOLMARK APPAREL CARE Ultradelicates use programme y to wash very delicate garments having strasses or sequins We recommend turning the garments inside out before washing and placing small items into the special bag for washing delicates Use liquid detergent on delicate garments for best results To wash Silk garments and Curtains select cycle amp 4 and then option the machine will end the cycle while the laundry is soaking and the amp indicator light will flash To drain the water so that the laundry may be removed press the START PAUSE button or the amp button When selec
34. ter supply to the house The inlet valve filter is blocked The START PAUSE button has not been pressed The top of the drain hose is too low It must be fitted at a height between 65 and 100 cm from the floor see Installation The drain hose is connected incorrectly to the sink trap allowing water to run into the machine the drain hose must be positioned higher than the bottom of the sink to prevent water flowing down the drain hose The end of the drain hose has been pushed too far down the standpipe the U bracket should be fitted 100 mm from the end of the drain hose The Pump filter is blocked The drain hose is kinked see Installation New Installation The blanking cap or spigot has not been removed if connected under a sink The drain hose or sink trap is blocked The Spin Speed is set to OFF position The EASY IRON option is enabled at the end of the program the machine drum will rotate slowly To complete the wash cycle press the START PAUSE or the EASY IRON buttons see Wash Cycles amp Options Programme times will vary due to water pressure the incoming water temperature and if the wash load goes out of balance This will increase the programme times accordingly see The machine wont spin properly below Programme times will vary due to water pressure the incoming water temperature and if the wash load goes out of balance This will increase the programme time ac
35. ting an exclusively time based drying function a drying cycle is performed at the end of the wash cycle that is particularly delicate thanks to light handling and appropriate temperature control of the water jet The recommended durations are 1 kg of synthetic garments gt 160 min 1 kg of synthetic and cotton garments gt 180 min 1 kg of cotton garments gt 180 min The degree of dryness depends on the load and fabric composition Wash amp Dry was designed to wash and dry lightly soiled garments quickly This cycle may be used to wash and dry a laundry load of up to 1 kg in just 45 minutes To achieve optimum results use liquid detergent and pre treat cuffs collars and stains Stubborn stains it is wise to treat stubborn stains with solid soap before washing and to use the Cottons with pre wash cycle Trouble shooting Your washing machine could occasionally fail to work Before contacting the Technical Assistance Centre see Assistance make sure that the problem cannot be solved easily using the following list Problem The machine does not switch on The wash cycle does not start The machine does not dry The clothes are too hot when the drying cycle is finished The machine does not fill with water or Indicator light for the first wash cycle flashing rapidly The machine continuously fills with water and continually drains away or Water left in the drum or Stuck on wash The machine do
Download Pdf Manuals
Related Search