Alcatel-Lucent 6300-24 Switch User Manual
Contents
1. Table 4 3 Maximum 1000BASE LX Gigabit Ethernet Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 9 125 micron N A 2m 5km 7 ft 3 2 miles LC single mode fiber 4 4 Connectivity Rules 4 100 Mbps Fast Ethernet Collision Domain Table 4 4 Maximum Fast Ethernet Cable Distance Type Cable Type Max Cable Length Connector 100BASE TX Category 5 or better 100 ohm UTP or STP 100 m 328 ft RJ 45 10 Mbps Ethernet Collision Domain Table 4 5 Maximum Ethernet Cable Distance Cable Type Maximum Length Connector Twisted Pair Categories 3 4 5 or better 100 m 328 ft RJ 45 100 ohm UTP 4 5 4 Making Network Connections Cable Labeling and Connection Records When planning a network installation it is essential to label the opposing ends of cables and to record where each cable is connected Doing so will enable you to easily locate inter connected devices isolate faults and change your topology without need for unnecessary time consumption To best manage the physical implementations of your network follow these guidelines e Clearly label the opposing ends of each cable Using your building s floor plans draw a map of the location of all network connected equipment For each piece of equipment identify the devices to which it is connected Note the length of each cable and the maximum cable length supported by the2. A 1000 Mbps network communication system based on Ethernet and the CSMA CD access method Full Duplex Transmission method that allows two network devices to transmit and receive concurrently effectively doubling the bandwidth of that link IEEE Institute of Electrical and Electronic Engineers IEEE 802 3 Defines carrier sense multiple access with collision detection CSMA CD access method and physical layer specifications IEEE 802 3ab Defines CSMA CD access method and physical layer specifications for 1000BASE T Gigabit Ethernet IEEE 802 3u Defines CSMA CD access method and physical layer specifications for 100BASE TX Fast Ethernet IEEE 802 3x Defines Ethernet frame start stop requests and timers used for flow control on full duplex links IEEE 802 3z Defines CSMA CD access method and physical layer specifications for 1000BASE Gigabit Ethernet LAN Segment Separate LAN or collision domain Glossary 2 Glossary LED Light emitting diode used for monitoring a device or network condition Local Area Network LAN A group of interconnected computer and support devices Media Access Control MAC A portion of the networking protocol that governs access to the transmission medium facilitating the exchange of data between network nodes An acronym for Management Information Base It is a set of database objects that contains information about the device Network Diameter Wire distance between two end
3. Ethernet and Gigabit Ethernet installations where significant growth is expected in the near future You can easily build on this basic configuration adding direct full duplex connections to workstations or servers When the time comes for further expansion just connect to another hub or switch using one of the Gigabit Ethernet ports built into the front panel or a Gigabit Ethernet port on a plug in SFP transceiver In the figure below this switch is operating as a collapsed backbone for a small LAN It is providing dedicated 10 Mbps full duplex connections to workstations and 100 Mbps full duplex connections to power users and 1 Gbps connections to servers Servers Workstations Workstations 1 Gbps 100 Mbps 10 Mbps Full Duplex Full Duplex Full Duplex Figure 2 1 Collapsed Backbone 2 2 Application Examples 2 Network Aggregation Plan With 24 parallel bridging ports i e 24 distinct collision domains the Gigabit Ethernet Switch can collapse a complex network down into a single efficient bridged node increasing overall bandwidth and throughput In the figure below the 10 100 1000BASE T ports on the Gigabit Ethernet Switch are providing 1000 Mbps connectivity for up to 24 segments through stackable switches In addition the switch is also connecting several servers at 1000 Mbps SOO COCO COCO r lt
4. 14 15 Bitte lesen Sie diese Hinweise sorgfaltig durch Heben Sie diese Anleitung f r den spateren Gebrauch auf Vor jedem Reinigen ist das Gerat vom Stromnetz zu trennen Verwenden Sie keine Fl ssigoder Aerosolreiniger Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung Die Netzanschlu Rsteckdose soll nahe dem Ger t angebracht und leicht zug nglich sein Das Ger t ist vor Feuchtigkeit zu sch tzen Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Besch digungen hervorrufen Die Bel ftungs ffnungen dienen der Luftzirkulation die das Ger t vor berhitzung sch tzt Sorgen Sie daf r da diese ffnungen nicht abgedeckt werden Beachten Sie beim Anschlu an das Stromnetz die Anschlu werte Verlegen Sie die Netzanschlu leitung so da niemand dar ber fallen kann Es sollte auch nichts auf der Leitung abgestellt werden Alle Hinweise und Warnungen die sich am Ger t befinden sind zu beachten Wird das Ger t ber einen l ngeren Zeitraum nicht benutzt sollten Sie es vom Stromnetz trennen Somit wird im Falle einer berspannung eine Besch digung vermieden Durch die L ftungs ffnungen d rfen niemals Gegenst nde oder Fl ssigkeiten in das Ger t gelangen Dies k nnte einen Brand bzw elektrischen Schlag ausl sen ffnen sie niemals das Ger t Das Ger t darf aus Gr nden der elektrischen Sicherheit nur von authorisiertem Servicepersonal ge ffnet
5. 4 console port pin assignments 3 6 contents of package 3 2 cooling problems A 1 cord sets international 3 6 D DC input 1 5 desktop mounting 3 4 device connections 4 1 E EC conformance 1 v electrical interference avoiding 3 1 EMC safety compliance 1 v equipment checklist 3 2 Ethernet connectivity rules 4 5 F Fast Ethernet connectivity rules 4 4 4 5 FCC compliance 1 v features management 1 6 switch 1 5 fiber cables 4 3 full duplex connectivity 2 1 G Gigabit Ethernet cable lengths 4 4 grounding for racks 3 3 I IEEE 802 3 Ethernet 1 5 IEEE 802 3u Fast Ethernet 1 5 IEEE 802 3z Gigabit Ethernet 1 5 indicators LED 1 3 installation connecting devices to the switch 4 1 desktop or shelf mounting 3 4 port connections 4 1 power requirements 3 1 problems A 1 rack mounting 3 3 site requirements 3 1 wiring closet connections 4 2 Introduction 2 1 Index 1 laser safety 4 3 LED indicators BPS 1 4 Diag 1 4 FDX 1 3 Link 1 3 Power 1 4 location requirements 3 1 M management agent 1 1 features 1 6 C 2 out of band 1 1 SNMP 1 1 Web based 1 2 mounting the switch inarack 3 3 on a desktop or shelf 3 4 multimode fiber optic cables 4 3 N network connections 4 1 examples 2 2 O optional backup power supply 1 5 out of band management 1 1 P package contents 3 2 pin assignments B 1 console port 3 6 DB 9 3 6 port based VLANs 2 5 ports connecting to 4 1 power connecting to 3 6 Index 2 R rack
6. Gigabit Ethernet over 100 ohm Category 5 5e or 6 twisted pair cable using all four wire pairs Auto Negotiation Signalling method allowing each node to select its optimum operational mode e g speed and duplex mode based on the capabilities of the node to which it is connected Bandwidth The difference between the highest and lowest frequencies available for network signals Also synonymous with wire speed the actual speed of the data transmission along the cable Collision A condition in which packets transmitted over the cable interfere with each other Their interference makes both signals unintelligible Collision Domain Single CSMA CD LAN segment CSMA CD CSMA CD Carrier Sense Multiple Access Collision Detect is the communication method employed by Ethernet Fast Ethernet or Gigabit Ethernet End Station A workstation server or other device that does not forward traffic Glossary 1 Glossary Ethernet A network communication system developed and standardized by DEC Intel and Xerox using baseband transmission CSMA CD access logical bus topology and coaxial cable The successor IEEE 802 3 standard provides for integration into the OSI model and extends the physical layer and media with repeaters and implementations that operate on fiber thin coax and twisted pair cable Fast Ethernet A 100 Mbps network communication system based on Ethernet and the CSMA CD access method Gigabit Ethernet
7. Yellow 2 0 60 2 Wo g t 1 13 15 Console 500000 O rox Dig o oo ol O 8 2 u 16 24 Act o ooo O FDX FDX Green HDX 0FF Redundant Power Indicator Figure 1 3 System LEDs Table 1 2 System Status LEDs System Status LEDs LED Condition Status Power On Green Switch is receiving power Off Power off or failure Diag Flashing Green System self diagnostic test in progress On Green System self diagnostic test successfully completed On Red System self diagnostic test has failed BPS On Green The Backup Power Supply is receiving power Off The Backup P ower Supply is off 1 4 Features and Benefits 1 Optional Backup Power Supply The switch supports an optional Backup Power Supply BPS that can supply power to the switch in the event of failure of the internal power supply Power Supply Receptacles There are two power receptacles on the rear panel of the switch The standard power receptacle is for the AC power cord The receptacle labeled BPS is for the optional Backup Power Supply r X Ya A TS a Mar DEN aA waza z W m Figure 1 4 Power Supply Receptacle Features and Benefits Connectivity 24 dual speed ports for easy Gigabit Ethernet integration and for protection of your investment in legacy LAN equipment Auto negotiation enables each RJ 45 port to automatically select the optimum com
8. empowers multimedia applications with multicast switching and CoS services 10 100 1000 Mbps RJ 45 Ports SFP Slots System Indicators UJUUTUTUUTUTVUUDVUUVUTUUTVVUV JUTVUUTUWIVUVUVTUUTUUTUUUVy CE a D di d d a NERIN REN PR Redundant Power socket Port Status Indicators Power Socket Console Port 2 y ZA DAK N 2 NER Mr den x een Emm WEN WEN WEN Figure 1 1 Front and Rear Panels Switch Architecture The Gigabit Ethernet Switch employs a wire speed non blocking switching fabric This permits simultaneous wire speed transport of multiple packets at low latency on all ports This switch also features full duplex capability on all ports which effectively doubles the bandwidth of each connection The switch uses store and forward switching to ensure maximum data integrity With store and forward switching the entire packet must be received into a buffer and checked for validity before being forwarded This prevents errors from being propagated throughout the network Network Management Options This switch contains a comprehensive array of LEDs for at a glance monitoring of network and port status It also includes a management agent that allows you to configure or monitor the switch using its embedded management software or via SNMP applications To manage the switch you can make a direct c
9. mounting 3 3 rear panel receptacles 1 5 RJ 45 port 1 2 connections 4 1 pinouts B 2 rubber foot pads attaching 3 4 S safety compliance 1 vi screws for rack mounting 3 2 site selelction 3 1 SNMP agent 1 1 Spanning Tree Protocol 2 5 specifications compliances C 2 environmental C 1 physical C 1 power C 1 standards compliance 1 v standards compliance C 2 status LEDs 1 3 surge suppressor using 3 1 switch architecture 1 1 T tags VLAN 2 5 Telnet A 2 temperature within a rack 3 3 troubleshooting in band access A 1 power and cooling problems A 1 twisted pair connections 4 1 V VCCI compliance 1 vi VLANs 2 5 tagging 2 5 W Web based management 1 2 060190 10
10. stations in the same collision domain RJ 45 Connector A connector for twisted pair wiring Switched Ports Ports that are on separate collision domains or LAN segments TIA Telecommunications Industry Association Transmission Control Protocol Internet Protocol TCP IP Protocol suite that includes TCP as the primary transport protocol and IP as the network layer protocol UTP Unshielded twisted pair cable Virtual LAN VLAN A Virtual LAN is a collection of network nodes that share the same collision domain regardless of their physical location or connection point in the network A VLAN serves as a logical workgroup with no physical barriers allowing users to share information and resources as though located on the same LAN Glossary 3 Glossary Glossary 4 Index Numerics 10 Mbps connectivity rules 4 5 100 Mbps connectivity rules 4 4 4 5 1000 Mbps connectivity rules 4 4 1000BASE T pin Assignments B 2 1000BASE T ports 1 2 100BASE TX ports 1 2 10BASE T ports 1 2 10BASE T 100BASE TX pin Assignments B 1 A adhesive feet attaching 3 4 air flow requirements 3 1 application example 2 2 B backup power supply 1 5 BPS optional backup power supply 1 5 brackets attaching 3 3 buffer size C 1 Cc cable Ethernet cable compatibility 3 1 labeling and connection records 4 6 CE Mark 1 v cleaning fiber terminators 4 3 compliances 1 v EMC C 2 connectivity rules 10 Mbps 4 5 100 Mbps 4 4 4 5 1000 Mbps 4
11. switch ports For ease of understanding use a location based key when assigning prefixes to your cable labeling Use sequential numbers for cables that originate from the same equipment Differentiate between racks by naming accordingly Label each separate piece of equipment Display a copy of your equipment map including keys to all abbreviations at each equipment rack 4 6 Appendix A Troubleshooting Diagnosing Switch Indicators Table A 1 Troubleshooting Chart Troubleshooting Chart Symptom Action Power LED is Off Check connections between the switch the power cord and the wall outlet Contact your dealer for assistance Link LED is Off e Verify that the switch and attached device are powered on Be sure the cable is plugged into both the switch and corresponding device e Verify that the proper cable type is used and its length does notexceed specified limits Check the adapter on the attached device and cable connections for possible defects Replace the defective adapter or cable if necessary Diag LED is Red Try power cycling the switch to clear the condition Ifthe condition does not clear contact your dealer for assistance Power and Cooling Problems If the power indicator does not turn on when the power cord is plugged in you may have a problem with the power outlet power cord or internal power supply However if the unit powers off after runni
12. the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable When using any RJ 45 port on this switch you can use either straight through or crossover cable B 1 B Cables Table B 1 10 100BASE TX MDI and MDI X Port Pinouts Pin MDI X Signal Name MDI Signal Name 1 Receive Data plus RD Transmit Data plus TD 2 Receive Data minus RD Transmit Data minus TD 3 Transmit Data plus TD Receive Data plus RD 6 Transmit Data minus TD Receive Data minus RD 4 5 7 8 Notused Not used Note The and signs represent the polarity of the wires that make up each wire pair 1000BASE T Pin Assignments All 1000BASE T ports support automatic MDI MDI X operation so you can use straight through cables for all network connections to PCs or servers or to other switches or hubs The table below shows the 1000BASE T MDI and MDI X port pinouts These ports require that all four pairs of wires be connected Note that for 1000BASE T operation all four pairs of wires are used for both transmit and receive Use 100 ohm Category 5 5e or 6 unshielded twisted pair UTP or shielded twisted pair STP cable for 1000BASE T connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet Table B 2 1000BASE T MDI and MDI X Port Pinouts 1000BASE T MDI and MDI X Port Pinouts Pin MDI S
13. the manuals for these products However note that because switches break up the path for connected devices into separate collision domains you should not include the switch or connected cabling in your calculations for cascade length involving other devices 1000BASE T Cable Requirements All Category 5 UTP cables that are used for 100BASE TX connections should also work for 1000BASE T providing that all four wire pairs are connected However it is recommended that for all critical connections or any new cable installations Category 5e enhanced Category 5 or Category 6 cable should be used The Category 5e specification includes test parameters that are only recommendations for Category 5 Therefore the first step in preparing existing Category 5 cabling for running 1000BASE T is a simple test of the cable installation to be sure that it complies with the IEEE 802 3ab standards 1000 Mbps Gigabit Ethernet Collision Domain Table 4 1 Maximum 1000BASE T Gigabit Ethernet Cable Length Cable Type Maximum Cable Length Connector Category 5 5e 6 100 ohm UTP or STP 100 m 328 ft RJ 45 Table 4 2 Maximum 1000BASE SX Gigabit Ethernet Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 62 5 125 micron 160 MHz km 2 220 m 7 722 ft LC multimode fiber 200 MHz km 2 275 m 7 902 TU LC 50 125 micron multimode 400 MHz km 2 500 m 7 1641 ft LC fiber 500 MHz km 2 550 m 7 1805 ff LC
14. werden Wenn folgende Situationen auftreten ist das Ger t vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu berpr fen a Netzkabel oder Netzstecker sind besch digt b Fl ssigkeit ist in das Ger t eingedrungen c Das Ger t war Feuchtigkeit ausgesetzt d Wenn das Ger t nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen e Das Ger t ist gefallen und oder das Geh use ist besch digt f Wenn das Ger t deutliche Anzeichen eines Defektes aufweist Zum Netzanschlu dieses Ger tes ist eine gepr fte Leitung zu verwenden F r einen Nennstrom bis 6A und einem Ger tegewicht gr er 3kg ist eine Leitung nicht leichter als HO5VV F 3G 0 75mm2 einzusetzen Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weniger viii Warnings and Cautionary Messages Warning This product does not contain any servicable user parts Warning When connecting this device to a power outlet connect the field ground lead on the tri pole power plug to a valid earth ground line to prevent electrical hazards Warning This switch uses lasers to transmit signals over fiber optic cable The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation However you should never look directly at a transmit port when it is powered on Caution Wear an anti static
15. 100BASE TX connections and Category 3 4 or 5 for 10BASE T connections Cabling Guidelines The RJ 45 ports on the switch support automatic MDI MDI X pinout configuration so you can use standard straight through twisted pair cables to connect to any other network device PCs servers switches routers or hubs See Appendix B for further information on cabling Caution Do not plug a phone jack connector into an RJ 45 port This will damage the switch Use only twisted pair cables with RJ 45 connectors that conform to FCC standards Connecting to PCs Servers Hubs and Switches 1 Attach one end of a twisted pair cable segment to the device s RJ 45 connector Figure 4 1 Making Twisted Pair Connections 4 1 4 Making Network Connections 2 Ifthe device is a PC card and the switch is in the wiring closet attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet See Wiring Closet Connections on the next page Otherwise attach the other end to an available port on the switch 3 Make sure each twisted pair cable does not exceed 100 meters 328 ft in length Note Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem Otherwise back pressure jamming signals may degrade overall performance for the segment attached to the hub 4 As each connection is made the green Link LE
16. D on the switch corresponding to each port will light to indicate that the connection is valid Network Wiring Connections Today the punch down block is an integral part of many of the newer equipment racks It is actually part of the patch panel Instructions for making connections in the wiring closet with this type of equipment follows 1 Attach one end of a patch cable to an available port on the switch and the other end to the patch panel 2 If not already in place attach one end of a cable segment to the back of the patch panel where the punch down block is located and the other end to a modular wall outlet 3 Label the cables to simplify future troubleshooting Equipment Rac side view Network Switch Punch Down Block V Patch Panel Wall Figure 4 2 Network Wiring Connections 4 2 Fiber Optic SFP Devices 4 Fiber Optic SFP Devices An optional Gigabit SFP transceiver 1000BASE SX or 1000BASE LX can be used for a backbone connection between switches or for connecting to a high speed server Each multimode fiber optic port requires 50 125 or 62 5 125 micron multimode fiber optic cabling with an LC connector at both ends Each single mode fiber port requires 9 125 micron single mode fiber optic cable with an LC connector at both ends Caution This switch uses lasers to transmit signals over fiber optic cable The lasers are compliant with the req
17. Figure 1 2 Figure 1 3 Figure 1 4 Figure 2 1 Figure 2 2 Figure 2 3 Figure 2 4 Figure 3 1 Figure 3 2 Figure 3 3 Figure 3 4 Figure 3 5 Figure 3 6 Figure 3 7 Figure 4 1 Figure 4 2 Figure 4 3 Figure B 1 Front and Rear Panels Port LEDs System LEDs Power Supply Receptacle Collapsed Backbone Network Aggregation Plan Remote Connection with Fiber Cable Making VLAN Connections RJ 45 Connections Attaching the Brackets Installing the Switch in a Rack Attaching the Adhesive Feet Inserting an SFP Transceiver into a Slot Power Receptacle Serial Port DB 9 DTE Pin Out Making Twisted Pair Connections Network Wiring Connections Making SC Port Connections RJ 45 Connector Pin Numbers 3 4 3 6 4 1 4 2 4 3 B 1 xiii Figures xiv Chapter 1 Introduction Overview The Gigabit Ethernet Switch is an intelligent multilayer switch Layer 2 and 4 with 24 10 100 1000BASE T ports four of which are combination ports that are shared with four SFP transceiver slots There is also an SNMP based management agent embedded on the main board This agent supports both in band and out of band access for managing the switch This switch provides a broad range of powerful features for Layer 2 switching delivering reliability and consistent performance for your network traffic It brings order to poorly performing networks by segregating them into separate broadcast domains with IEEE 802 1Q compliant VLANs and
18. MHz with 1 kHz AM 80 Modulation 3 V m Power frequency magnetic field immunity test according to EN 61000 4 8 1993 1 A m at frequency 50 Hz e Voltage dips short interruptions and voltage variations immunity test according to EN 61000 4 11 1994 gt 95 Reduction 10 ms 30 Reduction 500 ms gt 95 Reduction 5000 ms LVD EN 60950 A1 1992 A2 1993 A3 1993 A4 1995 A11 1997 MDD e TEC 60601 1 Industry Canada Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Department of Communications Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe B prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par le minist re des Communications Japan VCCI Class B TOREJ HANEHBESERBSBENE ES VCCI DEE HOC FTSABERRWRECT CORBIS FSERETERTFALIE LAVE UC D N IOEENFTO FPTLEISTRERIHELT Rin RAEE AAA DUES AMY RL HAAS IIH TE LURYRUAEL CT Z D Safety Compliance Warning Fiber Optic Port Safety When using a fiber optic port never look at the transmit laser while it is CLASS powered on Also never look directly at the fiber TX port and fiber cable LASER DEVICE ends when they are powered on Avertissment Ports pour fibres optiques s cur
19. Part No 060190 10 Rev A December 2003 OmniStack 6300 24 Getting Started Guide y ALCATEL An Alcatel service agreement brings your company the assurance of 7x24 no excuses technical support You ll also receive regular software updates to maintain and maximize your Alcatel product s features and functionality and on site hardware replacement through our global network of highly qualified service delivery partners Additionally with 24 hour a day access to Alcatel s Service and Support web page you ll be able to view and update any case open or closed that you have reported to Alcatel s technical support open a new case or access helpful release notes technical bulletins and manuals For more information on Alcatel s Service Programs see our web page at www ind alcatel com call us at 1 800 995 2696 or email us at support ind alcatel com This Manual documents OmniStack 6300 24 hardware and software The functionality described in this Manual is subject to change without notice Copyright 2003 by Alcatel Internetworking Inc All rights reserved This document may not be reproduced in whole or in part without the express written permission of Alcatel Internetworking Inc Alcatel and the Alcatel logo are registered trademarks of Compagnie Financi re Alcatel Paris France OmniSwitch and OmniStack are registered trademarks of Alcatel Internetworking Inc Omni Switch Router SwitchExpert the Xylan logo are tr
20. Q EEE ee Server Farm mi E en A Hr mi TA KI JE de WE de WE E N d oe SoS a SS EiE be O JE E de oS ae Figure 2 2 Network Aggregation Plan 2 3 2 Network Planning Remote Connection with Fiber Cable Fiber optic technology allows for longer cabling than any other media type A 1000BASE SX MMF link can connect to a site up to 550 meters away and a 1000BASE LX SMF link can run up to 5 km This allows the Gigabit Ethernet Switch to serve as a collapsed backbone providing direct connectivity for a widespread LAN A 1000BASE SX SFP can be used for a high speed connection between floors in the same building and a 1000BASE LX SFP can be used to connect to other buildings in a campus setting The figure below illustrates this switch connecting multiple segments with fiber cable Headquarters _ N _ ITT NI epy eee ere 1000BASE SX MMF 1000BASE LX SMF 500 meters 5 kilometers Server Farm Remote Switch Remote Switch 10 100 1000 Mbps Segments _ 7 m N m EN il EDI l eae al J D y Sa St a A E Ag EE Fi
21. The switch has therefore been recognized as one of the most important building blocks for today s networking technology When performance bottlenecks are caused by congestion at the network access point such as the network card for a high volume file server the device experiencing congestion server power user or hub can be attached directly to a switched port And by using full duplex mode the bandwidth of the dedicated segment can be doubled to maximize throughput When networks are based on repeater hub technology the maximum distance between end stations is limited For Ethernet there may be up to four hubs between any pair of stations for Fast Ethernet the maximum is two This is known as the hop count However a switch turns the hop count back to zero So subdividing the network into smaller and more manageable segments and linking them to the larger network by means of a switch removes this limitation A switch can be easily configured in any Ethernet or Fast Ethernet network to significantly boost bandwidth while using conventional cabling and network cards 2 1 2 Network Planning Application Examples This Gigabit Ethernet Switch is not only designed to segment your network but also to provide a wide range of options in setting up network connections and linking VLANs Some typical applications are described below Collapsed Backbone The Gigabit Ethernet Switch is an excellent choice for mixed Ethernet Fast
22. ademarks of Alcatel Internetworking Inc All other brand and product names are trademarks of their respective companies y ALCATEL 26801 West Agoura Road Calabasas CA 91301 818 880 3500 FAX 818 880 3505 info ind alcatel com US Customer Support 800 995 2696 International Customer Support 818 878 4507 Internet http eservice ind alcatel com Warning This equipment has been tested and found to comply with the limits for Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions in this guide may cause interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void the user s authority to operate this equipment It is suggested that the user use only shielded and grounded cables to ensure compliance with FCC Rules This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the Canadian de
23. and cabling requirements to select an appropriate SFP transceiver type 2 Insert the transceiver with the optical connector facing outward and the slot connector facing down Note that SFP transceivers are keyed so they can only be installed in one orientation 3 Slide the SFP transceiver into the slot until it clicks into place Note SFP transceivers are hot swappable The switch does not need to be powered off before installing or removing a transceiver However always first disconnect the network cable before removing a transceiver Connecting to a Power Source To connect a device to a power source 1 Insert the power cable plug directly into the receptacle located at the back of the device 3 5 3 Installing the Switch 100 240V 50 60HZ 2A Figure 3 6 Power Receptacle 2 Plug the other end of the cable into a grounded 3 pin socket Note For International use you may need to change the AC line cord You must use a line cord set that has been approved for the receptacle type in your country 3 Check the front panel LEDs as the device is powered on to be sure the Power LED is lit If not check that the power cable is correctly plugged in 4 If you have purchased a Backup Power Supply connect it to the switch and to an AC power source now following the instructions included with the package Connecting to the Console Port The DB 9 serial port on the switch s front panel is used to con
24. eck the contents to be sure you have received all the components Then before beginning the installation be sure you have all other necessary installation equipment Package Contents e Gigabit Ethernet Switch Four adhesive foot pads Bracket Mounting Kit containing two brackets and eight screws for attaching the brackets to the switch Power Cord either US Continental Europe or UK e RS 232 console cable This Getting Started Guide User Guide Optional Rack Mounting Equipment If you plan to rack mount the switch be sure to have the following equipment available Four mounting screws for each device you plan to install in a rack these are not included A screwdriver Phillips or flathead depending on the type of screws used 3 2 Mounting 3 Mounting A switch unit can be mounted in a standard 19 inch equipment rack or on a desktop or shelf Mounting instructions for each type of site follow Rack Mounting Before rack mounting the switch pay particular attention to the following factors Temperature Since the temperature within a rack assembly may be higher than the ambient room temperature check that the rack environment temperature is within the specified operating temperature range See page C 1 Mechanical Loading Do not place any equipment on top of a rack mounted unit Circuit Overloading Be sure that the supply circuit to the rack assembly is not overloaded Grounding Rack m
25. ed and cannot be used The switch can also be configured to force the use of an RJ 45 port or SFP slot as required 1 2 Status LEDs Description of Hardware 1 The LEDs which are located on the front panel for easy viewing are shown below and described in the following table 00000000000 olWo Bs OO 2 4 6 8 0 2 4 6 8 2 22 AA 1000 Ooooooooooooomn FOX Green HDX 0FF L Link Act 1000 Green 10 100 Yellow x 000000 0 OUNO poe en ci Q OmniStack 6300 24 5 17 19 21 23 Console O O O OFX O Dig SFP LEDs FD Figure 1 2 Port LEDs Table 1 1 Port Status LEDs Port Status LEDs LED Condition Status RJ 45 Ports Link Act On Green Communications have been set to 1000 Mbps On Yellow Communications have been set to 10 100 Mbps Flashing Green Traffic is passing through the port at 1000 Mbps Flashing Yellow Traffic is passing through the port at 10 100 Mbps FDX Green Communications have been set to full duplex Off Communications have been set to half duplex SFP Transceiver Slots Ports 21 24 On Green An SFP transceiver port has established a valid 1000 Mbps network connection The associated RJ 45 port is disabled Off An SFP transceiver port has no valid link or the link has failed The associated RJ 45 portis enabled 1 3 1 Introduction Power Indicator Diagnostic Indicator Q OmniStack 6300 24 1000 Green 10 100
26. gure 2 3 Remote Connection with Fiber Cable 2 4 Application Examples 2 Making VLAN Connections VLANs can be based on port groups or each data frame can be explicitly tagged to identify the VLAN group to which it belongs When using port based VLANs ports can either be assigned to one specific group or to all groups Port based VLANs are suitable for small networks A single switch can be easily configured to support several VLAN groups for various organizational entities such as Finance and Marketing When you expand port based VLANs across several switches you need to make a separate connection for each VLAN group This approach is however inconsistent with the Spanning Tree Protocol which can easily segregate ports that belong to the same VLAN When VLANs cross separate switches you need to use VLAN tagging This allows you to assign multiple VLAN groups to the trunk ports that is tagged ports connecting different switches a ada s os LL J EE ho lO _ Y f Xx Untagged Ports Tagged Port VLAN aware VLAN ace m Finance unaware switch VLAN 2 Se switch Nan xx n nnn Testing Di N j En _ Marketing Di _ inance N EP GE eb rng VLAN 3 EE MP ES VLAN 4 J A EiE 1 a AS gt Soe VLAN 2 CUE y VLAN 3 _ Figure 2 4 Ma
27. h 100 m 328 ft Buffer Architecture 2 Mbytes Aggregate Bandwidth 48 Gbps Switching Database 16K MAC address entries LEDs System Power Power Supply Diag Diagnostics BPS Backup Power Supply Port Link Act Activity FDX Duplex half duplex Weight 4 3 kg 9 46 Ibs Size 44 0 x 41 0 x 4 4 cm 17 4 x 17 3 x 1 7 in Temperature Operating 0 to 40 C 32 to 122 F Storage 40 to 70 C 40 to 158 F Humidity Operating 5 to 95 non condensing AC Input 100 to 240 V 50 60 Hz Power Supply Internal auto ranging transformer 90 to 240 VAC 47 to 63 Hz External supports connection for backup power supply C 1 C Specifications Power Consumption 70 Watts maximum Maximum Current 1 2 A 110 VAC 0 6 A 240 VAC Compliances CE Mark Emissions FCC Class B Industry Canada Class B EN55022 CISPR 22 Class B EN 61000 3 2 3 VCCI Class B C Tick AS NZS 3548 1995 Class B Immunity EN 61000 4 2 3 4 5 6 8 11 Safety CSA NRTL CSA 22 2 950 amp UL 1950 EN60950 TUV GS C 2 Glossary 10BASE T IEEE 802 3 specification for 10 Mbps Ethernet over two pairs of Category 3 4 or 5 UTP cable 1000BASE LX IEEE 802 3z specification for Gigabit Ethernet over two strands of 50 125 62 5 125 or 9 125 micron core fiber cable 1000BASE SX IEEE 802 3z specification for Gigabit Ethernet over two strands of 50 125 or 62 5 125 micron core fiber cable 1000BASE T IEEE 802 3ab specification for
28. ignal Name MDI X Signal Name 1 Bi directional Data One Plus BI_D1 Bi directional Data Two Plus BI_D2 2 Bi directional Data One Minus BI_D1 Bi directional Data Two Minus BI_D2 3 Bi directional Data Two Plus BI_D2 Bi directional Data One Plus BI_D1 4 Bi directional Data Three Plus BI_D3 Bi directional Data Four Plus BI_D4 5 Bi directional Data Three Minus BI_D3 Bi directional Data Four Minus BI_D4 6 Bi directional Data Two Minus BI_D2 Bi directional Data One Minus BI_D1 7 Bi directional Data One Plus BI_D4 Bi directional Data One Plus BI_D3 8 Bi directional Data Four Minus BI_D4 Bi directional Data Three Minus BI_D3 Cable Testing for Existing Category 5 Cable Installed Category 5 cabling must pass tests for Attenuation Near End Crosstalk NEXT and Far End Crosstalk FEXT This cable testing information is specified in the ANSI TIA EIA TSB 67 standard Additionally cables must also pass test parameters for Return Loss and Equal Level Far End Crosstalk ELFEXT These B 2 Fiber Standards B tests are specified in the ANSI TIA ElA TSB 95 Bulletin The Additional Transmission Performance Guidelines for 100 Ohm 4 Pair Category 5 Cabling Note that when testing your cable installation be sure to include all patch cables between switches and end devices Adjusting Existing Category 5 Cabling to Run 1000BASE T If your existing Category 5 ins
29. it sur le plan optique Ne regardez jamais le laser tant qu il est sous tension Ne regardez we jamais directement le port TX Transmission a fibres optiques et les embouts de cables a fibres optiques tant qu ils sont sous tension Warnhinweis Faseroptikanschl sse Optische Sicherheit Niemals ein Ubertragungslaser betrachten wahrend dieses LASERGERAT eingeschaltet ist Niemals direkt auf den Faser TX Anschlu DER KLASSE A j und auf die Faserkabelenden schauen w hrend diese eingeschaltet sind Underwriters Laboratories Compliance Statement Important Before making connections make sure you have the correct cord set Check it read the label on the cable against the following Operating Voltage Electrical Cord Requirements Operating Voltage Cord Set Specifications 120 Volts UL Listed CSA Certified Cord Set Minimum 18 AWG Type SVT or SUT three conductor cord Maximum length of 15 feet Parallel blade grounding type attachment plug rated 15A 125V 240 Volts Europe only Cord Set with HOSVV F cord having three conductors with minimum diameter of 0 75 mm2 IEC 320 receptacle Male plug rated 10A 250V The unit automatically matches the connected input voltage Therefore no additional adjustments are necessary when connecting it to any input voltage within the range marked on the rear panel vii Wichtige Sicherheitshinweise Germany 10 11 12 13
30. king VLAN Connections Note When connecting to a switch that does not support IEEE 802 1Q VLAN tags use untagged ports 2 5 2 Network Planning Application Notes 1 2 6 Full duplex operation only applies to point to point access such as when a switch is attached to a workstation server or another switch When the switch is connected to a hub both devices must operate in half duplex mode Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem Otherwise back pressure jamming signals may degrade overall performance for the segment attached to the hub As a general rule the length of fiber optic cable for a single switched link should not exceed 550 m 1805 ft for multimode fiber or 5 km 16404 ft for single mode fiber However power budget constraints must also be considered when calculating the maximum cable length for your specific environment Chapter 3 Installing the Switch Selecting a Site Switches can be mounted in a standard 19 inch equipment rack or on a flat surface Be sure to follow the guidelines below when choosing a location The site should be at the center of all the devices you want to link and near a power outlet be able to maintain its temperature within 0 to 50 C 32 to 122 F and its humidity within 5 to 95 non condensing provide adequate space approximately two inches on all sides for proper air flow be accessible f
31. munication mode half or full duplex if this feature is supported by the attached device otherwise the port can be configured manually Independent RJ 45 10 100 1000BASE T ports with auto MDI MDI X pinout selection e Unshielded UTP cable supported on all RJ 45 ports Category 3 4 or 5 for 10 Mbps connections Category 5 or 5e for 100 Mbps connections and Category 5 or better for 1000 Mbps connections IEEE 802 3 Ethernet 802 3u Fast Ethernet 802 3z and 802 3ab Gigabit Ethernet compliance ensures compatibility with standards based hubs network cards and switches from any vendor Expandability Supports 1000BASE SX and 1000BASE LX SFP transceivers Performance Transparent bridging e Switching table with a total of 16K MAC address entries Provides store and forward switching Supports wire speed switching Supports flow control using back pressure for half duplex and IEEE 802 3x for full duplex Broadcast storm control Desktop or rack mountable 1 5 1 Introduction Management At a glance LEDs for easy troubleshooting Network management agent e Manages switch in band or out of band Supports Telnet SNMP RMON and Web based interface 1 6 Chapter 2 Network Planning Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non crossbar switching This means that it can partition a network more efficiently than bridges or routers
32. nect to the switch for out of band console configuration The on board configuration program can be accessed from a terminal or a PC running a terminal emulation program The pin assignments used to connect to the serial port are provided in the following tables 6 9 Figure 3 7 Serial Port DB 9 DTE Pin Out 3 6 Connecting to the Console Port 3 Wiring Map for Serial Cable Table 3 1 Serial Cable Wiring Switch s 9 Pin Null Modem PC s 9 Pin Serial Port DTE Port 2 RXD receive data CE 3 TXD transmit data 3 TXD transmit data gt 2 RXD receive data 5 SGND signal ground 5 SGND signal ground No other pins are used The serial port s configuration requirements are as follows Default Baud rate 9 600 bps Character Size 8 Characters Parity None Stop bit One Data bits 8 3 7 3 Installing the Switch 3 8 Chapter 4 Making Network Connections Connecting Network Devices This switch is designed to interconnect multiple segments or collision domains It can be connected to network cards in PCs and servers as well as to hubs switches or routers It may also be connected to devices using optional SFP transceivers Twisted Pair Devices Each device requires an unshielded twisted pair UTP cable with RJ 45 connectors at both ends Use Category 5 5e or 6 cable for 1000BASE T connections Category 5 for
33. ng for a while check for loose power connections power losses or surges at the power outlet and verify that the fans on the unit are unobstructed and running prior to shutdown If you still cannot isolate the problem then the internal power supply may be defective Installation Verify that all system components have been properly installed If one or more components appear to be malfunctioning such as the power cord or network cabling test them in an alternate environment where you are sure that all the other components are functioning properly In Band Access You can access the management agent in the switch from anywhere within the attached network using Telnet a Web browser or other network management software tools However you must first configure the switch with a valid IP address A 1 A Troubleshooting subnet mask and default gateway If you have trouble establishing a link to the management agent check to see if you have a valid network connection Then verify that you entered the correct IP address Also be sure the port through which you are connecting to the switch has not been disabled If it has not been disabled then check the network cabling that runs between your remote location and the switch Caution The management agent can accept up to four simultaneous Telnet sessions If the maximum number of sessions already exists an additional Telnet connection will not be able to log into the system A 2 Ap
34. ns 4 1 Connecting Network Devices 4 1 xi Contents Twisted Pair Devices 4 1 Cabling Guidelines 4 1 Connecting to PCs Servers Hubs and Switches 4 1 Network Wiring Connections 4 2 Fiber Optic SFP Devices 4 3 Connectivity Rules 4 4 1000BASE T Cable Requirements 4 4 1000 Mbps Gigabit Ethernet Collision Domain 4 4 100 Mbps Fast Ethernet Collision Domain 4 5 10 Mbps Ethernet Collision Domain 4 5 Cable Labeling and Connection Records 4 6 Appendix A Troubleshooting A 1 Diagnosing Switch Indicators A 1 Power and Cooling Problems A 1 Installation A 1 In Band Access A 1 Appendix B Cables B 1 Twisted Pair Cable and Pin Assignments B 1 10BASE T 100BASE TX Pin Assignments B 1 1000BASE T Pin Assignments B 2 Fiber Standards B 3 Appendix C Specifications C 1 Compliances C 2 Glossary Index xii Tables Table 1 1 Table 1 2 Table 3 1 Table 4 1 Table 4 2 Table 4 3 Table 4 4 Table 4 5 Table A 1 Table B 1 Table B 2 Port Status LEDs System Status LEDs Serial Cable Wiring Maximum 1000BASE T Gigabit Ethernet Cable Length Maximum 1000BASE SX Gigabit Ethernet Cable Lengths Maximum 1000BASE LX Gigabit Ethernet Cable Length Maximum Fast Ethernet Cable Lengths Maximum Ethernet Cable Length Troubleshooting Chart 10 100BASE TX MDI and MDI X Port Pinouts 1000BASE T MDI and MDI X Port Pinouts 1 3 1 4 3 7 4 4 4 4 4 5 4 5 A 1 B 2 B 2 xi Tables xii Figures Figure 1 1
35. onnection to the RS 232 console port out of band or you can manage the switch through a network 1 1 1 Introduction connection in band using Telnet the on board Web agent or Windows based network management software For a detailed description of the switch s advanced features refer to the User Guide Description of Hardware 10 100 1000BASE T Ports These ports are RJ 45 ports that operate at 10 Mbps or 100 Mbps half or full duplex or at 1000 Mbps full duplex Because all ports on this switch support automatic MDI MDI X operation you can use straight through cables for all network connections to PCs or servers or to other switches or hubs See 1000BASE T Pin Assignments on page B 2 Each of these ports support auto negotiation so the optimum transmission mode half or full duplex and data rate 10 100 or 1000 Mbps can be selected automatically If a device connected to one of these ports does not support auto negotiation the communication mode of that port can be configured manually Each port also supports auto negotiation of flow control so the switch can automatically prevent port buffers from becoming saturated SFP Slots The Small Form Factor Pluggable SFP transceiver slots are shared with four of the RJ 45 ports Ports 21 24 In its default configuration if an SFP transceiver purchased separately is installed in a slot and has a valid link on its port the associated RJ 45 port is disabl
36. or installing cabling and maintaining the devices allow the status LEDs to be clearly visible Make sure twisted pair cable is always routed away from power lines fluorescent lighting fixtures and other sources of electrical interference such as radios and transmitters Make sure that the unit is connected to a separate grounded power outlet that provides 100 to 240 VAC 50 to 60 Hz is within 2 44 m 8 feet of each device and is powered from an independent circuit breaker As with any equipment using a filter or surge suppressor is recommended Ethernet Cabling To ensure proper operation when installing the switch into a network make sure that the current cables are suitable for 10BASE T 100BASE TX or 1000BASE T operation Check the following criteria against the current installation of your network e Cable type Unshielded twisted pair UTP or shielded twisted pair STP cables with RJ 45 connectors Category 3 or better for 10BASE T Category 5 or better for 100BASE TX and Category 5e or better for 1000BASE T Protection from radio frequency interference emissions Electrical surge suppression Separation of electrical wires switch related or other and electromagnetic fields from data based network wiring Safe connections with no damaged cables connectors or shields 3 1 3 Installing the Switch RJ 45 Connector Figure 3 1 RJ 45 Connections Equipment Checklist After unpacking the switch ch
37. ounted equipment should be properly grounded Particular attention should be given to supply connections other than direct connections to the mains To rack mount devices 1 Attach the brackets to the device using the screws provided in the Bracket Mounting Kit Figure 3 2 Attaching the Brackets 3 3 3 Installing the Switch 2 Mount the device in the rack using four rack mounting screws not provided Figure 3 3 Installing the Switch in a Rack 3 If installing a single switch only turn to Connecting to a Power Source at the end of this chapter 4 If installing multiple switches mount them in the rack one below the other in any order Desktop or Shelf Mounting 1 Attach the four adhesive feet to the bottom of the first switch ne Sr Saa Figure 3 4 Attaching the Adhesive Feet 2 Set the device on a flat surface near an AC power source making sure there are at least two inches of space on all sides for proper air flow 3 4 Connecting to a Power Source 3 3 If installing a single switch only go to Connecting to a Power Source at the end of this chapter 4 If installing multiple switches attach four adhesive feet to each one Place each device squarely on top of the one below in any order Installing an Optional SFP Transceiver into the Switch Figure 3 5 Inserting an SFP Transceiver into a Slot To install an SFP transceiver do the following 1 Consider network
38. partment of communications Le present appareil numerique niemet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la Class B prescrites dans le reglement sur le brouillage radioelectrique edicte par le ministere des communications du Canada Compliances and Safety Warnings FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with instructions may cause harmful interference to radio communications However there is no guarantee that the inter ference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help EC Conformance Declaration Class B SMC contact for these products in E
39. pendix B Cables Twisted Pair Cable and Pin Assignments Caution DO NOT plug a phone jack connector into any RJ 45 port Use only twisted pair cables with RJ 45 connectors that conform with FCC standards For 10BASE T 100BASE TX connections a twisted pair cable must have two pairs of wires Each wire pair is identified by two different colors For example one wire might be green and the other green with white stripes Also an RJ 45 connector must be attached to both ends of the cable Caution Each wire pair must be attached to the RJ 45 connectors in a specific orientation See Cabling Guidelines on page 4 1 for an explanation The figure below illustrates how the pins on the RJ 45 connector are numbered Be sure to hold the connectors in the same orientation when attaching the wires to the pins Figure B 1 RJ 45 Connector Pin Numbers 10BASE T 100BASE TX Pin Assignments Use unshielded twisted pair UTP or shielded twisted pair STP cable for RJ 45 connections 100 ohm Category 3 4 or 5 cable for 10 Mbps connections or 100 ohm Category 5 cable for 100 Mbps connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet The RJ 45 ports on the switch base unit support automatic MDI MDI X operation you can use straight through cables for all network connections to PCs or servers or to other switches or hubs In straight through cable pins 1 2 3 and 6 at one end of
40. tallation does not meet one of the test parameters for 1000BASE T there are basically three measures that can be applied to try and correct the problem 1 Replace any Category 5 patch cables with high performance Category 5e or Category 6 cables 2 Reduce the number of connectors used in the link 3 Reconnect some of the connectors in the link Fiber Standards The current TIA Telecommunications Industry Association 568 A specification on optical fiber cabling consists of one recognized cable type for horizontal subsytems and two cable types for backbone subsystems Horizontal 62 5 125 micron multimode two fibers per outlet Backbone 62 5 125 micron multimode or singlemode TIA 568 B will allow the use of 50 125 micron multimode optical fiber in both the horizontal and backbone in addition to the types listed above All optical fiber components and installation practices must meet applicable building and safety codes B 3 B Cables B 4 Appendix C Specifications Physical Characteristics Ports 24 10 100 1000BASE T with auto negotiation 4 SFP Small Form factor Pluggable 1000 Mbps only Network Interface Ports 1 24 RJ 45 connector auto MDI X 10BASE T RJ 45 100 ohm UTP cable Categories 3 4 5 Maximum Cable Length 100 m 328 ft 100BASE TX RJ 45 100 ohm UTP cable Category 5 Maximum Cable Length 100 m 328 ft 1000BASE T RJ 45 100 ohm UTP or STP cable Category 5 5e or 6 Maximum Cable Lengt
41. the hardware features of the OmniStack 6300 switch including Its physical and performance related characteristics and how to install the switch Related Publications The following publication gives specific information on how to operate and use the management functions of the switch The OmniStack 6300 User Guide Also as part of the switch s firmware there is an online web based help that describes all management related features Contents Chapter 1 Introduction 1 1 Overview 1 1 Switch Architecture 1 1 Network Management Options 1 1 Description of Hardware 1 2 10 100 1000BASE T Ports 1 2 SFP Slots 1 2 Status LEDs 1 3 Optional Backup Power Supply 1 5 Power Supply Receptacles 1 5 Features and Benefits 1 5 Connectivity 1 5 Expandability 1 5 Performance 1 5 Management 1 6 Chapter 2 Network Planning 2 1 Introduction to Switching 2 1 Application Examples 2 2 Collapsed Backbone 2 2 Network Aggregation Plan 2 3 Remote Connection with Fiber Cable 2 4 Making VLAN Connections 2 5 Application Notes 2 6 Chapter 3 Installing the Switch 3 1 Selecting a Site 3 1 Ethernet Cabling 3 1 Equipment Checklist 3 2 Package Contents 3 2 Optional Rack Mounting Equipment 3 2 Mounting 3 3 Rack Mounting 3 3 Desktop or Shelf Mounting 3 4 Installing an Optional SFP Transceiver into the Switch 3 5 Connecting to a Power Source 3 5 Connecting to the Console Port 3 6 Wiring Map for Serial Cable 3 7 Chapter 4 Making Network Connectio
42. uirements of a Class 1 Laser Product and are inherently eye safe in normal operation However you should never look directly at a transmit port when it is powered on 1 Remove and keep the LC port s rubber cover When not connected to a fiber cable the rubber cover should be replaced to protect the optics 2 Check that the fiber terminators are clean You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol Dirty fiber terminators on fiber cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port 3 Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device Since LC connectors are keyed the cable can be attached in only one orientation Al ea Figure 4 3 Making LC Port Connections 4 As a connection is made check the green Link LED on the switch corresponding to the port to be sure that the connection is valid The 1000BASE SX and 1000BASE LX fiber optic ports operate at 1 Gbps full duplex with auto negotiation of flow control The maximum length for fiber optic cable operating at Gigabit speed will depend on the fiber type as listed under 1000 Mbps Gigabit Ethernet Collision Domain on page 4 4 4 3 4 Making Network Connections Connectivity Rules When adding hubs repeaters to your network please follow the connectivity rules listed in
43. urope is SMC Networks Europe Edificio Conata I Calle Fructu s Gelabert 6 8 20 4a 08970 Sant Joan Despi Barcelona Spain This information technology equipment complies with the requirements of the Council Directive 89 336 EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73 23 EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93 68 EEC For the evaluation of the compliance with these Directives the following standards were applied RFI Emission Limit class B according to EN 55022 1998 IEC 60601 1 2 EMC medical Limit class A for harmonic current emission according to EN 61000 3 2 1995 e Limitation of voltage fluctuation and flicker in low voltage supply system according to EN 61000 3 3 1995 Immunity Product family standard according to EN 55024 1998 e Electrostatic Discharge according to EN 61000 4 2 1995 Contact Discharge 4 kV Air Discharge 8 kV Radio frequency electromagnetic field according to EN 61000 4 3 1996 80 1000 MHz with 1 kHz AM 80 Modulation 3 V m e Electrical fast transient burst according to EN 61000 4 4 1995 AC DC power supply 1 kV Data Signal lines 0 5 kV Surge immunity test according to EN 61000 4 5 1995 AC DC Line to Line 1 kV AC DC Line to Earth 2 kV vi e Immunity to conducted disturbances Induced by radio frequency fields EN 61000 4 6 1996 0 15 80
44. wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment Caution Do not plug a phone jack connector in the RJ 45 port This may damage this device Les raccordeurs ne sont pas utilis pour le systeme t l phonique Caution Use only twisted pair cables with RJ 45 connectors that conform to FCC standards Environmental Statement The manufacturer of this product endeavours to sustain an environmentally friendly policy throughout the entire production process This is achieved though the following means Adherence to national legislation and regulations on environmental production standards Conservation of operational resources Waste reduction and safe disposal of all harmful un recyclable by products Recycling of all reusable waste content Design of products to maximize recyclables at the end of the product s life span Continual monitoring of safety standards End of Product Life Span This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life Manufacturing Materials There are no hazardous nor ozone depleting materials in this product Documentation All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests The inks used in the printing process are non toxic Purpose This guide details
Download Pdf Manuals
Related Search