WaterLogic WL Cube Firewall Operating instructions
Contents
1. chill the water 20 Clean the outside of the machine with a non abrasive anti bacterial wipe or cloth 21 Taste the water one final time and check it is cooling and heating the water SANITISING You will need the following items e A Phillips screwdriver e Rubber gloves e Aqua Dosa sanitisation fluid e Suitable test strips to work with your sanitisation fluid e Non abrasive anti bacterial wipe or cloth e A container that can hold 5 litres 1 Put on the rubber gloves to minimise the chance of any contamination to the machine and to protect yourself whilst the sanitisation procedure is being carried out 2 You will need to stop the water supply to the machine by turning the isolation valve to the off position and releasing the pressure by selecting the cold water option until the water stops being dispensed 3 lsolate the power to the Cube by turning the red and green power switches off these are located at the rear of the machine Remove the power lead as a second safety precaution The Cube Technical Manual Version 1 May 2014 waterlogic 4 Remove the top cover from the Cube by undoing the two screws located at the back of the machine then slide the panel backwards and lift up 5 Take out the filter by un clicking the loop at the top of the housing and pulling it in an upward motion If there are two filters in the machine then both of these need to be removed 6 Unscrew the filter housing s and remove the2. JG LLD PE Tube Blue O D 1 4 JG Stem Elbow Connector 1 4 1 4 Solenoid Valve 24 DC Single Spring Load JG Equal Tee Connector 1 4 JG Equal Elbow Connector 1 4 JG Stem Elbow Connector 1 4 1 4 Hot amp Cold Solenoid Valve 24V 300mm CUBE JG LLD PE Tube Blue O D 1 4 JG Equal Elbow Connector 1 4 JG LLD PE Tube Blue O D 1 4 JG Equal Tee Connector 1 4 JG Equal Elbow Connector 1 4 JG LLD PE Tube Blue O D 1 4 Solenoid Valve 24 DC Single Spring Load JG Stem Elbow Connector 1 4 1 4 Drain valve cap only for 5 16 amp 1 4 size Drain valve body only for 5 16 JG LLDPE Tube Blue 8mm JG LLD PE Tube Blue O D 1 4 JG Equal Elbow Connector 1 4 1 3 litre 500W Hot Tank for Cube Cube cold tank 1 4 Litre Spiral Quartz Silicon Tube 5 16 for hot water JG Equal Elbow Connector 1 4 JG Stem Elbow Connector 1 4 1 4 JG LLD PE Tube Blue O D 1 4 The Cube Technical Manual Version 1 May 2014 33 Wetted Parts List Hot Cold and Sparkling Ne Part Description 30 Silicon Tube 5 16 for hot water 31 JG End Stop 1 4 2 JG LLD PE Tube Blue O D 1 4 33 JG Equal Tee Connector 1 4 34 JG 1 4 STOPPER JG UK 35 JG Equal Tee Connector 1 4 36 JG LLD PE Tube Blue O D 1 4 37 JG LLD PE Tube Blue O D 1 4 38 Solenoid Valve 24 DC Single Spring Load 39 JG Equal Tee Connector 1 4 40 JG Stem Elbow Connector 1 4 1 4 41 JG Equal Tee Connector 1 4 42 JG LLD PE T
3. an independent laboratory to show its ability to inhibit the growth of bacteria mould and fungi by up to 99 9 over a 24 hour period and for the duration of the machine life FREQUENTLY ASKED QUESTIONS ABOUT BIOCOTE Why use BioCote BioCote will help reduce the risk of cross contamination You may not want to think about it but every surface in the working environment is a potential breeding ground for Bacteria How is it applied BioCote is applied via an additive into the manufacturing process and will therefore be present throughout the molded or painted parts How long will BioCote last BioCote will last for the usual life expectancy of your water dispenser It will not wear or wash out with use or cleaning What bacteria is BioCote effective against BioCote is effective against most common bacteria moulds and fungi Please note BioCote is an additional line of defence to protect between cleaning routines it is not a replacement for your normal cleaning and sanitisation processes 26 waterlogic Rattar thinking Rattar water Better thinking Better water Electrical Wiring Diagram 120V UV WATER DISPENSER ELECTRICAL WIRING DIAGRAM Hot amp Cold amp Ambient POWER SOURCE WHITE G GREEN G Y GREEN amp YELLOW The Cube Technical Manual Version 1 May 2014 27 waterlogic Electrical Wiring Diagram 230V Dip Switch Setup THE CUBE MAIN PCB UV WATER DISPENSER ELEC
4. e Never try to fill more than one vessel at a time waterlogic Better thinking Better water Operating Instructions CS aa m a COLD WATER Select cold water and press dispensing button AMBIENT WATER Select ambient water and press dispensing button HOT WATER A Press and hold the hot water icon for 3 seconds until the icon has illuminated orange select the dispense button and hot water will be dispensed This safety feature prevents hot water from being dispensed accidentally especially by children EXTRA HOT WATER A Press and hold the extra hot water icon on the display panel the icon will flash red to indicate that the water is heating Once the icon turns off the water is at the correct temperature and extra hot water can be dispensed following the same method as Hot Water DISPENSING BUTTON Press and hold this icon after selecting the type of water you wish to be dispensed when your cup has reached the desired level release the button The Cube Technical Manual Version 1 May 2014 Maintenance and Servicing e The Cube must be serviced every 12 months but we strongly recommend the UV lamp and filters be changed every six months e The Cube may require any calcium build up in the hot tank to be removed this depends on the local water conditions e No paperwork or cleaning records should be stored inside the Cube e To reset the filter timer hold down the hot and cold icons simultaneous
5. filter cartridge place this to one side as this will need to be re fitted this once you have completed the sanitising procedure 7 Measure 40ml of Aqua Dosa sanitising fluid into one of the empty filter housings and securely fasten the filter head Re fit the filter s into the machine pushing it firmly into place 8 Replace the top cover and re connect the power lead then turn on the red switch at the rear of the machine Turn the water supply back on 9 Dispense cold water until the sanitisation fluid leaves the faucet this can be checked by dispensing cold water until the colour of the test strip has changed to indicate the presence of the sanitisation fluid Normally about 400 500mlI of water needs to be dispensed Do not let any sanitisation fluid enter the hot tank 10 Leave the sanitisation fluid inside the machine for a minimum of 10 15 minutes when this time has been reached flush water through the machine until there is no sanitisation fluid left inside You can use your test strips to check that all of the Sanitisation fluid has been effectively flushed out 11 Turn off the water supply to the machine and release the internal pressure by selecting the cold option until the water stops being dispensed Isolate the power to the machine by switching the red switch at the rear of the machine off and removing the power lead 12 Remove the top cover from the machine and take out the filter s and unscrew the filter housing po
6. liable for any damage which could affect directly or indirectly any person or property Please be aware that any warranties accompanying the sale of our products will be invalidated by any of the following e Incorrect installation e Incorrect use of the Cube e Unsuitable electrical and water supply e Major short coming of maintenance e Technical interventions or alterations of an unauthorised nature e Adoption and use of unapproved spare parts e Any repair by untrained personnel Waterlogic has a policy of constant and continual improvement and therefore reserves the right to change specifications without prior notice other than in the case of significant changes 24 Cube 120V HCA Cube 230V HCA Machine Size Machine Weight Power Supply Heater Fan Compressor UV Lamp Unit Total Refrigeration Gas R134a Cold Tank Capacity Hot Tank Capacity Water Connection Minimum Water Pressure Bar Megapascal Maximum Water Pressure Bar Megapascal Recommended Water Pressure Bar Megapascal Minimum Incoming Flow Rate litres per minute Dispensing Flow Rate Cold Water Temperature Range Hot Water Temperature Range 296mm W x 425mm D x 375mm H 18Kg 120 Volt 60Hz 500W 4 2A 2W 120W 1 7A 13W 0 3A 635W 6 2A 55g 1 940Z 1 4L ToL 1 4 Hose 3 77 0 377 6 0 0 6 4 35 0 435 1 0 Ipm 1 3lpm 5 C 15 C 41 F 59 F 80 C 95 C 176 F 203 F waterlogic Better
7. the icon will flash red to indicate that the water is heating Once the icon turns off the water is at the correct temperature and extra hot water can be dispensed following the same method as Hot Water DISPENSING BUTTON Press and hold this icon after selecting the type of water you wish to be dispensed when your cup has reached the desired level release the button QQuatertogic UV LAMP FILTER HAS FAILED SERVICE Replace UV DEMAND lamp Replace filter cartridge POWER UV OK 21 waterlogic COLD WATER Select cold water and press dispensing button AMBIENT WATER Select ambient water and press dispensing button A LEAK HAS BEEN DETECTED Turn off the water supply and call your authorized service agent The Cube Technical Manual Version 1 May 2014 FAULT FINDING All fault finding procedures must be carried out by a technician trained by Waterlogic International or their nominated distributor Please take great care and suitable health and safety measures when fault finding on live electrical parts 1 No flow of water Ensure that there is a water supply to the Cube from the building and that the installation isolation valve is turned on If the installation kit has an anti leak device included in it as Waterlogic Installation kit then make sure it has not tripped 2 No flow of water Check that the water filters are not blocked and that t
8. TRICAL WIRING DIAGRAM ToD Hot amp Cold amp Ambient POWER SOURCE AC230V BL BLUE BR BROWN BK BLACK W WHITE G GREEN G Y GREEN amp YELLOW Dip switch 2 Dip switch 1 The Cube Technical Manual Version 1 May 2014 28 29 waterlogic Better thinking Better water Dip Switch Setup When reading this document please note the white coloring on the diagrams indicate the required position of the switch to determine the setting DIP SWITCH 1 SETUP DIP SWITCH 2 SETUP DP1 DP2 UV SETTING FILTER TIMER SETTING COLD WATER HOT WATER SLEEP MODE e CS CDS Sensor A combination of dip switches 2 TEMPERATURE TEMPERATURE Hot water temp range Used in Europe amp 3 is used to enter this setup SETTING SETTING gt ON e US UV Sensor e 3month Cold water temp range Hot water temp range e OFF e Gmonth e 5 c e 80 C e 12month e 10 c e 87 C e No filter timer e 15 c e 95 C The Cube Technical Manual Version 1 May 2014 30 31 Wetted Parts List Hot Cold and Ambient 48 47 46 45 44 43 41 4039 38 37 36 35 34 33 32 31 3029 2827 I ah T ggi MLE a aT Lart 456 78 10 11 13 14 15 16 1718 19 21 2223 24 25 32 Ne Part Description O ON OoBRWN gt SS ee en eee ee ee ae 2 ae ee Ped Pay LS OES hay PEs PO OS Io oe Sion Gal Ss COdIS TS re waterlogic Better thinking Better water JG Bulkhead Connector Union 1 4 1 4 JG LLD PE Tube Blue O D 1 4
9. at will trigger an alarm or it will trip the Waterlogic block located on the installation kit Should you see water leaking from the Cube isolate the supply and Start normal fault finding procedures 9 No power Check the building electrical supply to the Cube is on and that the power cord is plugged in Ensure the red power switch at the rear of the Cube is on Test the Cube s fuse Check that the top cover isolation switch is being activated by the top cover being locked in place correctly If all these points are OK then start normal fault finding procedures 10 All Icons flashing and audible alarm An over heat fault has been detected please switch the Cube off immediately and start fault finding procedures waterlogic Better thinking Better water a F 2 h k E 3 a es a 2 y ies F i p as j F ie A r r F i 2 PY ae a ee T lt js 3 J p P wa Sh E ri gar a z f cag pn 22 a ER 4 a f ee F a a A GF pA Ah M RAE AA f if a k d ii i T ip TA ne eet f T i ge i ua y i e t i F kS at Hra 4 k i 9 u J Mci i 3 bi Y a 3 ira 4 7 A pna i a 7 e lt 7 3 F i a a EF ff 6 r a The Cube Technical Manual Version 1 May 2014 23 Technical Specifications and Warranties SAFETY Subject to the standard terms and conditions of sale a copy of which has been provided to you neither Waterlogic International Limited Waterlogic nor any affiliated companies shall be
10. bed and breakfast type environments catering and similar non retail applications 12 This appliance contains a UV C emitter UV lamp 13 Unintended use of the appliance or damage to the housing may result in the escape of dangerous UV C radiation UV C radiation may even in little doses cause harm to the eyes and skin 14 Appliances that are obviously damaged must not be used 15 The replacement of the UV lamp must be carried out by personnel trained by Waterlogic International or their approved distributors 16 Read the maintenance instructions before opening the appliance 17 The appliance must be disconnected from the power supply before replacing the UV lamp 18 The UV lamp must be replaced at 6 month intervals or when necessary If the unit is placed in a high use area the UV lamp will need to be replaced more frequently The quartz spiral can be cleaned by using an ultrasonic bath if needed 19 WARNING Do not operate the UV lamp when it is removed from the appliance enclosure The Cube Technical Manual Version 1 May 2014 waterlogic Better thinking Better water Machine Overview THE CUBE The Cube is available in the following option a Cold Hot Extra Hot and Ambient COLD TANK The cold tank is manufactured from 304 Stainless Steel which is noncorrosive and inert The temperature of the Cold Tank is controlled by a microprocessor and is set to 5 C but can be changed to 10 C or 15 C 5 C being the id
11. e off position and releasing the pressure by selecting the cold water option until the water stops being dispensed 4 solate the power to the Cube by turning the red and green power switches off these are located at the rear of the machine Remove the power lead as a second safety precaution 5 Remove the top cover from the Cube by undoing the two screws located at the back of the machine then slide the panel backwards and lift up 6 Take out the filter by un clicking the loop at the top of the housing and pulling it in an upward motion If there are two filters in the machine then both of these need to be removed 7 Unscrew the filter housing s and remove the filter cartridge place this to one side as this will need to be re fitted this once you have completed the de scaling procedure 8 Drain 50 100mI of hot water from the machine into one of the empty filter housings using the drainage valve at the rear of the machine Then use this hot water from the machine to make your de scaling solution following the manufacturer s instructions of the descaler Re assemble the filter housing with the de scale solution inside 9 Re fit the filter s into the machine pushing it firmly into place Replace the top cover and re connect the power lead then turn on the red switch at the rear of the machine Turn the water supply back on 10 Place your container under the dispense area and flush through 500m of hot water Allow the solution t
12. eal temperature for a cold drink and the factory default setting The capacity of the cold tank is 1 4 liters waterlogic Better thinking Better water HOT TANK The hot water temperature is controlled by a Microprocessor and is set to 87 C for standard and 95 C for extra hot A thermal cut out is fitted to the Hot Tank to prevent overheating Setting the hot water temperature to 87 C also helps stop scale forming in the hot tank prolonging the 500 Watt element and the hot tank The capacity of the hot tank is 1 3 liters FILTERS The filtration systems on the Cube are designed to reduce dirt and sediment particles from the water Furthermore the Activated Carbon process will remove a whole range of contaminants e g chlorine and pesticides It is important for the UV Sterilization system to be supplied with clean water in order to achieve maximum efficiency There are many kinds of different filter combinations available from Waterlogic to suit local water conditions FIREWALL CHAMBER The Firewall chamber incorporates the in Faucet UV and is made of aluminium and is highly reflective The Chamber houses the UV lamp and quartz spiral as well as the faucet IN FAUCET UV The Unique design allows the faucet area to be sterilized before during and after every dispense There are two types of sensors available the CDS Sensor and UV monitor that detects if the UV lamp is working and the UV sensor that monitors the UVC intensity f
13. ed to ensure that they do not play with the appliance 5 This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised Keep the appliance and its power cord out of reach of children aged less than 8 years 6 Appliances can be used by persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved 7 Children must not play with the appliance 8 If the supply cord or the detachable cord sets are damaged it must be replaced by the manufacturer its service agent or a similarly qualified person in order to avoid a hazard 9 The detachable hose sets and the connection kit used to connect the main water are supplied by the technician Don t reuse the old ones 10 The appliance is to be supplied through a residual current device RCD having a rated residual operating current not exceeding 30mA 11 This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops offices and other working environments farm houses and by clients in hotels motels and other residential type environments
14. ediment before making the connection to the Cube 4 Check the wall socket polarity and then make the electrical connection to the Cube by plugging the power lead in to the socket at the rear of the machine Then connect it to the electrical feed or wall power outlet Turn on the power supply to the Cube 5 Turn onthe red switch at the back of the Cube the machine will now run through a self test cycle Once the self test cycle has completed the filter s will need to be flushed 6 Select the ambient water icon and then the central dispense button and dispense 10 liters of water This will remove excess carbon fines and sufficiently generate the filter The Cube Technical Manual Version 1 May 2014 7 The hot water tank now needs to be filled this is done by selecting the hot water icon then followed immediately by pressing and holding the main dispense button until the tank has completely filled and water is being dispensed Flush through 5 litres of water by continuing to select the hot option Then repeat this process again for the cold option 8 After making sure the hot tank is full of water then turn on the green heater and compressor switch at the rear of the machine 9 Select the hot icon then select and hold the main dispense button immediately after selecting the hot icon 10 Dispense at least 200ml of hot water 11 The machine will now begin to heat chill the water 12 The water temperatures are pre s
15. erlogic as soon as possible 2 Place the unit on a suitable work bench 3 Open the top cover by removing the two screws that fix it in place 4 Visually inspect all electrical connections and power lead 5 Visually inspect all water connections 6 Remove the three screws on top of the Firewall Chamber you may need to remove some of the screws holding the top shelf in place to gain access to the Chamber Inspect the quartz spiral for damage and re assemble 7 Connect to a potable drinking water supply via a 1 4 John Guest tube the supply must be limited to 3bar 8 Connect the power cord to an appropriate power supply and the machine 9 Replace the top cover and re fit the screws 10 Note that the hot tank must be filled before any other tank 11 Select the hot button and then the dispense button until water flows clearly you must dispense at least 200ml of water using the hot option for the tank to begin heating the water 12 Select the cold button and then the dispense button until water flows clearly 13 After cold hot has filled turn on heater compressor switch allow up to an hour for the unit to heat and chill Test water temperatures and ensure the water tastes acceptable 14 Check all of the functions of the Cube 15 Turn off the power and water 16 Turn unit around and drain from rear drain valves if fitted 17 Clean and repack ready for dispatch 18 Waterlogic recommend that all units are fully elec
16. et at the factory to 5 c for the cold water and 8 c for the hot water 13 The water should now be taste tested any hint of taste in the water means the machine needs to be flushed further with an additional 10 litres and then taste tested again 14 The Cube should be sanitized at installation NOTE Should the incoming power to the Cube become interrupted users will need to follow points 8 12 for water to be dispensed This is machine dependent waterlogic Better thinking Better water INSTALLATION KIT The Cube must be installed according to the local guidelines and it is advised that an installation kit be used A pressure reducing valve is supplied with the Cube and must be installed 20cm away from the back of the machine as part of the installation the pressure reducing valve is set to 2 8 bar e The Cube should not be connected to water supplies of unknown bacterial quality or those not already fit for human consumption The Cube should only be connected to a Potable drinking water supply e The filter on the Cube must be changed every 12 months e The UV lamp on the Cube must be changed every 12 months e The cold tank should also be flushed and sanitised every 12 months e Waterlogic International strongly recommends the use of an anti flood device e Figure 1 is the recommended installation kit Fig 1 Waterlogic Installation Kit 1 15mm Compression Inlet 2 Double Check Valve great for carbonated wa
17. hey are in date and are screwed home securely into the filter head Waterlogic recommend filters are changed every 6 months Check that the internal leak detection tray has not filled with water 3 The hot water is not hot and cold water is not cold Make sure the green heater compressor switch is turned on 4 There is hot water flow but cold water is not flowing This may be due to the cold water tank being frozen If so disconnect power supply for one hour to allow the tank to defrost and then flush the cold water system Check the temperature settings are correct If the cold tank is not frozen then check the solenoid valve is operating correctly and being turned on and off when you select the cold option 5 There is cold water flow but hot water is not flowing This may be due to calcium build up in the hot tank or the hot water outlet De scale the hot tank Check the hot water solenoid valve functions correctly and turns on and off when you select the hot option 6 Low flow of cold water or hot water or both Check the building water pressure to the Cube is 45 PSI Check the filters are not partially blocked that the solenoid valves function correctly hot tank calcium build up need to be de scaled cold tank ice buildup needs to be defrosted 7 Bad or plastic taste If the Cube is new it may need flushing for a longer period 22 8 Water leaks Most leaks will be detected by either the internal Cube leak detection system th
18. in valve body only for 5 16 The Cube Technical Manual Version 1 May 2014 37 Ny Part Description 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Drain valve cap only for 5 16 amp 1 4 size Electronic fixing Bracket WL Cube WL Cube Top Cover Black 5 16 1 4 Reducing Straight Connector Filter Bracket CBC 1 Micron 10 Filter Ass y PD use WL Label Hot amp Cold Solenoid Valve 24V 300mm CUBE 1 4 Equal Tee Connector ST UV 15 W Electronic Ballast Ver 3 Power Transformer WL Cube Electronics cover Black WL Cube UI Label WL Logo Cube Main PCB WL Cube UI PCB fixing frame Black Cube Key and Display PCB WL Cube Upper shelf Black WL Cube Silicon Tubing Guide A White Silicon Tube 5 16 for hot water WL Cube Silicon Tubing Guide B White 1 3 liter 500W Hot Tank for Cube 38 39 The Cube Technical Manual Version 1 May 2014 waterlogic Better thinking Better water Speak to a Water Expert USA Canada and Mexico info waterlogicusa com 1402 884 7212 Waterlogic USA 11710 Stonegate Circle Omaha NE 68164 Rest of the world exportsales waterlogic com 353 1293 1960 WLI Trading Ltd Suite 4 2nd Floor Beacon Court Sandyford Dublin 18 Ireland www waterlogic com ENGO0266 20 05 14
19. ly for 10 seconds The items required to complete this procedure are e Rubber Gloves e Phillips Screwdriver e Replacement filter cartridge s e A container that can hold 5 litres e New 13 watt UV lamp e Non abrasive anti bacterial wipe or cloth 1 Put on the rubber gloves to minimise the chance of any contamination to the machine and to protect yourself whilst the servicing procedure is being carried out 2 You will need to stop the water supply to the machine by turning the isolation valve to the off position and releasing the pressure by selecting the cold water option until the water stops being dispensed 3 lsolate the power to the Cube by turning the red and green power switches off these are located at the rear of the machine Remove the power lead as a second safety precaution 4 Remove the top cover from the Cube by undoing the two screws located at the back of the machine then slide the panel backwards and lift up 5 Take out the filter by un clicking the loop at the top of the filter housing and pulling it in an upward motion If there are two filters in the machine then both of these need to be removed 6 Unscrew the filter housing to expose the used filter cartridge This cartridge can then be removed from the filter housing and replaced by a new one Return the filter s into the correct position in the machine ensuring that it is pushed firmly into place as the valves will be reopened by the insertion of the fil
20. o remain in the tank for 5 10 minutes 11 Turn off the water supply to the machine and release the internal pressure by The Cube Technical Manual Version 1 May 2014 waterlogic selecting the cold option until the water stops being dispensed Isolate the power to the machine by switching the red switch at the rear of the machine off and removing the power lead 12 Remove the top cover from the machine Then take out the filter s and unscrew the housing pour the excess water down the drain and re fit the cartridge 13 Re fit the filter s into the machine pushing it firmly into place Replace the top cover and re connect the power lead then turn on the red and green switches at the rear of the machine Turn on the water supply 14 Flush through the hot tank by dispensing water from the hot option You will need to flush approx 4 8 litres of water 15 Smell and then taste the water and flush more water through the tank if needed 16 Using the antibacterial wipes sufficiently clean the exterior panels of the machine including the drip tray and grill ADVISORY ICONS HOT WATER Press and hold the hot water icon for 3 seconds until the icon has illuminated orange select the dispense button and hot water will be dispensed This safety feature prevents hot water from being dispensed accidentally especially by children EXTRA HOT WATER Press and hold the extra hot water icon on the display panel
21. rlogic Better thinking Better water PLASTIC PANELS The molded panels are made from recyclable ABS plastic All the ABS plastic panels are UV resistant and meet the standards of CE and UL Please note that the Cube should not be exposed to direct sunlight Placing the Cube in direct sunlight from a window close to a radiator or in a room of high ambient temperature will affect the efficiency of the refrigeration circuit The Cube Technical Manual Version 1 May 2014 WL Cube Flow Diagram Cold Hot amp Ambient al IN Water 6 66 006 HOT WATER OUT AIR VENT ti SOLENOID SOLENOID z VALVE L SOLENOID 2 COLD WATER OUT VALVE A SOLENOID VALVE COLD 5 SENSOR A COLD TANK CONDENSER SOLENOID ie VALVE oc b w FILTER DRYER COMPRESSOR AMBIENT WATER OUT The Cube Technical Manual Version 1 May 2014 006 waterlogic Better thinking Better water Pre Delivery Inspection Procedures PDI CAUTION Only competent trained technicians should work on Waterlogic products Waterlogic units may weigh over 25KG We recommend caution when lifting Packing materials could present a trip hazard Keep them off the floor Take care not to allow the power lead to get wet If the lead gets wet it must not be used Pre Delivery Inspection Procedures PDI 1 Remove packing straps and unpack unit and visually inspect for any damage Report any defects to Wat
22. rom the UV lamp The Cube Technical Manual Version 1 May 2014 UV LAMP The UV light is a 13 Watt germicidal lamp at a wavelength of 253 7 NM which is very efficient at destroying bacteria in water The UV lamp is situated in the Firewall Chamber surrounded by a quartz spiral that attains NSF standard 55 purification of water The UV lamp must be replaced at 12 months intervals or when indicated by the warning lights and the quartz spiral cleaned by using an ultrasonic bath if needed PCB The PCB Printed Circuit Board is the control unit for the Cube it is responsible for the functions of all the mechanical and electrical parts 24V DC including the solenoid valves touch panel and LED s COMPRESSOR The compressor operates at 220 240V at 50Hz or 120V at 60Hz It uses 55 grams 1 94 Oz of R134a non Ozone depleting refrigerant gas WATER PIPES AND FITTINGS The inlet and the internal water circuit pipe size are 1 4 and 5 16 The entire internal water circuit and all the components which come in contact with water are food grade NSF approved The cold and ambient water tubing inside the machine should not be exposed to water above 25 C WATER VALVES Dispensing of water to the customer is achieved by means of a 24V DC electrical solenoid valve The valves are energized every time the customer touches the dispense button for a drink DC voltage is used to give a positive and quieter action of the solenoid valve wate
23. ter 7 Remove the UV lamp by unplugging the UV loom and pulling the lamp upwards 8 Examine the UV loom for any discolouration or wear if there is any visible remove the loom and replace with a new one 9 Reconnect and replace the UV lamp assembly making sure not to touch the new UV lamp with bare hands as this will shorten the life of the lamp 10 Inspect all of the electrical and water connections on the machine and take any action necessary to prevent a fault from occurring Li Rattar thinking Rattear Better thinking Bette 11 Check the faucet nipple for any calcium build up or any visible damage and clean or replace it if necessary 12 Reassemble the machine and secure all panels with screws 13 Check that the air gap around the machine is sufficient and there is nothing blocking the ventilation 14 Reconnect the power to the machine and turn the red switch at the rear of the machine to the on position Turn on the water supply 15 T he filter s now need to be flushed Do this by selecting the ambient water option and dispensing 10 liters of water through the machine This will sufficiently generate the filter and remove any excess black carbon fines 16 The green heater and compressor switch can now be turned on 17 Select the hot icon then select and hold the main dispense button immediately after selecting the hot icon 18 Dispense at least 200ml of hot water 19 The machine will now begin to heat
24. ter 3 Adjustable Pressure Reducing Valve 4 Integral Isolator 5 Pressure Gauge Port 6 Waterblock 7 1 4 Pushfit Outlet The Cube Technical Manual Version 1 May 2014 Operating Instructions ENERGY SAVING FEATURE The Cube has an energy saving feature that minimizes power consumption when the machine has not been operated for 3 hours If the sleep mode on the Cube has been deactivated the machine will automatically enter sleep mode after 72 hours of no use The Cube can be taken out of sleep mode by touching any of the buttons Please note the hot tank will take 10 12 minutes to reach optimum hot temperature after the machine has been taken out of sleep mode DISPENSING YOUR CHOICE OF WATER IS VERY SIMPLE AS FOLLOWS 1 Place your cup centrally in the dispensing area 2 Select the type of water you wish to be dispensed and press touch the corresponding icon 3 Once the icon you have selected is illuminated select the dispense button in the middle of the button panel 4 Keep the dispense button depressed until your cup has reached the desired level and then release the button HOT WATER CAUTION e Always place cup mug in the centre of the drip tray e Always use a ceramic cup or a cup suitable for use with hot water e Do not hold cup or place hands in dispensing area whilst dispensing water e Do not dispense water in a stop start style of vending e Hold the button continuously until cup is full
25. thinking Better water 296mm W x 425mm D x 375mm H 18Kg 220 240 Volt 50Hz 500W 2W 120W 13W 635W 55g 1 940Z 1 4L 1 3L 1 4 Hose 2 6 0 26 4 14 0 414 3 0 0 3 1 0 Ipm 1 3lpm 5 C 15 C 415 59 80 C 95 C7 17 6 F 203 F The Cube Technical Manual Version 1 May 2014 25 End of Life Non Eu Countries At the end of this products life please ensure that it is disposed of in an environmentally friendly manner which is in line with your Country requirements guidelines WEEE EU ONLY H Please be aware that our products are covered by the Waste Electrical and Electronic WEEE directive 2002 96 EC The symbol shown above denotes that the product should not be disposed of with general household waste Please contact your supplier service agent who will arrange for the collection and disposal of this product ROHS All Waterlogic machines comply with EC Directive 2002 95 EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electrical Equipment RoHS BIOCOTE ANTI MICROBIAL SOLUTION For your added protection this product incorporates BioCote antimicrobial technology Silver in the form of silver ions is the active ingredient utilized in BioCote This silver technology is manufactured into the surface of our products giving them built in sustainable antimicrobial protection BioCote s silver technology has been tested by
26. trically PAT tested on site by the commissioning engineer as damage may have occurred during transit to the unit s final destination waterlogic r thinking Retter water or Thinking Better water V Installation Procedures 1 Mount the Cube on a firm level surface so the machine cannot topple or fall over A 50mm air gap is required the whole way around the machine to allow for sufficient ventilation The Cube must not be installed in direct sunlight adjacent to a heat source or in an ambient room where the temperature is above 30 C or below oC 2 It is advisable that the power and water supply be within a 2 metre range of the machine the isolation for the water and electricity should be easily accessible The supply of water must be from a potable source and the machine should not be installed using an extension lead 3 Make the water connection to the Cube via a length of flexible pipe with the pressure reducing valve that has been supplied installed 20cm away from the machine before the connection into the back of the machine is made This will bring the pressure down to the ideal working pressure of 3bar Minimum operating pressure for the machine to work suitably is 2 6bar The minimum incoming flow rate is 1 2 litres per minute At pressures higher than 3 2bar the machine will not function correctly and this can lead to leaks The water should be from a potable source and should be allowed to run clear of any s
27. ube Blue O D 1 4 43 CBC 1 Micron 10 Filter Ass y PD WL Labe 44 Hot amp Cold Solenoid Valve 24V 300mm CUBE 45 5 16 1 4 Reducing Straight Connector 46 JG Equal Elbow Connector 1 4 47 5 16 1 4 Reducing Straight Connector 48 JG LLD PE Tube Blue O D 1 4 34 35 The Cube Technical Manual Version 1 May 2014 waterlogic Better thinking Better water Main Parts List WL Cube Mains Parts Illustration 36 waterlogic Better thinking Better water Ne Part Description O ON OB WN gt WL Cube Side panel left Silver Mark IV Al Mirror no gauze Spout 18mm for CUBE WL Cube FW fixing bracket WL Cube Front frame panel Black WL Cube Front cover Silver WL Cube Spout assembly bracket Silver WL Cube Drip tray body Black WL Cube Drip tray grill Silver Rubber feet for Cube WL Cube Base plate Black 1 4 Equal Elbow Connector ST Leak Detection Sensor Bracket Leak containment tray Clip sensor 0 5mm 1 4 stem Elbow connector Solenoid Valve 24 DC Single Spring Load Cube cold tank 1 4 Litre Compressor Domestic Filter Dryer Chinese WL Cube Side panel right Silver BulkHead Fitting 1 4 x 1 4 ST Socket for Plug Connection Domestic PST 101SL AC Power Fuse Holder with Fuse Switch Power Red Switch Heater Compressor Green Cooling Wire Condenser for Cube Micro Door Lock S W only WL Cube Micro switch cover Gray WL Cube Back panel Black Fan Motor DC 24V Dra
28. ur the excess water down the drain and re fit the cartridge 13 Re fit the filter s into the machine pushing it firmly into place Replace the top cover and re connect the power lead then turn on the red and green switches at the rear of the machine Turn on the water supply 14 Select the hot icon then select and hold the main dispense button immediately after selecting the hot icon 15 Dispense at least 200ml of hot water 16 The machine will now begin to heat chill the water 17 Inspect the faucet nipple and clean or replace if it is damaged or if there any calcium built up around it 18 Using the antibacterial wipes sufficiently clean the exterior panels of the machine including the drip tray and grill blat Rattar thinking Rottor Better thinking Bette DE SCALING You will need the following items e A Phillips screwdriver A pair of rubber gloves e De scale solution or powder e A funnel or large syringe e A container that can hold 5 litres e Non abrasive anti bacterial wipe or cloth 1 Put on the rubber gloves to minimise the chance of any contamination to the machine and to protect yourself whilst the de scaling procedure is being carried out 2 Allow the machine to heat the water up to normal operating temperature as the water inside the tank needs to be hot for the de scaling solution to work effectively 3 You will need to stop the water supply to the machine by turning the isolation valve to th
29. wi e waterlogic F R E WA L L Better thinking Better water WL Cube Firewall Technical Manual VERSION 1 Technical Manual Welcome to your new Waterlogic machine This Technical Manual is to help you get great tasting water cup after cup by making the most of the product s features Index Machine Overview WL Cube Flow Diagram Pre Delivery Inspection Procedures PDI Installation Procedures Operating Instructions Maintenance and Servicing Sanitizing De scaling Advisory Icons Fault Finding Technical Specifications and Warranties End of Life ROHS BioCote Electrical Wiring Diagram 120V Electrical Wiring Diagram 230V Dip Switch Setup Wetted Parts List Main Parts List 00 11 14 16 17 19 21 22 24 26 26 26 27 28 29 32 36 Declaration Waterlogic International Ltd 1 The installation maintenance and sanitizing procedures must be carried out by persons trained by Waterlogic International or their approved distributors Do not remove any panels or covers unless acceptable in this instruction 2 When any abnormal case happens firstly unplug the appliance 3 This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety 4 Children should be supervis
Download Pdf Manuals
Related Search