XSD27ZIR-2 - User Manual
Contents
1. 5 XSD27ZIR 2 Day Night 600 TVL IR Soeed Dome CCTV Camera 27x Optical Zoom and 100m Nightvision User Manual XSD27ZIR 2 User Manual Contents 1 PRODUCT INTRODUCTION Li FEATURES A ncaa ena 3 b2 FUNCTONS 4 Lo PACKAGED CONTENTS EN 4 2 INSTALLATION 21 INSTALEA NON WARNING aiia 5 8 3 OPERATING BASICS 4 MENU SETTINGS 4 1 MAIN 10 4 2 SYSTEM INFORMATION c ccecsssscscsssssccssseccesssscessssccssevecssavecsssseseessueeessusessnusesaueceesvesessnees 11 4 3 ADDRESS SETTING viceccscccssssesccssecccsssssssssessssecessuecesssssecsssseesssveseessecsessneceesnecessnecessnnseesen 12 4 4 MOTION PAN TILT SETTINGS cccsssscsssssssssssssssssesssssvscssssecessuscesssisecssssesessveretssesseenentees 11 AS PATTERNS 13 4 6 CAMERA eccccssecccssecccssssecsssseesvecesssseessssecsssvecesssesesssesesssuseesssusesssasecssnsessssvesstsvesersveseessnnses 14 AF CRUISE TOUT 14 4 8 DISPLAY SETUP ceccsssscscssscssssssssssessssssscessuscesssuseessssecssusecsuccessusesssusecesssesssuseessescessnnsesssnses 15 4 9 SETTING 15 5 TROUBLESHOOTING 5 1 TROUBLE SH2. handling of this product The recycling of materials helps to conserve our natural resources For more detailed information about recycling of this product please contact your local council office your household waste disposal service or the shop where you purchased the product In addition you can find further information online at www environment agency co uk XSD27ZIR 2 User Manual Prior to installation and use of this product please observe the following points Installation and servicing should be carried out by qualified service personnel It is important that the dome camera is not left in a position where the camera is pointing directly at the sun or other extremely bright light source This may result in CCD damage and poor image quality installation position must be as far away from high voltage sources as possible dome cover is high quality optical product Try to avoid touching it as any scratches or marks left on the surface could affect image quality we recommend the use of cotton gloves when handling Please refer to the installation manual for further guidance In order to get the optimum image at all times the dome cover should be cleaned periodically Be careful when cleaning only hold the cover edge avoiding direct contact with the dome cover Acid from fingerprints will damage the coated surface of the dome cover Direct contact with hard objects could lead to deterioration of the image
3. Please use a soft clean cloth or similar to clean interior and exterior surfaces of the cover A neutral detergent non acid based or high grade furniture detergent may be used Only use replacement parts recommended by your local distributor After replacement repair of this unit s electrical components take a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry When unpacking the dome the Pan Tilt module should be handled with care Do not place in a position where something could rub against or fall onto the housing When installing camera module avoid touching any parts which could be easily damaged such as the optics and PCB sure all power and telemetry connections are complete before powering up camera Do NOT install the camera close the air outlet of an air conditioning unit as the camera may be affected by the resulting water condensation XSD27ZIR 2 User Manual 2 1 Wiring Power Supply Cable Yv v gt Video Cable R5485 Connection Monitor CATS Cable gt Video Cable 4 or DVR Video and or R5485 is Connection Cable Xvision to DVR Yy Speed Dome Controller v Model 502 30 791 7 Connections 5485 Connection Ensure that the camera and PTZ controller keyboard DVR ar
4. a sequence of user defined Preset points The tour can then be easily launched by the PTZ controller 1 3 PACKAGE CONTENTS The packaged box for XSD27ZIR 2 comes with the following items XSD27ZIR 2 Speed Dome Camera Wall Bracket Power Supply Screws Allen key User Manual Should any of these items be missing please contact your local distributor XSD27ZIR 2 User Manual 2 INSTALLATION INSTRUCTIONS 2 1 Warning yi RISK OF ELECTRIC SHOCK m CAUTION REDUCE THE RISK OF ELECTRIC SHOCK USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING This symbol is intended to alert the user to the presence of non insulated dangerous voltage CAUTION This symbol is intended to alert the user to presence of important operating and maintenance Servicing instructions in the literature accompanying the appliance Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection This symbol on the product or on its packaging indicates that this product should not be treated as household waste Instead you should make arrangements for the recycling of this unit By ensuring this product is disposed of correctly you will help to prevent harm to the environment and avoid possible health issues which may be caused by inappropriate waste
5. shown the number highlighted lt PATTERN gt To set a pattern select this option and the following menu is displayed PROGRAM PATTERN MOVE THE CAMERA TO THE STARTING POSITION IRIS OPEN TO CONTINUE Move the camera to the chosen starting position for the pattern and press the OPEN button on the PTZ Joystick Keyboard to begin recording the screen will then display the amount of memory used as a percentage for that particular pattern STORAGE USED lt PCT gt 1 Move the joystick through the desired route pattern and then press the lt OPEN gt button to save the desired pattern The user will then be reverted back to the previous menu once completed The same process can then be repeated to set up to 4 different patterns CLEAR CURRENT PATTERN Clears the predefined pattern i e defined by the pattern number highlighted in the menu CLEAR ALL PATTERN Clears all predefined patterns BACK returns to the previous menu m EXIT exits the OSD menu 12 XSD27ZIR 2 User Manual 4 6 CAMERA This allows the user to change the parameters for the camera s lens The following menu will be displayed CAMERA DIGITAL ZOOM OFF AUTO IRIS ON ZOOM SPEED 7 BACK EXIT DIGITAL ZOOM Manually switch the digital zoom ON or OFF AUTO IRIS Manually switch the Auto Iris ON or OFF ZOOM SPEED Set the Zoom s speed range between 1 7 BACK returns to the previous menu m EXIT exits th
6. OOTING TABLE iccccssecssssesscssssssssssessssssscesssecesssscessvessssssveessuscessuscesseesessneses 15 XSD27ZIR 2 User Manual 1 PRODUCT INTRODUCTION 1 1 FEATURES Advanced Pan Tilt Zoom functionality Automatic recognition for RS 485 control protocol Recognizes 2400 4800 9600 Baud Rate Compatible with PELCO D P protocols Complete 360 degree rotation and 90 vertical rotation allows surveillance without any blind spots High speed Pan Tilt rotation on vector drive technology that ensures the Pan amp Tilt motion takes the most efficient and shortest path when viewing Presets Features an advanced micro stepping motor that allows the Pan Tilt rotation reach speeds of 0 05 degree sec This allows the video image to be more accurate and stable under high magnification times Presets and Tours Maximum of 256 Presets every Preset includes a lens magnification and viewing angle position Records up to 1 predefined tour which consists of a maximum of 20 Presets Set up the left and right border of specified zones Execute Pan Tilt Zoom functions at specified speeds A Preset can include a continuous 360 scan On Screen Display OSD Menu Built in OSD screen menu that allows you to easily access and modify the speed dome s operating parameters settings Operating information such as horizontal vertical viewing angle magnification of the lens and Preset in use can be displayed on scree
7. T SYSTEM Reboot the camera m EXIT Exit the OSD menu 4 2 SYSTEM INFORMATION The System Information option displays the speed domes general operating parameters and information which is displayed as follows SYSTEM INFORMATION COM 9600 N 8 1 ADDRESS 1 SOFTWARE VERSION V5 2 BACK EXIT Please Note The options described with the System Information cannot be changed within this menu The System Information menu items are explained as follows Baud Rate Parity Bit Date Bit and Stop Bit ADDRESS Camera ID for PTZ control i e between 0 255 SOFTWARE VERSION Current software version BACK Returns back to the previous menu m EXIT Exits the main menu 4 3 ADDRESS SETTING The address setting menu is displayed as follows ADDR SETTING ADDR TYPE HARD ADDR SOFT 255 ADDR HARD 1 BACK EXIT XSD27ZIR 2 User Manual The speed domes address type ADDR TYPR can set between either SOFT automatically obtains an address or HARD address is physically set via the dip switches Once selected press the lt OPEN gt button to save any changes Similarly uses the joystick to scroll through the other options to set either the ADDR SOFT or ADDR HARD Once completed you can select BACK or EXIT options to leave the setup 4 4 MOTION PAN TILT SETTINGS The Motion option menu is displayed as follows MOTION lt FRAME SCAN gt POWER UP PARK TIME PARK ACTION BACK EXIT lt FRAME SCAN gt All
8. e connected by a suitable CAT 5 cable If you have more than 1 dome please set incremental addresses for each camera Please ensure that the camera s setting i e Baud Rate Camera ID etc match correspond between the Speed Dome and controlling device Video Connection Use a BNC cable to connect the speed dome directly to a monitor DVR Power Supply Connection Ensure that the camera to a suitable power outlet ensuring that you use the power supply provided Please Note When you turn on the power for speed dome it will begin to initialise for a few seconds as the camera runs a self test protocol Handle with care whilst installing the camera ensuring that none of the moving parts are damaged Use shielded cable and mix with other cables Keep the PTZ dome camera or signal transmission cable away from high voltage equipment or cables at least 50 meters and ensure that is lightning and surge protection Do not use the PTZ dome camera in environments of extreme temperature or humidity The temperature should be between 25 and 50 with humidity lt 90 XSD27ZIR 2 User Manual 3 OPERATING BASICS To control the PTZ functions you will need use a compatible PTZ joystick keyboard controller DVR These instructions are based upon Xvision s XSDZ 3DM Speed Dome Joystick controller Please Note PTZ manufacturers may have different operational configurations Please r
9. e OSD menu 4 7 CRUISE SETTING TOURS The Cruise Setting allows the user to combine up to 30 Presets as continuous tour movement The following menu is displayed as follows CRUISE SETTING DWELL TIME lt SECS gt PRESET1 PRESET2 PRESET3 PRESET4 PRESET5 PRESET6 7 PRESET8 PRESET9 PRESET10 DWELL TIME lt SECS gt Refers the waiting time between different cruises PRESET LIST Allows the user to choose which Presets are active The user can select which specific Presets to use maximum of 20 Presets 10 Presets per page are displayed Using the controller to scroll down the user can see the remaining presets on the second page of the Cruise Setting menu Using the joystick select which Presets are to be used in the Tour and press the PRE button to select the chosen Preset The user can then choose to switch the Preset between ON or OFF during the cruise BACK returns to the previous menu 13 XSD27ZIR 2 User Manual 4 8 DISPLAY SETUP This option allows the user to configure the type of information that can be displayed on screen during normal operation The following menu will be displayed DISPLAY SETUP PRESET LABEL ZOOM P T DEG BRIGHT DATA IR DATA BACK EXIT PRESET LABEL Displays the Preset number currently in operation ZOOM Displays the current magnification position of the lens P T DEG Current vertical and horizontal angle of the lens BRIGHT DATA The current e
10. efer to the manufacturer s operating manual for further details Setting up Presets A Preset is a fixed position of the camera and its lens which is defined by the user Preset includes both the lens position i e horizontal vertical position and its state i e magnification and Iris Use the PTZ controller to set the camera chosen position zoom and iris Using the controller press the SET button then key in the chosen Preset number i e number 9 and press the PRESET PRE button to store the chosen parameters To Call a Preset the chosen Preset number and press the PRE button to move the camera to the chosen preset parameters i e position Zoom and Iris A list special defined Presets recognised by the Speed Dome are listed below as follows SPECIAL PRESETS FUNCTION 95 CALL Reserve Preset xxx XXX CALL Call Preset xxx Delete all presets Preset 31 40 cruise 360 Scan XSD27ZIR 2 User Manual 4 MENU SETTINGS 4 1 Main Menu The items in the main menu are listed below as follows SYSTEM INFORMATION Displays the camera s general information ADDR SETTING Camera s operating protocols MOTION PTZ Movement Settings PATTERNS Configure Patterns CAMERA Configure settings for the lens CRUISE SETTING Configure Cruises DISPLAY SETUP Configure displayed on screen information RESTORE FACTORY DEFAULT Restores the factory default setting REBOO
11. n for the operator XSD27ZIR 2 User Manual 1 2 FUNCTIONS Setup of address code The XSD27ZIR 2 allows the user to manually set the camera s protocols such as its ID address baud rate and RS485 protocol Automatic turnover When the camera reaches its maximum tilt position by continuing the movement on a PTZ controller the lens will automatically flip 90 and rotate 180 horizontally Therefore the user will not have to scroll all the way back to the opposite viewing angle allowing them to a achieve 180 continuous surveillance Reserve and Call Preset Users can store up to 256 Presets which can be set via the speed dome itself or via a compatible controller 5 1 Control The camera s lens can be fully controlled via a PTZ controller such as the zoom and focus Additionally if you want to reset lens i e auto focus the user can simply shake the PTZ controller s joystick left to right or set up a relevant Preset Night vision The Speed Dome will automatically switch to its nightvision mode once the illumination levels drop to a user specified level Optional infrared lighting is required for the camera to view in nightvision mode Patterns The camera can store up to 4 patterns which can then be launched by the PTZ controller as predefined presets i e numbers 84 85 86 and 87 Tours The camera can store 1 Tour which allows the camera to move to a user defined pattern which itself is
12. ollows o No action o CRUISE Launches the Presets Cruise Tour o PATTERN 4 Launches Pattern 4 o PATTERN 3 Launches Pattern 3 o PATTERN 2 Launches Pattern 2 o PATTERN 1 Launches Pattern 1 o PRESETS 8 Moves preset position 8 PRESETS 1 Moves preset position 1 o FRAME SCAN Launches a frame scan horizontal scan o RANDOM SCAN Launches a random scan o AUTO SCAN Launches an auto scan lt PARK TIME gt Allows the user to configure the camera s waiting time during presets i e the range can be set between 15 and 250 seconds lt ACTION gt Allows the user to set the speed domes action when the speed dome is idle The options that can be chosen are as follows NONE No action o REPEAT LAST Repeats last action o CRUISE Launches the Presets Cruise Tour o PATTERN 4 Launches Pattern 4 o PATTERN 3 Launches Pattern 3 o PATTERN 2 Launches Pattern 2 o PATTERN 1 Launches Pattern 1 11 XSD27ZIR 2 User Manual o PRESETS 8 moves Preset position 1 o PRESETS 1 moves Preset position 8 o FRAME SCAN Launches a frame scan horizontal scan o RANDOM SCAN Launches a random scan o AUTO SCAN Launches an auto scan 4 5 PATTERNS A Pattern allows the user to record a specific path pattern displaying the following menu PATTERN PATTERN NUMBER lt PROGRAM PATTERN gt CLEAR CURRENT PATTERN CLEAR ALL PATTERN BACK EXIT PATTERN NUMBER Choose a pattern number range between 1 4 as
13. onnection disconnected cable Image is not consistent or Video cable is not connected Change the cable and or test not clear properly or is faulty ona shorter run Mains power or another Check the camera on a short cable interfering with video cable run quality possibly running next to the video cable 15
14. ows the user to setup the camera s maximum left right position during a scan and displays the following menu FRAME SCAN SET SCAN POSITION CLEAR FRAME SCAN FRAME SCAN SPEED BACK EXIT To setup the left right maximum positions select SET SCAN POSITION and the following menu will be displayed SET FRAME SCAN LEFT LIMIT POSITION IRIS OPEN TO CONTINUE To set the LEFT LIMIT POSITION move the joystick to the desired location and press the lt OPEN gt button on your controller to save Once saved the user will be prompted to set RIGHT LIMIT POSITION as shown below SET FRAME SCAN RIGHT LIMIT POSITION IRIS OPEN TO CONTINUE 10 XSD27ZIR 2 User Manual Follow the same procedure as detailed above to set the RIGHT LIMIT POSITION Once this is successfully completed the system will automatically revert back to the previous menu To clear any previous preset positions select the CLEAR FRAME SCAN option and the following menu will be displayed as in the image below CLEAR FRAME SCAN WAIT Select CLEAR FRAME SCAN to delete any previous presets Once complete the user will be taken back to the previous menu FRAME SPEED SCAN allows the user to set the movement i e amp Tilt soeed The speed can be set between 1 and 32 please note the larger the number set the faster the speed lt POWER UP gt Allows the user to set the speed domes action upon being powered up The options that can be chosen are as f
15. xternal illumination level BACK returns to the previous menu EXIT exits the OSD menu 4 9 IR SETTING The function allows the camera s IR LEDs to be configured with the following menu being displayed DISPLAY SETUP PRESET LABEL ZOOM P T DEG BRIGHT DATA IR DATA BACK EXIT MODE Configure the IR LED s operating mode There are 3 options to choose from AUTO IR s turn on automatically ON or OFF IR ON SENS Set the IR LEDs threshold value before the IRs are switched IR OFF SENS Set the IR LEDs operating level before the IRs are switched off IRIRIS MODE Use to set the illumination mode of IR LEDs that can be used to save power and allow manual control range between 1 3 CURRENT VALUE Current IR illumination model of the IR LEDs BACK returns to the previous menu 7 EXIT exits the OSD menu 14 XSD27ZIR 2 User Manual 5 TROUBLE SHOOTING Trouble Possible Reason Solution No movement or image Power cable is connected Correct the connection when the power has been incorrectly switched on Power Supply is faulty Change the Power Supply Faulty Video connection Correct the connection Not enough power Power camera locally No movement when the Incorrect baud rate and ID Re set the DIP Switch power has been switched on code but has an image RS485 5 cable Check RS 485 connection disconnected short circuited cable or connected incorrectly wiring cable Check RS 485 c
Download Pdf Manuals
Related Search