401G user manual
Contents
1. The module cannot transfer the call and send the message Poor signal Poor contact of the SIM card No charge of the SIM card Check the connection of antenna Check if the SIM card is well plugged in then press QJ button to restart the module Please prepaid the SIM card in time Sub Units Max support 3PCS 401G Operation temperature 10 C to 55 C The module sounds DI Di at intervals The connection between the module and the indoor unit is cut off Check the connection between the module and the indoor unit Optional Indoor unit Any of our 4 wires indoor units which should be had the function of connecting with 3pcs extension unit When talk with phone the voice which outdoor can heard is very low Talk volume is too low Under talk mode double click unlock key on the mobile phone to unlock the door Bd Away LED red on No SIM card on the module or poor contact of SIM card Signal LED red on Poor signal Check the connection of antenna and installation position Signal LED red flash No signal Check the connection of antenna Check if the SIM card is well plugged in then press button to restart the module 18 192. turns off without turn on the green LED which means successfully send the message manual setup Remark 3 Message LED 10 Volume setup Under talking mode double click on the mobile phone to increase talk volume Under talking mode double click on the mobile phone to decrease talk volume Remark Successfully setup with DI failure with DI DI 14 15 Operation 13 Outdoor unit call remind call transfer Under away mode when outdoor unit calls in the power LED green flashes and transfer the call to the transfer phone number A If you have setup two transfer phone number when outdoor unit calls in the call will be transferred to the 1st phone number If the visitor call again within 10 seconds the call will be transferred to the 2nd phone number B If you only setup the 2nd transfer phone number when outdoor unit calls in the call will be transferred to the 2nd phone number directly Remark To reach the call transfer function you will turn on away mode and setup the call transfer phone number 14 Alarm for communication problem If the module sounds DI DI at intervals meanwhile away LED green flashes which means there is communication problem between the module and the indoor unit Please check the wiring 16 Power LED green on Power LED green flash Message LED red on Message LED green on Message LED green flash 9uUttaao gt Signal LED green on Signal LED red
3. on Signal LED red flash Away LED red flash Away LED red on Away LED green on Away LED green flasht Fox Eb E M ELE e E NOP Se S28 gt 5 Means under talking mode Means outdoor unit calls in Means message is sending Means failure to send the message Means under reset mode Mean signal is normal Means signal is weak Means no signal Means under registration mode Means no SIM card or poor contact of SIM card Means away function is ON Means communication problem between the module and the Indoor unit 17 Troubles shooting guide Specification Problem The module totally cannot work Possible reason The module hasn t connected with power The module is under OFF mode Solution Check if the power is well plugged in Refer to Operation 2 Power ON OFF Model No Item 401G Power Supply DC13 5 15V 600mA Outdoor unit cannot call The module is no response The connection between indoor unit and the module is cut off The connection between indoor and outdoor unit is cut off The module is under OFF mode Check the connection between indoor unit and the module Check the connection between indoor and outdoor unit Refer to Operation 2 Power ON OFF Connection Power consumption Support Frequency In series 13 5V 20mA 5mA Standby GSM900 DCS1800 13 5V 50mA 10mA Working
4. 89 3 VIP UNLOCK TEL2 Modify VIP unlock menu as right 4 VIP UNLOCK TEL3 5 Binding PWD Send modified menu to 401G by SMS If setup successfully when phone numberc123456789 call 401G module s phone number it will unlock the door directly 6 5 Check unlock records a Any phone number Send SMS IUE Laa to 401G module s phone number the user will get the replied SMS which indicated the latest 5 unlock records b Transfer phone number Press and hold 2 button till it sounds DI the user will get the replied SMS which indicated the latest 5 unlock records Remark 1 Only the 1st transfer phone number can receive latest 5 group of unlock records by pressing button The 2nd transfer phone number need to send SMS Admin password 44 to get records 2 The function of pressing to get unlock records is not available if the unit is only setup the 2nd transfer phone number 3 Refer to operation 6 2 to see how to setup transfer phone number 11 Operation Format of unlock record message phone number date time door station number For example 123456789 2013 03 13 15 15 15 DOOR1 It means phone 123456789 unlock Door1 on 15 15 13th March 2013 6 6 SMS to setup individual function a Setup away mode Turn on away mode send SMS to 401G Turn off away mode send SMS eei to 4010 If away mode is turned on but without transferring phone number the SMS will be replied Tran Tel1 S
5. GSM MODULE USER MANUAL NN 401G i 0 0080 X 20 FE 0 R amp TTE RoHS X 1509001 15014001 OHSAS18001 2 Content Product introduction meme nne nnennenennnennenenenenneneneneenennnen 3 Feature and parts EE 4 Operation 5 LED status indication 17 Trouble shooting e 111 E 18 Specification cecidi nm Uer ae Adr UAI DI e e LS 19 Product introduction Thank you for purchasing our products of building intercom system series please read the instruction carefully and follow the directions before installing the products Any problem regarding to the products please inquire your supplier General features 7 Enable the outdoor unit remote talk with telephone mobile phone 7 Enable the telephone mobile phone remote unlock the door SMS remote setup the module incl system menu function menu VIP unlock menu 7 VIP unlock the door without charge Product s function Be connected with our 4 wired video door phone which system is able to connect with at least 4pcs indoor units with intercommunication function to reach the function of remote talk or unlock between phone and outdoor unit Also the SMS remote setup module function is available CAUTION To avoid the risk of electric shock please don t remove cover or back Please ask professional person if maintenance needed Remind users that important operation and maintenance guide are included in the atta
6. a high position which is not convenient for operation you can connect mode set ON with an external switch through away extension terminal to setup away mode With the external switch you will hear the module sounds a short DI when you press the switch Press J button till the module sounds DI DI meanwhile away LED green turns off means AWAY which means the away mode ON Press the switch again you will hear the module sounds DI DI mode set OFF Remark 1 if you do not setup the transfer phone number when you turn on away mode the module will which means the way mode OFF remind you to setup the transfer phone number with a long DI Remark 1 Press and hold the switch till the module sounds a short DI which means the module is 2 The function is invalid when the indoor monitor is turned on away mode which can automatically successfully restarted 2 If you don t setup the transfer phone number you will hear the module sounds a long DI when you press the switch for the first time which remind you to setup the transfer phone number Record video 9 Unlock Under talking mode double click unlock key on the mobile phone 12 Remind when send the message Message LED red on means the module is sending the message After message LED red turns green means message send failure When message LED green to unlock the door Remark the unlock key is default to 0 Refer to Operation 6 2 System
7. ched user s manual The manufacturer reserves the right to change or modify designs features functions and specifications without any prior notice for the improvement and promotion of product s quality please refer to the real products 13062801 gt Features and parts GSM antenna Software programming terminal ID Connection terminal SIM card SIM card slot Button area E Away button Away LED Reset button Signal LED D Message button Message LED Power button Power LED Unlock record check Remark 1 During the operation please press the center of buttons As above picture 2 The SIM card should be had the caller ID display function please consult with your local GSM network operator 3 The unit is only supported GSM900 1800 network 1 Power status indication After connecting to the power the power LED red will be lighted all the time Away LED red starts to flash which means the module is under registration while the away LED red stops flashing and the signal LED green turns on that means the module starts to work Remark 1 Power LED 8 away LED 2 If there has the other LED flasheing please refer to the Features and parts or LED indication introduction 2 Power ON OFF a When the module is under OFF statu
8. et NO TELEPHONE NUMBER b Setup 1 transfer phone number Send SMS to401G Remark Max support 20 digits not allow or c Setup 2 transfer phone number Send SMS 401G Remark Max support 20 digits not allow or 12 Operation d Setup unlock key Send SMS IKZ WIVES to 401G stands for digit from 0 to 9 Remark If you get replied SMS SET OK means setup successfully If you get replied SMS SET FAIL means setup unsuccessfully 7 Help Send SMS to 401G module s phone number the user will get the replied SMS as below SMS Function commentary PASSWORD 00 Get All Menu Get All Menu PASSWORD 11 Get System Menu Get System Menu PASSWORD 22 Get Function Menu Get Function Menu PASSWORD 33 Get VIP Unlock Menu Get VIP Unlock Menu PASSWORD 1 1 Set Away ON Set Away ON PASSWORD 1 0 Set Away OFF Set Away OFF PASSWORD 2 TELEPHONE NUMBER Set Transfer Telephone Number 1 Set Transfer Telephone Number 11 PASSWORD 3 TELEPHONE NUMBER Set Transfer Telephone Number 2 Set Transfer Telephone Number 21 PASSWORD 4 UNLOCK KEY Set Unlock Key From 0 To 9 Set Unlock Key From 0 To 91 13 Operation Operation 11 Away extension terminal 8 Away setup Press t button till the module sounds DI meanwhile away LED green turns on means AWAY When the module is installed in
9. s press button it will sound DI and then enter into the standby mode meanwhile the power LED red lights on b When the module is under standby status press button it will sound DI and all LED will turn off that means the module enter into OFF mode 3 Restart If the module is worked abnormally please press button to restart the unit Remark 1 If the SIM card loose contact please pull out the SIM card and insert it again and then press button to restart the module 2 Every time when you insert the SIM card you have to press button to restart the module or it may not read the SIM card Operation 4 Reset Press and hold button till the signal LED green flashes which means the module is entering into the reset mode When the module sounds DI means you have reset the module successfully 5 Binding the mobile phone number to the GSM module Send SMS to 401G module s phone number the user will get the replied SMS which include the detail of the menu which include the binding password which means the mobile phone number has been successfully bound to the module lt Unlock Key 0 0 5 Binding PWD 2707 Binding password autogeneration Remark 1 You have to bind the mobile phone number for the initial using or you can not setup the functions via SMS 2 If you want to bind another mobile phone number just do the same as the above operation 3 If you want to cancel
10. the bound mobile phone number you could reset the module or change the administration password Please refer to the function menu setup of Part 6 3 4 The administration password is defaulted to 8888 5 If you changed the binding password the bound mobile phone number can not setup the menu Anymore 5 Save the SMS for more convenient operation 6 SMS to setup the module should be bound the mobile phone No First 6 1 To get the setup menu Send SMS nlt to 401G module s phone number the user will get the replied SMS which include the detail of three menu System Menu Function Menu and VIP Unlock Menu System Menu VIP Unlock Menu Remark Save the SMS for more convenient operation Operation Operation 6 2 System menu setup Send modified menu to 401G by SMS If get replied SMS SET OK means setup successfully Send SMS to 401G module s phone number the user will get the replied Modify system menu as below SMS as below SMS Function commentary Example 2 1 Away Set 0 1 ON 0 OFF Away setup 0 Turn off away mode 1 Turn on away mode Factory setting default to 0 If unsuccessfully setup the unlock key and away mode is 1 Away Set 1 1 ON 0 OFF 2 Tran Tel1 Set 1st transfer phone number setup Max support 20 digits not allow or turned on but without transferring phone number
11. the user 2 Tran Tell SetNO TELEPHONE NUMBER T ud deas 2nd transfer phone number setup Same operation as the above More detail information Will get the SMS by 401G module as below 3 Tran Tel2 Set referring to Operation 13 Call remind transfer 4 Unlock Key FAIL 0 9 4 Unlock Key 0 0 9 Unlock key setup Factory setting default to 0 Remark 1 If away mode is turned on but without transferring 5 Binding PWD 5 Binding PWD Binding password er cades OOP raen delle the phone number the SMS will be replied Tran Tel1 Set NO TELEPHONE NUMBER 2 If the item is unsuccessfully setup the SMS will be To setup the menu you need to modify the menu details and then send the SMS to 401G module s replied FAIL phone number 6 3 Function menu setup Example 1 Send SMS to 401G module s phone number the user will get the replied Away Set 1 1 ON 0 To turn on away mode To setup 123456789 as 1st transfer SMS as below 2 Tran Tel1 Set 123456789 phone number 221 3 Tran Tel2 Set SMS Function commentary To setup digit 8 as unlock key 4 Unlock Key 8 0 9 1 Time Set 2011 11 11 11 11 11 Date Time Setup Format YYYY MM DD HH MM SS Modify system menu as right M 5 Binding PWD 2 PWD Set 8888 Admin password setup Admin password should be 4 digits Factory setting default to 8888 Operation Unlock time setup Co
12. uld be setup between 1 to 9 seconds Factory setting default to 3 3 Unlock Time 3 1S 9S de seconds Binding password The password will be automatically generated after the user bind the 4 Binding mobile phone number Modify the password is not allowed Remark Please change the admin password when you use it for the first time 6 4 System menu setup Send SMS to 4016 module s phone number the user will get the replied SMS as below SMS Function commentary 1 VIP UNLOCK EN 0 1 ON 0 OFF Turn on off VIP Unlock function 0 Turn off 1 Turn on Factory setting default to 0 2 VIP UNLOCK TEL1 Setup 1 VIP unlock phone number 3 VIP UNLOCK TEL2 Setup 2 VIP unlock phone number 4 VIP UNLOCK TEL3 Setup 3 VIP unlock phone number Binding password The password will be automatically generated after the user bind the S Binding mobile phone number Modify the password is not allowed VIP unlock function introduction When turn on VIP unlock function the pre setup VIP unlock phone number call 401G module s phone number the door will be unlocked automatically after DU The module is no needed to answer the call and the call is without any charge 10 For example 1 VIP UNLOCK 1 ON 0 OFF To turn on VIP unlock function 2 VIP UNLOCK TEL 1 123456789 To setup 1 VIP phone Number as 1234567
Download Pdf Manuals
Related Search