USER MANUAL - Kramer Electronics
Contents
1. SID X1 Defining the SID X1 Step in Commander 5 Connecting the SID X1 Switch off the power to all devices before connecting them to your SID X1 After connecting your SID X1 connect the power to other devices i To remote input To remote input To remote step in l moi switch and E selector switch LED indicator and LED To VP 81SID Computer Graphics Source Laptop sd Computer Graphics Computer Graphics DVD Player Kes E ue Figure 3 Connecting the SID X1 Step in Commander To connect the SID X1 andthe as illustrated in Figure 3 1 Connect up to four video sources HDMI DisplayPort DVI and PC graphics to the video input connectors Note If only one live input is connected the device automatically detects the live channel and activates it SID X1 Connecting the SID X1 5 1 2 Connect the unbalanced stereo audio source to the AUDIO IN 3 5mm mini jack connector 3 Connect the TP OUT RJ 45 connector to a compatible switcher for example VP 81SID 4 Optional Connect the REMOTE STEP IN 3 way terminal block to a contact closure switch and LED see Section 5 1 5 Optional Connect the REMOTE SELECT 3 way terminal block to a momentary contact closure switch and LEDs see Section 5 2 6 Optional Connect the LED ANODES 5 way terminal block to the remote input indicator LEDs see Section 5 3 7 Connect the power adapter to the SID X1 and to the mains power Note2. Warning Disconnect the power and unplug the unit from the wall before installing 2 1 Achieving the Best Performance To achieve the best performance e Use only good guality connection cables to avoid interference deterioration in signal guality due to poor matching and elevated noise levels often associated with low guality cables Do not secure the cables in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer SID X1 away from moisture excessive sunlight and dust 2 2 2 3 Getting Startec Shielded Twisted Pair Unshielded Twisted Pair Kramer engineers have developed special twisted pair cables to best match our digital twisted pair products the Kramer BC DGKat623 CAT 6 23 AWG cable and the Kramer BC DGKat7a23 CAT 7a 23 AWG cable These specially built cables significantly outperform regular CAT 6 and CAT 7a cables Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EAR
3. www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your questions comments and feedback Web site www kramerelectronics com KRAMER E mail info kramerel com SAFETY WARNING Disconnect the unit from the power supply before opening and servicing P N 2900 300754 Rev 5
4. 01 01 FF 15 01 03 80 34 20 78 EA B3 25 AC 51 30 B4 26 10 50 54 A5 4B 00 81 80 A9 40 71 4F 01 01 01 01 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28 55 00 07 44 21 00 00 1E 00 00 00 FF 00 35 30 35 2D 37 30 39 39 39 30 31 30 30 00 00 00 FC 00 53 49 44 2D 4D 55 4C 54 49 00 00 00 00 00 00 00 FD 00 38 4C 1E 53 11 00 0A 20 20 20 20 20 20 01 91 02 03 1B F1 48 10 05 84 03 02 07 16 01 23 09 07 07 65 03 0C 00 11 00 83 01 00 00 02 3A 80 18 71 38 2D 40 58 2C 45 00 07 44 21 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 25 00 07 44 21 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00 07 44 21 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 07 44 21 00 00 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 46 PC UXGA Monitor Model name SID X1 Manufacturer KRM Plug and Play ID KRM1200 Serial number 505 709990100 Manufacture date 2011 ISO week 255 EDID revision 1 3 Input signal type Analog 0 700 0 000 0 7V p p Sync input support Separate Composite Sync on green Display type RGB color Screen size 520 x 320 mm 24 0 in Power management Standby Suspend Active off sleep Extension blocs None DDC CI Color characteristics Default color space sRGB Display gamma 2 20 Red chromaticity Rx 0 674 Ry 0 319 SID X1 Default EDID a oO Green chromaticity Gx 0 188 Gy 0 706 Blue chromaticity Bx 0 148
5. 48 10 05 84 03 02 07 16 01 23 09 07 07 65 03 0C 00 11 00 83 01 00 00 02 34 80 18 71 38 2D 40 58 2C 45 00 07 44 21 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 25 00 07 44 21 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00 07 44 21 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 07 44 21 00 00 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 46 SID X1 Default EDID LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures
6. All LED supplies include a current limiting resistor and are designed to work with any standard LED Connecting the Remote Step In Switch and LED You can connect a remote contact closure step in switch to take control of the input of the attached switcher as well as a remote step in LED to the REMOTE STEP IN terminal block on the rear panel of the SID X1 Figure 4 illustrates the connections from the terminal block to the switch and LED REMOTE STEP IN Q r 15 Figure 4 REMOTE STEP IN Switch and LED Wiring To connect a remote step in switch and LED as illustrated in the example in Figure 4 1 Connect pins 2 and 3 from the terminal block to the remote step in switch 2 Connect pin 1 from the terminal block to the anode of the remote step in LED 3 Connect pin 3 from the terminal block to the cathode of the remote step in LED 5 2 Connecting the Remote Select Switch and LED You can connect a remote contact closure input selection switch to activate an input momentary contact is sufficient to switch inputs as well as an indicator LED to the terminal block on the rear panel of the SID X1 Figure 5 illustrates the connections from the terminal block to the switch and LED REMOTE SELECT ai G r 15 Figure 5 REMOTE SELECT Switch and LED Wiring To connect a remote selection switch and LED as illustrated in the example in Figure 5 1 Connect pins 2 and 3 from the terminal block to the remote selection s
7. By 0 064 White point default Wx 0 313 Wy 0 329 Additional descriptors None Timing characteristics Horizontal scan range 30 83kHz Vertical scan range 56 76Hz Video bandwidth 170MHz CVT standard Not supported GTF standard Not supported Additional descriptors None Preferred timing Yes Native preferred timing 1280x720p at 60Hz 16 10 Modeline 1280x720 74 250 1280 1390 1430 1650 720 725 730 750 hsync vsync Standard timings supported 720 x 400p at 70Hz IBM VGA 640 x 480p at 60Hz IBM VGA 640 x 480p at 75Hz VESA 800 x 600p at 60Hz VESA 800 x 600p at 75Hz VESA 1024 x 768p at 60Hz VESA 1024 x 768p at 75Hz VESA 1280 x 1024p at 75Hz VESA 1280 x 1024p at 60Hz VESA STD 1600 x 1200p at 60Hz VESA STD 1152 x 864p at 75Hz VESA STD EIA CEA 861 Information Revision number IT underscan Basic audio Supported YCbCr 4 4 4 Supported YCbCr 4 2 2 Supported Native formats 1 Detailed timing 1 1920x1080p at 60Hz 16 10 Modeline Detailed timing 2 Modeline vsync Detailed timing 3 1280x720p at 60Hz 16 10 1920x1080i at 60Hz 16 10 Modeline 1280x720 74 250 1280 1390 1430 1650 720 725 730 750 hsync vsync Detailed timing 4 720x480p at 60Hz 16 10 Modeline Re rte 720x480 27 000 720 736 798 858 480 489 495 525 hsync vsync CE video identifiers VICs timing formats suppo
8. activate the input of the switcher to which the SID X1 is connected press the STEP IN button If the switcher grants the SID X1 access to the input the STEP IN button lights If the switcher does not grant access for some reason the button flashes for a few seconds and then does not light This may be because the switcher input connected to the SID X1 has been set to have a lower priority than the currently active input Note Input priority on the switcher is set using the Kramer Control Software Audio Stream Priority By default see Section 5 4 an audio source connected to the 3 5mm mini jack Audio Input takes priority over any other audio stream This means that if there is a cable connected to the 3 5mm mini jack even without a live signal and the HDMI and DVI streams contain audio only the audio source from the 3 5mm audio jack is transmitted over the TP to the switcher 7 Wiring the Twisted Pair RJ 45 Connectors When using STP cable connect solder the cable shield to the RJ 45 connector shield Figure 8 defines the TP pinout using a straight pin to pin cable with RJ 45 connectors EIA TIA 568B Figure 8 TP Pinout Wiring PIN Wire Color Orange White Orange Green White Blue Blue White Green Brown White Brown a Pair1 4and5 Pair 2 1 and 2 Pair 3 3 and 6 INI OD a AJ wl rm gt 15342018 Warning Using a TP cable that is incorrectly wired
9. hsync vsync Detailed timing 2 1920x1080i at 60Hz 16 10 4 SID X1 Default EDID l 9 2 Modeline 1920x1080 74 250 1920 2008 2052 2200 1080 1084 1094 1124 interlace hsync vsync Detailed timing 3 1280x720p at 60Hz 16 10 Modeline 1280x720 74 250 1280 1390 1430 1650 720 725 730 750 hsync vsync Detailed timing 720x480p at 60Hz 16 10 Modeline 720x480 27 000 720 736 798 858 480 489 495 525 hsync vsync CE video identifiers VICs timing formats supported 1920 x 1080p at 60Hz HDTV 16 9 1 1 1920 x 1080i at 60Hz HDTV 16 9 1 1 1280 x 720p at 60Hz HDTV 16 9 1 1 Native 720 x 480p at 60Hz EDTV 16 9 32 27 720 x 480p at 60Hz EDTV 4 3 8 9 720 x 480i at 60Hz Doublescan 16 9 32 27 720 x 576i at 50Hz Doublescan 16 9 64 45 640 x 480p at 60Hz Default 4 3 1 1 NB NTSC refresh rate Hz 1000 1001 CE audio data formats supported LPCM 2 channel 16 20 24 bit depths at 32 44 48 kHz CE vendor specific data VSDB IEEE registration number 0x000C03 CEC physical address 1 1 0 0 Maximum TMDS clock 165MHz CE speaker allocation data Channel configuration 2 0 Front left right Yes Front LFE No Front center No Rear left right No Rear center No Front left right center No Rear left right center No Rear LFE No Raw data 00 FF FF FF FF FF FF 00 2E 4D 00 12 01 01
10. 0 mm 24 0 in Power management Standby Suspend Active off sleep Extension blocs CEA EXT DDC CI n a Color characteristics Default color space Non sRGB Display gamma 2 20 Red chromaticity Rx 0 674 Ry 0 319 Green chromaticity Gx 0 188 Gy 0 706 Blue chromaticity Bx 0 148 By 0 064 White point default Wx 0 313 Wy 0 329 Additional descriptors None Timing characteristics Horizontal scan range 30 83kHz Vertical scan range 56 76Hz Video bandwidth 170MHz CVT standard Not supported GTF standard Not supported Additional descriptors None Preferred timing Yes Native preferred timing 1280x720p at 60Hz 16 10 Modeline 1280x720 74 250 1280 1390 1430 1650 720 725 730 750 hsync vsync Standard timings supported 720 x 400p at 70Hz IBM VGA 640 x 480p at 60Hz IBM VGA 640 x 480p at 75Hz VESA 800 x 600p at 60Hz VESA 800 x 600p at 75Hz VESA 1024 x 768p at 60Hz VESA 1024 x 768p at 75Hz VESA 1280 x 1024p at 75Hz VESA 1280 x 1024p at 60Hz VESA STD 1600 x 1200p at 60Hz VESA STD 1152 x 864p at 75Hz VESA STD EIA CEA 861 Information Revision number IT underscan Supported Basic audio Supported YCbCr 4 4 4 Supported YCbCr 4 2 2 Supported Native formats Detailed timing 1 1920x1080p at 60Hz 16 10 Modeline 1920x1080 148 500 1920 2008 2052 2200 1080 1084 1089 1125
11. DVI source 8 PC UXGA LED Lights green when the PC UXGA input is selected PC UXGA 15 pin HD Connect to a PC graphics source Connector F 10 INPUT SELECT Button Press repeatedly to cycle and select one of the inputs to switch to the output 11 STEP IN Button Press to activate the input on the switcher that the SID X1 is connected to ON LED Lights green when the device is powered on SID X Defining the SID X1 Step in Commander Figure 2 defines the rear panel of the SID X1 REMOTE SELECT 5 S 125 2 EEE EJL Lop LEDANODES Figure 2 SID X1 Step in Commander Rear Panel Feature Function 1 TP OUT RJ 45 Connector Connect to a compatible switcher for example VP 81SID using CAT 6 or higher specification cable REMOTE STEP IN 3 way Connect to the remote contact closure step in switch and LED Terminal Block see Section 5 1 REMOTE SELECT 3 way Connect to the remote contact closure input selection switch and Terminal Block LED see Section 5 2 GND LED ANODES Note All LED supplies include a current limiting resistor and are 5 way Terminal Block designed to work with any standard LED OPTION DIP switches DIP switch 1 2 audio mode selection See Section 5 4 DIP switch 3 no function DIP switch 4 EDID lock See Section 5 4 6 12V DC Power Connector Connect to supplied power adapter center pin positive j HDMI DP DVI UXGA Connect to the remote input indicator LEDs see Section 5 3
12. KRAMER ELECTRONICS LTD USER MANUAL MODELS SID X 1 Step in Commander P N 2900 300754 Rev 5 SID X1 Step in Commander Quick Start Guide This guide helps you install and use your product for the first time For more detailed information go to http www kramerelectronics com support product downloads asp to LA download the latest manual or scan the QR code on the left Step 1 Check what s in the box 2 SID X1 Step in Commander 2 4 Rubber feet a 2 1 Power adapter 12V DC output A Quick Start Guide Step 2 Install the SID X1 Mount the device in a rack using the optional RK T2B rack adapter available for purchase or attach the rubber feet and place it on a shelf Step 3 Connect the inputs and outputs Always switch off the power to all devices before connecting them to your SID X1 Computer Laptop Front Panel Rear Panel EIA TIA 568B 12457836 se 2 Twisted Pair Pinout HDMI DISPLAYPORT O O ete Step in Commander Optional Lock the current EDID if required Step 5 Connect the power 4 Connectthe poweradapter tothe SID X1 and plug the adapter into the mains electricity Note Operationis fully automatic no manual adjustmentis needed Contents Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Shielded Twisted Pair Unshielded Twisted Pair 2 3 Recyclin
13. L OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at
14. N facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at http Avww kramerelectronics com support recycling Overview The SID X1 accepts an HDMI DisplayPort DVI and PC graphics video input as well as an unbalanced stereo audio input which is embedded into the output signal and transmits the signal via TP Twisted Pair cable to a compatible switcher for example the VP 81SID When the SID X1 is connected to a switcher it also controls the input and output selection of the switcher In particular the SID X1 e Supports DDC Display Data Channel communication between the selected input and output on 15 pin HD connector pins 12 and 15 e Supports HDMI with Deep Color x v Color and 3D e Is HDCP compliant works with sources that support HDCP repeater mode e Can be installed up to 50m 164ft from the switcher Features automatic live input detection when connected to a single input e Lockable EDID You can control the SID X1 using the front panel buttons or remotely via contact closure switches 4 Defining the SID X1 Step in Commander Figure 1 defines the front panel of the SID X1 ON SELECT O LILI Step In Commander SID X1 INPUT STEP IN Figure 1 SID X1 Step in Commander Front Panel Feature Function 4 DisplayPotLED Lights green when the DisplayPort input is selected DisplayPor Connector DVI Connector Connect to a
15. cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics willdo Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as
16. der this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORA
17. g Kramer Products 3 Overview 4 Defining the SID X1 Step in Commander 5 Connecting the SID X1 5 1 Connecting the Remote Step In Switch and LED 5 2 Connecting the Remote Select Switch and LED 5 3 Connecting the Remote Input Selection LEDs 5 4 Audio Mode Selection 5 5 Locking the EDID 6 Operating the SID X1 6 1 Selecting an Input 6 2 Taking Control of the Switcher Input 6 3 Audio Stream Priority 7 Wiring the Twisted Pair RJ 45 Connectors 8 Technical Specifications 9 Default EDID 9 1 HDMI DisplayPort and DVI 9 2 PC UXGA Figures Figure 1 SID X1 Step in Commander Front Panel Figure 2 SID X1 Step in Commander Rear Panel Figure 3 Connecting the SID X1 Step in Commander Figure 4 REMOTE STEP IN Switch and LED Wiring Figure 5 REMOTE SELECT Switch and LED Wiring Figure 6 Remote Input Indicator LED Wiring Figure 7 Example Remote Input Indicator LED Wiring for the DVI Input Figure 8 TP Pinout Wiring COON O1 BR OONN O OSI O VI 10 13 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront video audio presentation and broadcasting professionals on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function GROUP 1 Distributi
18. nected to the 3 5mm Auto Manual mini jack the analog external audio is transmitted If not Audio Mode the embedded audio is transmitted Manual DisplayPort and HDMI ports always transmit the embedded audio and the VGA always transmits the analog audio The DVI port audio is defined by DIP switch 2 2 Off default Only the DVI uses the embedded audio DVI Audio On Only the DVI uses the analog external audio Source Locking the EDID To prevent the stored EDID either default or read from a device from being overwritten set DIP switch 4 to ON Note The device must be power cycled after you change DIP switch 4 Connecting the SID X 11 6 1 6 2 6 3 Operating the SID X1 Powering up the SID X1 recalls the last settings that is the configuration of the device when it was powered down from the non volatile memory The SID X1 inputs can be selected remotely via the VP 81SID For details on operating the SID X1 remotely via the VP 81SID see the VP 81SID User Manual Selecting an Input To select an input press the INPUT SELECT button repeatedly until the required input is active as indicated by the associated LED Note If only one live input is connected the device automatically detects the live port and activates it If more than one input is connected you must select the required input by pressing the INPUT SELECT button until the associated LED lights Taking Control of the Switcher Input To
19. on Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Video Products Thank you for purchasing the Kramer TOOLS SID X1 Step in Commander and which are ideal for Display systems requiring simple input selection Remote monitoring of computer activity in schools and businesses Rental staging applications Multimedia and presentation source selection Each package includes the following items e SID X1 Sfep in Commander e Power adapter 12V DC output e This user manual Download up to date Kramer user manuals from http www kramerelectronics com troductior 2 Getting Started We recommend that you e Unpack the eguipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual e Use Kramer high performance high resolution cables user manuals application programs and to check if firmware upgrades are available where appropriate Caution No operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adapter that is provided with the unit Go to http www kramerelectronics com to check for up to date
20. rted 1920 x 1080p at 60Hz HDTV 16 9 1 1 1920 x 1080i at 60Hz HDTV 16 9 1 1 1280 x 720p at 60Hz HDTV 16 9 1 1 Native 720 x 480p at 60Hz EDTV 16 9 32 27 720 x 480p at 60Hz EDTV 4 3 8 9 720 x 480i at 60Hz Doublescan 16 9 32 27 720 x 576i at 50Hz Doublescan 16 9 64 45 640 x 480p at 60Hz Default 4 3 1 1 NB NTSC refresh rate Hz 1000 1001 CE audio data formats supported LPCM 2 channel 16 20 24 bit depths at 32 44 48 kHz CE vendor specific data VSDB IEEE registration number 0x000C03 CEC physical address 1 1 0 0 Maximum TMDS clock 165MHz CE speaker allocation data Channel configuration 2 0 Front left right Yes Front LFE No Front center No Rear left right No Default EDID 1920x1080 148 500 1920 2008 2052 2200 1080 1084 1089 1125 hsync vsync PAPERS 1920x1080 74 250 1920 2008 2052 2200 1080 1084 1094 1124 interlace hsync Rear center No Front left right center No Rear left right center No Rear LFE No Raw data 00 FF FF FF FF FF FF 00 2E 4D 00 12 01 01 01 01 FF 15 01 03 6E 34 20 78 EE B3 25 AC 51 30 B4 26 10 50 54 A5 4B 00 81 80 A9 40 71 4F 01 01 01 01 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28 55 00 07 44 21 00 00 1E 00 00 00 FF 00 35 30 35 2D 37 30 39 39 39 30 31 30 30 00 00 00 FC 00 53 49 44 2D 4D 55 4C 54 49 00 00 00 00 00 00 00 FD 00 38 4C 1E 53 11 00 0A 20 20 20 20 20 20 00 A0 02 03 1B F1
21. the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy un
22. will cause permanent damage to the device SID X1 Wiring the Twisted Pair RJ 45 Connectors EI 8 Technical Specifications INPUTS Video 1 HDMI on an HDMI connector 1 DP on a DisplayPort connector 1 DVI D on a DVI I connector 1 VGA on a 15 pin HD F connector 1 Unbalanced stereo audio on a 3 5mm mini jack OUTPUTS 1 TP on an RJ 45 STANDARDS HDMI with Deep Color x v Color and 3D HDCP Works with sources that support HDCP repeater mode MAXIMUM 50m 164 ft up to 1080p 60Hz STEP IN DISTANCE POWER 12V DC 800mA CONSUMPTION OPERATING 0 to 40 C 32 to 104 F TEMPERATURE STORAGE 40 to 70 C 40 to 158 F TEMPERATURE HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 18 8cm x 11 3cm x 2 5cm 7 4 x 4 5 x 1 W D H rack mountable WEIGHT 0 48kg 1 11bs approx ACCESSORIES Power adapter OPTIONS 19 Rack adapter RK T2B RTBUS 12 RTBUS 22 SID X1BP Kit substitute black top plate for the SID X1 to blend in with the color of the modular TBUS 10xl 9 Default EDID Each input on the SID X1 is loaded with a factory default EDID 9 1 HDMI DisplayPort and DVI Monitor Model name SID X1 Manufacturer KRM Plug and Play ID Serial number Manufacture date KRM1200 505 709990100 2011 ISO week 255 7 13 Digital Color bit depth Undefined Display type RGB color Screen size 520 x 32
23. witch 2 Connect pin 1 from the terminal block to the anode of the remote selection LED 3 Connect pin 3 from the terminal block to the cathode of the remote selection LED 5 3 Connecting the Remote Input Selection LEDs You can connect remote input selection LEDS to the LED terminal block on the rear panel of the SID X1 to indicate which is the active input Figure 6 illustrates the connections from the terminal block to the LEDs dH 1 FLAT 5 LED ANODES Figure 6 Remote Input Indicator LED Wiring To connect remote input indicator LEDs 1 Connect pin 1 from the terminal block to the anode of the remote HDMI indicator LED 2 Connect pin 2 from the terminal block to the anode of the remote DP indicator LED 3 Connect pin 3 from the terminal block to the anode of the remote DVI indicator LED see the example in Figure 7 4 Connect pin 4 from the terminal block to the anode of the remote UXGA indicator LED 5 Connect pin 5 from the terminal block to the cathodes of each LED Figure 7 Example Remote Input Indicator LED Wiring for the DVI Input ek SID X Connecting the SID X1 5 4 5 5 Audio Mode Selection The Option DIP switches 1 and 2 see Section 6 3 control the manner in which audio is handled Note DIP switch 1 must be set to ON to enable DIP switch 2 to control the audio mode selection DIP switch State Function 1 Off default Automatic if an audio source is con
Download Pdf Manuals
Related Search