F11 User Manual V1.0
Contents
1. and card enrolled 15 F11 User Manual V1 0 3 1 3 Delete a Single User The operation steps for single user deletion 1 In verification state swipe your management card for five consecutive times to enter the single user deletion state Swipe your management card one more time to return to the verification state The red LED blinks twice every three second the speaker play two short beep every three seconds 2 The user press the finger or swipe the card 1 Press your finger onto the sensor to delete a user Press one of your enrolled fingers properly onto the sensor If the verification succeeds the green LED is solid on for one second the speaker play one long beep Deletion is successful and automatically return to the deletion state If the verification fails the red LED is solid on for one second the speaker play one long beep Deletion is failed and automatically return to the deletion state 2 Swipe your card over the reader to delete a user Swipe a registered card over the reader If the verification succeeds the green LED is solid on for one second the speaker play one long beep Deletion is successful and automatically return to the deletion state If the verification fails the red LED is solid on for one second the speaker play one long beep Deletion is failed and automatically return to the deletion state 3 If you swipe your management card one more time or your o2. Adapter O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T11363 2006 x Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this part is above the limit requirement in SJ T11363 2006 Note 80 of the parts in this product are manufactured with non hazardous environment friendly materials The hazardous substances or elements contained cannot be replaced with environment friendly materials at present due to technical or economical constraints 24
3. 1 User Manual V1 0 WA Tip The system returns to the verification state if any operation in step 3 is timeout and only prompts you to enroll the management card again after you restart the device again The management card enrollment procedure is shown below System power on Swipe a new card Red LED is solid on for 1s 1 long beep every 3s anagement carq exist Enroll a management card No Yes Verification state 3 1 2 Enroll an Ordinary User The mode for you to enter the Verify users Press your finger or swipe your card No beep red LED blinks once every 2s Enroll successful Returns to verification state Green LED is solid on for 1s 1 long beep enrollment state using the 10 3 Device Operations management card is known as the management card enrollment mode In this mode you can only enroll one user every time you enter enrollment state When you enroll a new user the system automatically assigns a minimum idle ID to the user Each user is allowed to enroll 10 fingerprints and one ID card at most When the fingerprint and ID card enroll completely or operation timeout or swipe the management card the system return to verification State To enroll a user proceed as follows 1 In the verification state the system goes into the ordinary user enrollment state after you swipe a management
4. F11 User Manual Version 1 0 Date Jul 2010 Introduction This document mainly introduces the user s operation of F11 About the device installation please refer to F11 Installation Guide F11 User Manual V1 0 Notational Conventions This document includes such notational conventions as tips important notices and precautions The notations contained in this manual include Indicates important information including precautions which must be read carefully to achieve the optimal equipment performance Table of Contents Table of Contents le OPERATION INSTRUCTION sc ctacle aca aculetd sata tenlandch a haa tentecde adalat l Wed emer Place me It ea a tense ee eee l 1 2 Instruction for Card Using 00n0n00n00000000eeeeeeeeeeeetenreereeeeereeee 2 Ih Phe CALM ONS ner e E A 2 Ze DEVYTCEZTNI RODUG FTON meta ah iat elas Ske A A A AA E 4 2A Overview of Device FUNCTIONS seerrnad ins nA 4 2D Product Appear o niora R 5 DD Nera ON A Ea a eeu ere eae tew eee uur ueereaee 7 2 4 M nagement Card ennenannn unnan ONEONE AN 7 AI OVSENI PASS WON eeen sem eat enbe eee eat Oabe eam eat anbee tes 8 2 6 Operation TimeOut ecirar deduceeticdvess dedecestccceanscdees 8 ae SUI yo OT eel ING Se coe ert ce Se aan ce Sie er ret ce Se arin Sie aerate teed 9 3 bManasement Card ics 1 2 ccsccrescesedececesedeeecstedetecssedeesassadstenesedeesassees 9 3 1 1 Enroll a Management Card ceric ccc ecru ee terete ceceees 9 3 1 2 Enroll a
5. Fingerprint verification Press your finger on the fingerprint sensor in a proper way If the verification succeeds the green LED is solid on for one second the speaker play two short beep If the verification fails the red LED is solid on for one second the speaker play two short beep 2 Card verification Swipe your card over the card reader If the verification succeeds the green LED is solid on for one second the speaker play two short beep If the verification fails the red LED is solid on for one second the speaker play two short beep 18 3 Device Operations The user verification procedure is show as below Verification state No beep green LED blinks once every 2s start to verify Door sensor or tamper switch exceptional Y Card verification FP verification Yes Alarm FP erification successful ard verification successful Red LED is solid on for ls 2 short beeps Eo a verification failure Red LED is solid on y for We 2 short beeps verification Green LED is solid on for failure Lock ls 2 short beeps verification success Verification state 7A Tip the administrator bearing a management card can only unlock using his fingerprint previously enrolled 19 F11 User Manual V1 0 3 3 T
6. Your fingerprint s enrolled in this step will overwrite all your previous fingerprints c If you swipe a new card or press a finger three times that is not enrolled before and succeeds in enrollment the green LED is solid on for one second the speaker play one long beep and you can continue enrolling new fingerprints and card d The system automatically returns to the verification state when both 10 fingerprints and ID card are enrolled the management card is swiped once or operation times out 14 3 Device Operations The flow chart is shown below Green LED blinks twice every 3s 2 short beeps every 3s start to enroll Swipe management card Red LED is solid on for Is 1 long beep enrollment failure Green LED is solid on enrollment success em Enrollment state Red LED is solid on for ls 1 long beep enrollment failure Press finger or Sui OGEte Verification state User enrollment successful ew fingerprint or card Swipe card me pe Press finger Green LED is solid on for Is 1 long beep enrollment success Card enrollment successful FP enrollment successful Yes Enrollment is successful Red LED is solid on for Is 1 long beep enrollment failure 1 long beep 10 fingerprints Verification state
7. above Fingerprint Sensor Used to enroll and match fingerprints and delete user Power Button Press and hold the power button for three seconds to turn the power off press and hold the power button one second to turn it on Bottom view Speaker Reset Button Reset Button Used to restart the device Speaker Used to play the beep sound for details please refer to LED Indicator introduction Rear view lt pn i Wiring Terminal Tamper Switch 2 Device Introduction Wiring Terminal Connects with locks and power supply through cables For details please refer to F11 Installation Guide Tamper Switch Used to generate a tamper alarm For details see 3 3 Tamper Switch 2 3 Verification State Verification state After the device is powered on the device enters the verification state if you have enrolled or successfully enrolls a management card or in the event of timeout of any operation In the verification state all users are allowed to verify their identity and unlock the door The administrator bearing a management card can only unlock using his fingerprint previously enrolled The administrator can perform such operations as user enrollment and deletion 2 4 Management Card The enrolled users are classified into administrators and ordinary Users Administrators An administrator is allowed to perform all operations including user enrollment and deletion De
8. amper Switch The tamper switch is pressed and held down with the rear cover When the device is dismantled the tamper switch will be lifted up and then it will send an signal to trigger an alarm Clear alarm The user can clear the alarm by unlocking the door upon successful verification Restore factory defaults The factory defaults can be restored through the tamper switch When the system generates an alarm for 30 60 seconds the user can press the tamper switch three times Till the speaker sounds to restore default settings including the device number system password IP address 485 address and keyboard password Pa Tip The user information stored on device will be cleared after the device is restored to factory defaults please be cautious 20 4 Appendix 4 Appendix 4 1 List of Parameters The following table lists the basic functional parameters of the device Power Supply 12V 3A Alarm Door lock Door switch Function One Wiegand output 10000 fingerprint and ID card Record capacity 100000 pieces of records Enrollment capacity 1500 fingerprints 10000 cards fingerprint card ID Mifare card fingerprint TCP IP RS485 RS232 Beep prompt LED Bi color indication red green 21 4 Appendix 4 2 Statement on Human Rights and Privacy Dear Customers Thank you for choosing the multi biometric products designed and manufactured by us As a world renowned provider of biometric te
9. card once In the enrollment state swiping a management card once will return to the verification state In this state you can also enroll the fingerprint for the old user 2 The system will automatically assign a smallest idle ID for the new user The green LED blinks twice every three seconds at the same time the speaker play two short beep every three seconds You can start user enrollment There are the following two cases 1 Swipe ID card first a When you swipe your new ID card and succeed in enrolling a user the green LED is solid on for one second the speaker play one long beep and you can proceed to step b If user enrollment fails the red LED is solid on for one second the speaker play one long beep and returns to the enrollment state waiting for you to press your finger or swipe your card b The system enters the specified fingerprint enrollment state Press the same finger over the sensor three times following the light and 11 F11 User Manual V1 0 beep prompts The green LED blinks twice every three seconds and the speaker play two short beep c If fingerprint enrollment succeeds the green LED is solid on for one second the speaker play one long beep and you can continue the proceed to step b If fingerprint enrollment fails the red LED is solid on for one second and the speaker play one long beep and repeats step b d The system automatically returns to the verification state when both 10 finge
10. chnologies and services we pay much attention to the compliance with the laws related to human rights and privacy in every country while constantly performing research and development We hereby make the following statements 1 All of our fingerprint recognition devices for civil use only collect the characteristic points of fingerprints instead of the fingerprint images and therefore no privacy issues are involved 2 The characteristic points of fingerprints collected by our products cannot be used to restore the original fingerprint images and therefore no privacy issues are involved 3 We as the equipment provider shall not be held legally accountable directly or indirectly for any consequences arising due to the use of our products 4 For any dispute involving the human rights or privacy when using our products please contact your employer directly Our fingerprint products or development tools for police use support the collection of the original fingerprint images As for whether such a type of fingerprint collection constitutes an infringement of your privacy please contact the government or the final equipment provider We as the original equipment manufacturer shall not be held legally accountable for any infringement arising thereof 22 4 Appendix Note The law of the People s Republic of China has the following regulations regarding the personal freedom 1 Unlawful arrest detention or search of c
11. itizens of the People s Republic of China is prohibited infringement of individual privacy is prohibited 2 The personal dignity of citizens of the People s Republic of China is inviolable 3 The home of citizens of the People s Republic of China is inviolable 4 The freedom and privacy of correspondence of citizens of the People s Republic of China are protected by law At last we stress once again that biometrics as an advanced recognition technology will be applied in a lot of sectors including e commerce banking insurance and legal affairs Every year people around the globe suffer from great loss due to the insecurity of passwords The fingerprint recognition actually provides adequate protection for your identity under a high security environment 23 4 Appendix 4 3 Environment Friendly Use Description The Environment Friendly Use Period EFUP marked on this product refers to the safety period of time in which the product is used under the conditions specified in the product instructions without leakage of noxious and harmful substances The EFUP of this product does not cover the consumable parts that need to be replaced on a regular basis such as batteries and so on The EFUP of batteries is 5 years Names and Concentration of Toxic and Hazardous Substances or Elements Toxic and Hazardous Substances or Elements Parts Name Chip resistor Chip capacitor Chip inductor Chip diode ESD components Buzzer
12. leting all the other users except himself The privileges of the device administrators are implemented through the management cards Ordinary users Ordinary users are only allowed to verify their identity and unlock A management card is a card specially allocated for a super administrator Each device must at least enroll one management card If no management card is enrolled you cannot perform any operation F11 User Manual V1 0 You can implement different functions by swiping a management card for different times in a row By swiping the management card once you can go into the single user enrollment state By swiping the management card five times in a row you can enter the single user deletion state Consecutive swipes Consecutive swipes mean the interval between two swipes in a row is less than 5 seconds The fingerprints of the user who bears a management card can only be enrolled through FP Reader software For details see the FP Reader Software User Manual Pa Tip Users who bear management cards can only verify their identity and unlock using their fingerprints previously enrolled 2 5 System Password A system password is a password used to enhance the security of device data in TCP IP RS485 RS232 communications WA Tip The system password can be modified through the FP Reader Software For details see the FP Reader Software User Manual 2 6 Operation Timeout The default operation timeout time i
13. n Ordinary USet ccc ccceceeeeeseesesseeesseeseeeeeees 10 Pl DIGIC tea SINC le Use wecirectcera tern ce cerectceratecnseerechieea tect atan 16 32 User Veria eitn O 18 D gt lamper OWE ena a E E EA 20 ANPP ENDL eriari ntie LEE ans ee tanks R a 21 Vk Ue STS 2 lr 2 12 1 Bc pea OR a ec tre re TOUR CUT rE OS 21 4 2 Statement on Human Rights and Privacy cecesseeeeeeeeees 22 4 3 Environment Friendly Use Description c sseeeeeeeeeees 24 1 Operation Instruction 1 Operation Instruction 1 1 Finger Placement Enroll fingerprint by pressing index finger middle finger or ring finger thumb and little finger are clumsy 1 Proper press Make finger center pressed on the sensor window 2 Improper press Upright Too lean Too low Please adopt the correct way to place the finger to avoid improper operation led to the identification performance degradation F11 User Manual V1 0 1 2 Instruction for Card Using Integrated with a non contact RF card reader module this device supports the ID cards and MIFARE cards Optional and only used as ID cards By offering multiple verification modes such as FP verification and RF and card verification this device can accommodate to diversified user needs Swipe your card across the sensor area following the light and beep prompts and remove your card after the device has sensed it For the card sensor area please
14. nagement card you can perform such functions as offline enrollment deletion of users The light and beep prompts will guide you through all the operations without screen display or keyboard Featuring a compact and simple design this device allows users to connect several devices through a PC and supports several communication modes Alarm Door Lock 2 Device Introduction 2 2 Product Appearance Front view e Power Button LED Indicator LED indicator The LED indicator is used to display device operation results and exceptional statuses which are defined as follows Operation succeed The green indicator is solid on for one second at the same time the speaker play one long beep Operation failed The red indicator is solid on for one second at the same time the speaker play two short beep Enrollment of administrator The red LED blinks once every three seconds at the same time the speaker play one long beep Enrollment of user The green LED blinks twice every three second at the same time the speaker play two short beep every three seconds Single user deletion The red LED blinks twice every three seconds at the same time the speaker play two short beep Fingerprint Sensor Card Sensor Area F11 User Manual V1 0 Verification state The green LED blinks once every two second the beeper with no sound Card Sensor Area Refers to the area in the white dashed line round as shown in the figure
15. peration times out the system will return to the verification state Pa Tip In single user deletion mode management card users cannot be deleted because swiping the management card will return the system to the verification state 16 3 Device Operations Single User Deletion Procedure Verification state ma Enter the deletion state after swiping the management card 5 times in a row No registered user The system returns to verification state Red LED blinks twice every 3s 2 short beep every 3s start to enroll Y Y Fingerprint verification Card verification Is FP verification successful s card verification successful Red LED is solid on ii for 1s one long beep deletion failure Red LED is solid on for 1s one long beep deletion failure Y Delete user success roy Verification state Red LED is solid on for 1s one long beep deletion success ry F11 User Manual V1 0 Pa Tip Please be cautious to do this operation the deleted data can not be recovered 3 2 User Verification Operation steps 1 When the device is in verification state the green LED blink once every two second to prompt verification 2 Start user verification The device supports two verifications modes fingerprint verification and card verification 1
16. refer to 2 2 Product Appearance 1 3 Precautions Protect the device from exposure to direct sunlight or strong beam for the strong sunlight greatly affects the fingerprint collection and leads to fingerprint verification failure It is recommended to use the device under a temperature of 0 50 C so as to achieve the optimal performance In the event of exposure of the device to the outdoors for long periods of time it is recommended to adopt sunshade and heat dissipation facilities because excessively high or low temperature may slow down the device operation and result in high false rejection rate FRR and false acceptance rate FAR When installing the access control device please connect the power cable after all the other wiring If the device does not operate properly be sure to shut down the power supply before performing necessary inspection Be aware that any live line working may cause damage to the device and that damage is beyond the scope of our normal warranty 1 Operation Instruction For matters that are not covered in this document please refer to related materials including the Device Installation Guide FP Reader Software User Manual 2 Device Introduction 2 Device Introduction 2 1 Overview of Device Functions Our product can either control the electronic lock or connected with external alarm This device operation is simple and flexible and supports the use of management cards With a ma
17. rprints and ID card are enrolled the management card is swiped once or operation times out 2 Press finger first a Press the same finger over the sensor three times following the light and beep prompts The green LED blinks twice every three seconds at the same time the speaker play two short beep every three seconds by adopting the proper finger placement If fingerprint enrollment succeeds the green LED is solid on for one second the speaker play one long beep and you can proceed to step b If fingerprint enrollment fails the red LED 1s solid on for one second the speaker play one long beep and returns to the enrollment state waiting for your to press your finger or swipe your card b The system enters the specified user enrollment state continue the proceed to step a and waiting for you to swipe your new ID card or press your finger c The system automatically returns to the verification state when both 10 fingerprints and ID card are enrolled the management card is swiped once or operation times out 3 If you are already assigned with an ID then there are the following two cases for you to enroll your fingerprint s or card 1 Enroll fingerprint s when you have already enrolled card a In the state of enrollment state after you swipe the enrolled card the system enter the fingerprint enrollment state You can re enroll this 12 3 Device Operations user s fingerprint and the new fingerprint s will over
18. s 15 seconds When you enroll a management card enroll or delete a user the green LED will blink twice every three seconds at the same time the speaker play two short beep every three seconds if there is no operation After three times of indicator the device returns to verification state automatically Pa Tip You can set the timeout period through the FP Reader Software 3 Device Operations 3 Device Operations 3 1 Management Card 3 1 1 Enroll a Management Card To enroll a management card proceed as follows l The device automatically detects whether there exists a management card 2 If the device fails to detect the presence of a management card it enters the management card enrollment state The green LED blinks once every three seconds at the same time the speaker play one long beep every three seconds Pa Tip It is timeout after 15 seconds and return to verification state After management card enrolled you can use the FP Reader Software to set or modify the card number 3 Register the management card please swipe your card near to the card sensor area 4 If enrollment fails the red LED is solid on for one second at the same time the speaker play two short beep The system returns to step 3 and wait for user to swipe card 5 If enrollment succeed the green LED is solid on for one second at the same time the speaker play one long beep And system returns to verification state F1
19. write the previous fingerprints b Press the same finger over the sensor three times following the light and beep prompts by adopting the proper finger placement If fingerprint enrollment succeeds the green LED 1s solid on for one second the speaker play one long beep and gets ready for enrollment of next fingerprint c The system automatically returns to the verification state when both 10 fingerprints and ID card are enrolled the management card is swiped once or operation times out 7A Tips 1 The fingerprint s enrolled in this step will overwrite all your previously enrolled fingerprints Please swipe the card or press the finger one second after the light blinked 2 In this mode the fingerprint of the user who bears the management card cannot be enrolled because swiping the management card will return the system to the verification state automatically 2 Enroll card and fingerprint s when you have already enrolled fingerprint s a Press the finger with enrolled fingerprint three times following the light and beep prompts If you are identified as the same person in each of verification attempt the system enters the fingerprint enrollment state b The system starts to re enroll your fingerprint and ID card If the card is not enrolled when the green LED blinks twice every three seconds the speaker play two short beep every three seconds One 13 F11 User Manual V1 0 second after the light blinks
Download Pdf Manuals
Related Search