RST100 Quick Start Guide
Contents
1. www beamcommunications com a i a a www beamcommunications com2. To make and receive calls you may need to enter a PIN code Refer to manual for more information If any problems try the following Action required 1 Repeat these instructions to ensure everything has been completed RST100 Signal LED Handset tone Enter four digit SIM PIN and await a Connect antenna amp cable Flashing Red LED Fane change of tone up to 10 seconds 2 ls there power to the unit AOS then hang up i 1 Plug the antenna cable into the antenna jack located on the rear panel of the RST100 as shown twotonesof sg j j MEREN eee tee fuses equal length en successful the phone will register _ls the card active below Secure this cable by tightening the connector collar g and proceed wil aorndliise i l If not refer to your Service Provider 2 The specified cable being used must not exceed the Iridium 3dB maximum loss rating This will Flashing Red LED ee bee ie es code eae of 4 If the antenna signal is not strong you one up to ten seconds an ang up ensure maximum performance of your RST100 Refer to your Service Provider for full details or o high tone is ms P Ma a i M need to move pea to access longer than EN SUGCESTIU MIE PRONE WME etter coverage and re test to purchase an approved cable ee ls EEE ionialiiee g a ae st Constant LED Normal dial tone No action required For additional troubleshooting refer to see Iridium Antenna Guide or visit us at your manual or visit us
3. BEAM RS T100 Installation Options mo lt gt BEAM Hands free z Interface Microphone RST973 S Alert Buttons Indium Laaa amama Antenna Antenna Intelligent Handset Remote Satellite Terminal RST100 RS232 Data Connection i 110 240 V AC Cordless RJ 11 Phone RJ 11 PABX Integration 11 32 V DC Handsfree Kit Intelligent Handset More info www beamcomm net te 7 an Optimising Iridium performance Iridium is a line of sight Satellite network conditions that can compromise the quality of the service you may receive include 1 Obstructions Provide the best satellite view for your antenna by removing all obstructions where possible 2 Cabling Use the shortest cable length and the fewest number of connectors on all Iridium certified antenna cable runs 3 RF Interference Install antenna as far away from other transmitters as possible BEAM Thank you for purchasing the BEAM RST100 This Quick Start Guide lists the steps to install your BEAM Satellite equipment 1 Installing your SIM card 2 Mounting your RST100 3 Connect AC DC Power cord 4 Connect handset iHandset optional D5 Connect a Laptop PC 6 Connect an antenna amp cable 7 Power Up make receive calls Installing your SIM card Package Contents Before commencing installation ensure your package has the following components 1x RST100 unit 1x universal plug pack power adapter 110 240V AC 1
4. dure To end the call hang up the handset The Call LED light will then turn off as Ds Power LED flashes during self diagnosis then illuminates a steady green Vmail SMS LEDs flashes to indicate message s are waiting in your voice mailbox to be retrieved This service is subject to network support and not available from all providers Connect handset optional Connect a telephone handset answering machine or cordless phone into the Line or Accessory socket This socket supports a standard RJ11 plug Facsimile Messaging via a standard RJ11 connection is not supported on the Iridium Network see your Service Provider to discuss the dedicated FX2600 Iridium Fax Unit or visit us at www beamcommunications com Connect Intelligent handset optional Connect to the Iridium Intelligent Handset if supplied directly to the Handset socket of the RST 100 Only use the extension cables for this handset provided Cables up to 30 metres in length are available from your Service Provider Call LED Varies with status of call which can be In Call Waiting to connect or Incoming call Signal LED indicates strength of Iridium signal at your location RED no signal PIN code required ORANGE low signal Connect a Laptop PC GREEN Good signal Plug the serial cable into the Comm Port of the RST100 Front of RST100 NOTE If no serial port is available try using a i EE USB Serial connector not supplied PIN Codes
5. the event of future service C Locate mounting holes D Screw bracket to RST100 Setting up your BEAM RST100 Remote Terminal Handset Line iHandset COMM port To successfully make a call on the Iridium network you need Antenna Power Remote LOG port 1 Dial tone on the telephone handset 2 Call LED must shine green or orange continuously Connect the AC DC Power With LIVE power turned OFF connect power Jack to rear of RST 100 Continue to make your phone call as you normally use a traditional phone noting any dialling prefix instructions secure cable by tightening collar advised by your service provider Powering Up amp Making a Call When all previous 1 6 steps have been completed confirm that the antenna is connected and the power loom active Once power is connected allow up to 3 mins for the LEDs to register with network Rear of RST100 Once you have entered the phone number you will hear progress pips from the Iridium network It can take up CAUTION to 30 seconds for the Iridium network to connect a call so a pause at this stage Is not unusual DO NOT connect LIVE power to the battery until installation is complete You will shortly hear the called party end ringing or hear a busy tone and voice message indicating why your call was not possible When the other party answers the Call LED will change from steady orange to flashing orange Indicating call in progress This is a normal operating proce
6. x DC Power Cable for use only on 11 32V DC input 1 x 9 pin to 9 pin RS 232 cable Male to Female 1 x User Manual printed 1 x Iridium Antenna Guide printed Allen Key screws amp washers amp Mounting Brackets 1x Documentation CD also at www beamcommunications com Tools required 1 Philips head screwdriver 2 Allen Key supplied Follow the instructions below p Unscrew with 2mm Allen Key 9 Slide the top black clip back towards you 6 Flick this clip up to expose the rails to slide the SIM into 7 8 Gently push down on the grey SIM housing and push away from you to LOCK the SIM in place Replace covers by following steps 4 to 1 NOTE Metallic SIM contacts must be face down to engage with the SIM card reader Mounting your RST100 The RST100 comes with two 2 right angle brackets that allow mounting for mobile and fixed positioning Carefully slide the RST100 between the two mounting brackets and secure with the retaining screws Note To ensure a secure installation 1 Mount the RST100 on a clean even surface 2 Clean the mount surface of the RST100 3 Use the correct type of screws as supplied 4 If mounting on wood ensure wood is structurally sound 5 Leave enough room around the RST100 to allow easy access to the rear panel B Flush mount Do not install the unit in a permanently concealed area Access must be possible in
Download Pdf Manuals
Related Search