Belling Cooker Hood User Manual
Contents
1. Activated carbon filter can be used to trap odours In order to install the activated carbon filter the grease filter should be detached first Press the lock and pull it downward 1 Installation Plug the activated carbon filter into the unit and turn it in clockwise direction Repeat the same on the other side NOTE o Make sure the filter is securely locked Otherwise it would loosen and cause dangerous When activated carbon filter attached the suction power will be lower Remove all blue protective film on chimney and cooker hood the installation is now finished 12 Technical Data Electricity supply 230 240V 50Hz Classification class I Noise level External Venting Position 3 54 dBA Position 2 47 dBA Position 1 40 dBA Light bulbs 2 x 1 5W LED Please make sure you follow the instructions for replacing light bulbs carefully and always make sure you use the correct bulb type Motor rating 100W Carbon filters x 2 available as Spares Grease filters x 3 aluminium panel Note After cleaning grease filters may lose their colour slightly this does not affect their performance Extraction Rate External Position 3 527m3 H Position 2 440m3 H Position 1 370m3 H 13 Belling Customer Care Please keep this handbook in a safe place Please fill in the model number and serial number in the spaces provided below as they will assist us should you need to call 082. 44 815 3746 When you dial this number you will hear a recorded message and be given a number of options This indicates that your call has been accepted and is being held in a queue Calls are answered in strict rotation as our Customer Care Representatives become available Enter appliance numbers here for future reference Model No ee ed Serial No pt PE tT These numbers can be found on your appliances Outside the UK and Northern Ireland refer to your local supplier ellin Stoney Lane Prescot Merseyside L35 2XW 14
3. Chelling gt Belling Cooker Hood User Manual Contents FIVCOCUIGLIOIN se eaa hey rch an ahaa a oe aac si a aod ert Gio cal Oc aac a 3 Using the Hooda a att a Raw ace Oa Was Ach ee a Ek Sea ae 4 Care and Maintenance nasasa cee ee eee ee eee eee ees 5 INStaNAUON sha his Eee ee eee ee ee Pa Ee a 6 Prepare for INSCANALION fax a s s eevee te aCah wie ye aa Waa ew ge ee ee ee ke 6 Installation Vent outside 2 ee ee es 7 Installation Vent inside 1 es 11 TECHNICA Data i066 nr ae Cee en a he Raa web Be 12 Belling Customer Care Please read this handbook carefully and keep it for future reference Introduction Thank you for buying this high quality hood from Belling we hope it makes and attractive and useful addition to your kitchen Our policy is one of constant development and improvement Strict accuracy of illustrations and specifications is not guaranteed Modification to design and materials may be necessary subsequent to publication Before using the appliance for the first time remove all packaging and protective polythene film Your first year Guarantee To fulfil the conditions of your guarantee this appliance must be correctly installed and operated in accordance with these instructions and only be used for normal domestic purposes Please refer to your guarantee card for further details Please note that the guarantee and service availability only apply to the UK and Republic of
4. Ireland Installation This appliance has been designed for use as an exhausting air evacuation to the outside or filtering indoor air re cycling hood Note This appliance does not come supplied with a ducting kit or carbon filters Details for ordering these parts are at the back of the handbook Because of the complexity and weight of the appliance it is recommended that the installation be carried out by specialist personnel The manufacturer declines all responsibility for damage caused by improper installation Please read this handbook carefully and keep it for future reference Using the Hood OO amp amp Turn on off light On Off Turn on off unit Speed select speed to suit cooking conditions Low light frying boiling Depress this button to enter into low speed and again to turn off motor Medium frying wok cooking heavy boiling Depress this button to enter into medium speed and again to turn off motor High grilling intensive frying and wok cooking Depress this button to enter into high speed and again to turn off motor WARNING Accessible parts may become hot when used with cooking appliances To illuminate the cooking area underneath the hood push the light control button in to the on position 7o switch off press again to return to the To operate the hood press the button for the required speed select 1 low 2 medium or 3 high speed The ne
5. d need renewing after about 4 months of normal use Replacement carbon filters can be obtained from your supplier Saturation of the activated charcoal in the filter will depend on how often the hood is used the type of kitchen and the regularity of cleaning the grease filter The carbon filters cannot be washed renew every 4 months push in firmly Installation Prepare for installation a If you have an outlet to the outside your cooker hood can be connected as below picture by means of an extraction duct enamel aluminium flexible pipe or inflammable material with an interior diameter of 150mm c The cooker hood should be placed at a distance of 65 75cm above the cooking plane for best effect Installation 1 Installation Vent outside Attention Observe the warning in the instruction sheet concerning the operation of the appliance when air is discharged from the room When the range hood and appliance supplied with energy other than electricity are simultaneously in operation the negative pressure in the room must be not exceed 4 Pa 4x10 Bar Drill 3 x 8mm holes to accommodate the bracket Screw and tighten the bracket onto the wall with the screws amp screw plugs provided Screw 4mm x 30mm 1 Offer up the cooker hood and hang onto the wall bracket hook Installation 2 Chimney installation 2 1 For Flat chimney Put the upper chimney into lower chimney Then pul
6. er We recommend that you clean the whole of the Stainless steel area to maintain a uniform finish Sharp objects can mark the surface of Stainless steel but marks will become less noticeable with time To maintain the finish of the stainless steel or to remove any greasy marks wipe the stainless steel surface sparingly with a minimum amount of Baby Oil and kitchen paper Do not use cooking oils as these may contain salt which can damage the Stainless steel surface Before cleaning or maintenance switch off the electricity supply To avoid any fire risk the following cleaning instructions must be followed Grease filters The grease filters absorb grease and dust from cooking fumes which would otherwise damage the inside of the hood 5 The grease filters should be removed and cleaned regularly with normal use this should be every 2 months To clean use warm soapy water or wash in a dishwasher The grease filters may slightly change colour following washing however this does not affect their performance Important Frequent washing is essential to prevent a build up of grease in the filters which could become a fire hazard 1 Remove the filters from the hood 2 Carefully wash the grease filters in hot soapy water and dry with a clean towel 3 Refit the clean filters Carbon filters models installed for use with the re circulation method only The carbon filters absorb cooking odours an
7. ling out the upper chimney upwards Adjust to reach the height required Sliding the chimney to adjust the chimney height When the height you required is reached then hang the fixing hole to the fixing screws as showed in below pictures Installation 2 2 For chimney hood By put the inner chimney into upper chimney Then pulling out the upper chimney upwards Adjust to reach the height required Installation Sliding the chimney to adjust the chimney height When the height you required is reached then fix 2 pcs of 4x8mm screws onto the hole fixing with plate I as showed in below pictures Plate m Drill 2 x 8mm holes to accommodate the plate II Screw and tighten the plate II onto the wall with 2 screws provided m Assemble the chimney onto the unit and fix it with 2 screws Plate 4x8mm Sh 4x30mm 10 Installation Use 2pcs ST4x8mm screws to attach lower and upper chimney together do not fasten screws too much make sure upper decorative chimney can be telescopically adjusted after assembled Upper decorative chimney Inner 1 Lower Chimney bracket 06 Lower decorative chimney Outer Installation Vent inside NOTE Carbon Filter not supplied these can be purchased as an accessory If you do not have an outlet to the outside exhaust pipe is not required and the installation is similar to the one show in section Installation Vent outside
8. on indicator light will light up to show when the fan is operating To switch off press the off button Important safety notes e Keep hob rings covered with pans when switched on to avoid damaging the hood The use of an unprotected flame can cause a fire hazard e Do not flamb food underneath the hood e When frying foods take care to avoid cooking oil flares e Wash the grease filters regularly refer to the cleaning section Do not check filters while the hood is in use e Do not touch the lamps after prolonged use of the appliance Re circulation method only e Keep the air ducting vents clear of obstruction e Change the carbon filters every 4 months The appliance is not to be used by children or persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given Supervision or instruction Care amp Cleaning Before cleaning or maintenance switch off the electricity supply Replacing a light bulb 1 Switch the unit off and unplug the appliance 2 Pat the bulb down and replace the bulb Outer casing All external parts of the outer casing can be safely cleaned with a clean cloth wrung out in hot soapy water Do not use caustic pastes abrasive cleaning powders wire wool hard implements or any products containing chlorides as they will damage the Surfaces Stubborn marks can be removed using a stainless steel clean
Download Pdf Manuals
Related Search