2” Full HD Dash Cam Car DVR with HD Rear View
Contents
1. 0 White Balance WDR Motion Detection Auto Daylight Cloudy Tungsten Fluorescent Off On Off Low Medium High White balance gives the option of 4 preset lighting settings to easily allow you to optimise your KPT 722 for your lighting WDR extends the dynamic range of captured footage When activated the Motion Detection feature allows visible movement to trigger recording Parking Monitor Off On When activated this feature uses the built in battery and G Sensor to monitior any activity after you have parked your car When triggered Parking monitor will record 60 seconds of footage Gravity Sensor Off Low Medium High Setting to adjust the sensitivity of the G sensor Record Audio Off On Turning this setting off mutes the built in microphone Date Stamp Off On Date stamps the footage Plate Number On Movie Enter number plate Enter your cars plate number using the UP DOWN and OK button to select Car Plate P Stamps the footage with your Enter plate number Stamp entered number plate When activated this feature uses the built in battery and G Sensor to monitor any activity Parking Monitor Off On after you have parked your car When triggered Parking monitor will record 60 seconds of footage Rotates the image and footage from the front facing camera Images Off On 1802. Image Resolution 12M 8M 5M 3M 2MHD Photo Format JPG Motion Detection Supported Cycle Recording Supported Memory Card Type Micro SD Card Capacity Up to 32GB USB Port USB Mini Power Port USB 54 1000mAh Frequency 50Hz 60Hz Battery Capacity 500mAh Microphone Speaker Built In Languages English Chinese Russian Please Note We do our best to reflect accurate specifications however periodic updates and changes may occur after this manual was printed We reserve the right to change the parameters without prior notification Warranty Terms amp Conditions Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure This warranty is provided in addition to your rights under the Australian Consumer Law Directed Electronics warrants that this product is free from defects in material and workmanship for a period of 12 months from the date of purchase or for the period stated on the packaging This warranty is only valid where you have used the product in accordance with any recommendations or instructions provided by Directed Electronics This warranty excludes defects resulting from alterations of the p
3. PROTECT button while recording The built in microphone can be quickly muted or unmuted in VIDEO mode by pushing the DOWN button To quickly cycle through the Lamp modes the MENU button can be pressed while recording in VIDEO mode The screen can be put into Screen Saver mode by pressing the MODE button while in VIDEO mode 6 Computer Connection Videos and Photos can be retrieved from the KPT 722 by either connecting the camera directly to your computer using a Mini USB Cable or by connecting the Micro SD Card using a Micro SD Card adapter not included a When you connect the KPT 722 to your computer your KPT 722 will give you the option of Mass Storage or Video Select Mass Storage b The KPT 722 will now appear on your computer as a Removable Disk drive c Open the file explorer on your computer and find the camera listed as a removable disk under Devices d Video and Photo folders will be stored in the file named CARDV e The front and rear cameras will produce two different files the front camera footage will be marked with an A in the title and the rear camera will be marked with a B in the title f For smoother video playback save videos files to your computer prior to reviewing them 7 Interface The KPT 722 has two modes VIDEO and PLAYBACK You can cycle through these modes using the MODE button Each modes respective menu can be accessed by pushin
4. Record indicator Loop length Photo Resolution WDR G Sensor Sensitivity Exposure SD Card Front Camera O CPE 03 08 41 44 Resolution 15 Park Mode 9 Rear Camera 16 Microphone Mute Resolution 17 Power 10 Number Plate 18 Date 11 Recording Duration 19 Time 12 Footage Protected 20 Front Camera View 13 Lamp Mode 21 Rear Camera 14 Motion Detection View Video Menu Unless specified menu items are for forward facing camera only Menu Select Settings Remark Hooi eoe ve e eae Resolution TAOD ZOR ae e space Lower AOA TAARN resolution eA stora e space VGA 640x480 ge Spass Dual Record Off On Turn On Off the Rear View Camera Loop recording Off 3 Mins 5 Mins Loop Recording defines the length of time the KPT 722 records before creating a new file Using the Off setting will record the longest possible loops that the Micro SD Card will allow around 30 mins at 1080P Menu Select Settings Remark 12M 4032x3024 Higher resolution gives your Picture 8M 3264x2448 photos more detail Resolution 5M 2592x1944 3M 2048x1536 2MHD 1920x1080 Adjusting the exposure will counter balance high or low light conditions To brighten 2 0 5 3 4 3 1 0 your footage adjust to a Exposure 2 3 1 3 0 0 1 3 higher exposure To make your 2 3 1 0 4 3 5 3 2 0 footage darker change to a lower exposure The default setting for this is balanced at 0
5. This only rotates image Rotation does not rotate the KPT 722 s controls 15 Playback In this screen the UP and DOWN buttons are used to navigate your videos and photos and the OK button is used to select Videos and photos To access the PLAYBACK Menu highlight the file and press the OK button which will select the file and then press the MENU Button 1 Highlighted Video Photo 3 Locked Icon 2 Video Icon 4 Highlighted File Number Playback Mode File Selected 2018 _0715_170635_001 2 1080P 3 Oar 1 00 00 03 4 CRILKA1 15 07 2618 ul 5 1 Locked File 4 Video duration 2 File Name 5 Power 3 File Resolution Playback Menu Menu Select Settings Remark Allows you to delete either the selected or all photos and video Delete Delete Current Delete All dor dion thelnsaned Micra SD Card Lock Cunenty Unlock Allows you to lock or unlock the selected or all videos and photos Protect Current All Lock i Unlock All stored on the inserted Micro SD Card Format the inserted Micro SD Format Ok Cancel Card deleting all photos videos and data Cycles through the photos and the Slide Show 2 Secs 5 Secs 8 Secs footage thumbnails holding each image for the set amount of time 16 Set Up Menu Menu Select Settings Remark Using the UP DOWN and OK button enter the date and time Date Time Enter Date 24Hr clock to stamp onto your footage Once you have f
6. g the MENU button In the PLAYBACK mode you need to have a file selected before you can bring up the PLAYBACK menu While in the menu the UP and DOWN buttons are used to navigate and the OK button is used to select and confirm The MODE button is used to exit the menu In either mode accessing the menu then pressing the MENU button a second time will display the SETUP menu which contains all of the general settings for the KPT 722 8 Set Time amp Date It s important to have your time and date set correctly as it will record directly onto your video stream and is critical information to prove your case to insurance companies etc To set the time on your KPT 722 follow the directions below a g Ensure you are not currently recording If the red record indicator is flashing at the top left of the screen push the OK button to stop recording Push the MENU button twice taking you to the SETUP menu Using the DOWN button highlight the setting named Date Time and push OK Use the Up and Down buttons to cycle through the numbers and use the OK button to confirm and move between fields Time is set and displayed in a 24 hour format After setting the date and time the bottom DD MM YY fields are used to change format that the date will be displayed Once the date and time have been set the MENU button can be used to save and exit 9 Set Number Plate To set the licence plate number to be stam
7. inished use the MENU button to save and return to the Settings menu Sets the amount of time the KPT Off 10 Secs 20 Secs 722 holds after receiving power Pope Dey 30 Secs before it powers up and starts recording Sets the amount of time the KPT Off 10 Secs 20 Secs 722 holds after receiving power Pawel ONDE 30 Secs before it powers up and starts recording Auto Power Off Off 1 Mins 3 Mins 5 Mins Sets the amount of time of inactivity before the KPT 722 powers down Beep Sound Off On Mute control for key beeps Kevboard Control for turning Off On the y9 Auto Off On back light on the KPT 722 s Back light controls Lamp Setting Auto Off On Control for the LEDs on the front of the camera Changes the output format to ede TRUE either PAL or NTSC Frequency 50Hz 60Hz Screen Hz setting Language Select Language Select Menu language Format the inserted Micro SD Format OK Cancel Card deleting all photos videos and data Default Setting Cancel Ok Restore factory settings Version Ok Displays the installed firmware version 17 Product Specification Screen PAT Lens 160 Imaging Sensor 3 OMP Camera Rotation 180 Minimum Light 1 Lux Video Resolution Front Camera FHD 1080P Video Resolution Rear Camera HD 720P Video Format MOV Frames 30
8. kKeprure 2 Full HD Dash Cam Car DVR with HD Rear View Camera ea Pa amp USER MANUAL KPT 722 parkimatel Before attempting to use or install your Kapture KPT 722 please ensure you have read and understand all of the safety notes below e Avoid leaving your KPT 722 in direct sunlight for extended periods of time in an unventilated space Do not expose your KPT 722 to liquids excessive dusty conditions or temperatures exceeding 60 C Only use the included cables to power and charge the KPT 722 Please do not attempt to adjust the KPT 722 position or settings whilst you are operating your vehicle Ensure you are using your KPT 722 within your countries road laws Please make sure you are familiar with your local road legislation before use 1 Package Contents KPT 722 Car Rear View Windscreen USB Splitter DVR Camera Mount dd Car Charger Rear View User Manual Camera Cable 1 Wide angle Lens 12 2 LED Lamps 3 Mounting Socket 13 4 MENU Button 5 PROTECT Button 14 6 MODE Button 15 7 UP Button 16 8 OK Button 17 9 DOWN Button 18 10 2 7 Screen 19 11 Micro SD Card Slot 20 21 3 General D HDMI Mini Port Adapter required for HDMI not included Mini USB Port This port will not support the Rear View Camera RESET Button PHOTO Button POWER Button Status Light Blue Charging Light Red Speaker Microphone Rear View Came
9. n b Ensure you are not currently recording If the red circle record indicator is flashing at the top left of the screen push the OK button to stop recording C d e Push the MENU button taking you to the VIDEO menu Use the DOWN button to highlight the setting named Loop Recording and push OK Use the UP and DOWN buttons to highlight the required video length The OFF setting will record the longest possible loops that your Micro SD card will allow This is around 30 minutes at 1080P resolution To confirm selection push the OK button the KPT 722 will take you back to the VIDEO menu 11 Set G Sensor The G Sensor monitors any unnatural bumps or shakes and logs the associated footage as Locked ensuring any footage of potential crashes is not recorded over with the regular loop footage a b To set the G Sensor follow the directions below Use the MODE button to make sure you are in VIDEO mode Video camera icon will be displayed in the top left corner of the screen Ensure you are not currently recording If the red circle record indicator is flashing at the top left of the screen push the OK POWER button to stop recording Push the MENU button taking you to the VIDEO menu Use the DOWN button to highlight the setting named Gravity Sensing and push OK POWER Using the UP and DOWN button highlight the required sensitivity of the G Sensor The High Sensitivity setting will allow small bumps
10. ped onto the footage from your KPT 722 follow the directions below a Use the MODE button to make sure you are in VIDEO mode Video camera icon will be displayed in the top left corner of the screen b Ensure you are not currently recording If the red record indicator is flashing at the top left of the screen push the OK button to stop recording c Push the MENU button taking you to the VIDEO menu d Using the DOWN button highlight the setting named Plate Number and push OK e Use the UP and DOWN buttons to cycle through the characters The OK button to confirm and move between fields f Once the final plate character has been entered press OK one last time to save and return to the VIDEO menu g Using the down key highlight the setting named Car Plate Stamp and push OK h Use the UP and DOWN buttons to highlight either OFF or ON i To confirm selection push the OK button the KPT 722 will take you back to the VIDEO menu 10 Set Loop Recording Your KPT 722 has the ability to record in a Loop mode which means older blocks of video files will be overwritten once the memory card becomes full You can set the amount of video block time the KPT 722 will record for before a new video file is started To change the length of the videos that the KPT 722 records follow the directions below a Use the MODE button to make sure you are in VIDEO mode Video camera icon will be displayed in the top left corner of the scree
11. ra a Insert your Micro SD Card not included into the Micro SD Card slot on the side of the camera Ensure that the Micro SD Card is inserted into the camera in the correct orientation metal contacts should be facing the text on the camera reading MICRO SD b The Auto On Off feature will power the KPT 722 up and begin recording as soon as it receives power from the USB Mini connection eg when you start your car 4 Installation a Clean the interior of your front and rear windscreens ensuring that the desired point of installation for both cameras is free of dust and is not obstructing the drivers view Attach the KPT 722 to the Windscreen Mount by inserting the mount s lock peg into the mounting socket on the KPT 722 Remove the protective film from the 2 7 LCD Screen With the mount s suction mount lock switch in the unlocked position press the suction cup onto the desired position on your front windscreen Lock the mount in place by swivelling the lock switch right into the locked position Use the nut to adjust the angle and position of the KPT 722 and tighten to lock your positioning Connect the USB Mini Splitter to the USB Mini Connection on the windscreen mount Remove the protective film from the 3M sticker on the mount of the Rear View Camera Place the Rear view camera at your preferred mounting point on the interior of the rear windscreen and press down ensuring tha
12. roduct accident misuse abuse or neglect In order to claim the warranty you must return the product to the retailer from which it was purchased or if that retailer is part of a National network a store within that chain along with satisfactory proof of purchase The retailer will then return the goods to Directed Electronics Directed Electronics will repair replace or refurbish the product at its discretion The retailer will contact you when the product is ready for collection All costs involved in claiming this warranty including the cost of the retailer sending the product to Directed Electronics will be borne by you Directed Electronics Address 44 Translink Drive Keilor Park Victoria 3042 Ph 61 03 8331 4800 Email service me directed com au Keprure www kapturecam com au www kapturecam co nz CE FE amp O x N15013 x DIREC TED AUSTRALIA amp NZ Parkmate 2015
13. t the adhesive is properly secured Connect the Rear View Camera to the Rear View Camera USB Cable and plug the USB Mini end into the USB Mini Splitter into the port named AV IN Plug the Car Charger into the port named DC 5V on the USB Mini Splitter and connect it to your cars DC power port cigarette lighter port 5 Product Operation a Once the camera is set up with the included Car Charger and a Micro SD Card has been installed the KPT 722 will automatically power on and start recording when the car is started The KPT 722 is designed to be primarily powered by your car s DC power The on board battery is for short use only and mainly serves to power Park mode and brief use for documenting external damage in the case of an incident While recording you will not be able to access the menus or change modes to stop a recording push the OK button The KPT 722 is optimised for Micro SD Cards class 4 and above with a capacity up to 82GB The on board G Sensor registers any activity that could be an accident and saves the footage as a Locked file ensuring that the footage cannot be accidently recorded over To remove Locked files you must first unlock them using the Protect menu navigating to PLAYBACK mode using the MODE key selecting the Locked file pushing the MENU button and selecting Protect Footage can be manually Locked by pressing the
14. to log footage as Locked and Low Sensitivity will require a larger amounts of activity to log footage as Locked To confirm selection push the OK POWER button the KPT 722 will take you back to the VIDEO menu 12 Set Park Mode Park Mode will monitor for activity using the G Sensor while the car is parked even if your ignition is turned off If activity is detected the KPT 722 will record 60 seconds of footage To set park mode on your KPT 722 follow the directions below a Use the MODE button to make sure you are in VIDEO mode Video camera icon will be displayed in the top left corner of the screen Ensure you are not currently recording If the red record indicator is flashing at the top left of the screen push the OK button to stop recording Push the Menu button taking you to the VIDEO menu Using the DOWN button highlight the setting named Parking Monitor and push OK Use the UP and DOWN buttons to highlight either OFF or ON To confirm selection push the OK button the KPT 722 will take you back to the VIDEO menu 13 Set Motion Detection Motion Detection monitors on screen movement and will start recording when movement is detected Motion Detection will also stop recording after 10 seconds of no on screen movement a C Use the MODE button to make sure you are in VIDEO mode Video camera icon will be displayed in the top left corner of the screen Ensure you are not currentl
15. y recording If the red circle record indicator is flashing at the top left of the KPT 722 s screen push the OK button to stop recording Push the MENU button taking you to the VIDEO menu d Using the DOWN button Highlight the setting named Motion Detection and push OK e Using the UP and DOWN button highlight the required sensitivity of motion detection The High setting will allow small amounts of movement to trigger recording and Low will require a larger amounts of activity to trigger recording f To confirm selection push the OK button the KPT 722 will take you back to the VIDEO menu 14 Video This is the default start up screen on right and is how all recording is triggered From this screen you can manually start and stop recording using the OK button Footage can be manually locked by pressing the PROTECT button protecting it from being recorded over The UP button can be used in VIDEO mode to cycle through the display modes These modes change the displayed image on the screen giving the options front view only rear view only or both together using picture in picture The Screen Saver can be turned on and off by pressing the MODE button The Microphone s mute function can be toggled with the DOWN button The LED Lamps three modes can be cycled through using the MENU Button When in VIDEO mode the PHOTO Button on the top of the KPT 722 can be used to capture still images ON OT PE CH LED
Download Pdf Manuals
Related Search