Paramount™ XD Manual Wheelchair User Manual
Contents
1. 3 Place the wheel lock in 1 Bi the unlocked position m and slide it 3 8 closer Adjust wheel lock to the tire 4 Use a 3 8 wrench to tighten the two clamp bolts and engage the lock to check the fit The lock should indent the tire at least 3 8 Tighten clamp bolts securely to eliminate wheel lock movement on frame Z WARNING Ensure wheel locks are adjusted so that they lock in place appropriately before occupying or operating wheelchair 5PX1 INS LAB RevC14 e Paramount XD User Manual 21 6 TRANSPORTING THE E amp J PARAMOUNT XD Z WARNING This wheelchair does not offer seating or occupant restraint equivalent to the seat provided in a motor vehicle To increase your safety while traveling in a motor vehicle always transfer to the vehicle seat and use the restraint provided by the vehicle manufacturer The Paramount XD can easily be transported by folding the wheelchair 1 Detach front rigging from wheelchair 2 Remove the seat cushion if so equipped 3 Fold the wheelchair pull up sharply on the seat sling at front and rear center at the same time To fold wheelchair completely tip the wheelchair sideways so wheel won t drag and press sides together REASSEMBLY 1 Push down with even pressure on seat tubes on both sides Z WARNING Do not place your hand between seat tube and side panel 2 Attach footrests or legrests to wheelchair 3 Reinstall the seat cushion if so equip2. Z WARNING Do not operate this wheelchair on hilly or rough terrain sand wet or icy surfaces or surfaces with impaired traction Ensure that pathway is clear of all obstacles Z WARNING Do not turn wheelchair while going downhill as wheelchair could tip over Z WARNING Do not attempt inclines without anti tippers installed Do not attempt any incline or decline greater than six degrees 10 grade or one foot of rise or fall per ten feet of ramp length 5PX1 INS LAB RevC14 Paramount XD User Manual 5 Z WARNING This wheelchair does not offer seating or occupant restraint equivalent to the seat provided in a motor vehicle To increase your safety while traveling in a motor vehicle always transfer to the vehicle seat and use the restraint provided by the vehicle manufacturer Z WARNING Do not tie down or attach anything to the wheels This could cause tipping and possibly result in injury or damage to the wheelchair Z WARNING The footplates lowest point should clear the ground by at least 2 1 2 inches to permit proper clearance of potential obstruction Z WARNING Doing a wheelie tilting the wheelchair backward until it reaches its balance point is dangerous and could result in personal injury to the user Z WARNING Do not stand or step on the footplates while transferring to or from your wheelchair This could cause the wheelchair to tip or may cause personal injury or damage to your wheelchair Z WARN
3. rearward The elevating legrest mid middle notch is adjustable to three low stop pin iti high last notch in fi positions low mid gh a in first notch and high horizontal elevation Elevation is adjusted by locking a ibe eo slotted plate controlled lever by the legrest release plate lalevating lever onto a stop pin slot legrest in low mid or high position as shown at right Adjust legrest elevation Moving the release lever forward raises the plate notch from the stop pin allowing the plate slot to move over the stop pin and change position Moving the release lever rearward lowers a plate notch onto the stop pin and locks it in place 1 To allow the elevating legrest to move without dropping suddenly support its weight and move the release lever forward Slowly move elevating legrest to desired position Move the release lever rearward to lock notch onto stop pin Ensure elevating legrest is locked in position before letting go of legrest e When the stop pin is in the first notch as shown above the legrest is in low position e When the stop pin is in the middle notch the legrest is in mid position e When the stop pin is in the last notch the legrest is in high horizontal position A WARNING Ensure elevating legrests are locked in place before occupying or operating wheelchair 5PX1 INS LAB RevC14 Paramount XD User Manual 19 Adjust legrest footplate extension len
4. your wheelchair best when it comes to service and repairs Contact your authorized distributor with any questions or concerns regarding the safe operation and maintenance of your wheelchair Regular maintenance is essential for your safety and continued operation of your wheelchair 24 5PX1 INS LAB RevC14 Paramount XD User Manual Check tire wear Examine tires at least once a week for surface wear and cracks and replace them as needed Replace solid rubber tires when they become loose on the rims or cracks appear Check handrims Check handrims at least once a week Inspect each handrim for rough or sharp edges and if any are found replace handrims immediately Ensure that all hardware is properly aligned and secure Check wheel lock engagement Check wheel lock engagement at least once a week See Adjust wheel locks in Section 5 to adjust wheel lock engagement If a wheel lock is worn or damaged replace it immediately Inspect the hardware for looseness or signs of wear Ensure that the locking mechanism operates smoothly The locking assembly should be tight enough so that the wheel can not rotate or the lock slip Check that the locking shoe does not press against the tire when in the unlocked position Excessive force should not be required to either engage or release wheel locks Oil the wheel lock pivot points with one or two drops of 30 weight oil Remove excess oil and dirt Check anti tippers optional Check the an
5. your Graham Field authorized distributor for assistance The person performing adjustments on the Paramount XD has the responsibility of making certain that the user can safely operate the wheelchair with the adjustments selected This person must evaluate the user s ability weight physical condition the environment in which the wheelchair will be used and the terrain over which the wheelchair will travel All adjustments and their page locations are referenced in the index at the end of this manual Specific tools needed to perform each adjustment are identified in adjustment directions A complete list of tools needed to perform all adjustments in this section follows Phillips screwdriver 3 8 wrench M13 wrench M6 hex key REAR WHEELS amp CASTERS We recommend that you do not replace or adjust rear wheel or caster components yourself since special tools and training are required Please contact your Graham Field authorized distributor when your rear wheels or casters need adjustment 14 5PX1 INS LAB RevC14 Paramount XD User Manual ARMS All Paramount XD arms are removable Remove arm 1 Depress lower arm release until it unlocks 2 Hold arm by center of armpad Lift straight up and off Install arm 1 Hold arm by center of armpad 2 Lower arm straight down into sockets and push to lock Remove attach arm 3 Ensure release is locked in place Z WARNING Ensure arms are locked in
6. 1 3 to adjust other footplate extension length Ensure both adjustment knobs are securely tightened and minimum ground clearance is 2 1 2 inches Z WARNING Ensure footplates are securely installed before occupying or operating wheelchair 5PX1 INS LAB RevC14 e Paramount XD User Manual 17 ELEVATING LEGREST DETACHABLE SWINGAWAY Z WARNING The footplates lowest point should be no closer to the ground than 2 1 2 inches to permit proper clearance Z WARNING Do not stand on the footplates this could cause the wheelchair to tip Remove elevating legrest 1 To release lock pull swingaway release lever forward toward front of wheelchair Legrest will swing outward 2 To remove lift legrest straight up off wheelchair hinge pins Attach elevating legrest 1 Set legrest on swingaway release lever Remove attach elevating legrest wheelchair so that legrest hinge plates engage wheelchair hinge pins 2 Swing legrest inward 3 Ensure legrest is locked in place and swingaway release lever is locked in a rearward position toward back of wheelchair Z WARNING Ensure legrests are locked in place before occupying or operating wheelchair 18 5PX1 INS LAB RevC14 e Paramount XD User Manual Adjust legrest elevation Z CAUTION It is possible to adjust the elevating legrest without moving the legrest release lever but to lock it in place and prevent it from falling you must move the lever
7. 4 e Paramount XD User Manual 11 RAMPS AND INCLINES Z WARNING During descent the footplates lowest point should be no closer to the ground than 2 1 2 inches to permit proper clearance Z WARNING Do not attempt inclines without anti tippers installed Do not attempt any incline or decline of more than 6 degrees 10 grade or one foot of rise or fall per ten feet of ramp length Z WARNING Do not use wheel locks to slow your descent Attempting to use wheel locks is likely to result in accidental locking that could cause the wheelchair to stop abruptly suddenly pitch forward or tip sideways Z WARNING Avoid changing direction while descending a ramp or incline as this could cause instability Most people are capable of negotiating short inclines without assistance depending upon upper body strength endurance and the degree of incline Know your own capabilities and limitations in terms of strength and endurance before attempting to negotiate an incline or decline Practice with an attendant or healthcare professional first before attempting any inclines declines curbs or ramps Always inspect the ramp for hazards such as holes slippery or uneven surfaces etc before starting up or down If you can not see the entire ramp ask someone to inspect it for you Ascent Lean the upper part of your body slightly forward as you ascend the incline If it becomes necessary to stop on the incline avoid any abrupt or sudden fo
8. Everest amp Jennings Paramount XD Manual Wheelchair User Manual 5PX1 INS LAB RevC14 2007 GF Health Products Inc Read this manual before operating your wheelchair Save this manual for future use The most current version of this manual can be found online at www grahamfield com CONTENTS 1 INTRODUCTION cassescsiscccscsttecsincstersienscecssestssieicannesiseniiinie 3 2 IMPORTANT SAFETY PRECAUTIONG cccsssseeneeeeees 5 3 GETTING STARVED sci cisssissecdcdeisisteicdic cca cedeletenieeidceenecce 8 A HANDLING TIPS ee ee 9 5 RU IS TIME sii cticasnsesasinntasasantnantcactssnensedsacastsisnstsaninastsenncse 14 6 TRANSPORTING THE E amp J PARAMOUNT XD ccseseeeeeens 22 T MAINTENANCE wuieccdecntcaatnicdedmidcadaiaaes 23 8 TROUBLESHOOTING sscicssicssccenscececcanscteccanectsisaccsvedceesetecsaccsesss 28 9 LIMITED WARRANTY ccsisssissestsnsnssiscsoscscssctscncteterscsesnsasicantscciene 29 LO wssssssscscaceeaecse aunt ucnccitaueveveutiteveususiedsdetstnstndeneanianenee 31 GF Health Products Inc is not responsible for typographical errors All illustrations specifications packaging and warranties contained in this document are based on the latest product information available at the time of printing The most current product information including the most current revision of this manual can be found online at www grahamfield com Graham Field Everest amp Jennings and E amp J are registered trade
9. ING Do not place your hands between seat rail and side panel Z WARNING Always engage wheel locks before transferring using a wheelchair lift or using an elevator Z WARNING Ensure wheelchair is on a stable level surface and engage wheel locks before and during transfer Z WARNING Operate only with anti tippers in place when leaning or tipping Z WARNING Do not lean over the top of the wheelchair back This could cause the wheelchair to tip over Z WARNING To reduce the risk of tipping before leaning or reaching forward sit back in the seat and rotate casters fully toward front of wheelchair Z WARNING Unauthorized modification or the use of non Everest amp Jennings replacement parts could change the structure of the wheelchair void the warranty and create a hazardous condition resulting in serious personal injury 6 5PX1 INS LAB RevC14 Paramount XD User Manual Z WARNING Do not lean on this wheelchair or use it as a walker these are practices which could result in loss of balance and personal injury Z WARNING Do not use your wheelchair on escalators Z WARNING Wheel locks are not brakes Do not use the wheel locks to slow down your wheelchair or while the wheelchair is moving Wheel locks are only intended to keep the wheelchair in place when it is at a complete stop Z WARNING Notice for California Customers California Proposition 65 WARNING This product contains a chemical known to the St
10. SE IF ANY MODEL OR SAMPLE WAS SHOWN TO THE CUSTOMER SUCH MODEL OR SAMPLE WAS USED MERELY TO ILLUSTRATE THE GENERAL TYPE AND QUALITY OF THE PRODUCT AND NOT TO REPRESENT THAT THE PRODUCT WOULD NECESSARILY CONFORM TO THE MODEL OR SAMPLE IN ALL RESPECTS THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PARTS GF SHALL NOT BE LIABLE FOR AND HEREBY DISCLAIMS ANY DIRECT SPECIAL INDIRECT INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS OR INCOME LOSS OF USE DOWNTIME COVER OR EMPLOYEE OR INDEPENDENT CONTRACTOR WAGES PAYMENTS AND BENEFITS The warranties contained herein contain all the representations and warranties with respect to the subject matter of this document and supersede all prior negotiations agreements and understandings with respect thereto The recipient of this document hereby acknowledges and represents that it has not relied on any representation assertion guarantee warranty collateral contract or other assurance except those set out in this document For additional information on this product or this warranty please contact a GF Customer Service Representative NOTES 1 Additional terms and conditions may apply 2 Freight claims must be notated on the Bill of Lading and must be made with immediacy The ICC regulations govern specific requirements for freight claims Failure to abide by those regulations may result ina d
11. al hazard situation or unsafe practice that if not avoided could result in product or property damage Info Provides application recommendations or other useful information to ensure that you get the most from your product 4 5PX1 INS LAB RevC14 Paramount XD User Manual 2 IMPORTANT SAFETY PRECAUTIONS IMPORTANT SAFETY PRECAUTIONS ALWAYS FOLLOW THESE SAFETY PRECAUTIONS WHEN USING YOUR WHEELCHAIR FAILURE TO DO SO COULD RESULT IN PERSONAL INJURY TO YOU OR OTHERS OR DAMAGE TO YOUR WHEELCHAIR Safety requires the constant attention of the wheelchair user and the attendant It is extremely important to learn and always use safe methods of performing basic daily activities Always consult your healthcare professional to determine those methods most suitable for your individual abilities Protect yourself and your wheelchair by having your Paramount XD serviced regularly Whenever any part of your Paramount XD is not functioning properly contact your Graham Field authorized distributor immediately as a hazardous situation could result causing personal injury or damage to your wheelchair ONLY EXCELLENT CONDITION IS ACCEPTABLE WHERE SAFETY IS CONCERNED Periodic inspection adjustment and replacement of worn parts will provide many years of superb performance WARNINGS Z WARNING Paramount XD maximum weight capacity is 650 Ib 295 kg EVENLY DISTRIBUTED Z WARNING Do not operate this wheelchair on streets or roadways
12. ate of California to cause cancer and reproductive or developmental harm Z WARNING GF Health Products Inc specifically disclaims responsibility for any personal injury or property damage which may occur during any use which does not comply with federal state or local laws or ordinances 5PX1 INS LAB RevC14 e Paramount XD User Manual 7 3 GETTING STARTED Please familiarize yourself with main components identified in Paramount XD illustration below rear wheel crossbrace tipping sleeve caster housing wheel lock caster fork 8 5PX1 INS LAB RevC14 Paramount XD User Manual caster wheel 4 HANDLING TIPS The Everest amp Jennings Paramount XD has been designed and engineered to perform as a stable and well balanced unit when used for its intended purpose However it is possible to tip the Paramount XD over if it is used improperly We urge you to learn the characteristics of your wheelchair It is most important to learn safe methods to perform the daily activities basic to your lifestyle Consult your medical professionals for assistance in developing the skills and proper techniques to perform all activities safely BALANCE Proper balance is the key to maintaining the stability of your wheelchair Reaching bending and transferring to or from a wheelchair will change your weight distribution and center of gravity When performing such activities do so as instructed in the following paragraphs to a
13. d repair remember that your Graham Field authorized distributor knows your wheelchair best Thank you for choosing an Everest amp Jennings product We at Graham Field wish to assure you of our continuing commitment to provide innovation and quality in our products The Paramount XD is a manual folding wheelchair suitable for frequent users who require a portable wheelchair fitted to their anatomy without the need of customization or alteration to the center of gravity The Paramount XD intended for indoor and or outdoor use has a maximum weight capacity of 650 Ib 295 kg 5PX1 INS LAB RevC14 e Paramount XD User Manual 3 The person performing adjustments on the Paramount XD has the responsibility of making certain that the user can safely operate the wheelchair with the adjustments selected This person must evaluate the user s ability weight physical condition the environment in which the wheelchair will be used and the terrain over which the wheelchair will travel We recommend the use of anti tippers at all times Please note the following special statements used throughout this manual and their significance Z WARNING Indicates a potential hazard situation or unsafe practice that if not avoided could result in death or serious personal injury Z CAUTION Indicates a potential hazard situation or unsafe practice that if not avoided could result in minor or moderate personal injury A NOTICE Indicates a potenti
14. enial of the freight claim GF will assist you in filing the freight claim 3 Claims for any short shipment must be made within thirty 80 days of the invoice date GF Health Products Inc 2935 Northeast Parkway Atlanta GA 30360 Tel 770 368 4700 Fax 770 368 2386 www grahamfield com 30 5PX1 INS LAB RevC14 e Paramount XD User Manual 10 INDEX A Adjustments 14 Anti tippers check 25 Arm remove 15 Arms check 26 B Backposts check 26 Balance 9 Cc Casters 14 Caster stems check 27 Cleaning your Paramount XD 27 Crossbraces tighten 20 Curbs and steps 13 E Elevating legrest attach 18 Elevating legrest remove 18 Elevating legrest detachable swingaway 18 Elevating legrest elevation adjust 19 Elevating legrest panel position adjust 20 F Footrest attach 16 Footrest remove 16 Footrest detachable swingaway 16 G Getting started 8 H Handling tips 9 Handrims check 25 l Info statement significance 4 Introduction 3 L Limited warranty 29 M Maintenance 23 N NOTICE statement significance 4 P Paramount XD illustration 8 R Ramps and Inclines 12 Reaching bending 10 Rear wheel adjustment check 26 Rear wheels 14 S Safety precautions 5 T Tires check 25 Tools for adjustment list 14 Tools for maintenance list 24 Transfer activities 9 Transporting the E amp J Paramount XD 22 Troubleshooting 28 U Upholstery check 26 W Warnings 5 WARNING stateme
15. gth See Adjust footplate extension length in Footrest Detachable Swingaway section Adjust elevating legrest panel position The legrest panel has three mounting positions one inch apart on legrest tube Refer to picture at right To adjust legrest tube stop elevating legrest 1 Rotate legrest panel hinge plate assembly on legrest tube so that legrest tube stop is in center of hinge plate slot legrest panel hinge plate assembly Adjust legrest panel position 2 Slide legrest panel hinge plate assembly up or down on legrest tube to desired position 3 Rotate legrest panel hinge plate assembly on legrest tube so that legrest tube stop is aligned in desired position Z WARNING Ensure that legrest panels are locked in place before occupying or operating wheelchair CROSSBRACES Tighten crossbraces M13 wrench M6 hex key Check the crossbraces to ensure that the bolt and nut securing both crossbraces in the center of the wheelchair are secure crossbraces should be loose enough to fold easily yet snug enough to take up excess play Use a M13 wrench and M6 hex key to tighten 20 5PX1 INS LAB RevC14 Paramount XD User Manual WHEEL LOCKS Adjust wheel locks One 3 8 wrench 1 Use a 3 8 wrench to loosen the two clamp bolts until the lock slides on the frame T 2 Place the wheel lock 5a Clne in the locked position L HL and slide it into contact with the tire 0
16. in denial of the warranty claim EXCLUSIONS The warranty does not cover and GF shall not be liable for the following 1 Defects damage or other conditions caused in whole or in part by misuse abuse negligence alteration accident freight damage tampering or failure to seek and obtain repair or replacement in a timely manner 2 Products which are not installed used or properly cleaned and maintained as required in the official manual for the applicable product 3 Products considered to be of a non durable nature including but not limited to casters filters fuses gaskets lubricants and charts 4 Accessories or parts not provided by GF 5 Charges by anyone for adjustments repairs replacement parts installation or other work performed upon or in connection with such products which are not expressly authorized in writing in advance by GF 5PX1 INS LAB RevC14 Paramount XD User Manual 29 6 Any labor or shipping charges incurred in the replacement part installation or repair 7 Costs and expenses of regular maintenance and cleaning and 8 Representations and warranties made by any person or entity other than GF ENTIRE WARRANTY EXCLUSIVE REMEDY AND CONSEQUENTIAL DAMAGES DISCLAIMER THIS WARRANTY IS GF S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED GF MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPO
17. ited to your ability and restrictions Forward or sideward Z WARNING Do not attempt to reach objects if you are required to move forward in the seat Do not attempt to retrieve objects from the floor if you must reach down between your knees Do not shift your weight in the direction that you are reaching and or bending this could cause the wheelchair to tip 1 Maneuver the wheelchair as close as possible to the object you wish to reach 2 Rotate both casters fully forward Go forward and then back the wheelchair toward the object to swing the casters fully forward Engage both wheel locks 4 Ensure that the casters are rotated fully forward before reaching If not repeat step 2 10 5PX1 INS LAB RevC14 Paramount XD User Manual Backward Z WARNING Do not engage the wheel locks while reaching or bending backward Should your weight suddenly shift accidentally it is better to roll in that direction than to tip over Z WARNING Do not lean over the back upholstery this could cause the wheelchair to tip 1 Maneuver the wheelchair as close as possible to the object the rear wheels will limit how close you can get 2 Rotate both casters fully forward Go forward and then back the wheelchair toward the object to swing the casters fully forward 3 Reach only as far as your arm will extend without changing your sitting position If in doubt reposition the wheelchair or ask for assistance 5PX1 INS LAB RevC1
18. marks and Paramount is a trademark of GF Health Products Inc 2 5PX1 INS LAB RevC14 e Paramount XD User Manual 1 INTRODUCTION Important safety operating and maintenance instructions that warrant your attention are included in this user manual Read this entire manual carefully before operating your new wheelchair keep it handy for future reference and refer to it as often as necessary to help maintain good performance standards Consult your healthcare professional and GF Health Products Inc Graham Field authorized distributor for assistance in developing and learning safe and effective techniques for performing your daily activities according to your individual physical abilities and needs and to make certain that your wheelchair is properly prescribed and adjusted for your use The safety precautions in this manual are general warnings intended to be used only as basic guidelines You may find it necessary to develop your own methods for safely solving frequently encountered challenges Again consult your professional medical advisors for their recommendations about safety methods and never hesitate to ask for their assistance Your wheelchair should receive frequent regularly scheduled maintenance including an inspection of the mechanical parts to ensure proper operation Some suggested inspection procedures troubleshooting procedures and adjustment procedures are included in this manual When it comes to service an
19. nt significance 4 Warranty limited 29 Wheel bearings check 27 Wheel lock engagement check 25 Wheel locks adjust 21 5PX1 INS LAB RevC14 e Paramount XD User Manual 31 Everest amp Jennings Manufactured for 5GF Health Products Inc 2935 Northeast Parkway Atlanta Georgia 30360 U S A tel 770 368 4700 fax 770 368 2386 GRAHAM FIELD www grahamfield com Made in China
20. ped Z WARNING Ensure that footrests or legrests are locked in place before occupying or operating wheelchair 22 5PX1 INS LAB RevC14 e Paramount XD User Manual 7 MAINTENANCE Protect your E amp J Paramount XD by having it serviced regularly Proper care and maintenance are essential to keep your wheelchair in safe working condition Periodic inspection adjustment and replacement of worn parts will provide many years of superb performance When you believe that a component or part of your Paramount XD is not functioning properly contact your Graham Field authorized distributor immediately as a potentially hazardous condition could result Only excellent condition is acceptable where safety is concerned Service manual There is no service manual for the Paramount XD Please contact your Graham Field authorized distributor with service questions not answered by this manual Info We recommend that you have a Graham Field authorized distributor perform a six month maintenance check as the distributor may find and correct a problem which might otherwise go undetected and eventually cause more serious problems and or personal injury Do it yourself maintenance You can do many of the scheduled maintenance tasks yourself if you have mechanical ability and a few basic tools Refer to the maintenance schedule on the next page for the recommended regularity of each procedure If any maintenance procedure is not clear to you ask you
21. place before occupying or operating wheelchair 5PX1 INS LAB RevC14 e Paramount XD User Manual 15 FRONT RIGGING FOOTREST DETACHABLE SWINGAWAY Z WARNING The footplates lowest point should be no closer to the ground than 2 1 2 inches to permit proper clearance Z WARNING Do not stand on the footplates this could cause the wheelchair to tip Remove footrest 1 To release lock pull swingaway release lever forward toward front of wheelchair Footrest will swing outward 2 To remove lift footrest straight up off wheelchair hinge pins Attach footrest 1 Set footrest on Remove attach footrest wheelchair so that footrest hinge plates engage wheelchair hinge pins 2 Swing footrest inward 3 Ensure swingaway release lever is locked in a rearward position toward back of wheelchair Z WARNING Ensure that footrests are locked in place before occupying or operating wheelchair 16 5PX1 INS LAB RevC14 e Paramount XD User Manual Adjust footplate extension length 1 Remove adjustment knob this will free footplate extension tube to slide inside iC oe footrest hanger tube footrest hanger 2 Reposition footplate extension in desired footplate position D WN 3 Reinstall adjustment reimar a g footplate knob in appropriate adjustment hole for Adjust footplate extension length desired footplate extension length Screw knob in to tighten 4 Follow steps
22. r Graham Field authorized distributor for assistance A NOTICE Improper maintenance can cause operating problem and may affect your warranty Z WARNING Unauthorized modification or the use of non Everest amp Jennings replacement parts could change the structure of the wheelchair void the warranty and create a hazardous condition resulting in serious personal injury 5PX1 INS LAB RevC14 e Paramount XD User Manual 23 MAINTENANCE SCHEDULE Procedure Perform at least every 3 Months Check tire wear Check handrims Check wheel lock engagement Check anti tippers optional Wipe off frame with soft cloth Check handgrips Check upholstery Check rear wheel adjustment Check arms Check backposts push handles Check footrests elevating legrests SISISISYSTS Clean frame Check caster stem rotation GF distributor maintenance check Check rear wheel bearings distributor Check caster bearings distributor List of tools The tools and cleaning supplies listed will assist in the procedures outlined in Section 7 30 weight oil available at most auto parts stores Phillips screwdriver soft cloth mild soap and water solution General care Always evaluate the overall operation of your wheelchair It should function with ease and should travel straight without excessive drag or pull to one side Remember your Graham Field authorized distributor knows
23. rward movement as you resume climbing this could cause tipping 12 5PX1 INS LAB RevC14 Paramount XD User Manual Descent Always face forward when going down a ramp but do not lean forward this could cause tipping Lean slightly backward to increase stability It is critical to keep the wheelchair under control at all times Descent should be made slowly and safely by grasping the handrims however use care as friction heat will be generated We recommend the use of gloves to reduce the effects of friction heat but going slower is a better alternative CURBS AND STEPS Curbs steps and stairways are dangerous obstacles that confront the wheelchair user When you encounter curbs find a way around or use the ramps now available in most locations If you encounter steps and there is no ramp available avoid the steps by utilizing the disabled designated elevators now required in most locations Z WARNING Never attempt to negotiate steps stairs or escalators in your Paramount XD 5PX1 INS LAB RevC14 e Paramount XD User Manual 13 5 ADJUSTMENTS The Paramount XD offers several adjustments to make it easier and more comfortable to drive Section 7 MAINTENANCE offers preventive maintenance suggestions for keeping your wheelchair in excellent condition ensure that all components are in excellent condition before adjusting The following are recommended methods after a few adjustments you may develop your own Always consult
24. s strictly in accordance with good commercial practice and applicable GF instructions and manuals including proper use and maintenance To the extent that a component is warranted by a third party GF conveys all of its rights under that warranty to the original purchaser to the extent permitted This limited warranty shall only apply to defects that are reported to GF s customer service team within the a pplicable warranty period and which upon examination by GF or its authorized representative prove to be a warranty item This limited warranty is not transferable The warranted components and time period are set forth below Sideframes and crossbraces 00ee0e five years Wheels handrims front rigging forks one year All other durable components not listed above six months The applicable warranty period shall commence from date of shipment to the original customer unless there is an expiration date on the component in which case the warranty shall expire on the earlier of warranty period or the expiration date OBTAINING WARRANTY SERVICE A GF Customer Service Representative must authorize warranty service Please contact the GF Customer Service department by calling 678 291 3207 sending a fax request to 770 368 2386 or by e mailing a request to cs grahamfield com Specific directions will be provided by the Customer Service Representative Failure to abide by the specific directions will result
25. st once a month Inspect for sharp edges or cracks which could weaken the arm and replace if found Ensure all attaching screws are present and tight Use a Phillips screwdriver to tighten armpad mounting screws Check for burrs on the screw heads and replace if found Ensure that screws do not extend into the padding Confirm that the posts at base of arm fit correctly in the sockets snug but not binding Check backposts push handles Check backposts at least once a month Ensure that all mounting hardware is securely fastened and that the backposts are not bent or damaged Contact your authorized distributor if you observe cracking or peeling paint or plating 26 5PX1 INS LAB RevC14 Paramount XD User Manual Check footrests amp elevating legrests Check footrests and legrests at least once a month Inspect the locking mechanisms to confirm sure fit Check for cracks burrs or sharp edges and replace if found Ensure that the footrest or legrest will automatically lock securely in place and will not accidentally unlock Cleaning your Paramount XD Wipe off base and seat frame frequently at least once a week using a soft cloth Dry the wheelchair immediately if exposed to moisture Clean the frame every three months with a mild soap and water solution The frame does not need to be waxed Do not use solvents abrasive waxes caustic chemicals or spray silicone Never use abrasive cleansers they could scratch the finish Never
26. ten Bolts should be snug v Rear wheels and or casters may be adjusted improperly Ensure that both rear wheels are mounted in identical positions and that casters are mounted in identical positions s s s vi Caster stem s may be adjusted improperly See distributor to correct adjustment Info Use only Everest amp Jennings replacement parts A Paramount XD parts catalog is available at www grahamfield com to assist in the ordering of parts Z CAUTION A complete inspection of your wheelchair including maintenance servicing and safety checks should be performed by a Graham Field authorized distributor at least every six months Z WARNING Unauthorized modification or the use of non Everest amp Jennings replacement parts could change the structure of the wheelchair void the warranty and create a hazardous condition which could result in serious personal injury looseness in wheelcha squeaks rattles sluggish turning E e i 1 D 5 2 22 5 o o o o lt gt gt 2 D o o Oo i O ojo AA 28 5PX1 INS LAB RevC14 e Paramount XD User Manual 9 LIMITED WARRANTY SCOPE OF WARRANTY GF Health Products Inc GF warrants to the original purchaser only that it will replace or repair components at GF s sole discretion that are defective in material or workmanship under normal use and service All warranties are conditioned upon the proper use of the product
27. ti tippers at least once a week Ensure that anti tippers are securely fastened and properly positioned Check handgrips Check handgrips at least once a week Ensure they are not ripped ensure they are tight and securely fastened 5PX1 INS LAB RevC14 e Paramount XD User Manual 25 Check upholstery Check upholstery at least once a month Inspect for rips tears and worn spots Ensure that all upholstery attaching screws are present properly aligned and well secured Use a Phillips screwdriver to tighten upholstery mounting screws Check attaching screws for sharp edges or stripped screws and replace if found Z WARNING Worn or torn upholstery or upholstery with loose hardware must be replaced immediately It may not support body weight Check rear wheel adjustment Inspect the wheels at least once a month Check alignment by elevating the rear of the wheelchair on a stable object until the rear wheels clear the ground or placing the wheelchair upside down in a stable position such that the wheels can spin freely Spin the wheels there should be no wobble or sideplay and the wheels should spin freely without binding The bearings should be clean and rotate smoothly Check rim sideplay to verify that bearings are not too loose If there is a problem contact your Graham Field authorized distributor If adjustment is required this should be done by your Graham Field authorized distributor only Check arms Check arms at lea
28. use steam or high pressure cleaners Clean upholstery and plastic components at least once a month with a mild soap and water solution Check casters Check the caster stems for proper rotation at least every three months The caster forks must swivel freely to facilitate steering and handling Adjusting the stem nut varies the amount of force required to turn the caster If the nut is too loose the caster will flutter or shimmy if too tight the wheelchair will be difficult to steer If the caster stems require adjustment or the stem bearings require replacement contact your Graham Field authorized distributor Ensure that stems are firmly attached to forks and that forks and stems are not bent Evaluate all threads locking nuts and bearings Check wheel bearings Have your Graham Field authorized distributor check caster and rear wheel axle bearings at least every six months 5PX1 INS LAB RevC14 e Paramount XD User Manual 27 8 TROUBLESHOOTING Continual use of your Paramount XD necessitates maintenance especially if the factory set adjustments have been altered The following troubleshooting guide lists several common problems that may occur and offers corrective actions for each If you are unsure of the solution or unable to diagnose the problem do not hesitate to ask your Graham Field authorized distributor for assistance SYMPTOM Ir PROBABLE CAUSE AND CORRECTIVE ACTION Nuts and or bolts may be loose If so tigh
29. void tipping the wheelchair TRANSFER ACTIVITIES Z WARNING Always ensure that the wheelchair is on a stable level surface and engage wheel locks before transfer Z WARNING Do not step on the footplates this could cause the wheelchair to tip Fold them up and either detach them or swing them aside Z WARNING There is a critical moment when there is little or no seat platform beneath you Take every precaution to reduce this unsupported distance before you attempt transfer Transferring into or out of a wheelchair is a very difficult maneuver Exercise extreme care when transferring without the aid of either an attendant or a patient lift Consult your physician nurse or physical therapist for assistance in developing your individual technique Make sure that the wheelchair is stabilized and will not move or slide during the transfer Take extra precaution to prevent tipping Use good body mechanics to prevent personal injury 5PX1 INS LAB RevC14 e Paramount XD User Manual 9 REACHING BENDING Z WARNING Always turn the casters frontward to provide stability while reaching If in doubt ask for assistance or use a device that will extend your reach without requiring you to shift your weight Although it is not recommended you may find it occasionally necessary to lean or reach from your wheelchair Consult with your healthcare professional for assistance in developing your personal safe reaching or moving techniques su
Download Pdf Manuals
Related Search