EVlink Parking EVF1 - EVW1
Contents
1. The shutter release button indicator light A blinks The shutter is released e Plug the charging cable into the charging station socket out let and into the vehicle socket outlet The shutter release button indicator light A is permanently on The charging indicator light C blinks quickly e The electric vehicle is on charge The charging indicator light C blinks slowly The socket outlet available indicator light H goes out e Press the red Stop button B The charging indicator light C blinks quickly e Unplug the cable from the charging station and the vehicle The charging indicator light C blinks quickly e Close the shutter e The charging station is available The charging indicator light C goes out The shutter release button indicator light A goes out The socket outlet available indicator light H lights up DOCAO063EN 01 07 2013 9 24 EVlink Parking EVF1 EVW1 Charging Station With an RFID Reader Overview of Indicator Lights and Pushbuttons EVF10000000 EVWi1e000000 Q 1 i OK amp EN ink 3 Shutter release button indicator green E Detected fault indicator red indicator light indicator light Maintenance reservation indicator orange indi2. u iua00u00ma000nnnnannn ann nenn nnEnu nn n ann ann ann nenn aaia EE ENEE ere 18 General Characteristics coonoocenacaninonenocanionenencacada don rada nn nun KEREN inde naniii 18 Electrical CharacteriStiCS ici eessen iio id iii 18 E ut d WEE 19 elle LE 19 UCI TEEN 19 Equipment Handling uursrsseersssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnnnnnnnn nenn 19 Protecting the Environment nn a ae 20 Recycling Packaging een aan Heise 20 End of Life Recyclingi 6 0602004 sanana nnd contanlanad civvsuiusccesvsunesececettaascvdececanieteeses 20 DOCAO063EN 01 07 2013 3 24 EVlink Parking EVF1 EVW1 1 Safety Information Important Information NOTICE Read these instructions carefully and look at the equipment to become familiar with the device before trying to install operate or maintain it The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure The addition of one of these symbols to a Danger safety label on a device indicates that an electrical hazard exists which will result in death or personal injury if the instructions are not followed This is the safety alert symbol H warns you of a risk of physical injury You must comply strictly with the safety instructions associated with this symbol to avoid injuring yours
3. Stopping Charging page 12 for charging stations with an RFID reader We recommend cleaning the charging station with a soft dry cloth Never use abrasive pads or detergents DOCAO063EN 01 07 2013 13 24 EVlink Parking EVF1 EVW1 6 Maintenance Troubleshooting Assistance EVF10000000 EVWi1e000000 Q EAink Zi A Ob a ENVink Shutter release button indicator green A indicator light F Detected fault indicator red indicator light B Charging stop button G en indicator orange indicator geg s indicator green indicator H Socket outlet available indicator green indicator light D Shutter I RFID reader E Socket outlet 14 24 DOCA0063EN 01 07 2013 EVlink Parking EVF1 EVW1 Charging Station Status Description of Fault Corrective Action The indicator lights F G No 230 V power supply Check the external 230 V power supply and H on the front panel are off charging station No 24 V power supply Check the internal 24 V power supply energized up and no sockets Fault in sending back status information e Fault in the auxiliary indicating the circuit breaker status plugged in from the power circuit breakers to the open or closed in sending back information to the PLC PLC change the auxiliary indicating the circuit breaker status e Fault in the connections check connection of the auxiliary indicating the circuit breaker status e If the connec
4. blinks Note If the charging station is connected to the supervision system there may be a wait state e Press the red Stop button B The charging indicator light C blinks quickly e Unplug the cable from the charging station and the vehicle The charging indicator light C blinks quickly e Close the shutter e The charging station is available The charging indicator light C goes out The shutter release button indicator light A goes out The socket outlet available indicator light H lights up 12 24 DOCAO063EN 01 07 2013 EVlink Parking EVF1 EVW1 5 Care A CAUTION RISK OF DAMAGE TO EQUIPMENT e Do not spray water on this equipment e Do not clean this equipment while the electric vehicle is charging Failure to follow this instruction can result in injury or equipment damage NOTICE RISK OF DAMAGING THE CHARGING STATION Do not allow the charging station to come into contact with automotive fluids e g gas diesel Failure to follow these instructions can result in equipment damage Before starting to clean the charging station stop charging unplug the charging cable from the charging station socket outlet and check that the socket outlet shutter is lowered For more information see Stopping Charging page 9 for charging stations without an RFID reader and
5. indicator green A indicator light F Detected fault indicator red indicator light B Charging stop button G P indicator orange indicator Cc Sege indicator green indicator H Socket outlet available indicator green indicator light D Shutter I RFID reader E Socket outlet Charging Cable Indicator Lights Charging Station Status Not connected to off Socket not Socket not energized or defective or defective the socket Socket energized and available for charging Socket reserved or undergoing maintenance Socket faulty tamper prevention surge arrester etc Blinking Session open after the badge has been swiped OK 1 Blinking Blinking Socket selected side with LED A on for cable connection Connected to the Blinking Blinking Ap On Socketlocked waiting to charge locked waiting to Socket locked waiting to charge socket andto me Blinking Ee in progress vehicle Charging stopped by the electric vehicle or by the supervision system Off Off Off Charging suspended by the supervision system or by the energy manager Off Off Off Off Charging interrupted safety device tamper prevention overload etc Off Blinking Off Off Off Charging stopped by pressing B awaiting release only on charging stations with an RFID reader DOCAO063EN 01 07 2013 7 24 EVlink Parking EVF1 EVW1 4 Using the Charging Station A A DANGER HAZARD OF ELECTRIC SHOCK ARC FLASH BURNS OR EXPLOSION e Do not
6. use this equipment if it is damaged or if the charging cable appears to be damaged e Charge your vehicle in a well ventilated area as recommended by the manufacturer e Do not modify the equipment installation Failure to follow these instructions will result in death or serious injury A A DANGER RISK OF DAMAGE TO EQUIPMENT AND ELECTRIC SHOCK e Do not use this equipment in the rain or in storm conditions e Do not spray water on this equipment e Do not wash the electric vehicle while it is charging Failure to follow these instructions will result in death or serious injury Charging Station Without an RFID Reader Overview of Indicator Lights and Pushbuttons EVF10000000 EVWi1e000000 Q sl a D ld 4 3 EN ink Aink Shutter release button indicator green a E Socket outlet indicator light B Charging stop button F Detected fault indicator red indicator light c Charging indicator green indicator G Maintenance reservation indicator orange indicator light light D Shutter H Socket outlet available indicator green indicator light 8 24 DOCAO063EN 01 07 2013 EVlink Parking EVF1 EVW1 Starting Charging CO 1 e The charging station is available The socket outlet available indicator light H is on e Choose one side of the charging station if charging station with 2 socket outlets e Press the shutter release button A
7. 1 7 Characteristics General Characteristics IP protection indices e Charging stations IP54 e Socket outlets IP44 in compliance with standard IEC 61851 IK protection index e Charging stations IK10 e Socket outlets IK10 Operating temperature 30 C to 50 C Storage temperature 40 C to 80 C Electrical Characteristics Power supply e 230 V 50 Hz 60 Hz Phase Neutral Earth e 400 V 50 Hz 60 Hz 3 Phases Neutral Earth Earthing system arrange TT or TN IT prohibited ment Power on network side e 7 kW via type 2 or type 3 connector 230 V e 22 kW via type 2 or type 3 connector 400 V Communication e Ethernet with protection and control cabinet e GPRS modem if Modem option sE of plug and socket 1 or 2 plug and socket outlets per unit outlet s Type 2 connection socket e Type 2 according to IEC 62196 e 7 pin connector e max 32 A Type 3 connection socket e Type 3 according to IEC 62196 e 7 pin connector e max 32 A Charging mode Mode 3 according to IEC 61851 1 For the IT earthing system the neutral point connection must be changed for example by installing an isolation transformer with a TT or TN connection downstream 18 24 DOCAO063EN 01 07 2013 EVlink Parking EVF1 EVW1 Certification CB certification Marking C Conforming to IEC 61851 22 Edition 1 0 2001 05 standards IEC 61851 1 Edition 2 0 2010 11 Low Voltage directive 2006 95 EC Electroma
8. DOCAO0063EN 01 EVlink Parking EVF1 EVW1 Parking Charging Stations User Manual 07 2013 www schneider electric com Schneider d Electric EVlink Parking EVF1 EVW1 This document contains general descriptions and or general technical specifications of the products mentioned It cannot be used to determine the suitability or reliability of these products for specific user applications It is the responsibility of each user or integrator to conduct the appropriate risk analysis in full assessing and testing products as regards the application in which they will be used and the execution of this application Neither Schneider Electric nor any of its affiliated companies or subsidiaries can be held responsible for incorrect use of the information contained in this document If you have any suggestions for improvements or correction or have found errors in this publication please notify us No part of this document may be reproduced in any form or by any means electronic or mechanical including photocopying without express written permission from Schneider Electric All relevant state regional and local safety regulations must be observed when installing and using this product For reasons of safety and to ensure compliance with documented system data only the manufacturer should perform repairs to components When equipment is used for applications with technical safety requirements follow the re
9. cator light e B Charging stop button Charging indicator green indicator light Shutter RFID reader Socket outlet O H Socket outlet available indicator green indicator light mu 10 24 DOCA0063EN 01 07 2013 EVlink Parking EVF1 EVW1 Starting Charging CON e The charging station is available The socket outlet available indicator light H is on e Pass the badge over the RFID reader I The maintenance reservation indicator light G blinks Note If the charging station is connected to the supervision system there may be a wait state e Choose one side of the charging station if charging station with 2 socket outlets e Press the shutter release button A The shutter release button indicator light A blinks The shutter is released e Plug the charging cable into the charging station socket out let and into the vehicle socket outlet The shutter release button indicator light A is permanently on The charging indicator light C blinks quickly e The electric vehicle is on charge The charging indicator light C blinks slowly The socket outlet available indicator light H goes out DOCAO063EN 01 07 2013 11 24 EVlink Parking EVF1 EVW1 Stopping Charging e Pass the badge over the RFID reader 1 The maintenance reservation indicator light G
10. e EVlink Parking range have been optimized to reduce the amount of waste produced at the end of their useful life and for better recovery of component parts and materials when following customary processing procedures Products have been designed so that their components can be processed by conventional procedures decontamination where this is recommended reuse and or dismantling in order to improve recycling performance and crushing to separate out the rest of the materials 20 24 DOCAO063EN 01 07 2013 2 DOCA0063EN 01 Schneider Electric Industries SAS 35 rue Joseph Monier CS 30323 F 92506 Rueil Malmaison Cedex www schneider electric com Due to possible changes in standards and equipment the features described in this document in the form of text and images are subject to confirmation by Schneider Electric 07 2013
11. efer to maintenance manual DOCA0031 The green indicator light H on the front Check the continuity of the button panel is not working The charging cable is non compliant Try plugging in a different cable the cable coding resistance does not allow the cable to be detected Despite the plug and Check the plug and socket outlet is e If it is not locked socket outlet being locked properly Check the socket outlet wiring correctly inserted on both Check the socket outlet power supply the charging station and If you cannot detect a problem change the socket outlet the vehicle the charging refer to maintenance manual DOCA0031 indicator light C does not e f it is locked see below blink The charging indicator light is Check the indicator light connection disconnected The charging indicator light is not Change the socket outlet refer to maintenance manual working DOCA0031 and socket outlet into the pushed in far enough charging station press hard charging station the station The position contact on the plug and Change the socket outlet refer to maintenance manual attempts to lock the plug and Socket outlet is defective DOCA0031 socket outlet 5 times without SUCCESS DOCAO063EN 01 07 2013 15 24 EVlink Parking EVF1 EVW1 Charging Station Status Description of Fault Corrective Action After charging the vehicle The wiring is faulty Check the socket outlet wiring the green indicator light The sock
12. elf or putting your life in danger A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which could result in minor or moderate injury NOTICE NOTICE indicates practices that do not involve the risk of bodily injury IMPORTANT NOTE Electrical equipment should be installed serviced and maintained only by qualified personnel No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this equipment A qualified person is one who has skills and knowledge related to the construction operation and installation of electrical equipment and has undertaken safety training in how to identify and avoid the hazards involved This device must not be installed or used if you notice that it is damaged The manufacturer cannot be held responsible for failure to follow the instructions given in this instruction sheet 4 24 DOCAO063EN 01 07 2013 EVlink Parking EVF1 EVW1 2 About This Manual Aim of This Document The purpose of this manual is to provide the information needed to use EVlink Parking EVF1 and EVW1 charging stations A A DANGER RISK OF ELECTROCUTION Do not replace connector units or plates unless you work for Schneid
13. er Electric After Sales Service Failure to follow these instructions will result in death or serious injury Area of Application This user manual applies to the following EVlink Parking charging stations e EVF1eeeeeee 7 22 kW floor standing charging stations e EVWeeeeeee 7 22 kW wall mounted charging stations Related Documents Instruction Sheet for EVlink Parking EVF1 and EVlink Parking EVW1eeeeees HRB50435 Charging Stations EVlink Parking Guide to Installation Configuration and Replacement DOCAO0061FR DOCAO061EN DOCA0061DE DOCAO061ES DOCA0061IT DOCAO061NL EVlink Parking Charging Station Maintenance Manual DOCA0031FR or DOCA0031EN You can download these technical publications and other technical information from our website at www schneider electric com DOCAO063EN 01 07 2013 5 24 EVlink Parking EVF1 EVW1 3 Overview Introduction Description EVlink Parking charging stations are designed for secure car parks used by jointly owned properties businesses vehicle fleets and shopping malls They can be installed indoors or outdoors Depending on the model it may be possible to identify users with an RFID badge The electric vehicle is connected directly to the grid with a special plug and a dedicated circuit according to IEC mode 3 CHAdeMO DC charging The control and protection functions operate continuously in the system Floor standing Wall mounted charging station charging
14. et outlet is faulty Change the socket outlet refer to maintenance manual on the front panel lights DOCA0031 up again but the plug and socket outlet cannot be withdrawn Vehicle charging does The vehicle is in standby mode Open the vehicle door to exit standby mode EE indicator blinks The cable is damaged Try plugging in a different cable The charging station or the vehicle is not Check the charging station with the EVlink vehicle simulator working e If no fault is detected take the vehicle back to the manufacturer e f a fault is detected change the plate refer to maintenance manual DOCA0031 Charging is interrupted while The vehicle is fully charged Check the vehicle charging status the socket is connected The vehicle cannot detect any current Check the charging station s supply wiring single phase charging station Check the connection Check the charging station with the EVlink vehicle simulator check that phase neutral have not been reversed The vehicle detects an overvoltage Check the charging station s supply wiring three phase charging station Check the connection Check the charging station with the EVlink vehicle simulator check that phase neutral have not been reversed Overcurrent Re start charging and measure the current consumption with an ammeter Try connecting the vehicle to a different charging station Change the plate refer to maintenance manual DOCA0031 The cable insulation is damaged Try
15. gnetic Compatibility EMC directive 2004 108 EC Radio and telecommunications e Radio section terminal equipment R amp TTE directive ETSI EN 300 330 1 V1 7 1 1999 5 EC ETSI EN 300 330 2 V1 5 1 ETSI EN 302 291 1 V1 1 1 ETSI EN 302 291 2 V1 1 1 Health section NF EN 50364 2010 NF EN 62369 1 2009 Electrical safety section Covered by tests under the standard IEC EN 61851 1 Edition 2 0 22 Edition 1 0 Electromagnetic compatibility section EMC EN 301 489 1 7 covered by standard IEC EN 61851 1 Edition 2 0 22 Edition 1 0 1 Only for devices equipped with an RFID reader Storage The charging stations are supplied in individual cardboard boxes When commissioning the product all the protection for transport must be removed before energization We recommend storing the charging stations in their packaging sheltered from rain and damp Transport Throughout the transport phase take all necessary measures to keep the pallet stable Equipment Handling EVlink Parking charging stations must be handled by two people as specified in the Employment Code DOCA0063EN 01 07 2013 19 24 EVlink Parking EVF1 EVW1 8 Protecting the Environment Recycling Packaging The packaging materials from this equipment can be recycled Please help protect the environment by recycling them in appropriate containers Thank you for playing your part in protecting the environment End of Life Recycling Products in th
16. he surge arrester is not Overvoltage e Replace the surge arrester refer to maintenance manual working red indicator DOCA0031 light on the cartridge on or or indication on the supervision Replace the surge arrester cartridge refer to maintenance PC manual DOCA0031 The red indicator light F The charging station is faulty Press the red Stop button B is on Unplug the cable from the charging station Close the shutter The charging station is available Plug the cable back in If the fault persists contact Schneider Electric support 16 24 DOCAO063EN 01 07 2013 EVlink Parking EVF1 EVW1 Intervention A A DANGER HAZARD OF ELECTRIC SHOCK ARC FLASH BURNS OR EXPLOSION Do not attempt to remove the caps from the unit Failure to follow these instructions will result in death or serious injury Please refer to maintenance document DOCA0031FR or DOCA0031EN available on our website www schneider electric com EVlink Technical Support The Schneider Electric Customer Care Center is available to answer all your technical questions about EVlink charging stations You can find the contact details for the Schneider Electric Customer Care Center in your country as follows e Browse our website www schneider electric com e Select your country with the Change country option confirm your selection e Click on the Customer Care Center button DOCAO063EN 01 07 2013 17 24 EVlink Parking EVF1 EVW
17. levant instructions Failure to use Schneider Electric software or approved software with our hardware products may result in injury harm or improper operation Failure to follow this instruction can result in injury or equipment damage O 2013 Schneider Electric All rights reserved 2 24 DOCAO063EN 01 07 2013 EVlink Parking EVF1 EVW1 Table of Contents 1 Safety IMFOMMAUON A A 4 Important Information uurssnsneessnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnnnnnrsnnnnnnnnnnnnnnnnnnsnnnnnnnnnn 4 Cen A IMPORTANTNO RE A About NEEN ET 5 Aim Of This DOCUMEN diia a tt 5 Area Of AP DliCath OM civic a A A A da Eege 5 Related Dices eege 5 OvervieW AAA AA AA 6 INTOCUCHON at at iia aa 6 Net 6 Charging Station States ceccecccceceeeeeeceeeeeeeeeee cece n 7 Using the Charging Station users nina nn 8 Charging Station Without an RFID Reader unnnerssnnnennnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen nn 8 Overview of Indicator Lights and Pusbbuttons oooooocccccnnnocccccncccononccncnnnnnnononnnnnan nn cnn inean 8 Starting CHANGING WEE 9 eelere EE 9 Charging Station With an RFID Reader ee 10 Overview of Indicator Lights and Pusbbuttons oooconccccinocccnccocannnnnnnnn cnn nono nc nennen ernennen rra 10 Starting CHargINQ roscar a RA 11 SS EE 12 164 Te 13 METE AAA TO 14 Intervention cio ii A A A hen 17 EVIink Technical SUpport sediaada aa anaia Aeae daaa A 17 Characteristics
18. plugging in a different cable Problem with the socket outlet Change the socket outlet refer to maintenance manual DOCA0031 When you press the Stop The Stop button is not working Change the Stop button refer to maintenance manual button charging does not DOCA0031 Stop charging indicator light The circuit board is not working Change the plate refer to maintenance manual DOCA0031 blinks and the plug and socket outlet remains locked The vehicle does not charge A power cable is missing or damaged Measure the voltage upstream of the contactor even SE a If the voltage is correct use the EVlink vehicle simulator to Sesmsto DEWOTKING locate the problem A load shedding device is connected to Check that a load shedding device is connected and active the charging station and is active Wait for it to authorize charging again The ground resistance exceeds the To check and resolve this problem contact a qualified charging station permissible value electrician The charging cable is The cable does not meet the required Check the cable specifications check that the wire damaged at the end of specifications cross section is suitable for the current delivered charging Cable quality problem Change the charging cable The charging station cap is Accident vandalism Replace the cap refer to maintenance manual DOCA0031 damaged A plug and socket outlet Accident vandalism Replace the shutter refer to maintenance manual DOCA0031 shutter is damaged T
19. station EVF10000000 EVWieeeeeee D A D Ou VA VU Ya 4 a x S W Aink Shutter release button indicator green A P F Detected fault indicator red indicator light indicator light B Charging stop button G en indicator orange indicator Cc a NI green indicator H Socket outlet available indicator green indicator light D Shutter I RFID reader E Socket outlet EVlink Parking charging stations are equipped with either 1 or 2 type T2 connector s or 1 or 2 type T3 connector s The charging power of EVlink Advanced Parking charging stations is either 7 kW or 22 kW For charging stations with a plug and socket outlet this is on the right For charging stations with an RFID reader the administrator and user badges are supplied with the charging station 1 administrator badge 9 user badges These badges are registered or declared by the installer on site once installation is complete For more information refer to the EVlink Parking Guide to Installation Configuration and Replacement reference DOCA0061 EVlink EVlink O lt cad Seipeider Administrator badge Admin User badge User 6 24 DOCAO063EN 01 07 2013 EVlink Parking EVF1 EVW1 Charging Station States EVF10000000 EVWi1e00000 an e ei VY Y Gi eo EA YA Zi nki EN ink Aa Shutter release button
20. tion is OK check the continuity of the indication circuit with an ohmmeter the charging station power supply must be switched off replace the cables e The PLC input card is not working change the input card The indicator lights are not connected Check the indicator light connections The indicator lights are not working Replace the indicator lights refer to maintenance manual DOCA0031 The contactor is stuck or the circuit Change the plate refer to maintenance manual DOCA0031 board is not working The green indicator light H The socket is not detected Check that the plug and socket outlet is fully inserted in the on the front panel stays on charging station press hard SS the socket is plugged The charging cable is damaged Try plugging in a different cable Problem with the circuit board or socket e Check the continuity of the socket outlet if there is a outlet problem replace the socket outlet refer to maintenance manual DOCA0031 Look at the indicator light on the circuit board If it is red switch the station power supply off and then on again If it stays red check the charging station wiring and make sure no connector has come unplugged If the wiring seems all right reflash the program onto the circuit board If this operation is unsuccessful change the plate refer to maintenance manual DOCA0031 If the indicator light turns green try to restart charging If the indicator light is green change the plate r
Download Pdf Manuals
Related Search