PM-60 Pocket Meter Product Manual
Contents
1. PM 60 Pocket Meter Users Manual Mode d emploi Bedienungshandbuch Manual d Uso Manual de uso 60 Pocket Meter Users Manual 2009 Amprobe Test Tools rights reserved Printed in China Limited Warranty and Limitation of Liability Your Amprobe product will be free from defects in material and workmanship for 1 year from the date of purchase This warranty does not cover fuses disposable batteries or damage from accident neglect misuse alteration contamination or abnormal conditions of operation or handling Resellers are not authorized to extend any other warranty on Amprobe s behalf To obtain service during the warranty period return the product with proof of purchase to an authorized Amprobe Test Tools Service Center or to an Amprobe dealer or distributor See Repair Section for details THIS WARRANTY IS YOUR ONLY REMEDY ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STAUTORY INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY ARE HEREBY DISCLAIMED MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES ARISING FROM ANY CAUSE OR THEORY Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages this limitation of liability may not apply to you Repair test tools returned for2. For better measurement accuracy of small value capacitance subtract the residual capacitance of the Meter and leads from measurement Under diode mode LCD displays bad when measuring a diode conducted at forward and reverse bias LCD displays capacitance mode when no measurement at Auto sense mode Under Auto sense mode do not measure a broken component a unknown component or a component with mixed electrical characteristic such as measuring a resistor and a capacitor in parallel The meter may display incorrectly AC V DC Hz Duty A CAUTION When connecting the test leads to the circuit or device connect the black lead first then connect the red lead when removing the test leads remove the red lead first then remove the black lead Volt Sense The number of dashes displaying on the LCD indicates the electric field intensity 7 If no indication voltage could still be present Using only red test probe to work as mains voltage indicator ACA DCA Disconnect EST Red Black SPECIFICATION General Specifications LCD display digits 4000 counts digit large scale LCD readout Measuring rate 3 times sec Polarity Indication Automatic positive implied Overrange display OL or OL Unit symbol indication Automatic power off time Approximately 20 minutes after power on Low battery indicator Display on LCD Power requirement 1 5
3. Overload protection 600V rms Function Ranges Resolution Accuracy 0 5 10 96 0 1 99 996 0 196 D 3096 S Duty S 7095 Square Wave 5 Hz 1KHz Sensitivity 1 5Vp p Overload protection 600V rms Function Ranges Resolution Accuracy 400 0 0 1pA ACA 1 5964 5 D 4 000mA 0 001mA Frequency Response 50 500Hz AC Conversion Type AC Coupled Average Sensing RMS Indication Input Impedance Approx Overload protection 600V rms Function Ranges Resolution Accuracy 400 00A 0 1pA DCA 0 9 5 D 4 000mA 0 001mA Input Impedance Approx Overload protection 600V rms DIODE TEST Test Current Typical 3504A Open Circuit Voltage Max 1 8V DC Input Protection 600V rm C EMC 61326 1 This product complies with requirements of the following European Community Directives 89 336 EEC Electromagnetic Compatibility and 73 23 EEC Low Voltage as amended by 93 68 EEC CE Marking However electrical noise or intense electromagnetic fields in the vicinity of the equipment may disturb the measurement circuit Measuring instruments will also respond to unwanted signals that may be present within the measurement circuit Users should exercise care and take appropriate precautions to avoid misleading results when making measurements in the presence of electronic interference 12 MAINTENACE If there app
4. warranty or non warranty repair or for calibration should be accompanied by the following your name company s name address telephone number and proof of purchase Additionally please include a brief description of the problem or the service requested and include the test leads with the meter Non warranty repair or replacement charges should be remitted in the form of a check a money order credit card with expiration date or a purchase order made payable to Amprobe Test Tools In Warranty Repairs and Replacement All Countries Please read the warranty statement and check your battery before requesting repair During the warranty period any defective test tool can be returned to your Amprobe Test Tools distributor for an exchange for the same or like product Please check the Where to Buy section on www amprobe com for a list of distributors near you Additionally in the United States and Canada In Warranty repair and replacement units can also be sent to a Amprobe Test Tools Service Center see next page for address Non Warranty Repairs and Replacement US and Canada Non warranty repairs in the United States and Canada should be sent to a Amprobe Test Tools Service Center Call Amprobe Test Tools or inquire at your point of purchase for current repair and replacement rates In USA In Canada Amprobe Test Tools Amprobe Test Tools Everett WA 98203 Mississauga 147 1X9 Tel 888 993 5853 Tel 905 890 7600 Fa
5. V x 2 batteries Battery life 50 hours GPA76P Environmental Conditions Indoor Use Calibration One year calibration cycle Operating temperature 0 C 32 F 30 C 86 F 80 RH 30 C 86 F 40 C 104 F 37596 RH 40 C 104 F 50 C 122 F 45 8 Storage temperature 20 to 60 4 to 140 0 to 8096 RH batteries not fitted Temperature coefficient Add 0 2 x Specified accuracy lt 18 C 64 4 F gt 28 C 82 4 F Shock vibration Sinusoidal vibration per MIL T 28800E 5 55 Hz 39 0 00716 maximum Drop Protection 4 feet drop to hardwood on concrete floor Overvoltage category IEC 61010 1 300V CAT IIl 600V CAT Il CAT Application field The circuits are not connected to mains The circuits are directly connected Low voltage installation lll The building installation IV The source of the Low voltage installation Operating altitude 2000m 6562 ft Pollution degree 2 EMC EN 61326 1 Dimensions WxHxD 56 x 12x 112 mm 2 2x 0 5 x 4 4 in Weight 115g 0 25 Ib Accessories Battery installed carry case and Instruction Card Electrical Specifications Accuracy is reading number of digits at 23 C 73 4 F 5 C 41 F 80 RH Function Ranges Resolution Accuracy 400 0mV 0 1mV x 1 5964 5 D 4 000V 0 001V ACV 40 00V 0 01V 0 9 5 D 400 0V 0 1V 600V 1V Fr
6. ears to be a malfunction during the operation of the meter the following steps should be performed in order to isolate the cause of the problem 1 Check the battery Replace the battery immediately when the symbol appears on the LCD 2 Review the operating instructions for possible mistakes in operating procedure Except for the replacement of the battery repair of the meter should be performed only by a Factory Authorized Service Center or by other qualified instrument service personnel The front panel and case can be cleaned with a mild solution of detergent and water Apply sparingly with a soft cloth and allow to dry completely before using Do not use aromatic hydrocarbons or chlorinated solvents for cleaning If the meter is not to be used for periods of longer than 60 days remove the batteries and store them separately Do not attempt to repair this Meter It contains no user serviceable parts Repair or servicing should only be performed by qualified personnel TROUBLE SHOOTING If the instrument fails to operate check batteries and test leads etc and replace as necessary Double check operating procedure as described in this user s manual If the instrument voltage resistance input terminal has subjected to high voltage transient caused by lightning or switching surge to the system by accident or abnormal conditions of operation the series fusible resistors will be blown off become high impedance li
7. equency Response 50 500Hz AC Conversion Type AC Coupled Average Sensing RMS Indication Input Impedance 10 0 100pF Overload protection 600V rms Function Ranges Resolution Accuracy 400 0mV 0 1mV 0 7 5 D 4 000V 0 001V DCV 40 00V 0 01V 0 6 2 D 400 0V 0 1V 600V 1V 0 7 5 D Input Impedance 10 0 100pF Overload protection 600V rms Function Ranges Resolution Accuracy 400 0 0 1 x 0 9 5 D 4 000K 0 001K 40 00K 0 01K 0 9 2 D ohm 400 0K 0 1K 4 000M 0 001M 40 00M 0 01M x 1 5964 5 D Open Circuit Voltage 0 4V There is a little rolling less than 296 Overload protection 600V rms 10 CONTINUITY CHECK Continuity Threshold Approx 500 Continuity Indicator 2 7 KHz Tone Buzzer Input Protection 600V rms Function Ranges Resolution Accuracy 40 00nF 0 01nF 5 0 4nF 400 0nF 0 1nF Cap 4 000 0 001uF 2 2 9 5D 40 00 0 01UF 400 0uF 0 1pF Measuring Time 30sec 400 0pF range 10sec 40 0pF range 3sec other range Overload protection 600V rms Function Ranges Resolution Accuracy 40 00Hz 0 01Hz 400 0Hz 0 1Hz Hz x 0 3964 5 D 4 000KHz 0 001KHz 40 00KHz 0 01kHz Sensitivity gt 10Vp p 40KHz range gt 1 5Vp p other range The signal must have positive and negative waveform of a cycle Max Sensitivity 600V rms
8. ke fuses to protect the user and the instrument Most measuring functions through this terminal will then be open circuit The series fusible resistors and the spark 13 gaps should then be replaced by qualified technician Refer to the LIMITED WARRANTY section for obtaining warranty or repairing service Battery Replacement Refer to the following figure to replace the batteries Visit www Amprobe com for Catalog Application notes Product specifications User manuals e Please Recycle
9. nd maximum permitted voltage Ka between terminal and ground Please remove all the test leads before A preforming maintenance cleaning battery replacement fuse replacement etc C Complies with European Directives Conforms to relevant Australian standards Do not dispose of this pruduct as unsorted E municipal waste Contact a qualified recycler for disposal Warning To ensure safe operation and service of the Meter follow these instructions Failure to observe warnings can result in severe injury or death Do not operate this meter in explosive gas material combustible gas material steam or filled with dust When using test leads or probes keep your fingers behind the finger guards 2 Use the Meter only as specified in this manual or the protection by the Meter might be impaired Always use proper terminals switch position and range for measurements Do not apply more than the rated voltage as marked on Meter between terminals or between any terminal and earth ground To avoid false readings that can lead to electric shock and injury replace battery as soon as low battery indicator appears Disconnect circuit power and discharge all high voltage capacitors before testing resistance continuity diodes or capacitance To reduce the risk of fire or electric shock do not expose this product to rain or moisture UNPACKING AND INSPECTION Your shipping carton
10. should include 1 PM 60 Meter 2 Battery GPA76P 1 5V 1 User s Manual If any of the items are damaged or missing return the complete package to the place of purchase for an exchange INTRODUCTION This meter PM 60 can be measured voltage resistance frequency capacitance diode current uA and continuity It is an electronic measuring instrument that combines several measurement functions in one unit PM 60 multimeter is portable hand held devices useful for basic fault finding and field service work It can be used to troubleshoot electrical problems OPERATION Auto Power Off o pg V The internal sounder will operate continuously with LCD display flashing in two situations in the Data Hold mode 1 The Meter measure a signal different from the LCD reading 2 The measured signal is the same unit as the LCD reading and is larger 50 counts than the LCD reading Auto Range Manual Range Press IT A A Press lt 1sec Bu to change the range Press gt 1sec Selecting Function Press SELECT WM Y Qro Big E SI 1 Lo Sense w w w Note D Last x Hz ES Resistor Capacitor Continuity Diode 1986 E 0580 AUTO SENSE 582 Re del Lef Reg La lack EE E Se D KR OLF Q s nse n 3 NK AUTO SENSE 3002 Red
11. x 425 446 6390 Fax 905 890 6866 Non Warranty Repairs and Replacement Europe European non warranty units can be replaced by your Amprobe amp Test Tools distributor for a nominal charge Please check the Where to Buy section on www amprobe com for a list of distributors near you Amprobe Test Tools Europe In den Engematten 14 79286 Glottertal Germany tel 49 0 7684 8009 0 Correspondence only no repair or replacement available from this address European customers please contact your distributor PM 60 Pocket Meter Red Black A AMPROBE PM 60 Ii UNE 600V Asfi 1 LCD Display 2 Hold function key 3 Function selection key 4 Range key 5 Function Selector 6 Test Leads CONTENTS 5 UNPACKING AND INSPECTION INTRODUCTION OPERATION SPECIFICATION MAINTENACE TROUBLE SHOOTING Battery Replacement SYMBOLS Warning Dangerous Voltage Risk of electric shock A Caution Refer to the user s manual before using this Meter D Double Insulation or Reinforced insulation Alternating Current AC Direct Current DC Low battery indicator L Grou
Download Pdf Manuals
Related Search