Installation and Usage Instructions
Contents
1. Make sure the storage tank shut off valve is OFF Open the sink top faucet Within a few minutes up to 15 the water will start to run from the faucet slowly Let the water run for at least 30 minutes This flushes the carbon filters on first time use After initial flushing open the shut off valve on the tank and close the sink top faucet Tank will now fill Usually 2 to 3 hours After the tank has filled open the sink top faucet and drain all the water until the storage tank is empty and there is only a small flow from the sink top faucet WARNING DO NOT USE FIRST TANK OF WATER Operation regulation Installation diagram ii Plug in electricity i i i 4 Turn on waler source Input water Install watertank Hand Sher plage BAe tee o gho valve So tari Thanconmact cchor wira go his R A a ig e amp Bo A gawd on waler tank lhe a len install drain soddie po Se LAN Dalla ta hele inte the desire pipa fi feelin oy gl Ao Compeyter Cero lgr js pres if Ea mc RE a Let the water run for alleast 30 minutes This flushes lhe carbon filters on first time use 1 Fema temerbane bavang cap efrepare ahousing SUE TROA ae an oul 1 Gallon of waler ta pusing the spigotand into tha purify reglacema nt filters sockolallhe farend of he housing i WAbl comp lately in fesuedctenwh Oaing pinera fom adn2. Installation and user manual This system may be mounted in either a vertical or horizontal position and must be positioned to allow access for service and filter cartridge changing At the same time the assembly should be relatively near the spigot to maximize flow rate The storage tank can be placed on its side without affecting the performance of the system If there is insufficient room under the sink the tank may be located in an adjacent cupboard Installation of water supply connector Easy Connector Water Supply Connector Deliver Valve This water supply connector that comes with the unit is made up of two parts Water Supply Connector 1 2 male x 1 2 female NPT amp Deliver valve 1 4 x 1 4 Simply disconnect cold water line from angle stop bottom or from faucet stud on top Complete with cone washer and seal Assemble the water supply connector by inserting the Deliver valve Screw the deliver valve into the side of the water supply connector using 3 to 4 wraps of Teflon tape Disconnect the water supply line from the cold water faucet underneath sink Attach and tighten water supply connector assembly being careful not to pinch or crimp any tubing or water supply line while tightening Installation of sink top faucet Most sinks have an extra hole for the mounting of additional faucets sprayers or soap dispensers If your sink does not have an additional hole use the following procedure Using a VSR drill wit
3. h a carbide grinding burr gently grind away enough porcelain or enamel to more than accommodate the drill bit about the size of a dime Enough surface material must be removed to expose the base metal Using the 1 4 drill bit drill a 1 4 hole through the base metal Operate the drill slowly and carefully especially when the drill is about to penetrate the metal If necessary use a drop of two of oil in the hole Repeat step 2 Using the 1 2 drill bit Mount the sink top faucet in the hole and using an adjustable wrench or hand to hold the faucet tighten the 9 16 nut Installation of drain saddle Position as far away from the garbage disposal as possible The drain saddle should be installed above the p trap on the vertical or horizontal tailpiece Drill a 1 4 hole into the drain pipe observing the above position Mount drain saddle aligning holes Drill bit may be left in saddle hole for alignment Carefully tighten both screws on drain saddle till snug Do not over tighten Installation of storage tank Wrap 4 to 5 winds of Teflon tape around metal tank threads Hand tighten plastic shut off valve to tank Firm but not over tight Tank should come from the factory with 8 to 14 lbs PSI of air when measured empty Order of the filters 1 Rechts Wassereingang Sedimenifilter weiss hartes Papier 2 Mitte Gac Kohlefilter weiss blau Dichtungsring nach oben 3 Links CB Kohlefilter weiss Plast
4. iknetz Electronic controller The LCD display shows the water quality The reading will be between 000 100 PPM If the reading is 100 PPM you can let the water flow for approx 20 seconds and the reading will go back towards 000 PPM LCD Display shows 777 PPM a The water pressure dropped and for safety reasons the unit shuts off Unplug and plug the power cord the unit should go back to normal working mode b The LCD display continuously shows 777 PPM it s time for a filter change The button strong flush on the control box can be pressed manually For that purpose open the faucet then press the button and then close the faucet The RO unit will automatically flush the filters for a few seconds This is recommended after not using the unit for some time Modus P000 unit is in normal working modus Modus E000 Error By pushing the button on the display the modus can be changed from E to P If the TDS level is to high the display will show the E modus and at the same time a alarm tone will appear It is necessary to strong flush the membrane with the button This might has to be repeated several times Model RO EASY 5BA has a manual flush valve The valve should be opened every 2 3 weeks for aprox 15 seconds Only open to flush membrane LEE PLILP EPI PE PORE EE Oe 5 E Ee i g JE r Ty 7 Y gt i Faucet Input Water Start up procedure With everything connected turn on the water check for leaks
Download Pdf Manuals
Related Search