REX F-0-9– Standalone or Access Controller Black line www.jantar.si
Contents
1. LED and activated output If the registration has failed the controller signals with a longer beep If the registration is successful the user fingerprint is registered and with it the user can open output on the controller If you repeat the process with the same fingerprint this fingerprint will be deleted Next registered fingerprint will take the first available position on the list or position of the deleted fingerprint If you would like to delete the fingerprint of the user that no longer exists you must maintain a list of registered fingerprints arranged in order of registrations positions functions 6 and 7 Function 2 Pulse time Duration of active output or toggle mode Set the duration of active output the time in which you can open the door or set output to toggle mode The time can be set in seconds or minutes Switching time from seconds to minutes and back can be adjusted by using the function 15 Toggle mode means if a user fingerprint is registered output will remain opened if it was closed or closed if it was open till next registration Set the duration of active output with master fingerprint Place the master fingerprint two times on the sensor and remove it 2 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute of active output Duration of active output can be max 120 seconds or 60 minutes When you hear the required number of beeps place a user fingerpri2. Place the user fingerprint on the sensor or approach a user card before 1 beep Wiegand 26 bit reader Place the user fingerprint on the sensor or approach a user card after 1 beep Access controller Place the user fingerprint on the sensor or approach a user card after 4 beeps Function 13 Delete all Reset delete all data to default Delete all with master fingerprint Place the master fingerprint thirteen times on the sensor and remove it 13 double beeps The controller will start to beep every second After three beeps place a user fingerprint on the sensor or approach a user card for confirmation Delete all with master card Approach the master card and remove it after 13 double beeps The controller will start to beep every second After three beeps approach a user card or place a user fingerprint on the sensor for confirmation Delete all with the Codeks Device Manager program Set the Rex to the default settings by using the Codeks Device Manager program Connect the Rex via RS485 communication line to the Spider communication converter USB or NET Connect the Spider to the computer In Codeks Device Manager find the device and perform the Brain Wash function which sets the device to its default settings Default settings A three second pulse five second open time four second pre alarm time door status switch input and push button input have NO contact output is set for fail secure el strike The controll
3. Controller Sound is ON Tamper is OFF Door status switch input normally closed NC Time is set in seconds Sound is OFF Tamper is ON Door status switch input normally closed NC Time is set in seconds Sound is ON Tamper is ON Door status switch input normally closed NC Time is set in seconds Sound is OFF Tamper is OFF Door status switch input normally opened NO Time is set in minutes Sound is ON Tamper is OFF Door status switch input normally opened NO Time is set in minutes Sound is OFF Tamper is ON Door status switch input normally opened NO Time is set in minutes Sound is ON Tamper is ON Door status switch input normally opened NO Time is set in minutes Sound is OFF Tamper is OFF Door status switch input normally closed NC Time is set in minutes Sound is ON Tamper is OFF Door status switch input normally closed NC Time is set in minutes Sound is OFF Tamper is ON Door status switch input normally closed NC Time is set in minutes Sound is ON Tamper is ON Door status switch input normally closed NC Time is set in minutes Function 16 Reset HARD reset Use it instead off manual reset power off on Reset with master fingerprint Place the master fingerprint sixteen times on the sensor and remove it 16 double beeps The controller will start to beep every second After three beeps place a user fingerprint on the sensor or approach a user card for conf
4. an open collector transistor or mechanical switch which is connecting the input pin of the controller to the Ground Outputs Output has a pre installed protection diode for an inductive load It is also protected from current overload The best way is to use a 0 25A el strike or a 0 5A el magnet which has to be connected to the same positive pole as the controller Connect the negative pole to the door strike output wire 3 When the output is active it is pulled to ground This can be changed with function 5 negate output for el magnet Environment It is designed for indoor non condensing applications Do not expose the controller to direct contact with the elements such as rain snow or sunlight If the plastic housing is in a different color than black then there is a chance that the color will change to some extend in a few months or years if exposed to direct sunlight The sensor surface is hard and extremely robust and will withstand years of normal wear and tear Do not subject the sensor to sharp or hard objects since this might cause permanent damage Cleaning should be done with a lint free cotton textile Do not subject the sensor surface to mechanical force You must assure good cable joints protected against moisture otherwise corrosion may damage the controller Damage in such cases is not covered by the warranty Reading range The controller has a program algorithm that at power start sets paramet
5. at least 0 22mm If the cable length exceeds 25m use one twisted pair of UTP cables for the positive pole and one for the negative pole The cable length between power supply and the controller should not exceed 50m Take into consideration that a 0 22mm cable has a resistance of approximately 9 ohm per 100m The power supply at the end of cable should be a minimum of 9V If you are using el strike it is highly recommended that the voltage drop is calculated At greater distances a thicker cable of 0 5mm or more should be used wherever possible If the load is for example 0 5A with el strike then on the 0 22mm cable voltage drop will be 4 5V at 100m For the device with 60mA consumption the voltage drop is 0 5V Reading distance depends on where the controller is installed The presence of metal or interferences can significantly reduce the reading distance DO NOT install the controller directly on metal surfaces and or cover it with a metal cover It is not recommended to install controllers closer than 30cm from each other in any direction Otherwise it may result in inaccurate readings or indeed in the controller not reading at all For the Rex F 3 9 to comply with EMC directives CE you have to put ferrite core on the cable as close to the controller as possible making two turns Inputs outputs and environment Inputs Inputs are realized with opto isolators The input is active when pulled to ground with
6. card Approach the master card and remove it after 4 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute of the pre alarm time Duration of the pre alarm time can be max 120 seconds or 60 minutes When you hear the required number of beeps approach a user card or place a user fingerprint on the sensor for confirmation Function 5 Negate Switch output state This function is used when you connect an electric strike or electric magnet which needs power supply to remain in locked state Switch output state with master fingerprint Place the master fingerprint five times on the sensor and remove it 5 double beeps Within a period of three seconds place a user fingerprint on the sensor or approach a user card The output state will be switched from the current one Switch output state with master card Approach the master card and remove it after 5 double beeps Within a period of three seconds approach a user card or place a user fingerprint on the sensor The output state will be switched from the current one Function 6 Delete a fingerprint or a lost card Delete the next fingerprint or card on the list Use this function if you wish to delete a fingerprint or lost card from the controller In order to use this function you must maintain a list of registered fingerprints and cards arranged by order of registrations so that you can find the fingerprint or card which was registered bef
7. support for the use of this product can be found on http www jantar si forum en CONTACT Jantar d o o Kranjska cesta 24 4202 Naklo web www jantar si SLOVENIA mail sales jantar si 3 2015 www jantar si
8. 12V magnetic locks 0 5A If you will use it as a standalone controller and low consumption electric strike 0 25A you can use power supply Spider W5 Voltage drops and cable signal interferences When you connect the controller use cable with a diameter of at least 0 22mm If the cable length exceeds 25m use one twisted pair of UTP cables for the positive pole and one for the negative pole The cable length between power supply and the controller should not exceed 50m Take into consideration that a 0 22mm cable has a resistance of approximately 9 ohm per 100m The power supply at the end of cable should be a minimum of 9V If you are using el strike it is highly recommended that the voltage drop is calculated At greater distances a thicker cable of 0 5mm or more should be used wherever possible If the load is for example 0 5A with el strike then on the 0 22mm cable voltage drop will be 4 5V at 100m For the device with 60mA consumption the voltage drop is 0 5V Inputs outputs and environment Inputs Inputs are realized with opto isolators The input is active when pulled to ground with an open collector transistor or mechanical switch which is connecting the input pin of the controller to the Ground Outputs Output has a pre installed protection diode for an inductive load It is also protected from current overload The best way is to use a 0 25A el strike or a 0 5A el magnet which has to be connect
9. NC Time is set in seconds Sound is OFF Tamper is OFF Door status switch input normally opened NO Time is set in minutes Sound is ON Tamper is OFF Door status switch input normally opened NO Time is set in minutes Sound is OFF Tamper is ON Door status switch input normally opened NO Time is set in minutes Sound is ON Tamper is ON Door status switch input normally opened NO Time is set in minutes Sound is OFF Tamper is OFF Door status switch input normally closed NC Time is set in minutes Sound is ON Tamper is OFF Door status switch input normally closed NC Time is set in minutes 3 2015 www jantar si REX F 0 9 Standalone or Access Controller Sound is OFF Tamper is ON Door status switch input normally closed NC Time is set in minutes Sound is ON Tamper is ON Door status switch input normally closed NC Time is set in minutes Function 16 Reset HARD reset Use it instead off manual reset power off on Reset with master fingerprint Place the master fingerprint sixteen times on the sensor and remove it 16 double beeps The controller will start to beep every second After three beeps place a user fingerprint on the sensor for confirmation AS AN ACCESS CONTROLLER As an access controller it is intended for controlling entries exits and passes of users in the system and controlling sliding doors ramp el strike turning alarm on off It needs to be set w
10. REX F 0 9 Standalone or Access Controller ll g REX F 0 9 STANDALONE OR ACCESS CONTROLLER The Rex is a controller with built in fingerprint reader It is designed for residential and business buildings offices shops etc In various operation modes the controller allows access for up to 500 users 2 master fingerprints 500 user fingerprints As a standalone controller the entire set up procedure is carried out with the master fingerprint User fingerprints can either be registered or deleted As an access controller the entire set up procedure is carried out with the software The controller signals normal operation with flashing red and green LED It can also be used as a Wiegand 26 bit reader if needed TECHNICAL DATA REX F 0 9 3m vey gee 500 events Push button strike 0 5A Push button Real time clock battery backup max ten hours CONNECTION CABLE Wire Color peel ao Rat ace Specification Memory bi 9 14V DC 2 Gray Black Max 0 5A 3 Green El strike output Data 0 Active GND 4 White Alarm output Data 1 Active GND 5 Yellow Door status switch input Active GND Buzzer input E Push button input ee RS485 A line RS485 B line LED DIODES Color Description Black line Power supply The controller need s external power supply to operate The Spider W40 power supply is sufficient to power two controllers and two 12V electric strikes or two
11. TANDALONE CONTROLLER one controller confirms the successful registration with a lit green The entire set up procedure is carried out with the master fingerprint You can register two master fingerprints The master fingerprints cannot be replaced or duplicated You cannot change any setting without them and neither can we Programming with the master fingerprint First connection to the power supply and registration of the master fingerprints Register master fingerprints Turn on the power supply 2 beeps indicate power on and place your fingerprint on the sensor which you have chosen to be the master fingerprint After the triple beep remove the fingerprint LEDs will begin to flash rapidly indicating recording fingerprint At the end of the recording when the controller starts beeping rapidly once again place the fingerprint on the sensor If the fingerprint is identical to the first one controller confirms the successful registration with a double beep and with the flashing green LED diode If the registration has failed the controller signals with a longer beep If the registration is successful repeat the process for the second master fingerprint If you want to register only one master fingerprint then register the same fingerprint twice Usage of master fingerprint With the master fingerprint you choose the programming function Functions can be confirmed either with user fingerprint Master fingerprint Every time
12. ce a user fingerprint on the sensor or approach a user card for confirmation Set the time till pre alarm with master card Approach the master card and remove it after 3 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute till pre alarm Duration of the time till pre alarm can be max 120 seconds or 60 minutes When you hear the required number of beeps approach a user card or place a user fingerprint on the sensor for confirmation 3 2015 www jantar si REX F 1 9 and REX F 3 9 Standalone or Access Controller Function 4 Pre alarm and alarm Set the pre alarm time This is the time in which the controller with short beeps alerts you that the door was left open If you don t close the door in the pre alarm time the alarm will be triggered and signaled with long beeps by the controller The time can be set in seconds or minutes Switching time from seconds to minutes and back can be adjusted by using the function 15 Set the pre alarm time with master fingerprint Place the master fingerprint four times on the sensor and remove it 4 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute of the pre alarm time Duration of the pre alarm time can be max 120 seconds or 60 minutes When you hear the required number of beeps place a user fingerprint on the sensor or approach a user card for confirmation Set the pre alarm time with master
13. ed to the same positive pole as the controller Connect the negative pole to the door strike output wire 3 When the output is active it is pulled to ground This can be changed with function 5 negate output for el magnet Environment It is designed for indoor non condensing applications Do not expose the controller to direct contact with the elements such as rain snow or sunlight If the plastic housing is in a different color than black then there is a chance that the color will change to some extend in a few months or years if exposed to direct sunlight The sensor surface is hard and extremely robust and will withstand years of normal wear and tear Do not subject the sensor to sharp or hard objects since this might cause permanent damage Cleaning should be done with a lint free cotton textile Do not subject the sensor surface to mechanical force You must assure good cable joints protected against moisture otherwise corrosion may damage the controller Damage in such cases is not covered by the warranty Installation of Rex F Remove black plastic screw covers on the top and the bottom of the controller Install the controller to the wall with two supplied screws Use diagonal holes it enables a small correction of the position of the controller up down left right When the controller is installed put the screw covers back on 3 2015 www jantar si REX F 0 9 Standalone or Access Controller AS A S
14. er fingerprint nine times on the sensor and remove it 9 double beeps The controller will start to beep every second Each beep presents a different function which is selected with a user fingerprint Standalone controller Place the user fingerprint on the sensor before 1 beep Wiegand 26 bit reader Place the user fingerprint on the sensor after 1 beep Access controller Place the user fingerprint on the sensor after 4 beeps Function 13 Delete all Reset delete all data to default Delete all with master fingerprint Place the master fingerprint thirteen times on the sensor and remove it 13 double beeps The controller will start to beep every second After three beeps place a user fingerprint on the sensor confirmation Delete all with the Codeks Device Manager program Set the Rex to the default settings by using the Codeks Device Manager program Connect the Rex via RS485 communication line to the Spider communication converter USB or NET Connect the Spider to the computer In Codeks Device Manager find the device and perform the Brain Wash function which sets the device to its default settings Default settings A three second pulse five second open time four second pre alarm time door status switch input and push button input have NO contact output is set for fail secure el strike The controller is in standalone mode Function 15 Sound alarm output door status switch input NC or NO set the time
15. er is in standalone mode Function 15 Sound alarm output door status switch input NC or NO set the time in minutes or seconds function 2 3 4 Turn on off the sound beep which is heard as a pre alarm and alarm when a user fingerprint or user card is registered Turn on off the accelerometer which triggers the alarm output output1 O1 wire 4 when the controller is moved Set the Input0 I0 wire 5 to normally closed NC or normally opened NO default Set the time in functions 2 3 4 in minutes or seconds Set with master fingerprint or master card Place the master fingerprint fifteen times on the sensor and remove it 15 double beeps or approach the master card and remove it after 15 double beeps The controller will start to beep every second Each beep presents a different function which is selected with a user fingerprint or user card Specification Sound is OFF Tamper is OFF Door status switch input normally opened NO Time is set in seconds Sound is ON Tamper is OFF Door status switch input normally opened NO Time is set in seconds Sound is OFF Tamper is ON Door status switch input normally opened NO Time is set in seconds Sound is ON Tamper is ON Door status switch input normally opened NO Time is set in seconds Sound is OFF Tamper is OFF Door status switch input normally closed NC Time is set in seconds 3 2015 www jantar si REX F 1 9 and REX F 3 9 Standalone or Access
16. erprint on the sensor Remove it after the beep LEDs will begin to flash rapidly indicating recording fingerprint At the end of the recording when the controller starts beeping rapidly once again place the fingerprint on the sensor If the fingerprint is identical to the first one controller confirms the successful registration with a lit green LED and activated output If the registration has failed the controller signals with a longer beep If the registration is successful the user fingerprint is registered and with it the user can open output on the controller If you repeat the process with the same fingerprint this fingerprint will be deleted Next registered fingerprint or card will take the first available position on the list or position of the deleted fingerprint If you would like to delete the fingerprint of the user that no longer exists you must maintain a list of registered fingerprints and cards arranged in order of registrations positions functions 6 and 7 Register user card with master card Approach the master card and remove it after 1 double beep Within a period of three seconds approach a user card You can register more cards at once if you approach them one by one The user card is now registered and with it you can open output on the controller If the card has already been registered it is now deleted and its position is now empty Next registered card or fingerprint will take the first available position
17. ers based on the installation environment so as to ensure an optimal reading range DO NOT install the controller directly on metal surfaces and or cover it with a metal cover it may stop working reading If you plan to test the controller and move it onto different surfaces then you have to reset it power off on on each surface Installation of Rex F Remove black plastic screw covers on the top and the bottom of the controller Install the controller to the wall with two supplied screws Use diagonal holes it enables a small correction of the position of the controller up down left right When the controller is installed put the screw covers back on 3 2015 www jantar si REX F 1 9 and REX F 3 9 Standalone or Access Controller AS A STANDALONE CONTROLLER The entire set up procedure is carried out with the master fingerprint or master card You can register two master fingerprints or two master cards You can also register one master fingerprint and one master card The master fingerprints or master cards cannot be replaced or duplicated You cannot change any setting without them and neither can we Programming with the master fingerprint or master card First connection to the power supply and registration of the master fingerprints or master cards Register master fingerprints Turn on the power supply 2 beeps indicate power on and place your fingerprint on the sensor which you have chosen to be the master finge
18. in minutes or seconds function 2 3 4 Turn on off the sound beep which is heard as a pre alarm and alarm when a user fingerprint is registered Black line Turn on off the accelerometer which triggers the alarm output output1i O1 wire 4 when the controller is moved Set the InputO IO wire 5 to normally closed NC or normally opened NO default Set the time in functions 2 3 4 in minutes or seconds Set with master fingerprint Place the master fingerprint fifteen times on the sensor and remove it 15 double beeps The controller will start to beep every second Each beep presents a different function which is selected with a user fingerprint Specification Sound is OFF Tamper is OFF Door status switch input normally opened NO Time is set in seconds Sound is ON Tamper is OFF Door status switch input normally opened NO Time is set in seconds Sound is OFF Tamper is ON Door status switch input normally opened NO Time is set in seconds Sound is ON Tamper is ON Door status switch input normally opened NO Time is set in seconds Sound is OFF Tamper is OFF Door status switch input normally closed NC Time is set in seconds Sound is ON Tamper is OFF Door status switch input normally closed NC Time is set in seconds Sound is OFF Tamper is ON Door status switch input normally closed NC Time is set in seconds Sound is ON Tamper is ON Door status switch input normally closed
19. ion is not allowed All shields of S FTP cables must be wired together and at one point connected to the earth Individual connections to the earth are not allowed Do not connect the shield of the cable to the ground of the controller In the event of problems in communication a termination resistor needs to be added We recommend using 120 Ohm resistors on each side of the cable Converters are on the RS485 side protected with slow blow fuses and transient voltage suppressors Changing back to standalone controller from access controller In the Codeks Device Manager software do the Brainwash of the controller Address of the controller s switches back to 255 Correct and incorrect position of the finger on the sensor Correct Incorrect ele ORDERING CODES REX box card software Box F Card 1 reading frequency 125kHz cards 3 reading frequency 13 56MHz cards Software 9 CODEKS Description Standalone or access controller in F box with fingerprint reader integrated proximity card reader frequency 125kHz for CODEKS software Standalone or access controller in F box with fingerprint reader integrated proximity card reader frequency 13 56MHz for CODEKS software OTHER Warranty only applies when the controller Rex is used with power supply or and communication converter from the Spider family Please read through our warranty and disclaimer statements Connection scheme and additional
20. irmation Reset with master card Approach the master card and remove it after 16 double beeps The controller will start to beep every second After three beeps approach a user card or place a user fingerprint on the sensor for confirmation AS AN ACCESS CONTROLLER As an access controller it is intended for controlling entries exits and passes of users in the system and controlling sliding doors ramp el strike turning alarm on off It needs to be set with CODEKS software The controller switches to access controller when tables are sent by the software or when it is set to mode 4 with function 9 Change the controller s address from 255 to any number between 1 and 254 If you have more controllers on the communication line don t duplicate addresses Add them one by one on the communication line because every controller has address 255 by default Communication Connect the controller to the computer with one of the power supplies with built in communication converter from the Spider family Spider W5 USB Spider W5 NET Spider W40 NET The RS485 communication bus is used between the controllers and Jantar software Up to 128 controllers can be lined up into one communication line The maximum length of the communication line is 1000 cable meters It is recommended that you use an FTP or S FTP cable Only a serial connection Black line of controllers in a single communication line is allowed Star parallel connect
21. ith CODEKS software The controller switches to access controller when tables are sent by the software or when it is set to mode 4 with function 9 Change the controller s address from 255 to any number between 1 and 254 If you have more controllers on the communication line don t duplicate addresses Add them one by one on the communication line because every controller has address 255 by default Communication Connect the controller to the computer with one of the power supplies with built in communication converter from the Spider family Spider W5 USB Spider W5 NET Spider W40 NET The RS485 communication bus is used between the controllers and Jantar software Up to 128 controllers can be lined up into one communication line The maximum length of the communication line is 1000 cable meters It is recommended that you use an FTP or S FTP cable Only a serial connection of controllers in a single communication line is allowed Star parallel connection is not allowed All shields of S FTP cables must be wired together and at one point connected to the earth Individual connections to the earth are not allowed Do not connect the shield of the cable to the ground of the controller In the event of problems in communication a termination resistor needs to be added We recommend using 120 Ohm resistors on each side of the cable Converters are on the RS485 side protected with slow blow fuses and transient voltage suppressor
22. me can be set in seconds or minutes Switching time from seconds to minutes and back can be adjusted by using the function 15 Set the pre alarm time with master fingerprint Place the master fingerprint four times on the sensor and remove it 4 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute of the pre alarm time Duration of the pre alarm time can be max 120 seconds or 60 minutes When you hear the required number of beeps place a user fingerprint on the sensor for confirmation Function 5 Negate Switch output state This function is used when you connect an electric strike or electric magnet which needs power supply to remain in locked state Switch output state with master fingerprint Place the master fingerprint five times on the sensor and remove it 5 double beeps Within a period of three seconds place a user fingerprint on the sensor The output state will be switched from the current one 3 2015 www jantar si REX F 0 9 Standalone or Access Controller Function 6 Delete a fingerprint Delete the next fingerprint on the list Use this function if you wish to delete a fingerprint from the controller In order to use this function you must maintain a list of registered fingerprints arranged by order of registrations so that you can find the fingerprint which was registered before the one you wish to delete Delete a fingerprint with master fingerprint Place the ma
23. mity card reader with 125kHz or 13 56MHz reading frequency As a standalone controller the entire set up procedure is carried out with the master fingerprint or master card User fingerprints and cards can either be registered or deleted As an access controller the entire set up procedure is carried out with the software The controller signals normal operation with flashing red and green LED It can also be used as a Wiegand 26 bit reader if needed TECHNICAL DATA REX F 125kHz 500 events Inputs Door status ee on OOOO 0 5A Inputs Door status ee Oon OOOO OO Clock Real time clock battery backup CONNECTION CABLE Wire Color Description Wiegand 26 bit Specification 9 14V DC Power supply 2 Gray Black Max 0 5A 3 Green El strike output Data 0 Active GND 4 White Alarm output Data 1 Active GND 5 Yellow Door status switch input Active GND Buzzer input 7 Push button input ee RS485 A line RS485 B line LED DIODES Color Description Black line Power supply The controller need s external power supply to operate The Spider W40 power supply is sufficient to power two controllers and two 12V electric strikes or two 12V magnetic locks 0 5A If you will use it as a standalone controller and low consumption electric strike 0 25A you can use power supply Spider W5 Voltage drops and cable signal interferences When you connect the controller use cable with a diameter of
24. nt on the sensor for confirmation Set toggle mode with master fingerprint Place the master fingerprint two times on the sensor and remove it 2 double beeps Place a user fingerprint on the sensor before the first beep Function 3 Door status switch input Set the time till pre alarm time in which the door can stay open without triggering the pre alarm and consequently the alarm This function is used when the door status switch on el strike is connected to Input0 1I0 wire 5 on the controller The input is normally opened NO by default It can be changed to normally closed NC by using the function 15 The time can be set in seconds or minutes Switching time from seconds to minutes and back can be adjusted by using the function 15 Set the time till pre alarm with master fingerprint Place the master fingerprint three times on the sensor and remove it 3 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute till pre alarm Duration of the time till pre alarm can be max 120 seconds or 60 minutes When you hear the required number of beeps place a user fingerprint on the sensor for confirmation Function 4 Pre alarm and alarm Set the pre alarm time This is the time in which the controller with short beeps alerts you that the door was left open If you don t close the door in the pre alarm time the alarm will be triggered and signaled with long beeps by the controller The ti
25. on the list or position of the deleted card When you have register deleted all of the cards wait until the controller confirms it with double beep To delete a lost user card you must maintain a list of registered cards and fingerprints arranged in order of registrations positions functions 6 and 7 Function 2 Pulse time Duration of active output or toggle mode Set the duration of active output the time in which you can open the door or set output to toggle mode The time can be set in seconds or minutes Switching time from seconds to minutes and back can be adjusted by using the function 15 Toggle mode means if a user fingerprint or card is registered output will remain opened if it was closed or closed if it was open till next registration Set the duration of active output with master fingerprint Place the master fingerprint two times on the sensor and remove it 2 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute of active output Duration of active output can be max 120 seconds or 60 minutes When you hear the required number of beeps place a user fingerprint on the sensor or approach a user card for confirmation Set toggle mode with master fingerprint Place the master fingerprint two times on the sensor and remove it 2 double beeps Place a user fingerprint on the sensor or approach a user card before the first beep Set the duration of active output with maste
26. ore the one you wish to delete Delete a fingerprint or a lost card with master fingerprint Place the master fingerprint six times on the sensor and remove it 6 double beeps Within a period of three seconds place a user fingerprint on the sensor or approach a card which was registered before the one you wish to delete This will delete the next fingerprint or card on the list Next registered fingerprint or card will take the position of a deleted fingerprint or deleted card Delete a fingerprint or a lost card with master card Approach the master card and remove it after 6 double beeps Within a period of three seconds approach the user card or place a user fingerprint on the sensor which was registered before the one you wish to delete This will delete the next fingerprint or card on the list Next registered card or fingerprint will take the position of a deleted card or deleted fingerprint Function 7 Delete a fingerprint or a lost card Delete the previous fingerprint or card on the list Use this function if you wish to delete a fingerprint or lost card from the controller In order to use this function you must maintain a list of registered fingerprints or cards arranged by order of registrations so that you can find the fingerprint or card which was registered after the one you wish to delete Delete a fingerprint or a lost card with master fingerprint Place the master fingerprint seven times on the sensor and remove it 7 do
27. r card Approach the master card and remove it after 2 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute of active output Duration of active output can be max 120 seconds or 60 minutes When you hear the required number of beeps approach a user card or place a user fingerprint on the sensor for confirmation Set toggle mode with master card Approach the master card and remove it after 2 double beeps Approach a user card or place a user fingerprint on the sensor before the first beep Toggle mode is selected Function 3 Door status switch input Set the time till pre alarm time in which the door can stay open without triggering the pre alarm and consequently the alarm This function is used when the door status switch on el strike is connected to Input0 IO wire 5 on the controller The input is normally opened NO by default It can be changed to normally closed NC by using the function 15 The time can be set in seconds or minutes Switching time from seconds to minutes and back can be adjusted by using the function 15 Set the time till pre alarm with master fingerprint Place the master fingerprint three times on the sensor and remove it 3 double beeps The controller will start to beep every second Each beep indicates 1 second or 1 minute till pre alarm Duration of the time till pre alarm can be max 120 seconds or 60 minutes When you hear the required number of beeps pla
28. rent programming functions you need to remove your master fingerprint after the double beep and place it again on the sensor within 2 seconds The number of double beeps indicates the programming function Master cards If you hold the master card in front of the controller every 2 seconds a double beep is heard The number of double beeps indicates the programming function PROGRAMMING FUNCTIONS WITH MASTER FINGERPRINT OR MASTER CARD Function Description 1 _ Register or delete user fingerprints and cards N Switch to Wiegand 26 bit or access controller 13 elete all 15 Sound off on alarm output off on door status switch input NC or NO set time in minutes or seconds 16 D D Delete fingerprint or lost card D D Description of programming functions Function 1 User fingerprints and user cards Register or delete user fingerprints and cards With a registered fingerprint or card output OO wire 3 for an el strike is triggered for the time set in the function 2 In the controller registered fingerprints and cards are arranged in order of their registration Every registered fingerprint and card is saved to its own position For registration or deletion of user fingerprints and cards you can use the master fingerprint or card Black line Register user fingerprint with master fingerprint Place the master fingerprint on the sensor and remove it 1 double beep Within a period of 10 seconds place a user fing
29. rprint After the triple beep remove the fingerprint LEDs will begin to flash rapidly indicating recording fingerprint At the end of the recording when the controller starts beeping rapidly once again place the fingerprint on the sensor If the fingerprint is identical to the first one controller confirms the successful registration with a double beep and with the flashing green LED diode If the registration has failed the controller signals with a longer beep If the registration is successful repeat the process for the second master fingerprint Register master cards Turn the power supply on 2 beeps indicate power on One by one approach two cards you will use as a master cards 3 beeps indicate a successful registration The first two cards registered become master cards All the other cards will be registered as users user cards If you want to register only one master fingerprint then register the same fingerprint twice You can register only one master card if you approach the same card twice You can also register one master fingerprint and one master card Usage of master fingerprint and master card With the master fingerprint or master card you choose the programming function Functions can be confirmed either with user fingerprint or user card Master fingerprint Every time you place the master fingerprint on the sensor you hear one beep successfully read and a double beep programming function To select the diffe
30. s Changing back to standalone controller from access controller In the Codeks Device Manager software do the Brainwash of the controller Address of the controller s switches back to 255 Correct and incorrect position of the finger on the sensor Incorrect Correct Black line ORDERING CODES REX box card software Box F Card 0 only fingerprint reader Software 9 CODEKS Code Description Standalone or access controller in F box with fingerprint reader for CODEKS software OTHER Warranty only applies when the controller Rex is used with power supply or and communication converter from the Spider family Please read through our warranty and disclaimer statements Connection scheme and additional support for the use of this product can be found on http www jantar si forum en CONTACT Jantar d o o Kranjska cesta 24 4202 Naklo web www jantar si SLOVENIA mail sales jantar si 3 2015 www jantar si REX F 1 9 and REX F 3 9 Standalone or Access Controller ll REX F 1 9 and REX F 3 9 STANDALONE OR ACCESS CONTROLLER The Rex is a controller with built in fingerprint reader and proximity card reader It is designed for residential and business buildings offices shops etc In various operation modes the controller allows access for up to 500 users 2 master fingerprints or 2 master cards 500 user fingerprints or user cards The controller can have a proxi
31. ster fingerprint six times on the sensor and remove it 6 double beeps Within a period of three seconds place a user fingerprint on the sensor which was registered before the one you wish to delete This will delete the next fingerprint on the list Next registered fingerprint will take the position of a deleted fingerprint Function 7 Delete a fingerprint Delete the previous fingerprint on the list Use this function if you wish to delete a fingerprint from the controller In order to use this function you must maintain a list of registered fingerprints arranged by order of registrations so that you can find the fingerprint which was registered after the one you wish to delete Delete a fingerprint with master fingerprint Place the master fingerprint seven times on the sensor and remove it 7 double beeps Within a period of three seconds place a user fingerprint on the sensor which was registered after the one you wish to delete This will delete the previous fingerprint on the list Next registered fingerprint will take the position of a deleted fingerprint Function 9 Switch to Wiegand 26 bit access controller or back to standalone controller Switch the controller to a Wiegand 26 bit reader or an access controller To change the controller back to a standalone controller from an access controller you need to make a brainwash with the Codeks or Codeks Device Manager software Switch with master fingerprint Place the mast
32. uble beeps Within a period of three seconds place a user fingerprint on the sensor or approach a card which was registered after the one you wish to delete This will delete the previous fingerprint or card on the list Next registered fingerprint or card will take the position of a deleted fingerprint or deleted card Delete a fingerprint or a lost card with master card Approach the master card and remove it after 7 double beeps Within a period of three seconds approach the user card or place a user fingerprint on the sensor which was registered after the one you wish to delete This will delete the previous fingerprint or card on the list Next registered card or fingerprint will take the position of a deleted card or deleted fingerprint Black line Function 9 Switch to Wiegand 26 bit access controller or back to standalone controller Switch the controller to a Wiegand 26 bit reader or an access controller To change the controller back to a standalone controller from an access controller you need to make a brainwash with the Codeks or Codeks Device Manager software Switch with master fingerprint or master card Place the master fingerprint nine times on the sensor and remove it 9 double beeps or approach the master card and remove it after 9 double beeps The controller will start to beep every second Each beep presents a different function which is selected with a user fingerprint or user card Standalone controller
33. you place the master fingerprint on the sensor you hear one beep successfully read and a double beep programming function To select the different programming functions you need to remove your master fingerprint after the double beep and place it again on the sensor within 2 seconds The number of double beeps indicates the programming function PROGRAMMING FUNCTIONS WITH MASTER FINGERPRINT Function Description Duration of pre alarm D 6 9 Switch to Wiegand 26 bit or access controller ___ Sound off on alarm output off on door status switch input NC or NO set time in minutes or seconds Reset Description of programming functions Function 1 User fingerprints Register or delete user fingerprints With a registered fingerprint output OO wire 3 for an el strike is triggered for the time set in the function 2 In the controller registered fingerprints are arranged in order of their registration Every registered fingerprint is saved to its own position Register user fingerprint with master fingerprint Place the master fingerprint on the sensor and remove it 1 double beep Within a period of 10 seconds place a user fingerprint on the sensor Remove it after the beep LEDs will begin to flash rapidly indicating recording fingerprint At the end of the recording when the controller starts beeping rapidly once again place the fingerprint on the sensor If the fingerprint is identical to the first Black line
Download Pdf Manuals
Related Search