Electric Boiling Pan User`s Manual
Contents
1. 1 diverter 2 automatic relief valve 3 manual vent valve 4 steam trap 5 plug valve 6 pressure gauge 3 Technical Parameters Max working voltage 0 5bar Max operation temperature 140 C Medium steam 4 Installation When installing the safety valve please remove the foreign matters in the diverter and pipeline first then mount the valve to the pipeline vertically 5 Operation 5 1 Automatic relief valve It will release the pressure automatically when the pressure reaches 0 5BAR range 10 5 2 Manual vent valve If the working pressure is out of the pressure relief range you could release the pressure in the interlayer by the manual vent valve Ordinarily it is used for vent testing press to release 10 5 3 Plug valve 6 5 3 1 Pressure in the pan is directly connected to the pressure gauge to show the value During operation set it to position 5 3 2 2 Release the pressure in pan directly with no display of the pressure in gauge 5 3 3 Release the pressure in pan directly with display of the pressure in gauge 5 3 4 The valve is OFF With no display in gauge and no venting Maintenance During operation enhance checking and maintenance of the valve to make the valve act more sensitively and reliably 1 2 3 Clean the valve regularly to prevent block of foreign matters Once leakage is found substitute or repair the valve timely Vent testing of the man2. but the indicator is not on The indicator is not on and the appliance does not heat up The thermostat is defective At least one of the heating elements burns out The thermostat malfunctioning The indicator defective Power supply is abnormal or power is disconnected Replace the thermostat Replace the burnt out heating element Replace the thermostat Replace the indicator Check the power supply and connection to make it supply normally Aforementioned troubles are just for reference If any failure occurs please stop using and inform the professional technicians to check and repair 13
3. C 7EBM601 C9EBM151 Electric Boiling Pan Luxury Electric Range Series User s Manual Dear User amp Client Firstly thanks for purchasing and using our product All the information and guidelines of this user s manual comply with certain applicable regulations which come out from our long term accumulated knowledge and experience as well as current project development situations Limited to some special structures additional specified items or new technology changes the actual usage situation might be some different from what stated in this user s manual Should you have any question please do not hesitate to contact the manufacturer via the method shown in back cover page of this manual For safety purpose and efficient operation please make this document available to users for reference Do have them to read this manual carefully before carry out any action on this device especially when starting This manual is not applicable for those who have physical or mental disabilities insufficient experience and or insufficient knowledge including children The manufacturer declines any responsibility in the event users do not follow the instructions or guidelines stated here The user s manual should be placed close to the device in convenience of users reading before operation We have the full authority to reserve the further technical changes of the device in the scope of further performance improvement characteris
4. day clean the body surfaces and power cord with wet towel containing non corrosive detergent Do not aim at the appliance with water jet directly Water infiltration may damage the electric performance and cause electricity safety accident 3 If salt is needed add it after the water is boiling No rough salt should be used 4 To reduce scaling please use water treated by softener 5 After a long period of operation there may be scaling at interlayer bottom and on heating element remove it regularly in accordance with the hardness of the local water 6 For descaling cut off the power to cool down the furnace body then put a certain proportion in accordance with requirements of scaling remover manufacturer into the interlayer A while later open the water outlet of interlayer to drain out the scaling water Then rinse it with clear water and make it return to operating state 7 lf not going to use the appliance at any time turn off the thermostat and power switch 12 8 If not going to use the appliance for a long period of time clean it completely and store it in a well ventilated warehouse without any corrosive gases 8 Failure Analysis amp Trouble Shooting O omm m tn Power is connected and heating indicator is on but it does not heat up Connect the power and rotate the thermostat the heating indicator illuminates but temperature keeps rising without control Power is connected and heating is normal
5. er working turn all switches to off position and cut off the power supply Precautions for operation Making sure that there is water spills over from pipe before carrying out any operations everyday Otherwise the appliance and other internal components may be damaged When checking press the button on valve E to make the needle of pressure gauge point to 0 position Then turn on the handle H of level valve If there is any water flows out from pipe I turn off the handle H timely If there is no water please wait till the water comes out then turn off handle H in time A water inlet pipe C pressure gauge E G K manual pressure relief valve energy regulating switch Overflow pipe interlayer water inlet 5 1 Drain Valve 1 Switch Diagram TSI pressure gauge switch automatic pressure relief valve Inlet switch level valve interlayer water drain valve water outlet interlayer OFF 2 Part Name valve body spool handle connecting nut seal ring 605 7 O ring 555 7 O ring pin circlip Op a ee oe eS 3 Technical Parameters Max working voltage 0 5bar Max operation temperature 140 C Medium water O ring lubricating medium KLUBER 703 lubricating grease 4 Installation 4 1 Installment of valve body and pipeline When installing the drain valve the valve cavity and pipeline should be cleaned no attachment is allowed Screw the connecting nut into
6. is loose whether the voltage is normal and whether the safety grounding is reliable The appliance should be positioned at a stable area with a minimum clearance of 10cm away from non combustible substances e g walls windows etc on both sides and 20cm at back side The fixed arrangement of wire should be equipped with an all pole disconnecting switch with a contact opening of 3mm on its poles It is advisable to install a grounding leakage protection switch Do not pile up sundries in front of the switch for convenient operation sake Vicinity of the mounting position should not store flammable or explosive objects The ambient temperature should be lower than 45 C and the relative humidity should be below 85 Installation of the appliance should be done by professional technicians 1 3 Special Note 1 This product is a commercial machine that needs to be operated by trained cook not applicable for household use Do not sway or tilt the appliance during operation Do not dismantle or self modify the machine Dismantlement and self modification may cause casualty Do not open the housing of the machine This product contains high voltage circuit housing dismantlement may cause electric shock Before cleaning unplug and cut off the power supply During cleaning do not aim at the appliance with water jet Water may conduct electricity that may cause electric shock due to leakage 7 Do not pat the product or put any heavy
7. objects onto it Abnormal operation may Cause damage and danger 8 High temperature may cause scald Do not touch the appliance with hands directly due to high temperature during or after operation 9 To prevent damage turn off the switch ASAP when near the thunder zone 10 Do not destroy the control panel with hard or sharp objects 11 After working turn off the switch 12 If the power cord is damaged to avoid hazard replacement should be done by manufacturer or its maintenance department or similar professional personnel 5 Working Instructions amp Operation Flow 1 Before using check all the parameters and installation to ensure correctness 2 Connect the water source to water inlet K on left side of bottom rotate the inlet pipe A to the appliance 3 Turn on the inlet switch F to fill water into the appliance to desired capacity Then turn it off and remove pipe A 4 Turn on the inlet switch H and full water switch I When the water spills over from switch I turn the switches off in order 5 Power on turn on the energy regulating switch G to start working 6 Press the button on manual pressure relief valve E 30min later from power on to release the air in the interlayer till the steam occurs Note It is advisable to press the button on valve E with a tool to prevent steam burns 7 During operation adjust the energy regulating switch G in accordance with food condition in the appliance or requirements 8 Aft
8. ousing of the appliance should be grounded to ensure safety Thanks for your cooperation Contents Functional Introduction ccccc cece eee eeseeeeeeeeeeeeeneeaees Structure Schematic Diagram amp Working Principle Basic Features amp Parametels cccce cee ceeeeseeeseees Precautions amp Recommendations ccce eee eeeeeeeee Working Instructions amp Operation FIOW cecceeeee es Routine Inspection sacuecasesstwdshdediva cdteeai madd vai eiadecbetadedhidees Cleaning amp Maintenance c ccc ccc cece cece eeeeseeeeeee ees Failure Analysis amp Trouble Shooting ccseeeeeeee ees 1 Functional Introduction This product is manufactured by our company which is combined with advantages from home and abroad It is novel in design reasonable in structure easy in operation all stainless steel made durable in using and convenient in maintenance It heats via the hot steam in interlayer Also it is characterized by low consumption fast heating up and non stick Therefore it is the ideal equipment for professional kitchen to cook soup and porridge 2 Structure Schematic Diagram amp Working Principle 2 1 Structure Schematic Diagram C7EBM601 C9EBM151 2 2 Structural amp Functional Features Smooth surface treatment easy to clean very sanitary and clean Desired temperature can be set according
9. the pipeline with a wrench of 3 and tighten it Meanwhile please avoid tightening with too much strength otherwise it may damage the seal ring 4 2 Dismounting the valve body and spool 4 2 1 Turn the valve to ON position 4 2 2 Turn the valve to the position bya A L movement 4 2 3 Draw out the spool for cleaning and maintenance 4 2 4 Replace the spool in reverse procedure of drawing out 4 3 Attention During installation please handle gently do not throw otherwise the components may be damaged 5 Maintenance Have the valve cleaned and maintained after using Main procedure as follows 5 1 Turn the drain valve on and off to check the leakage 5 2 Draw out the spool for cleaning and maintenance as 4 2 5 3 Have all the components cleaned and coat the O ring with lubricating grease 5 4 Replace the spool and make it in OFF state 6 Common Failure amp Troubleshooting The turnoff is not tight The pipeline is seized b i Te i Remove the foreign matters enough foreign matters Connection surface of the The connecting nut is Tighten the nut valve body and pipeline 0ose leaks The gasket is damaged Replace the gasket o Draw out the spool and The O ring is damaged The valve body leaks replace the O ring internally There is foreign matters Draw out the spool and in the O ring remove the foreign matters 5 2 Steam Safety Valve 1 Safety Valve Diagram 2 Part Name
10. tic development J Warning Any self modification wrong installation adjustment or maintenance can lead to property loss or casualty Please contact the manufacturer for any adjustment or maintenance and have the work done by a trained amp qualified person For your safety sake please keep the machine away from any liquid gas or other object which is flammable or explosive This appliance should not be operated by those who have physiological perceptual or mental disabilities or those who have insufficient experience or knowledge including children Only in conditions of being given sufficient supervise amp guarantee of personal safety as well as proper instructions amp guidance those who were mentioned above can make some particular operation of this device Keep children away from the device Preserve this manual safely When passing on selling the device to a third party the manuals must be handed over along with the device All users must operate the device complying with the user s manual and related safety guidelines Do not store or use gas liquid or object that is flammable or explosive in the vicinity of the mounting position of the appliance If this appliance is placed near walls partitions or kitchen furniture and the like it is advisable to make these facilities with non combustible material otherwise cover them with non combustible heat resistant material and pay attention to fire prevention regulations H
11. to requirement and food condition Stainless steel made with withdrawable stainless steel pan Fast heating up easy operation and convenient maintenance a Oo ae 2 3 Electrical Diagram Luxury Electric Boiling Pan 3N 380VAC 50Hz XL N amp O O Li amp rO _O4 L2 amp L3 amp EP amp j b le f a oe KM1 p A auzas KM2 KM1 2 A C contactor ail 8S Temp limiter oo ST2 proportional controller HL heating indicator EH1 EH2 heating element XL terminals ST1 thermostat EH EH2 3 Basic Features amp Parameters Temperature C7EBM601 3N 380V 50Hz 30 110 700x700x850 60 C9EBM151 3N 380V 50Hz 30 110 800x900x850 60 4 Precautions amp Recommendations 1 1 Transportation and Storage During transportation the machine should be carefully handled and do not put it upside down to prevent from damaging to the shell and inside The packaged machine should be stored in a ventilated warehouse without corrosive gas If it needs to be stored in open air temporarily measurement against raining is needed 1 2 Notice for Installment The supply voltage should comply with the working voltage of the appliance The appliance is equipped with an earth bolt at its back which should be connected with copper wire no less than 1 5mm and earth wire that conforming to safety regulations reliably After installation check that whether the connection
12. ual vent valve shall be performed periodically in the case of doing no harm to human body A periodical inspection shall be carried out at lease once a year to guarantee the sensitivity and reliability of the valve Principal inspections opening pressure of the automatical relief valve rotation of the manual vent valve and plug valve and leakage 7 Fault 7 1 The safety valve is opened though specific relief pressure is not reached affecting the normal work 7 2 The safety valve does not open when the relief pressure is exceeded offset 10 7 3 There is leakage 7 4 When aforementioned situations occur send the valve back to the manufacturer to check and repair Dismantlement shall be done by professional personnel only 6 Routine Inspection It is necessary to check the machine daily Check the machine regularly can avoid serious accident happens Stop using if user feels that there are some problems in the circuit or machine Check the situation of the machine before or after using every day Before using Whether the machine is tilted Whether the control panel is damaged Whether the power cord is aging cracking or damaged During using Whether there is strange smell or vibration noise Whether the temperature is out of control or any electric leakage Whether the power is normal 7 Cleaning amp Maintenance 1 Before cleaning cut off the power supply first to prevent unexpected accidents 2 After working every
Download Pdf Manuals
Related Search