Custom Dynamics® Spyder TIPS-NS Installation Instructions
Contents
1. 6 Remove Instrument cluster by following the instructions in your owners manual under the headlight bulb replace ment section 7 Route blue wire up into the area behind instrument cluster Use tie wraps as needed to keep away from hot or moving parts 8 Locate the wires going to front turn signals Test wires to determine which wire is the positive wire going to front turn signal We would normally tell you a color wire to attach to however we have seen BRP reverse the color code in these connectors with no rhyme or reason Therefore a test light is the best method to assure the polarity is correct 9 Using the supplied Posi Tap connectors attach blue wire from the TIPS unit to the positive wire going to the turn signals 10 Test operation TIPS unit will flash the fender lights in an alternating pattern with the front turn signal for maxi mum visibility 11 Reinstall instrument cluster and covers ST amp ST S Models 10 11 12 13 With the blue wire routed up through the body into the upper nose area it must now be routed up to the turn sig nal area Using a wire guide tool will simplify this process a long flexible piece of wire or long zip tie will work well for fishing wire through the hard to reach places Tie wrap wires as need to prevent them from hanging or coming in contact with hot moving parts See Photo on next page for reference model shown is an RT but the process is the same Make2. amp ST ST S the factory mirror assemblies must be removed from the bike to allow access to the turn signal wires Please refer to a detailed service manual or your local Spyder service dealer for instructions on how to remove them Custom Dynamics is not liable for damage resulting from improperly re moved or installed equipment Note Before turn signal wire can be routed depending on your model open the front hood remove body panels to allow access to areas wiring will be routed Questions Call us at 1 800 382 1388 M TH 8 30AM 5 30PM FR 9 30AM 5 30PM EST 07 2014SM Installation Instructions Page 2 Tips Module Installation All Models Plug the appropriate harness connector into each side f the connector you nplugged on the bike Male to female and female to male Locate and unplug the connector coming from the fender underneath the A frame suspension Plug the TIPS module into each 3 pin connect or making sure the blue turn wire goes toward the bike Wire is up through the top side panel tie wrap as needed and get ready to rot turn_signal wir ing Go to next page and follow directions for e your model Route the blue wire up the A frame Tie wrap wires as needed then route wire up to front nose area up top Panel must be up or removed Questions Call us at 1 800 382 1388 M TH 8 30AM 5 30PM FR 9 30AM 5 30PM EST 07 2014SM Installation Instructions Page 3 RS S Models
3. have seen BRP reverse the color code in these connectors with no rhyme or reason Therefore a test light is the best method to assure the polari ty is correct Using the supplied Posi Tap connectors attach blue wire from the TIPS unit to the positive wire going to each turn signal See Photo below Tuck the turn signal wires back into the hole take care that Posi Tap is on the inside of the bike and not ex posed Test operation of the TIPS units power on the bike and test both left and right turn signals All lights on the fender should flash with alternately with the turn signals on the bike Re install mirrors and body panels Routing wire to turn signal Turn Signal Cable to the Mirror Questions Call us at 1 800 382 1388 M TH 8 30AM 5 30PM FR 9 30AM 5 30PM EST 07 2014SM
4. sure the factory mirror assemblies have been removed from the bike to allow access to the turn signal wires as noted on the first page If you have not please refer to a detailed service manual or your local Spyder service dealer for instructions on how to remove them With the mirror assembly removed pull the slack on the cable until the entire length of it is showing Your tap in point should be as close to the bike as possible to allow the posi Tap connections to fit back into the hole see photo on page 4 for reference You will need to strip the sheathing off the cable to allow tap in access to wire take care not to cut or fray wires while removing Once the turn signal wires are exposed test wires to determine which wire is the positive wire going to front turn signal We would normally tell you a color wire to attach to however we have seen BRP reverse the color code in these connectors with no rhyme or reason Therefore a test light is the best method to assure the polari ty is correct Using the supplied Posi Tap connectors attach blue wire from the TIPS unit to the positive wire going to each turn signal Tuck the turn signal wires back into the hole take care that Posi Tap is on the inside of the bike and not ex posed Test operation of the TIPS units power on the bike and test both left and right turn signals All lights on the fender should flash with alternately with the turn signals on the bike Re i
5. Custom Dynamics Spyder TIPS NS Installation Instructions We thank you for purchasing the Custom Dynamics Spyder TIPS units Our products utilize the latest technology and high quality components to ensure you the most reliable service We offer one of the best warranty pro grams in the industry and we back our products with excellent customer support if you have questions before or during installation of this product please call Custom Dynamics at 1 800 382 1388 Posi la TAP CONNECTOR Package Contents Tips Module Assembly 2 Harness Connector Female 2 gm i TAPS WIRES WITHOUT CUTTING he S h S Harness Connector Male 2 TOTAL WIRE INTEGRITY 1S MAINTAINED O Posi Tap Connector 2 REUSABLE OR PERMANENT Tighten LESS RESISTANCE Black 4 Tie Wrap 8 VIBRATION PROOF x FULLY INSULATED Strip Leads POWERS UP TO 4 LEADS AT ONCE Insert amp Tighten NO CRIMPING NO TOOLS NEEDED Assembled TIPS Unit plugs into stock connector located under A frame Bike Side Fits 2013 amp Up RS S ST S ST Limited RT S RT Limited Models Please see the specific instructions for your model when routing the turn signal wires Preparation Please take the time to verify the items in this kit and read the directions to fully to understand the installation The bike should be secured on a level surface while performing work Important Before work can begin on the RT Limited
6. nstall mirrors and body panels Questions Call us at 1 800 382 1388 M TH 8 30AM 5 30PM FR 9 30AM 5 30PM EST 07 2014SM Installation Instructions Page 4 RT S amp RT Limited Models With the blue wire routed up through the body into the upper nose area it must now be routed up to the turn sig nal area Using a wire guide tool will simplify this process a long flexible piece of wire or long zip tie will work well for fishing wire through the hard to reach places Tie wrap wires as need to prevent them from hanging or coming in contact with hot moving parts See photo below Make sure the factory mirror assemblies have been removed from the bike to allow access to the turn signal wires as noted on the first page If you have not please refer to a detailed service manual or your local Spyder service dealer for instructions on how to remove them With the mirror assembly removed pull the slack on the cable until the entire length of it is showing Your tap in point should be as close to the bike as possible to allow the posi Tap connections to fit back into the hole see photo on page 4 for reference You will need to strip the sheathing off the cable to allow tap in access to wire take care not to cut or fray wires while removing Once the turn signal wires are exposed test wires to determine which wire is the positive wire going to front turn signal We would normally tell you a color wire to attach to however we
Download Pdf Manuals
Related Search