Side Shift Carriage Manual (48" to 74")
Contents
1. E Ede 1 28 10 2 76826 M 1679 30 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 412644 ITEM QTY PART NO 1 1 32549 2 1 84923 3 1 32548 4 1 84928 5 2 3269 6 2 37839 7 1 3434 8 1 30259 9 1 88928 10 1 14071 1 1 14070 12 2 1043 2 1514 2 1503 13 1 14606 14 2 1089 2 1505 15 1 24506 16 1 24495 17 2 9371 18 1 19 1 4338 20 1 40151 21 4 24496 22 2 Varies 23 2 40149 DESCRIPTION Male Dust Cover Male Quick Coupler Female Dust Cover Female Quick Coupler Straight Connector 8MBo 6MJ Hose 38 X 50 6FJX 6FJX 90 Elbow 6MBo 6MJ 90 Elbow 6MBo 6MJ With 0 60 Orifice Cylinder Assembly Pin 1 00 x 3 31 Pin 1 00 x 4 72 38 UNC x 1 00 Hex Capscrew 38 Flat Washer 38 Lock Washer Pin Retainer 50 UNC x 1 25 Hex Capscrew 50 Lock Washer Side Shift Pin 2 00 x 49 50 Front Frame Grease Zerk Serial Number Identification Tag Location Made in USA Decal High Pressure Warning Decal Rear Frame Logo Pinch Point Danger Decal CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT 76826 M 1680 1 28 10 2 31 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 9 MADE IN USA M 1990 1 28 10 2 76826 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 9 ITEM QTY PARTNO DESCRIPTION 1 1 32548 Dust Cover 2 1 84928 Female Quick Coupler 3 1 32549 Dust Cover 4 1 84923 Male Quick Coupler 5 2 3269 Straight Conn2. INSTALLATION TOOL LARGE PRONG CYLINDER SMALL PRONG ROD SEAL cvunoen noo sea N 9 towards tool up roo SEAL 10356 5 14 76826 MAINTENANCE AND SERVICE Now insert the seal into the gland from the inner end Position the seal in man its groove and release and remove the tool Press the seal into its seat 4 wsrauanon root the rest of the way by hand Ba pem SIDE or CYLINDER ROO SEAL 2 Install the new piston ring rod wiper O rings and backup washers if ap plicable on the piston Be careful not to damage the seals Caution must be used when installing the piston ring The ring must be stretched carefully over the piston with a smooth round pointed tool TEFLON RING PISTON 3 After installing the rod seal inside the gland as shown in step 1 install the external seal N or FING NOTE Threaded glands may have been equipped with a separate O ring and backup washer system or a polypak all in one type seal Current seal kits con tain a polypak all in one type seal to replace the discarded seal types on ALL THREADED GLANDS 4 Slide the gland onto the cylinder rod being careful not to damage the rod YT 5 wiper Then install the spacer or flat washer if so equipped small piston and hex nut onto the end of the cylinder rod 5 Secure the cylinder rod mounting end in a vise with a supportatits center Torque the nutto the amount shown for th
3. Tighten all loose nuts capscrews and hydraulic connections Lubricate all grease fittings Coat the exposed portions of the cylinder rods with grease Connect the hydraulic couplers together to protect the hydraulic system from contami nates Touch up all unpainted and exposed areas with paint to prevent rust Replace decals if damaged or in unreadable condition Store the attachment in a dry and protected place with a cover if possible Leaving the attachment outside will materially shorten its life REMOVING FROM STORAGE ils 2 Remove all protective coverings Check hydraulic hoses for deterioration and replace if necessary M 1193 1 19 06 76826 Limited Warranty Except for the Excluded Products as described below all new products are warranted to be free from defects in material and or workmanship during the Warranty Period in accordance with and subject to the terms and conditions of this Limited Warranty 1 Excluded Products The following products are excluded from this Limited Warranty a Any cable part that engages with the ground i e sprockets digging chain bearing teeth tamping and or demolition head blade cutting edge pilot bit auger teeth and broom brush that either constitutes or is part of a product b Any product merchandise or component that in the opinion of Paladin Light Construction has been i misused ii modified in any unauthorized manner iii altered iv dama
4. 38 Flat Washer 11 2 9371 Grease Zerk 12 2 Varies Logo 13 2 40149 Decal Pinch Point 14 1 16842 Rear Frame 15 181 zen Serial Number Identification Tag Location 16 1 4338 Made in USA Decal 17 1 40151 High Pressure Warning Decal 18 4 16851 Side Shift Pin Retainer 19 1 14002 Fork Pin Retainer 20 8 1339 50 UNF x 1 25 Hex Capscrew 8 1505 50 Lock Washer 21 1 16841 Front Frame 22 1 16846 Side Shift Pin 2 00 x 48 25 23 1 19244 Fork Pin 2 00 x 49 00 CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1975 1 28 10 2 76826 25 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 83 FORK M 1668 1 28 10 2 76826 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 83 ITEM QTY PARTNO DESCRIPTION 1 1 32548 Dust Cover 2 1 84928 Female Quick Coupler 3 1 32549 Dust Cover 4 1 84923 Male Quick Coupler 5 2 3269 Straight Connector 8MBo 6MJ 6 2 37887 Hose 38 X 64 6FJX 6FJX 7 2 3297 Bulkhead Connector 6MJ 6MJ 8 2 37862 Hose 38 X 23 25 6FJX 6FJX90 9 1 3434 90 Elbow 6MBo 6MJ 10 al 88928 Cylinder Assembly 11 1 14067 90 Elbow W 027 Orifice 6MBo 6MJ 12 1 31990 Pin 1 00 x 4 50 13 14070 Pin 1 00 x 4 72 14 2 1293 38 UNF x 1 00 Hex Capscrew 2 1503 38 Lock Washer 2 1514 38 Flat Washer 15 2 9371 Grease Zerk 16 1 33530 Rear Frame 17 2 Varies Logo 18 2 40149 Decal Pinch Point 19 1 40151 High Pressure Warning Decal 20 1 4338 Made in USA Decal 21 Ieren Serial Number Ide
5. ASSEMBLY 0 FORK CARRIAGE 74 SIDE SHIFT DANGER 1 28 10 2 M 1982 76826 40 FORK CARRIAGE 74 SIDE SHIFT ASSEMBLY 411510 Straight Connector 12MBo 6MJ Hose 38 X40 6FJX 6FJX90 Bulkhead Straight Connector 6MJ 6MJ Hose 38 X 28 6FJX 6FJX Hose 38 X40 6FJX 6FJX 31 UNF x 1 00 Hex Capscrew 50 UNC x 1 50 Hex Capscrew Side Shift Pin 2 00 x 74 25 Serial Number Identification Tag Location 31 UNF x 1 00 Hex Capscrew High Pressure Warning Decal Pinch Point Danger Decal 75 UNC x 2 25 Hex Capscrew Grade 8 ITEM QTY PART NO DESCRIPTION 1 1 22519 Male Quick Coupler 2 1 22518 Female Quick Coupler 3 2 30201 4 2 37893 5 2 3297 6 1 37838 7 1 37492 8 2 3434 90 Elbow 6MBo 6MJ 9 1 88920 Cylinder Assembly 10 1 14071 Pin 1 00 x 3 31 11 1 100770 Pin 1 00 x 4 00 12 2 10023 2 1513 31 Flat Washer 13 1 32547 Right Pin Retainer 14 1 32470 Left Pin Retainer 15 6 1090 6 1505 50 Lock Washer 16 1 14780 17 1 14602 Fork Pin 60MM x 74 75 18 141 19 1 32468 Rear Frame 20 1 15007 Front Frame 21 1 81358 Hose Clamp 22 1 10023 1 1513 31 Flat Washer 23 2 Varies Logo 24 1 40151 25 1 4338 Made in USA Decal 26 2 40149 27 2 6133 Grease Zerk 28 2 14228 Stop Block 29 4 10012 4 1507 75 Lock Washer CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT 76826 M 1983 1 28 10 2 41 FORK CARR
6. 76826 1 FOREWORD Although Bradco has various side shift fork carriages available we are continually designing new sizes and mountings If your combination is not listed please contact the factory We have extensive mounting information available to generate the product you need Below is a listing of the side shift fork carriages that are currently available See the Parts section of this manual for the assemblies Shown DESCRIPTION amp MOUNT ASSEMBLY it CATERPILLAR 48 Side Shift Fork Carriage CAT IT TH 10 000 LB CAP 60MM SHAFT Shown 11324 74 Side Shift Fork Carriage CAT IT TH 10 000 LB CAP 60MM SHAFT Shown 11510 GEHL 66 Side Shift Fork Carriage GEHL DYNACARRIER Shown 12319 IR 48 Side Shift Fork Carriage IR VR518 VR623 6 000 LB CAP 2 SHAFT Shown 12426 JCB 48 Side Shift Fork Carriage JCB 10 000 LB CAP 2 1 4 SHAFT Shown 12633 48 Side Shift Fork Carriage JCB 520 5 500 LB CAP ITA CLASS Il Shown 12644 48 Side Shift Fork Carriage JCB 10 000 LB CAP ITA CLASS Shown 12659 JLG 48 Side Shift Fork Carriage JLG GRADALL C SERIES Shown 12966 74 Side Shift Fork Carriage JLG GRADALL C SERIES Shown 12965 MANITOU 60 Side Shift Fork Carriage MANITOU 10 000 LB CAP ITA CLASS III Shown 12703 NEW HOLLAND 48 Side Shift Fork Carriage NH 10 000 LB CAP 2 1 4 SHAFT Shown 12633 48 Side Shift Fo
7. connecting and disconnecting hydraulic hoses or fittings Keep unprotected body parts such as face eyes and arms as far away as possible from a suspected leak Flesh injected with hydraulic fluid may develop gangrene or other permanent disabilities If injured by injected fluid see a doctor at once If your doctor is not familiar with this type of injury ask him or her to research it immediately to determine proper treatment Wear safety glasses protective clothing and use a piece of cardboard or wood when searching for hydraulic leaks DO NOT USE YOUR HANDS SEE ILLUS TRATION CARDBOARD MAGNIFYING GLASS M 807 7 28 05 2 5 WARNING A WARNING A A GENERAL SAFETY PRECAUTIONS DO NOT MODIFY MACHINE OR ATTACHMENTS Modifications may weaken the integrity of the attachment and may impair the func tion safety life and performance of the attachment When making repairs use only the manufacturer s genuine parts following authorized instructions Other parts may be substandard in fit and quality Never modify any ROPS Roll Over Protection Structure or FOPS Falling Object Protective Structure equipment or device Any modifications must be authorized in writing by the manufacturer SAFELY MAINTAIN AND REPAIR EQUIPMENT Do not wear loose clothing or any accessories that can catch in moving parts If you have long hair cover or secure it so that it does not become entangled in the equipment Work on a l
8. mm Pounds Feet Newton Meters Pitch mm Pounds Feet Newton Meters 56 4979 6 86 10 79427 10 9 28136 2 2 55 95 18 1217 16323 ms 88 125 23 298 10 1927 257 366 10 9 271352 2231 298 42 56 271339 2028 271383 mo 88 15 46 1542 125 3547 474637 10 9 515423 4052 542 705 56 379 461 3141 42556 m2 88 1 75 69 1 79 9 125 56 68 759 921 10 9 772894 6275 84 101 6 56 664759 5264 705867 ma 88 20 109 8 126 15 90 106 1221436 10 9 130 1 147 7 107 124 145 168 56 90 8 1043 6583 335 1125 mis 88 20 15721762 15 120 138 162 6 187 10 9 1748 1965 140 158 189 7 214 1 56 119 2186 100 117 136 1585 mis 88 20 203 3 227 6 15 177 199 2399 2696 10 9 237 1 262 9 202 231 273 7 313 56 14631762 132 150 17892033 m20 88 25 2522778 15 206 242 279 1 327 9 10 9 213 249 288 6 337 4 246 289 333 3 391 6 10360 3 76826 17 STORAGE GENERAL INFORMATION The following storage procedure will help you to keep your attachment in top condition It will also help you get off to a good start the next time your equipment is needed We therefore strongly recommend that you take the extra time to follow these procedures whenever your attachment will not be used for an extended period of time PREPARATION FOR STORAGE a 2 Clean the attachment thoroughly removing all mua dirt and grease Inspect for visible signs of wear breakage or damage Order any parts required and make the necessary repairs to avoid delays when starting next season
9. 1 100770 Pin 1 00 x 4 00 2 10023 217 UNF x 1 00 Hex Capscrew 2 1502 217 Lock Washer 2 1513 31 Flat Washer 1 32547 Right Pin Retainer 1 32470 Left Pin Retainer 6 1090 50 UNC x 1 50 Hex Capscrew 6 1505 50 Lock Washer 1 32493 Side Shift Pin 2 00 x 47 75 1 14262 Fork Pin 60MM x 48 50 1 0 Serial Number Identification Tag Location 1 107318 Rear Frame 1 32469 Front Frame 1 40151 High Pressure Warning Decal 1 4338 Made in USA Decal 2 Varies Logo 2 40149 Pinch Point Danger Decal 2 6133 Grease Zerk CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1987 1 28 10 2 35 FORK CARRIAGE 60 SIDE SHIFT ASSEMBLY 12703 A DANGER gt 18 MAD IN USA M 1144 1 28 10 3 76826 FORK CARRIAGE 60 SIDE SHIFT ASSEMBLY 12703 ITEM QTY PART NO DESCRIPTION 1 2 32548 Dust Cover 2 2 84928 Female Quick Coupler 3 2 3269 Straight Connector 8MBo 6MJ 4 2 37887 Hose 38 X 64 6FJX 6FJX 5 2 3297 Bulkhead Connector 6MJ 6MJ 6 2 37862 Hose 38 X 23 25 6FJX 6FJX90 T 1 3434 90 Elbow 6MBo 6MJ 8 1 88928 Cylinder Assembly 9 1 14067 90 Elbow W 027 Orifice 6MBo 6MJ 10 1 12054 Pin 1 00 x 3 75 11 1 31990 Pin 1 00 x 4 50 12 2 1293 38 UNF x 1 00 Hex Capscrew 2 1503 38 Lock Washer 2 1514 38 Flat Washer 13 2 9371 Grease Zerk 14 1 102014 Rear Frame 15 2 Varies Logo 16 2 40149 Decal Pinch Point 17 1 40151 High Pressure Warning Decal 18 1 4338 Made in USA Decal 19 181 0 Ser
10. BRADCO OPERATOR S amp PARTS 565565 MANUAL 46 85 48 74 SIDE SHIFT Ar online tt FORK CARRIAGE SERIAL NUMBER Manual Number 76826 Part Number 76826 MODEL NUMBER Rev 2 January 28 2010 800 456 7100 www paladinicg com 503 Gay Street Delhi 52223 United States of America M 2000 1 26 10 2 TABLE OF CONTENTS FOREWORD PREFACE SAFETY PRECAUTIONS SAFETY STATEMENTS GENERAL SAFETY PRECAUTIONS EQUIPMENT SAFETY PRECAUTIONS INSTALLATION AND OPERATION eren ATTACHING AND DETACHING SIDE SHIFT FORK CARRIAGE OPERATING SIDE SHIFT FORK CARRIAGE TROUBLESHOOTING MAINTENANCE AND SERVICE GENERAL INFORMATION DAILY EVERY 40 HOURS CYLINDER SEAL REPLACEMENT SPECIFICATIONS BOLT TORQUE STORAGE LIMITED WARRANTY PARTS SIDE SHIFT FORK CARRIAGES 48 SIDE SHIFT FORK CARRIAGE ASSEMBLY 4 48 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12426 48 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12633 48 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12540 48 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12644 48 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12659 48 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12966 60 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12703 66 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12319 74 SIDE SHIFT FORK CARRIAGE ASSEMBLY 11510 74 SIDE SHIFT FORK CARRIAGE ASSEMBLY 12985 CYLINDERS CYLINDER ASSEMBLY 88920 CYLINDER ASSEMBLY 88928 M 1994 7 30 08
11. Decal 75 UNC x 2 25 Hex Capscrew Grade 8 ITEM QTY PART NO DESCRIPTION 1 1 22519 Male Quick Coupler 2 1 22518 Female Quick Coupler 3 2 30201 4 2 37893 5 2 3297 6 1 37838 7 1 37492 8 2 3434 90 Elbow 6MBo 6MJ 9 1 88920 Cylinder Assembly 10 1 14071 Pin 1 00 x 3 31 11 1 100770 Pin 1 00 x 4 00 12 2 10023 2 1513 31 Flat Washer 13 1 32547 Right Pin Retainer 14 1 32470 Left Pin Retainer 15 6 1090 6 1505 50 Lock Washer 16 1 32493 17 1 14262 Fork Pin 60MM x 48 50 18 1 1 19 1 32468 Rear Frame 20 1 32469 Front Frame 21 1 81358 Hose Clamp 22 1 10023 1 1513 31 Flat Washer 23 2 Varies Logo 24 1 40151 25 1 4338 Made in USA Decal 26 2 40149 27 2 6133 Grease Zerk 28 2 14228 Stop Block 29 4 10012 4 1507 75 Lock Washer CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT 76826 M 1667 1 28 10 2 23 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 12426 DANGER i ay MADE INUSA M 1974 1 28 10 2 76826 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 12426 ITEM QTY PARTNO DESCRIPTION 1 d 22518 Female Quick Coupler 2 d 22519 Male Quick Coupler 3 2 30201 Straight Connector 12MBo 6MJ 4 2 14397 Hose 38 X 69 6FJX 6FJX 5 1 3434 90 Elbow 6MBo 6MJ 6 1 14067 90 Elbow W 027 Orifice 6MBo 6MJ 7 1 88928 Cylinder Assembly 8 1 14071 Pin 1 00 x 3 31 9 1 14070 Pin 1 00 x 4 72 10 2 1293 38 UNF x 1 00 Hex Capscrew 2 1503 38 Lock Washer 2 1514
12. IAGE 74 SIDE SHIFT ASSEMBLY 12965 12 13 14 15 76826 FORK CARRIAGE 74 SIDE SHIFT ASSEMBLY 412965 QTY PART NO DESCRIPTION 1 51753 Dust Cap 1 15109 Male Quick Coupler 1 51754 Dust Plug 1 15110 Female Quick Coupler 2 3125 Straight Connector 6MJ 8MP 2 37839 Hose 38 X 50 6FJX 6FJX 2 3434 90 Elbow 6MBo 6MJ 1 88920 Cylinder Assembly 1 14071 Pin 1 00 x 3 31 1 100770 Pin 1 00 x 4 00 2 10023 217 UNF x 1 00 Hex Capscrew 2 1502 217 Lock Washer 2 1513 31 Flat Washer 1 32547 Right Pin Retainer 1 32470 Left Pin Retainer 6 1090 50 UNC x 1 50 Hex Capscrew 6 1505 50 Lock Washer 1 14780 Side Shift Pin 2 00 x 74 25 1 14602 Fork Pin 60MM x 74 75 1 7 0 Serial Number Identification Tag Location 1 107318 Rear Frame 1 15007 Front Frame 1 40151 High Pressure Warning Decal 1 4338 Made in USA Decal 2 Varies Logo 2 40149 Pinch Point Danger Decal 2 6133 Grease Zerk CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1989 1 28 10 2 43 CYLINDER ASSEMBLY ASSEMBLY 88920 M 664 10 15 07 2 76826 CYLINDER ASSEMBLY ITEM QTY PARTNO 1 1 89112 2 2 88919 8 1 1488 4 1 4644 5 1 4645 6 1 50252 7 1 4641 8 1 5421 9 1 4509 10 1 4510 11 1 45250 12 1 77458 13 1 45219 14 1 45389 15 1 88915 16 1 88918 17 1 6616 ASSEMBLY 488920 DESCRIPTION Cylinder Tube With Valve Bronze Bushing Hex Nut Piston Ring O Ring Piston O Ring
13. LAND 1 Rotate the gland with a spanner wrench counterclockwise until the gland is free of the cylinder tube 2 Pul the cylinder rod from the cylinder tube and inspect the piston and the bore of the cylinder tube for deep scratches or galling If damaged the piston AND the cylinder tube must be replaced Span wienn INSPECT TUBE NS eh GLAND PS spect 3 Remove the hex nut piston fiat washer or spacer tube if so equipped and gland from the cylinder rod If the cylinder rod is rusty scratched or bent it must be replaced 4 Remove and discard all the old seals DISCARD aam Piston Hex Nur ES WASHER ASSEMBLY PROCEDURE IMPORTANT Replace all seals even if they do not appear to be damaged Failure to replace all seals may result in premature cylinder failure NOTE Seal kits will service most cylinders of similar bore size and rod diameter 1 Install the cylinder rod seal in the gland first Be careful not to damage the seal in the process as it is somewhat difficult to install NOTE A special installation tool Part 65349 is available to help with installing the seal Simply fit the end of the tool over the seal so that the large prong of the tool is on the outside of the seal and the two smaller prongs on the inside The lip of the seal should be facing towards the tool Rotate the handles on the tool around to wrap the seal around the end of the tool END view
14. NJURY OR DEATH WILL RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY A WARNING THIS SIGNAL WORD IS USED WHERE SERIOUS INJURY OR DEATH COULD RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY A CAUTION THIS SIGNAL WORD IS USED WHERE MINOR INJURY COULD RESULT IF NOTICE WARNING INSTRUCTIONS ARE NOT FOLLOWED PROPERLY NOTICE INDICATES A PROPERTY DAMAGE MESSAGE GENERAL SAFETY PRECAUTIONS READ MANUAL PRIOR TO INSTALLATION Improper installation operation or maintenance of this equipment could result in se rious injury or death Operators and maintenance personnel should read this manual as well as all manuals related to this equipment and the prime mover thoroughly before beginning installation operation or maintenance FOLLOW ALL SAFETY INSTRUCTIONS IN THIS MANUAL AND THE PRIME MOVER S MANUAL S READ AND UNDERSTAND ALL SAFETY STATEMENTS Read all safety decals and safety statements in all manuals prior to operating or working on this equipment Know and obey all OSHA regulations local laws and other professional guidelines for your operation Know and follow good work prac tices when assembling maintaining repairing mounting removing or operating this equipment KNOW YOUR EQUIPMENT Know your equipment s capabilities dimensions and operations before operating Visually inspect your equipment before you start and never operate equipment that is not in proper working order with
15. Shipping Weight Without Forks Ibs 690 876 947 12426 12540 12633 Overall Height inches Without Forks 44 49 38 40 43 87 Overall Width inches 46 75 49 25 51 00 Side Shift on Each Side of Center inches 4 00 4 00 4 00 Total Overall Side Shift Movement inches 8 00 8 00 8 00 Attachment Weight Without Forks Ibs 683 604 680 Shipping Weight Without Forks Ibs 733 654 730 12644 12659 12703 Overall Height inches Without Forks 49 80 44 83 44 80 Overall Width inches 49 51 51 00 59 00 Side Shift on Each Side of Center inches 4 00 4 00 4 00 Total Overall Side Shift Movement inches 8 00 8 00 8 00 Attachment Weight Without Forks Ibs 590 963 1052 Shipping Weight Without Forks Ibs 640 1018 1102 12966 12965 Overall Height inches Without Forks 45 25 45 25 Overall Width inches 49 00 75 50 Side Shift on Each Side of Center inches 4 00 4 00 Total Overall Side Shift Movement inches 8 00 8 00 Attachment Weight Without Forks Ibs 710 826 Shipping Weight Without Forks Ibs 760 876 M 2001 4 21 08 76826 BOLT TORQUE SPECIFICATIONS GENERAL TORQUE SPECIFICATION TABLES Use the following charts when determining bolt torque specifications when special torques are not given Always use grade 5 or better when replacing bolts SAE BOLT TORQUE SPECIFICATIONS NOTE The following torque values are for use with extreme pressure lubricants plating or hard washer applications Increase torque 15 when using hardware that is u
16. Washer O Ring Back Up Washer O Ring Cylinder Gland Poly Pak Seal Rod Wiper Piston Rod Bronze Bushing Grease Zerk NOTE Seal Kit 445617 includes all parts marked with an asterisk Parts are not sold separately T6826 M 665 10 15 07 2 45 CYLINDER ASSEMBLY ASSEMBLY 88928 M 1029 9 13 05 76826 CYLINDER ASSEMBLY ASSEMBLY 488928 ITEM QTY PARTNO DESCRIPTION 1 1 88926 Cylinder Tube 2 2 88919 Bronze Bushing 3 1 1483 Hex Nut 4 1 4644 Piston Ring 5 1 4645 O Ring 6 1 50252 Piston 7 1 4641 O Ring 8 1 5421 Washer 9 1 4509 O Ring 10 1 4510 Back Up Washer 11 1 45250 O Ring 12 1 77458 Oylinder Gland 13 1 45219 Poly Pak Seal 14 1 45389 Rod Wiper 15 1 88927 Cylinder Rod 16 1 88918 Bronze Bushing 17 2 6616 Grease Zerk NOTE Seal Kit 445617 includes all parts marked with an asterisk Parts are not sold separately T6826 M 1030 8 15 05 47 48 BRADCO PALADIN LIGHT CONSTRUCTION 503 Gay Street Delhi 52223 563 922 2981 800 456 7100 www paladinlcg com M 1360 1 26 10 2 76826
17. all safety devices intact Check all hardware to ensure it is tight Make certain that all locking pins latches and connection devices are properly installed and secured Remove and replace any damaged fatigued or excessively worn parts Make certain all safety decals are in place and are legible Keep decals clean and replace them if they become worn or hard to read M 806 7 28 05 2 76826 WARNING WARNING WARNING A HYDRAULIC HOSE OR FITTING T6826 GENERAL SAFETY PRECAUTIONS PROTECT AGAINST FLYING DEBRIS Always wear proper safety glasses goggles or a face shield when driving pins in or out or when any operation causes dust flying debris or any other hazardous mate rial LOWER OR SUPPORT RAISED EQUIPMENT Do not work under raised booms without supporting them Do not use support mate rial made of concrete blocks logs buckets barrels or any other material that could suddenly collapse or shift positions Make sure support material is solid not de cayed warped twisted or tapered Lower booms to ground level or on blocks Lower booms and attachments to the ground before leaving the cab or operator s station USE CARE WITH HYDRAULIC FLUID PRESSURE Hydraulic fluid under pressure can penetrate the skin and cause serious injury or death Hydraulic leaks under pressure may not be visible Before connecting or dis connecting hydraulic hoses read your prime mover s operator s manual for detailed instructions on
18. allow Paladin Light Construction to inspect the part or product Claims that fail to comply with any of the above terms and conditions shall be denied LIMITATIONS AND EXCLUSIONS THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY BASED ON A COURSE OF DEALING OR USAGE OF TRADE IN NO EVENT SHALL PALADIN LIGHT CONSTRUCTION BE LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES IN NO EVENT SHALL PALADIN LIGHT CONSTRUCTION BE LIABLE FOR ANY LOSS OR CLAIM IN AN AMOUNT IN EXCESS OF THE PURCHASE PRICE OR AT THE OPTION OF PALADIN LIGHT CONSTRUCTION THE REPAIR OR REPLACEMENT OF THE PARTICULAR PRODUCT ON WHICH ANY CLAIM OF LOSS OR DAMAGE IS BASED THIS LIMITATION OF LIABILITY APPLIES IRRESPECTIVE OF WHETHER THE CLAIM IS BASED ON BREACH OF CONTRACT BREACH OF WARRANTY NEGLIGENCE OR OTHER CAUSE AND WHETHER THE ALLEGED DEFECT IS DISCOVERABLE OR LATENT Attachment Technologies Inc a subsidiary of Paladin Brands Holding Inc PBHI is referred to herein as Paladin Light Construction February 10 2010 76826 19 THIS PAGE IS INTENTIONALLY BLANK 76826 PARTS The following section contains detailed diagrams and parts lists which include your attachment Please use these diagrams and parts lists to locate replacement parts prior to contacting the parts department When servicing your attachment reme
19. d if necessary personal protective equipment during the operation of any attachment that may cause high levels of dust TRANSPORTING THE SIDE SHIFT FORK CARRIAGE Travel only with the attachment in a safe transport position to prevent uncon trolled movement Drive slowly over rough ground and on slopes When driving on public roads use safety lights reflectors Slow Moving Vehicle signs etc to prevent accidents Check local government regulations that may affect you Do not drive close to ditches excavations etc as a cave in could result Do not smoke wen refueling the prime mover Allow room in the fuel tank for ex pansion Wipe up any spilled fuel and secure cap tightly when done MAINTAINING THE SIDE SHIFT FORK CARRIAGE Before performing maintenance lower the attachment to the ground apply the brakes turn off the engine and remove the key Never perform any work on the equipment unless you are authorized and qualified to do so Always read the operator s and service manual s before any repair is made After completing maintenance or repair check for correct func tioning of the attachment If not functioning properly always attach a DO NOT OPERATE tag to the machine until all problems are corrected Worn damaged or illegible safety decals must be replaced New safety decals can be ordered from the manufacturer Never make hydraulic repairs while the system is under pressure Serious personal injury or dea
20. ds can fall unexpectedly When transporting a load keep the forks as close to the ground as possible Keep the lifting surface of the forks level at all times Do not handle round bales with fork lift tines Don t obstruct your vision when traveling or working Carry the forks low for maxi mum stability and visibility When using the side shift feature to pick up a load be sure to return the forks and load to the center position as soon as possible Do NOT travel with loaded forks shifted to the side If the carriage tilts or drifts due to oil leakage within the cylinder assembly discon tinue use until the problem has been corrected Reduce speed when driving over rough terrain on a slope or turning to avoid overturning the vehicle Never use the attachment for a work platform or personnel carrier An operator must not use drugs or alcohol which can change his or her alertness or coordination An operator taking prescription or over the counter drugs should seek medical advice on whether or not he or she can safely operate equipment Before exiting the prime mover lower the attachment to the ground apply the brakes turn off the prime mover s engine and remove the key M 1997 4 21 08 7 EQUIPMENT SAFETY PRECAUTIONS EXPOSURE TO RESPIRABLE CRYSTALLINE SILICA DUST ALONG WITH OTHER HAZARDOUS DUSTS MAY CAUSE SERIOUS OR FATAL RESPIRA TORY DISEASE It is recommended to use dust suppression dust collection an
21. e thread diameter of the cylinder oe rod see chart Thread Diameter POUNDS FEET 7 8 150 200 Ar 230 325 1 1 8 350 480 1 1 4 490 670 1 3 8 670 900 1 Thread Diameter WITH 1 25 Rod Diameter Min 230 ft lbs 250 ft Ibs IMPORTANT Do not contact the active surface of the cylinder rod with the vise Damage to the rod could result 6 Apply lubricant such as Lubriplate 105 to the piston and tefion ring Insert the cylinder rod assembly into the cylinder tube IMPORTANT Ensure that the piston ring fits squarely into the cylinder tube and piston groove otherwise the ring may be damaged and a leak will occur 7 Use a spanner wrench to rotate the gland clockwise into the cylinder Continue to rotate the gland with the spanner wrench until itis tight WARNING Cylinders serviced in the field are to be tested for leakage prior to the attachment being placed in work Failure to test rebuilt cylinders could result in damage to the cylinder and or A the attachment cause severe personal injury or even death 10357 10 13 05 76826 15 SPECIFICATIONS SIDE SHIFT FORK CARRIAGE SPECIFICATIONS 11324 11510 12319 Overall Height inches Without Forks 40 50 45 25 39 38 Overall Width inches 49 00 75 50 67 78 Side Shift on Each Side of Center inches 4 00 4 00 4 00 Total Overall Side Shift Movement inches 8 00 8 00 8 00 Attachment Weight Without Forks Ibs 640 826 897
22. ector 8MBo 6MJ 6 2 37887 Hose 38 X 64 6FJX 6FJX 7 2 3297 Bulkhead Connector 6MJ 6MJ 8 2 37862 Hose 38 X 23 25 6FJX 6FJX90 9 1 3434 90 Elbow 6MBo 6MJ 10 al 88928 Cylinder Assembly 11 1 14067 90 Elbow W 027 Orifice 6MBo 6MJ 12 1 31990 Pin 1 00 x 4 50 13 12054 Pin 1 00 x 3 75 14 2 1293 38 UNF x 1 00 Hex Capscrew 2 1503 38 Lock Washer 2 1514 38 Flat Washer 15 2 9371 Grease Zerk 16 1 33530 Rear Frame 17 2 Varies Logo 18 2 40149 Pinch Point Decal 19 1 40151 High Pressure Warning Decal 20 181 Serial Number Identification Tag Location 21 1 4338 Made in USA Decal 22 1 33549 Side Shift Pin 2 00 x 53 00 23 1 33541 Pin Retainer 24 2 1339 50 UNF x 1 25 Hex Capscrew 2 1505 50 Lock Washer 2 1516 50 Flat Washer 25 1 100974 Front Frame 26 1 1089 50 UNC x 1 25 Hex Capscrew 1 86149 Spacer 1 1228 50 UNC Hex Nut CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1991 1 28 10 2 76826 33 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 12966 n gt gD M 1986 1 28 10 2 34 76826 12 13 14 15 76826 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 412966 QTY PART NO DESCRIPTION 1 51753 Dust Cap 1 15109 Male Quick Coupler 1 51754 Dust Plug 1 15110 Female Quick Coupler 2 3125 Straight Connector 6MJ 8MP 2 37839 Hose 38 X 50 6FJX 6FJX 2 3434 90 Elbow 6MBo 6MJ 1 88920 Cylinder Assembly 1 14071 Pin 1 00 x 3 31
23. elop gangrene or other permanent disabilities If injured by injected fluid see a doctor at once If your doctor is not familiar with this type of injury ask him or her to research it immediately to determine proper treatment CARDBOARD HYDRAULIC HOSE OR FITTING IMPORTANT When replacing parts use only factory approved replacement parts Manu facturer will not claim responsibility for use of unapproved parts or accessories and or other damages as a result of their use EVERY 40 HOURS Lubrication is an important part of maintenance It is recommended that all grease fittings be lubricated after the intitial 8 hours of operation and then after every 40 hours of use M 852 5 27 05 1 76826 8 MAINTENANCE AND SERVICE CYLINDER SEAL REPLACEMENT The following information is provided to assist you in the event you should need to repair or rebuild a hy draulic cylinder When working on hydraulic cylinders make sure that the work area and tools are clean and free of dirt to prevent contamination of the hydraulic system and damage to the hydraulic cylinders Always protect the active part of the cylinder rod the chrome section Nicks or scratches on the surface of the rod could result in cylinder failure Clean all parts thoroughly with a cleaning solvent before reassembly DISASSEMBLY PROCEDURE IMPORTANT Do not contact the active surface of the cylinder rod with the vise Damage to the rod could result THREADED TYPE G
24. evel surface in a well lit area Use properly grounded electrical outlets and tools Usethe correct tools for the job at hand Make sure they are in good condition for the task required Wear the protective equipment specified by the tool manufacturer SAFELY OPERATE EQUIPMENT Do not operate equipment until you are completely trained by a qualified operator in how to use the controls know its capabilities dimensions and all safety require ments See your machine s manual for these instructions Keep all step plates grab bars pedals and controls free of dirt grease debris and oil Never allow anyone to be around the equipment when it is operating Do not allow riders on the attachment or the prime mover Do not operate the equipment from anywhere other than the correct operator s position Never leave equipment unattended with the engine running or with this attach ment in a raised position Do not alter or remove any safety feature from the prime mover or this attach ment Know your work site safety rules as well as traffic rules and flow When in doubt on any safety issue contact your supervisor or safety coordinator for an explana tion M 808 7 28 05 2 76826 WARNING A 76826 EQUIPMENT SAFETY PRECAUTIONS KNOW WHERE UTILITIES ARE Observe overhead electrical and other utility lines Be sure equipment will clear them When digging call your local utilities for location of bu
25. ged v involved in an accident or vi repaired using parts not obtained through Paladin Light Construction 2 Warranty Period The Limited Warranty is provided only to those defects that occur during the Warranty Period which is the period that begins on the first to occur of i the date of initial purchase by an end user ii the date the product is first leased or rented or iii the date that is six 6 months after the date of shipment by Paladin Light Construction as evidenced by the invoiced shipment date the Commencement Date and ends on the date that is twelve 12 months after the Commencement Date 3 Terms and Conditions of Limited Warranty The following terms and conditions apply to the Limited Warranty hereby provided a Option to Repair or Replace Paladin Light Construction shall have the option to repair or replace the product b Timely Repair and Notice In order to obtain the Limited Warranty i the product must be repaired within thirty 30 days from the date of failure and ii a claim under the warranty must be submitted to Paladin Light Construction in writing within thirty 30 days from the date of repair c Retum of Defective Part or Product If requested by Paladin Light Construction the alleged defective part or product shall be shipped to Paladin Light Construction at its manufacturing facility or other location specified by Paladin Light Construction with freight PRE PAID by the claimant to
26. h hoses on one cylinder ing carriage does not shift connected 2 Insufficient hydraulic flow from Refer to your vehicle operator s manual the prime mover 3 Cylinder rod bent Visually inspect the cylinder for damage 4 Oylinder seals damaged Replace cylinder seals 5 Obstruction in hydraulic lines Remove obstruction and replace if necessary 76826 M 1995 4 17 08 11 THIS PAGE IS INTENTIONALLY BLANK 76826 MAINTENANCE amp SERVICE GENERAL INFORMATION Regular maintenance is the key to long equipment life and safe operation Maintenance requirements have been kept to an absolute minimum However it is very important that these maintenance functions be performed as described in this section DAILY H Check all bolts and nuts for tightness Replace any missing bolts or nuts with approved replacement parts Check hydraulic system for hydraulic oil leaks See procedure below Visually inspect the machine for worn parts or cracked welds and repair as necessary WARNING Escaping fluid under pressure can have sufficient force to penetrate the Skin causing serious personal injury Fluid escaping from a very small A hole can be almost invisible Use a piece of cardboard or wood rather than hands to search for suspected leaks Keep unprotected body parts such as face eyes and arms as far away as possible from a suspected leak Flesh injected with hydraulic fluid may dev
27. hould be closest to the fork frame and not near the tips of the fork tines 2 Before lifting make certain the fork tines are completely under the load and level 3 Lift the load slightly to make sure the load is stable If the load appears unstable lower and reposition the tines to achieve full stability Raise the telehandler to the MINIMUM height required for the terrain During material handling keep the fork tines level stop and start the telehandler gradually slow down before turning avoid obstacles bumps or holes 6 Check the load frequently to ensure stability WARNING Never exceed the recommended lifting capacity of any approved fork tines H or the prime mover NOTE Fork tine capacities are pounds per pair at a 24 load center The center of gravity of the allowable loads must be applied within the first 24 of the fork tines when measured from the front face of the vertical section of the fork tine out toward the tip of the horizontal section of the fork tine WARNING EXPOSURE TO RESPIRABLE CRYSTALLINE SILICA DUST ALONG WITH OTHER HAZARDOUS DUSTS MAY CAUSE SERIOUS OR FATAL RESPIRA A TORY DISEASE It is recommended to use dust suppression dust collection and if neces sary personal protective equipment during the operation of any attachment that may cause high levels of dust IMPORTANT Concrete and masonry products contain silica sand Quartz which is a form of silica and the most common mine
28. ial Number Identification Tag Location 20 1 33541 Pin Retainer 21 2 1339 50 UNF x 1 25 Hex Capscrew 2 1505 50 Lock Washer 2 1516 50 Flat Washer 22 1 102015 Front Frame 23 1 1089 50 UNC x 1 25 Hex Capscrew 1 86149 Spacer 1 1228 50 UNC Hex Nut 24 1 111597 Fork Pin 2 00 x 61 00 CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1145 1 28 10 3 76826 37 FORK CARRIAGE 66 SIDE SHIFT ASSEMBLY 12319 MADE IN USA M 1992 1 28 10 2 76826 FORK CARRIAGE 66 SIDE SHIFT ASSEMBLY 9 ITEM QTY PART NO DESCRIPTION 1 1 22518 Female Quick Coupler 2 1 22519 Male Quick Coupler 3 2 30201 Straight Connector 12MBo 6MJ 4 2 37886 Hose 38 X 60 6FJX 6FJX 5 2 3434 90 Elbow 6MBo 6MJ 6 1 88928 Cylinder Assembly 7 1 14071 Pin 1 00 x 3 31 8 1 14070 Pin 1 00 x 4 72 9 2 1293 38 UNF x 1 00 Hex Capscrew 2 1503 38 Lock Washer 2 1514 38 Flat Washer 10 1 33020 Rear Frame 11 2 Varies Logo 12 2 40149 Decal Pinch Point 43 1 40151 High Pressure Warning Decal 14 1 4338 Made in USA Decal 15 MEE Serial Number Identification Tag Location 16 1 14002 Fork Pin Retainer 17 4 1339 50 UNF x 1 25 Hex Capscrew 4 1505 50 Lock Washer 4 1516 50 Flat Washer 18 1 33011 Front Frame 19 1 14606 Side Shift Pin Retainer 20 1 33027 Side Shift Pin 2 00 x 66 00 21 1 33199 Fork Pin 2 00 x 66 75 CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1993 1 28 10 2 76826 39
29. mber to use only original manufacturer replace ment parts Substitute parts may not meet the standards required for safe dependable opera tion To facilitate parts ordering have the model and serial number of your product ready to ensure that you receive the correct parts for your specific attachment The model and serial number for your attachment should be recorded in the space provided on the cover of this manual This information may be obtained from the serial number identification plate located on your attachment See the parts diagram for your attachment for the location NOTE Most daily and emergency orders received by 2 00 P M will be shipped the same day received with Emergency Machine Down orders receiving first priority wa BRADCO PALADIN LIGHT CONSTRUCTION PARTS DEPARTMENT 734 996 9116 800 456 7100 We Encourage Fax Orders 734 996 9014 M 1127 1 26 10 3 76826 21 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 11324 M 1666 1 28 10 2 22 76826 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 11324 Straight Connector 12MBo 6MJ Hose 38 X40 6FJX 6FJX90 Bulkhead Straight Connector 6MJ 6MJ Hose 38 X 28 6FJX 6FJX Hose 38 X40 6FJX 6FJX 31 UNF x 1 00 Hex Capscrew 50 UNC x 1 50 Hex Capscrew Side Shift Pin 2 00 x 47 75 Serial Number Identification Tag Location 31 UNF x 1 00 Hex Capscrew High Pressure Warning Decal Pinch Point Danger
30. nplated and either dry or lubricated with engine oil SAE GRADES TORQUE SAE GRADE 8 TORQUE Bolt head identification marks as per Bolt Size Pounds Feet Newton Meters Pounds Feet Newton Meters grade NOTE Manufacturing Marks Will Vary 16865 Milimeters UNC UNF UNG UNF UNC UNF UNG UNE 14 655 8 3 3 819 81 8 18 16 794 18 8 mo 5 Z 34 35 855 a e a o 59 su 32 ap mi 6 a A 36 12 gt m2 187 16 96 14 29 94 112 127 152 136 163 184 221 GRADES 58 3588 128163 4 27 ter 224 294 304 34 3805 230 25 sn 373 su 395 48 ss 78 2223 59 as as 510 6 2 69 830 2546 as 552 865 862 765 8 12 GRADE 8 2558 650 748 sz2 1814 10881224 i47 156 52 1054 11 157 1700 267 256 2483 1241 1428 1683 1525 2028 2912 27033135 3810 1649 1870 2236 2535 2686 3026 3642 4103 METRIC BOLT TORQUE SPECIFICATIONS NOTE The following torque values are for use with metric Bolt head identification marks as per grade hardware that is unplated and either dry or lubricated with 55 9 engine oil Reduce torque 1536 when using hardware that has extreme pressure lubricants plating or hard washer applications Size of Bolt Grade No Pitch
31. ntification Tag Location 22 1 33554 Pin Retainer 23 3 1339 50 UNF x 1 25 Hex Capscrew 3 1505 50 Lock Washer 3 1516 50 Flat Washer 24 1 33531 Front Frame 25 1 33549 Side Shift Pin 2 00 x 53 00 26 1 33550 Fork Pin 2 25 x 53 50 CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1669 1 28 10 2 76826 27 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 0 Ed 76826 12 18 14 15 76826 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 412540 YN PART NO 22519 22518 30201 35424 3297 38036 3434 88920 14071 31990 10023 1513 32547 32470 1090 1505 32493 104880 BE STEE DESCRIPTION Male Quick Coupler Female Quick Coupler Straight Connector 12MBo 6MJ Hose 38 X 76 6FJX 6FJX Bulkhead Straight Connector 6MJ 6MJ Hose 38 X15 6FJX 6FJX 90 Elbow 6MBo 6MJ Oylinder Assembly Pin 1 00 x 3 31 Pin 1 00 x 4 50 31 UNF x 1 00 Hex Capscrew 317 Flat Washer Right Pin Retainer Left Pin Retainer 50 UNC x 1 50 Hex Capscrew 50 Lock Washer Side Shift Pin 2 00 x 47 75 Fork Pin 2 25 x 48 38 Serial Number Identification Tag Location Rear Frame Front Frame High Pressure Warning Decal Made in USA Decal Pinch Point Danger Decal Grease Zerk CONTACT YOUR DEALER FOR TINES AVAILABLE FOR YOUR ATTACHMENT M 1985 7 30 08 29 FORK CARRIAGE 48 SIDE SHIFT ASSEMBLY 412644
32. ral in the earths crust is associated with many types of rock Some activities that silica dust may be present in the air include demolition sweeping loading sawing hammering drilling or planing of rock concrete or masonry It is recommended to use dust suppression such as water dust collection such as a vacuum along with personal protective equipment if necessary during the operation of any attachment that may cause high levels of silica dust M 1931 8 10 76826 INSTALLATION AND OPERATION TROUBLESHOOTING ATTACHMENTS WITH HYDRAULICS PROBLEM POSSIBLE CAUSE POSSIBLE REMEDY Excessive oil temperature 1 Hydraulic oil level too low Refer to your vehicle operator s manual 2 Obstruction in hydraulic lines Remove obstruction and replace if necessary 3 Couplers not engaged correctly Engage couplers 4 Hydraulic system overloaded and system relief open Reduce load A Hydraulic cylinder not operating 1 Insufficient hydraulic flow from the prime mover Refer to your vehicle operator s manual 2 Cylinder rod bent Visually inspect the cylinder for damage 3 Cylinder seals damaged Replace cylinder seals 4 Obstruction in hydraulic lines Remove obstruction and replace if necessary SIDE SHIFT FORK CARRIAGES PROBLEM POSSIBLE CAUSE POSSIBLE REMEDY Hydraulic cylinder not operat 1 Hydraulic hoses incorrectly Switc
33. ried utility lines gas water and sewer as well as any other hazard you may encounter OPERATING THE PRIME MOVER Avoid steep hillside operation which could cause the prime mover to overturn Consult your machine operator s and safety manuals for maximum incline allowable When operating on a slope keep the load low and proceed with extreme caution Do not drive ACROSS a steep slope drive straight up and down With a LOADED attachment face the attachment and load uphill With an EMPTY attachment face the attachment downhill OPERATING THE SIDE SHIFT FORK CARRIAGE Do not exceed the lifting capacity of your prime mover and attachment Always observe lift capacity limits listed in machine specifications or on load charts fur nished with the prime mover Always space the forks correctly for the load Loads can fall off incorrectly spaced forks Make sure the forks are completely under the load before lifting Be careful when handling large loose objects Lifting too high or rolling forks too far back could result in these objects falling back on the operator Unsecured loads can cause vehicle tipover which can result in serious injury or death Do not use the fork tines for prying or any purpose other than lifting Never stack loads on uneven ground Loads stacked on uneven ground can topple Never lift a load with one fork A load lifted with one fork can slip off and cause injury Secure loads properly Unsecured loa
34. rk Carriage NH VERSATTACH 10 000 LB CAP ITA CLASS Shown 12659 TEREX 48 Side Shift Fork Carriage TEREX TX51 19 TEREX HITCH Shown 12540 M 1999 1 28 10 2 76826 PREFACE GENERAL COMMENTS Congratulations on the purchase of your new attachment This product was carefully designed and manufactured to give you many years of dependable service Only minor maintenance such as cleaning and lubricating is required to keep it in top working condition Be sure to observe all maintenance procedures and safety precautions in this manual and on any safety decals located on the product and on any equipment on which the attachment is mounted Also check load charts before operating the attachment This manual has been designed to help you do a better safer job Read this manual carefully and become familiar with its contents WARNING Never let anyone operate this unit without reading the Safety Precautions and Operating Instructions sections of this manual Always choose hard level ground to park the vehicle on and set the brake so the unit cannot roll Unless noted otherwise right and left sides are determined from the operator s control position when facing the attachment NOTE The illustrations and data used in this manual were current according to the information available to us at the time of printing However we reserve the right to redesign and change the attachment as may be necessa
35. ry without notification BEFORE OPERATION The primary responsibility for safety with this equipment falls to the operator Make sure the equipment is operated only by trained individuals who have read and understand this manual If there is any portion of this manual or function that you do not understand contact your local authorized dealer or the manufacturer SAFETY ALERT SYMBOL This is the Safety Alert Symbol used by this industry This symbol is used to warn A of possible injury Be sure to read all warnings carefully They are included for your safety and forthe safety of others working with you SERVICE When servicing your product remember to use only manufacturer replacement parts Substitute parts may not meet the standards required for safe dependable operation To facilitate parts ordering record the model and serial number of your unit in the space provided on the cover of this manual This information may be obtained from the identification plate located on the product The parts department needs this information to ensure that you receive the correct parts for your specific model M 934 9 21 05 2 76826 8 SAFETY STATEMENTS THIS SYMBOL BY ITSELF OR WITH A WARNING WORD THROUGHOUT THIS MAN UAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY OR THE SAFETY OF OTHERS FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH A DANGER THIS SIGNAL WORD IS USED WHERE SERIOUS I
36. th could result Never work under a raised attachment M 1998 7 30 08 76826 INSTALLATION AND OPERATION ATTACHING AND DETACHING SIDE SHIFT FORK CARRIAGE Please see your vehicle operator s manual for instructions on attaching and detaching your equipment WARNING To prevent serious personal injury or death only attach equipment that is H designed for your vehicle Specified lift capacities must not be exceeded otherwise machine stability will not be sufficient Always observe lift capacity limits listed in machine specifi cations OPERATING SIDE SHIFT FORK CARRIAGE Read all Safety Precautions before operating your new attachment For personal safety lower the attachment to the ground set the parking brake shut off engine and remove key before getting off of your prime mover SPECIAL OPERATING CONSIDERATIONS SIDE SHIFT FORK CARRIAGE OPERATION When using the side shift feature to pick up a load be sure to return the forks and loads to the center position as soon as possible Do NOT travel with loaded forks shifted to the side CYLINDERS IMPORTANT If your hydraulically operated attachment tilts or starts to drift due to oil leakage within the cylinder assembly discontinue use until the problem has been corrected M 1996 4 17 08 76826 9 INSTALLATION AND OPERATION FORK CARRIAGE OPERATION 1 Approach the load in such a fashion that the weight will be centered between the fork tines The heaviest side s
Download Pdf Manuals
Related Search